Copyrights in sync with "cid-gigabit.2020.06.05.tar.gz released by ND"
(from DPDK).
README from the latest em-7.7.8 on intel.com
Approved by: imp
MFC after: 1 week
This reverts commit fc7682b17f.
This will be done incrementally to help with bisecting an issue in
later I21x devices (ich8lan).
PR: 258153
Approved by: imp
MFC after: 1 day
Sync the e1000 shared code with DPDK shared code
"cid-gigabit.2020.06.05.tar.gz released by ND"
Primary focus was on client platforms (ich8lan). More work remains here
but we need an Intel contact for client networking.
Reviewed by: grehan, Intel Networking (erj, earlier rev)
Obtained from: DPDK <http://git.dpdk.org/dpdk/tree/drivers/net/e1000/base>
MFC after: 1 week
Sponsored by: me
Differential Revision: https://reviews.freebsd.org/D31547
Add support for current and future client platform PCI IDs. These are
all I219 variants and have no known driver changes versus previous
generation client platform I219 variants.
Reviewed by: markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D29801
This change introduces Comet Lake Mobile Platform support in the e1000
driver along with shared code patches described below.
- Cast return value of e1000_ltr2ns() to higher type to avoid overflow
- Remove useless statement of assigning act_offset
- Add initialization of identification LED
- Fix flow control setup after connected standby:
After connected standby the driver blocks resets during
"AdapterStart" and skips flow control setup. This change adds
condition in e1000_setup_link_ich8lan() to always setup flow control
and to setup physical interface only when there is no need to block
resets.
Signed-off-by: Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Submitted by: Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Reviewed by: erj@
Tested by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
MFC after: 1 week
Relnotes: yes
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D25035
A couple of drivers and one place in if.c use ETH_ADDR_LEN, even though
net/ethernet.h provides an equivalent ETHER_ADDR_LEN definition.
Cleanup all of the locations which refer to ETH_ADDR_LEN to use the
standard ETHER_ADDR_LEN instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Submitted by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed by: erj@, jpaetzel@
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D21239
With r333218 it is now possible for drivers to use an sx lock and thus sleep while
waiting on long running operations rather than DELAY().
Reported by: gallatin
Reviewed by: sbruno
Approved by: sbruno
MFC after: 1 month
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D14984
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
This was really too big of a commit even if everything worked, but there
are multiple new issues introduced in the one huge commit, so it's not
worth keeping this until it's fixed.
I'll work on splitting this up into logical chunks and introduce them one
at a time over the next week or two.
Approved by: sbruno (mentor)
Sponsored by: Limelight Networks
by Matt Macy as well as other changes which he has accepted via pull
request to his github repo at https://github.com/mattmacy/networking/
This should bring -CURRENT and the github repo into close enough sync to
allow small feature branches rather than a large chain of interdependant
patches being developed out of tree. The reset of the synchronization
should be able to be completed on github by splitting the remaining
changes that are not yet ready into short feature branches for later
review as smaller commits.
Here is a summary of changes included in this patch:
1) More checks when INVARIANTS are enabled for eariler problem
detection
2) Group Task Queue cleanups
- Fix use of duplicate shortdesc for gtaskqueue malloc type.
Some interfaces such as memguard(9) use the short description to
identify malloc types, so duplicates should be avoided.
3) Allow gtaskqueues to use ithreads in addition to taskqueues
- In some cases, this can improve performance
4) Better logging when taskqgroup_attach*() fails to set interrupt
affinity.
5) Do not start gtaskqueues until they're needed
6) Have mp_ring enqueue function enter the ABDICATED rather than BUSY
state. This moves the TX to the gtaskq and allows processing to
continue faster as well as make TX batching more likely.
7) Add an ift_txd_errata function to struct if_txrx. This allows
drivers to inspect/modify mbufs before transmission.
8) Add a new IFLIB_NEED_ZERO_CSUM for drivers to indicate they need
checksums zeroed for checksum offload to work. This avoids modifying
packet data in the TX path when possible.
9) Use ithreads for iflib I/O instead of taskqueues
10) Clean up ioctl and support async ioctl functions
11) Prefetch two cachlines from each mbuf instead of one up to 128B. We
often need to parse packet header info beyond 64B.
12) Fix potential memory corruption due to fence post error in
bit_nclear() usage.
13) Improved hang detection and handling
14) If the packet is smaller than MTU, disable the TSO flags.
This avoids extra packet parsing when not needed.
15) Move TCP header parsing inside the IS_TSO?() test.
This avoids extra packet parsing when not needed.
16) Pass chains of mbufs that are not consumed by lro to if_input()
rather call if_input() for each mbuf.
17) Re-arrange packet header loads to get as much work as possible done
before a cache stall.
18) Lock the context when calling IFDI_ATTACH_PRE()/IFDI_ATTACH_POST()/
IFDI_DETACH();
19) Attempt to distribute RX/TX tasks across cores more sensibly,
especially when RX and TX share an interrupt. RX will attempt to
take the first threads on a core, and TX will attempt to take
successive threads.
20) Allow iflib_softirq_alloc_generic() to request affinity to the same
cpus an interrupt has affinity with. This allows TX queues to
ensure they are serviced by the socket the device is on.
21) Add new iflib sysctls to net.iflib:
- timer_int - interval at which to run per-queue timers in ticks
- force_busdma
22) Add new per-device iflib sysctls to dev.X.Y.iflib
- rx_budget allows tuning the batch size on the RX path
- watchdog_events Count of watchdog events seen since load
23) Fix error where netmap_rxq_init() could get called before
IFDI_INIT()
24) e1000: Fixed version of r323008: post-cold sleep instead of DELAY
when waiting for firmware
- After interrupts are enabled, convert all waits to sleeps
- Eliminates e1000 software/firmware synchronization busy waits after
startup
25) e1000: Remove special case for budget=1 in em_txrx.c
- Premature optimization which may actually be incorrect with
multi-segment packets
26) e1000: Split out TX interrupt rather than share an interrupt for
RX and TX.
- Allows better performance by keeping RX and TX paths separate
27) e1000: Separate igb from em code where suitable
Much easier to understand separate functions and "if (is_igb)" than
previous tests like "if (reg_icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))"
#blamebruno
Reviewed by: sbruno
Approved by: sbruno (mentor)
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D12235
Post-cold sleep instead of DELAY when waiting for firmware.
Convert softc mutex to an SX lock. Change all waits to sleeps
once interrupts are enabled (and it is safe to sleep).
Submitted by: Matt Macy <matt@mattmacy.io>
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D12101
Two blocks in e1000_ich8lan.c are misaligned, causing noise with some
compilers (gcc 6).
Reviewed by: imp, erj
Differential Revision: https://reviews.freebsd.org/D10741
Major changes:
- Add i219/i219(2) hardware support. (Found on Skylake generation and newer
chipsets.)
- Further to the last Skylake support diff, this one also includes support for
the Lewisburg chipset (i219(3)).
- Add a workaround to an igb hardware errata.
All 1G server products need to have IPv6 extension header parsing turned off.
This should be listed in the specification updates for current 1G server
products, e.g. for i350 it's errata #37 in this document:
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/ethernet-controller-i350-spec-update.pdf
- Avoton (i354) PHY errata workaround added
And a bunch of minor fixes, as well as #defines for things that the current
em(4)/igb(4) drivers don't implement.
Differential Revision: https://reviews.freebsd.org/D3162
Reviewed by: sbruno, marius, gnn
Approved by: gnn
MFC after: 2 weeks
Sponsored by: Intel Corporation
to attach with the last version of this commit. This commit fixes
attach failures on "ICH8" class devices via modifications to
e1000_init_nvm_params_ich8lan()
- Fix compiler warning in 80003es2lan.c
- Add return value handler for e1000_*_kmrn_reg_80003es2lan
- Fix usage of DEBUGOUT
- Remove unnecessary variable initializations.
- Removed unused variables (complaints from gcc).
- Edit defines in 82571.h.
- Add workaround for igb hw errata.
- Shared code changes for Skylake/I219 support.
- Remove unused OBFF and LTR functions.
Tested by some of the folks that reported breakage in previous incarnation.
Thanks to AllanJude, gjb, gnn, tijl for tempting fate with their machines.
Submitted by: erj@freebsd.org
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D3162
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
- This version has support for the new Intel Avoton systems,
including 2.5Gb support, further it now has IPv6/TSO6 support as
well. Shared code has been updated where necessary as well. Thanks
to my new assistant Eric Joyner for doing the transmit path changes
to bring in the IPv6/TSO6 support. Thanks to Gleb for catching the
one bug and change needed in NETMAP.
Approved by: re
- bear with me, there are lots of white space changes, I would not
do them, but I am a mere consumer of this stuff and if these drivers
are to stay in shape they need to be taken.
em driver changes: support for the new i217/i218 interfaces
igb driver changes:
- TX mq start has a quick turnaround to the stack
- Link/media handling improvement
- When link status changes happen the current flow control state
will now be displayed.
- A few white space/style changes.
lem driver changes:
- the shared code uncovered a bogus write to the RLPML register
(which does not exist in this hardware) in the vlan code,this
is removed.
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
support of new deltas for both em and igb drivers.
Note that I am not able to track all the bugs fixed in
this code, I am a consumer of it as a component of my
core drivers. It is important to keep the FreeBSD drivers
up to date with it however.
One important note is there is a key fix for 82574 in this
update. Also, there are lots of white space changes, I am
not happy about them but have no control over it :)
- Sync shared code with Intel internal
- New client chipset support added
- em driver - fixes to 82574, limit queues to 1 but use MSIX
- em driver - large changes in TX checksum offload and tso
code, thanks to yongari.
- some small changes for watchdog issues.
- igb driver - local timer watchdog code was missing locking
this and a couple other watchdog related fixes.
- bug in rx discard found by Andrew Boyer, check for null pointer
MFC: a week
em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.
igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.
MFC in a week
igb now has a queue notion that has a single interrupt
with an RX/TX pair, this will reduce the total interrupts
seen on a system. Both em and igb have a new watchdog
method. igb has fixes from Pyun Yong-Hyeon that have
improved stability, thank you :)
I wish to MFC this for 7.3 asap, please test if able.
drivers. These add new hardware support, most importantly
the pch (i5 chipset) in the em driver. Also, both drivers
now have the simplified (and I hope improved) watchdog
code. The igb driver uses the new RX cleanup that I
first implemented in ixgbe.
em - version 6.9.24
igb - version 1.8.4
part that is made up of 8K banks rather than 4K, if these
systems are using bank 1 then the last change in this code
breaks the bank read, resulting in an invalid checksum of
the eeprom during driver load. This change fixes this.
Approved by: re
will sometimes fail to initialize problem due to a lock
contention with management hardware. However, in order to
deliver that fix it was necessary to take a shared code
update as a whole, and this required scattered changes in
the core code to be compatible.
The em driver now has VLAN HW support added as the igb
driver had previously.
MFC after: ASAP - in time for 7.1 RELEASE
proved to be necessary to make the static drivers work
in EITHER/OR or BOTH configurations. Modules will still
build in sys/modules/igb or em as before.
This also updates the igb driver for support for the 82576
adapter, adds shared code fixes, and etc....
MFC after: ASAP
