- Move the rtc_mtx spin lock out from under #ifdef SMP as it's just
not SMP-specific.
- Add a new spin lock pcib_mtx for locking "fast" interrupt handlers
of host-to-PCI bridge drivers on sparc64.
of the register rather than in the offset describing the register.
- In gem_reset_rx() let gem_bitwait() check for the Rx reset bit
rather than the Tx reset bit to clear.
Obtained from: OpenBSD (same/similar bugs being fixed)
These CPUs use an enhanced layout of the interrupt vector dispatch
and dispatch status registers in order to allow sending IPIs to
multiple targets simultaneously. Thus support for these CPUs was
put in a newly added cheetah_ipi_selected(). This is intended to
be pointed to by cpu_ipi_selected, which now is a function pointer,
in order to avoid cpu_impl checks once booted. Alternatively it
can point to spitfire_ipi_selected(), which was renamed from
cpu_ipi_selected(). Consequently cpu_ipi_send() was also renamed
to spitfire_ipi_send() (there's no need for a cheetah equivalent
of this so far). Initialization of the cpu_ipi_selected pointer
and other requirements is done in mp_init(), which was renamed
from mp_tramp_alloc(), as cpu_mp_start() isn't called on UP
systems while cpu_ipi_selected() is. As a side-effect this allows
to make mp_tramp static to sys/sparc64/sparc64/mp_machdep.c.
For the sake of avoiding #ifdef SMP and for keeping the history in
place cheetah_ipi_selected() and spitfire_ipi_{selected,send}()
where not put into/moved to sys/sparc64/sparc64/{cheetah,spitfire}.c
- Add some CTASSERTs and KASSERTs ensuring that MAXCPU doesn't
exceed the data types we use to store the CPU bit fields or the
number of USIII and greater CPUs supported by the current
cheetah_ipi_selected() implementation (which for JBus-CPUs is
only 4; that should be fine though as according to OpenSolaris
there are no sun4u machines with more than 4 JBus-CPUs).
- In cpu_mp_start() don't enumerate and start more than MAXCPU CPUs
as we can't handle more than that.
- In cpu_mp_start() check for upa-portid vs. portid depending on
cpu_impl for consistency with nexus(4).
- In spitfire_ipi_selected() add KASSERTs ensuring that a CPU isn't
told to IPI itself as sun4u CPUs just can't do that.
- In spitfire_ipi_send() do a MEMBAR #Sync after writing the
interrupt vector data as we want to make sure the payload was
actually written before we trigger the dispatch.
- In spitfire_ipi_send() also verify IDR_BUSY when checking whether
the dispatch was successful as it has to be cleared for this to
be the case.
- Remove some redundant variables.
RTC function of a National Semiconductor PC87317/PC97317. This
consists of using the century register the same way Solaris does
for compatibility reasons. Once there is a MD power(4) we'd also
want to interface the APC (Advanced Power Control) functionality
of the same chip function with it.
- Use a macro for the device description and take advantage of
ISA_PNP_PROBE() setting the device description.
- Use the generated typedefs for the prototypes of the device
interface functions.
reasons outlined in the comment removed along with it, because the
OFW hostid has no real meaning for FreeBSD and mainly so the OFW
hostid is not confused with the FreeBSD hostid.
moving OF_set_mmfsa_traptable() (SUNW,set-trap-table with the two
arguments used here is specific to sun4v) to MD code.
- In sys/dev/ofw/openfirm.h remove prototypes for unimplemented
functions and unused Solaris compatibility macros.
to be compiled into every driver making use of it. Use a const instance
of struct gfb_font for this as the font isn't intended to be changed at
run-time and in order to accompany the font data with height and width
info.
- Add missing prototypes.
- Define global variables not used outside of this module as static.
- Replace some outdated hard-coded functions names in panic strings
with __func__.
- Fix some style(9) bugs.
data and remove the array size from the definition as f.e. the gallant
12 x 22 font data is 256 * 44 in size, exceeding the previously hard-
coded size.
- Declare the bold8x16 instance of struct gfb_font as const as it's not
intended to be changed at run-time as a whole either.
- Use __FBSDID in xboxfb.c
Tested by: rink
the passed in auth_type is unacceptable to rpcauth_buildheader-
this avoids a null pointer panic. Clean up allocations if this
happens. This also quiets a gcc 4.2 complaint about ussing mheadend
without it being initialized.
Reviewed by: alfred
through wpa_supplcant. If a sta is deauth'd (e.g. due to inactivity)
with roaming mode set to manual then a subsequent MLME assoc request
will be incorrectly handled and the station will never reauthenticate.
To fix this interpret a reason code of zero as sufficient to send an
auth request frame.
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
eradication in/from userland path, countless locking fixes, etc.
- General sleep call through msleep(9) has been converted to condvar(9)
with better consistencies.
- Heavily guard every possible "slow path" entries (open(), close(),
few ioctl()s, sysctls), but once it entering "fast path" (io, interrupt
started), they are free to fly on their own.
- Rearrange locking sequences, resulting better concurrency and
serialization. Large part doesn't even need locking at all, and will be
removed in future. Less clutter, except in few places due to lock
ordering.
- Anonymous mixer object creation/deletion to simplify mixer handling
beyond typical mixer ioctls.
Submitted by: chibis (with modifications)
- Add few mix_[get|set|..] functions to avoid calling mixer_ioctl()
directly using cryptic arguments.
- Locking fixes to avoid possible deadlock with (still under Giant) USB.
- Better simplex/duplex device handling.
- Recover mmap() functionality for recording, which has been lost
since 2.2.x - 3.x (the introduction of newpcm). Full-duplex mmap still
doesn't work (due to VM/page design), but people still can mmap
both by opening each direction separately. mmaped playback is guarantee
to work either way.
- New sysctl: "hw.snd.compat_linux_mmap" to allow PROT_EXEC page
mapping, due to recent changes in linux compatibility layer which
require it. All linux applications that using sound + mmap() (mostly games)
require this to be enabled. Disabled by default.
- Other goodies.. too many, that will increase releng7 shareholder value
and make users of releng6 (and below) cry ;)
* This commit should be atomic. If anything goes wrong (not counting problem
originated from elsewhere), I will not hesitate to revert everything back
within 12 hours. This substantial changes itself not a rocket science
and the process has begun for almost 2 years, and lots of incremental
changes are already in place during that period of time.
* Some issues does occur in snd_emu10kx (note the 'x') due to various
internal locking issues and it is currently being worked on by chibis.
Tested by: chibis (Yuriy Tsibizov), joel, Alexandre Vieira,
many innocent souls...
Without bus_dma clean up and increment of number of Tx descriptors
it's hard to guarantee correct Tx operation in TSO case. The TSO
support would be enabled again when I get more feeback from re(4)
patch posted to current.
Please note that, this is currently considered as an
experimental feature so there could be some rough
edges. Consult http://wiki.freebsd.org/TMPFS for
more information.
For now, connect tmpfs to build on i386 and amd64
architectures only. Please let us know if you have
success with other platforms.
This work was developed by Julio M. Merino Vidal
for NetBSD as a SoC project; Rohit Jalan ported it
from NetBSD to FreeBSD. Howard Su and Glen Leeder
are worked on it to continue this effort.
Obtained from: NetBSD via p4
Submitted by: Howard Su (with some minor changes)
Approved by: re (kensmith)
- Remove unnecessary timestamps.
- Return CAM_RESRC_UNAVAIL for ORB shortage.
- Fix a lock problem when doorbell is used.
- Fix a potential bug for unordered execution.
'result' is still NULL and we do not need to free anything.
That allows us to gc the entire goto parts and a now unused variable.
Found with: Coverity Prevent(tm)
CID: 2519
do not continue with a NULL pointer. [1]
While here change the return of the error handling code path above.
I cannot see why we should always return 0 there. Neither does KAME
nor do we in here for the similar check in all the other functions.
Found with: Coverity Prevent(tm) [1]
CID: 2521
114 bytes of cmos ram in the PC clock chip. The big difference between
this and the Linux version is that we do not recalculate the checksums
for bytes 16..31.
We use this at work when cloning identical machines - we can copy the
bios settings as well. Reading /dev/nvram gives 114 bytes of data but
you can seek/read/write whichever bytes you like.
Yes, this is a "foot, gun, fire!" type of device.
without an mtag in ipsec4_common_input_cb.
So in case of !IPCOMP (AH,ESP) only change the m_tag_id if an mtag
was passed to ipsec4_common_input_cb.
Found with: Coverity Prevent(tm)
CID: 2523
handle, document those sprotos using an IPSEC_ASSERT so that it will
be clear that 'spi' will always be initialized when used the first time.
Found with: Coverity Prevent(tm)
CID: 2533
- In tdq_choose() only assert that a thread does not have too high a
priority (low value) for the queue we removed it from. This will catch
bugs in priority elevation. It's not a serious error for the thread
to have too low a priority as we don't change queues in this case as
an optimization.
Reported by: kris
thinking it had the whole chunk. This could cause a crash if
a large packet drop came in. Fixed by adjusting the trunc length
down to the limit.
- Large sacks with lots of segments could also have same issue. Changed
duplicate and segment handling to use proper get_m_ptr function to
pull each block from mbuf chains.
ioctl routines if we are running with !mpsafenet
- Change un-conditional Giant acquisition around ifpromisc
to occur only if we are running with !mpsafenet
With these locking bits in place, we can now remove the Giant
requirement from BPF, so drop the D_NEEDGIANT device flag.
This change removes Giant acquisitions around BPF device
handlers (read, write, ioctl etc).
MFC after: 1 month
Discussed with: rwatson
or idle priority of another process owned by the same user. This means
that privilege in rtprio(2) (and rtprio_thread(2)) is required indirectly
via p_cansched(9) or directly to set realtime/idle privilege, rather than
directly affecting target process authorization.
- Fix so VRF's will clean themselves up when no references are around.
- Allow sctp_ifa to be passed into inpcb_bind, addr_mgmt_ep_sa to bypass
normal validation checks.
- turn auto-asconf off for subset bound sockets
- Moves all logging to use KTR. This gets rid of most
of the logging #ifdef's with a few exceptions reducing
the number of config options for SCTP.
more exposure. The current state of SCTP implementation is
considered to be ready for 32-bit platforms, but still need some
work/testing on 64-bit platforms.
Approved by: re (kensmith)
Discussed with: rrs
Also, remove usb_malloc_type: it was unused.
Remove METHODS_NONE: it was unused.
Move include of opt_usb.h from usb_port.h to usb.h, since usb_port.h is
going away (there will be a usb_compat.h for out-of-tree drivers that want it).
- Depessimize userret() in kernels where KTRACE is enabled by doing an
unlocked check of the per-process queue of pending events before
acquiring any locks. Previously ktr_userret() unconditionally acquired
the global ktrace_sx lock on every return to userland for every thread,
even if ktrace wasn't enabled for the thread.
- Optimize the locking in exit() to first perform an unlocked read of
p_traceflag to see if ktrace is enabled and only acquire locks and
teardown ktrace if the test succeeds. Also, explicitly disable tracing
before draining any pending events so the pending events actually get
written out. The unlocked read is safe because proc lock is acquired
earlier after single-threading so p_traceflag can't change between then
and this check (well, it can currently due to a bug in ktrace I will fix
next, but that race existed prior to this change as well).
Reviewed by: rwatson
during execve() when turning off tracing due to executing a setuid binary
as non-root. Previously this could fail to acquire Giant and fail an
assertion if the ktrace file was on a non-MPSAFE filesystem and the
executable was on an MPSAFE filesystem.
MFC after: 3 days
Reported by: kris
bridged, previously legitimate traffic was not passed as the bridge could not
tell that it was on a different Ethernet segment.
All non-tagged traffic is treated as vlan1 as per IEEE 802.1Q-2003
than the 5288.
It is not correctly implemented in earlier silicon, and the BIOS often
lies about AHCI capability on platforms where these chips are deployed.
With this change I am able to boot FreeBSD on the ASUS Vintage AH-1
barebones system.
Approved by: sos
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
timing loops being optimized away.
Once apon a time, gcc promised not to optimize away timing loops, but
gcc started optimizing away the call to a null function in the timing
loop here some time between gcc-3.3.3 and gcc-3.4.6, and it started
optimizing away the timing loop itself some time between gcc-3.4.6
and gcc-4.2.
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
- Add and document the KVM and KVM_SUPPORT options that
are needed for the ifmcstats(3) makefile
- Garbage collect unused variables
- Add missing inclusion of bsd.own.mk where needed
Approved by: kan (mentor)
Reviewed by: ru
its an INIT collision case.
- Fixed RTO calc to maintain a seperate variable to track
if a RTO calc as been done, this allows the RTO var to be
doubled during initial timeouts.
- Reduces the amount of stack used by process control.
- Use a constant for the peer chunk overhead.
- Name change to spell candidate correctly.
- Remove unused kse fields from struct proc.
- Group remaining fields and #ifdef KSE them.
- Move some kern_kse.c only prototypes out of proc and into kern_kse.
Discussed with: Julian
and protocol-independent host mode multicast. The code is written to
accomodate IPv6, IGMPv3 and MLDv2 with only a little additional work.
This change only pertains to FreeBSD's use as a multicast end-station and
does not concern multicast routing; for an IGMPv3/MLDv2 router
implementation, consider the XORP project.
The work is based on Wilbert de Graaf's IGMPv3 code drop for FreeBSD 4.6,
which is available at: http://www.kloosterhof.com/wilbert/igmpv3.html
Summary
* IPv4 multicast socket processing is now moved out of ip_output.c
into a new module, in_mcast.c.
* The in_mcast.c module implements the IPv4 legacy any-source API in
terms of the protocol-independent source-specific API.
* Source filters are lazy allocated as the common case does not use them.
They are part of per inpcb state and are covered by the inpcb lock.
* struct ip_mreqn is now supported to allow applications to specify
multicast joins by interface index in the legacy IPv4 any-source API.
* In UDP, an incoming multicast datagram only requires that the source
port matches the 4-tuple if the socket was already bound by source port.
An unbound socket SHOULD be able to receive multicasts sent from an
ephemeral source port.
* The UDP socket multicast filter mode defaults to exclusive, that is,
sources present in the per-socket list will be blocked from delivery.
* The RFC 3678 userland functions have been added to libc: setsourcefilter,
getsourcefilter, setipv4sourcefilter, getipv4sourcefilter.
* Definitions for IGMPv3 are merged but not yet used.
* struct sockaddr_storage is now referenced from <netinet/in.h>. It
is therefore defined there if not already declared in the same way
as for the C99 types.
* The RFC 1724 hack (specify 0.0.0.0/8 addresses to IP_MULTICAST_IF
which are then interpreted as interface indexes) is now deprecated.
* A patch for the Rhyolite.com routed in the FreeBSD base system
is available in the -net archives. This only affects individuals
running RIPv1 or RIPv2 via point-to-point and/or unnumbered interfaces.
* Make IPv6 detach path similar to IPv4's in code flow; functionally same.
* Bump __FreeBSD_version to 700048; see UPDATING.
This work was financially supported by another FreeBSD committer.
Obtained from: p4://bms_netdev
Submitted by: Wilbert de Graaf (original work)
Reviewed by: rwatson (locking), silence from fenner,
net@ (but with encouragement)
but are a seperate call that can be re-used if needed.
- 64 bit issues
o re-arrange cookie so it is better 64 bit aligned
o For wire level things we need the packed attribute.
- Add a count of exiting threads, p_exitthreads, to struct proc.
- Increment p_exithreads when we set the deadthread in thread_exit().
- When we thread_stash() a deadthread use an atomic to drop the count.
- Spin until the p_exithreads count reaches 0 in thread_wait().
- Lock the last exiting thread momentarily to be certain that it has
exited cpu_throw().
- Restructure thread_wait(). It does not need a loop as there will only
ever be one thread.
Tested by: moose@opera.com
Reported by: kris, moose@opera.com
MCLBYTES for the segment size but it used too many Tx descriptors in
TSO case.
While I'm here adjust maximum size of the sum of all segment lengths
in a given DMA mapping to 65535, the maximum size, in bytes, of a IP
packet.
o s/printf/device_printf/g
o Nuke OpenBSDism.
o Nuke NetBSD/OpenBSD specific DMA sync operations.(we don't have a way
to sync a single descriptor within a DMA map.)
o Remove recursive mutex.
o bus_dma(9) clean up.
o 40bit DMA address support.
o Add protection for Rx map load failure.
o Fix a long standing bug for watchdog timeout. [1]
o Add additional protections, missing Tx completion interrupt, losing
start Tx command, for watchdog timeout.
o Switch to taskqueue(9) API to handle interrupts.
o Use our own timer for watchdog instead of if_watchdog/if_timer
interface.
o Advertise VLAN header length/capability correctly to upper layer.
o Remove excessive kernel stack consumption in nfe_encap().
o Handle highly fragmented mbuf chains correctly.
o Enable etherenet address reprogramming with ifconfig(8).
o Add ALTQ/TSO, MSI/MSIX support.
o Increased Rx ring to 256 descriptors from 128.
o Align Tx/Rx descriptor ring on sizeof(struct nfe_desc64) boundary.
o Remove alignment restrictions on Tx/Rx buffers.
o Rewritten jumbo frame support code.
o Add support for hardware assistend VLAN tag insertion/stripping.
o Add support for Tx/Rx flow control based on patches from Peer Chen. [2]
o Add a routine that detects whether ethernet address swap routines is
required. [3]
o Add a workaround that take MAC/PHY out of power down mode.
o Add suspend/resume support.
o style(9) and code clean up.
Special thanks to Shigeaki Tagashira, the original porter of nfe(4),
who submitted lots of patches, performed uncountable number of
regression tests and maintained nfe(4) for a long time. Without his
enthusiastic help and support I could never have completed this
overhauling task.
The only weak point of nfe(4) compared to nve(4) is instability of
manual half-duplex media selection on certain hardwares(auto sensing
media type should work for all cases, though). This was a long
standing bug of nfe(4) and I still have no idea why it doesn't work
on some hardwares.
Obtained from: OpenBSD [1]
Submitted by: Peer Chen < pchen at nvidia dot com > [2], [3]
Reviewed by: Shigeaki Tagashira < shigeaki AT se DOT hiroshima-u DOT ac DOT jp >
Tested by: Shigeaki Tagashira, current
Discussed with: current
Silence from: obrien
some cases, move to priv_check() if it was an operation on a thread and
no other flags were present.
Eliminate caller-side jail exception checking (also now-unused); jail
privilege exception code now goes solely in kern_jail.c.
We can't yet eliminate suser() due to some cases in the KAME code where
a privilege check is performed and then used in many different deferred
paths. Do, however, move those prototypes to priv.h.
Reviewed by: csjp
Obtained from: TrustedBSD Project
- Allow LRO to be enabled / disabled at runtime
- Fix a double-free at module unload time.
- Only update timestamp in lro merge when it is present in the frame
Sponsored by: Myricom
- Use a seperate taskqueue+thread for reset tasks since iwi_ops will
block.
- Return from iwi_ops if the interface has been downed
- The firmware will fail if we are already associated
- Add myself to the copyright
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
MCLBYTES for the segment size but it used too many Tx descriptors in
TSO case.
While I'm here adjust maximum size of the sum of all segment lengths
in a given DMA mapping to 65535, the maximum size, in bytes, of a IP
packet.
making the relevant files standard. This avoids duplication and
makes it easier to override/disable unwanted schemes. Since ARM
doesn't have a DEFAULTS configuration file, leave the source
files for the BSD and MBR partitioning schemes in files.arm for
now.
- Add codec id for AD1988B, along with fixing its line-in and other
issues (with proper quirks). [2]
Submitted by: [1] barbara.xxx1975@libero.it
[2] Oliver Brandmueller ob@e-Gitt.NET
MFC after: 3 days
In particular:
- Add an explicative table for locking of struct vmmeter members
- Apply new rules for some of those members
- Remove some unuseful comments
Heavily reviewed by: alc, bde, jeff
Approved by: jeff (mentor)
be called with an incorrect segment end value. tcp_reass() may
trim segments when they overlap with already existing ones in the
reassembly queue. Instead of saving the segment end value before
the call to tcp_reass() compute it on the fly based on the effective
segment length afterwards.
This bug was not really problematic as no information got lost and
the eventual SACK information computation was correct nontheless.
MFC after: 1 week
instead of an authentication function. There are a design reason
and a practical reason for that. First, the module belongs in
account management because it checks availability of the account
and does no authentication. Second, there are existing and potential
PAM consumers that skip PAM authentication for good or for bad.
E.g., sshd(8) just prefers internal routines for public key auth;
OTOH, cron(8) and atrun(8) do implicit authentication when running
a job on behalf of its owner, so their inability to use PAM auth
is fundamental, but they can benefit from PAM account management.
Document this change in the manpage.
Modify /etc/pam.d files accordingly, so that pam_nologin.so is listed
under the "account" function class.
Bump __FreeBSD_version (mostly for ports, as this change should be
invisible to C code outside pam_nologin.)
PR: bin/112574
Approved by: des, re
is really a memory mapped I/O address. The bug is in the GAS that
describes the address and in particular the SpaceId field. The field
should not say the address is an I/O port when it clearly is not.
With an additional check for the IA64_BUS_SPACE_IO case in the bus
access functions, and the fact that I/O ports pretty much not used
in general on ia64, make the calculation of the I/O port address a
function. This avoids inlining the work-around into every driver,
and also helps reduce overall code bloat.
builds had been succeeding if run serially but could fail if run in
parallel because the bge module build might start before ofw_bus_if.h
got created as part of the mainline kernel build.
Diagnosis and patch by: ru
to the build.
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
caches with data caches after writing to memory. This typically
is required to make breakpoints work on ia64 and powerpc. For
those architectures the function is implemented.
This patch fixes places where they should be called atomically changing
their locking requirements (both assume per-proc spinlock held) and
introducing rufetchcalc which wrappers both calls to be performed in
atomic way.
Reviewed by: jeff
Approved by: jeff (mentor)
in tcp_outout(). This is currently not strictly necessary but paves
the way to simplify the entire SYN options handling quite a bit.
Clarify comment. No change in effective behavour with this commit.
RFC1323 requires the window field in a SYN (i.e., a <SYN> or
<SYN,ACK>) segment itself never be scaled.
and simplify handling of the send/receive window scaling. No
change in effective behavour.
RFC1323 requires the window field in a SYN (i.e., a <SYN> or
<SYN,ACK>) segment itself never be scaled.
Noticed by: yar
- Unsafeness on ruadd() in thread_exit()
- Unatomicity of thread_exiit() in the exit1() operations
This patch addresses these problems allocating p_fd as part of the
process and modifying the way it is accessed.
A small chunk of this patch, resolves a race about p_state in kern_wait(),
since we have to be sure about the zombif-ing process.
Submitted by: jeff
Approved by: jeff (mentor)
a timer issues a shutdown and a simultaneous close on the socket
happens. This race condition is inherent in the current socket/
inpcb life cycle system but can be handled well.
Reported by: kris
Tested by: kris (on 8-core machine)
- Reorder send failed to be in correct order.
- Fixed calulation of init-ack to be right off
mbuf lengths instead of the precalculated value. This
will fix one 64 bit platform issue.
error doing so. It seems an increasing number of phones have this
quirk, and we're not keeping up. There appears to be nothing bad that
happens for non-quirked phones.
Minor cleanups:
o prefer device_printf over printf
o kill devinfo stuff
o minor other preening.
need to do it at all anymore. Remove it from here. Expand
USB_ATTACH_SETUP inline now that it is one line and we're moving away
from the compat macros. Remove some bzero calls that turn out not be
be necessary.
what we print, don't print it anymore. And don't compute it anymore.
And don't malloc/free memory for it anymore. While I'm here, prefer
device_printf where appropriate.
the value of ph_nhooks to zero, not the address. This removes
extranious calls to pfil_run_hooks (and an rw lock) from the
network stack's critical path when no pfil hooks are active.
Reviewed by: csjp
Sponsored by: Myricom Inc.
implementing some of them using existing ones.
- Allow to compile ZFS on all archs and use atomic operations surrounded
by global mutex on archs we don't have or can't have all atomic
operations needed by ZFS.
algoritm would not go through the proper initialization.
- The initialization was incorrect as well, causing problems in
sat networks with > 1sec RTT
- Get rid of magic numbers in RTT calculations.
A change to dconschat(8) will follow so that it can bomb
this address over FireWire to reset a wedged system.
Though this method is just a hack and far from perfection,
it should be useful if you don't want to go machine room
just to reset or to power-cycle a machine without
remote-managed power supply. And much better than doing:
# fwcontrol -m target-eui64
# dd if=/dev/zero of=/dev/fwmem0.2 bs=1m
Now, it's safe to call the fwohci interrupt(polling) routine while ddb/gdb
is active. After this change, a dcons connnection over FireWire can survive
bus resets even in kernel debugger.
This means that it is not too late to plug a FireWire cable after a panic
to investigate the problem.
Actually there is a small window(between a jump to kernel from loader and
initialization of dcons_crom) in which no one can take care of a bus reset.
Except that window, firewire console should keep working
from loader to reboot even with a panic and a bus reset.
(as far as you enable LOADER_FIREWIRE_SUPPORT)
embedded storage in struct ucred. This allows audit state to be cached
with the thread, avoiding locking operations with each system call, and
makes it available in asynchronous execution contexts, such as deep in
the network stack or VFS.
Reviewed by: csjp
Approved by: re (kensmith)
Obtained from: TrustedBSD Project
cache size limit but this bucket row is empty. Normally we want to
recycle the oldest entry in the bucket row. If there isn't any the
TAILQ_REMOVE leads to a panic by trying to remove a non-existing
element. Fix this by just returning NULL and failing the insert.
This is not a problem as the TCP hostache is only advisory.
Submitted by: jhb
