If you had a UFS2 FS that didn't have it's super block at SBLOCK_UFS2,
you'll end up corrupting your FS as the superblock is updated and written
to a different location...
makefs used to put the superblock at SBLOCK_UFS1 for UFS 2 FS's causing
this issue...
Reviewed by: silience from mckusick
MFC after: 1 week
selection. gethrtime() in our port updated with HZ rate, so unusable for
this specific purpose, completely draining benefit of multiple taskqueues.
MFC after: 2 weeks
(7-bit device address << 1), always leaving the room for the read/write bit.
This commit convert ti_i2c and revert r259127 on bcm2835_bsc to make them
compatible with 8-bit addresses. Previous to this commit an i2c device
would have different addresses depending on the controller it was attached
to (by example, when compared to any iicbb(4) based i2c controller), which
was a pretty annoying behavior.
Also, update the PMIC i2c address on beaglebone* DTS files to match the new
address scheme.
Now the userland utilities need to do the correct slave address shifting
(but it is going to work with any i2c controller on the system).
Discussed with: ian
MFC after: 2 weeks
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
o Always init locks and cv ASAP.
o Initialize driver-independent parts even if driver probing fail.
o Allow to call vt_upgrade anytime, for later loaded drivers.
o New window flag VWF_READY, to track if window already initialized.
Other updates:
o Pass vd as a cookie for kbd_allocate.
o Do not blank window on driver replacement.
Tested by: hselasky (RPi), emaste(VGA, EFIFB, KMS), me
MFC after: 7 days
Sponsored by: The FreeBSD Foundation
Make it really work for native FreeBSD programs. Before this it was broken
for years due to different number of pointer dereferences in Linux and
FreeBSD IOCTL paths, permanently returning errors to FreeBSD programs.
This change breaks the driver FreeBSD IOCTL ABI, making it more strict,
but since it was not working any way -- who bother.
Add shims for 32-bit programs on 64-bit host, translating the argument
of the SG_IO IOCTL for both FreeBSD and Linux ABIs.
With this change I was able to run 32-bit Linux sg3_utils tools and simple
32 and 64-bit FreeBSD test tools on both 32 and 64-bit FreeBSD systems.
MFC after: 1 month
interface allows the ifnet structure to be defined as an opaque
type in NIC drivers. This then allows the ifnet structure to be
changed without a need to change or recompile NIC drivers.
Put differently, NIC drivers can be written and compiled once and
be used with different network stack implementations, provided of
course that those network stack implementations have an API and
ABI compatible interface.
This commit introduces the 'if_t' type to replace 'struct ifnet *'
as the type of a network interface. The 'if_t' type is defined as
'void *' to enable the compiler to perform type conversion to
'struct ifnet *' and vice versa where needed and without warnings.
The functions that implement the API are the only functions that
need to have an explicit cast.
The MII code has been converted to use the driver API to avoid
unnecessary code churn. Code churn comes from having to work with
both converted and unconverted drivers in correlation with having
callback functions that take an interface. By converting the MII
code first, the callback functions can be defined so that the
compiler will perform the typecasts automatically.
As soon as all drivers have been converted, the if_t type can be
redefined as needed and the API functions can be fix to not need
an explicit cast.
The immediate benefactors of this change are:
1. Juniper Networks - The network stack implementation in Junos
is entirely different from FreeBSD's one and this change
allows Juniper to build "stock" NIC drivers that can be used
in combination with both the FreeBSD and Junos stacks.
2. FreeBSD - This change opens the door towards changing ifnet
and implementing new features and optimizations in the network
stack without it requiring a change in the many NIC drivers
FreeBSD has.
Submitted by: Anuranjan Shukla <anshukla@juniper.net>
Reviewed by: glebius@
Obtained from: Juniper Networks, Inc.
through a voltage divisor (R163 and R164 on page 4 of BBB schematic).
Add a note about this on ti_adc(4) man page. The ti_adc(4) man page will
first appear on 10.1-RELEASE.
MFC after: 1 week
Suggested by: Sulev-Madis Silber (ketas)
Manual page reviewed by: brueffer (D127)
Reorganize the previous contexts of the file as it is in Linux. The
eventual goal is to install the header files and share them between
the kernel and bhyve.
MFC after: 1 week
This _was_ right, a last minute suggestion and not enough testing makes
Adrian a bad boy.
Tested:
* igb(4) with RSS patches, by hand verifying each igb(4) taskqueue
tid from procstat -ka using cpuset -g -t <tid>.
If the user specifies in /boot/loader.conf:
loader_brand="mycustom-brand"
Then "mycustom-brand" will be executed instead of "fbsd-logo".
Submitted by: alfred
Obtained from: FreeNAS
and the actual PWM frequency.
Enforce the maximum value for the period sysctl.
The frequency systcl now allows the direct setting of the PWM frequency (it
will try to find the better clkdiv and period for a given frequency, i.e.
the ones that will give the better PWM resolution).
This allows the use lower frequencies on the PWM. Without changing the
clock prescaler the minimum PWM frequency was 1.52kHz.
PWM frequencies checked with an osciloscope.
PWM output tested with some R/C servos at 50Hz.
it implicitly in vmm.ko.
Add ioctl VM_GET_CPUS to get the current set of 'active' and 'suspended' cpus
and display them via /usr/sbin/bhyvectl using the "--get-active-cpus" and
"--get-suspended-cpus" options.
This is in preparation for being able to reset virtual machine state without
having to destroy and recreate it.
flag has been added instead of FUTEX_WAIT to replace the FUTEX_WAIT
logic which needs to do gettimeofday() calls before the futex syscall
to convert the absolute timeout to a relative timeout.
Before this the CLOCK_MONOTONIC used by the FUTEX_WAIT_BITSET op.
When the FUTEX_CLOCK_REALTIME is specified the timeout is an absolute
time, not a relative time. Rework futex_wait to handle this.
On the side fix the futex leak in error case and remove useless
parentheses.
Properly calculate the timeout for the CLOCK_MONOTONIC case.
MFC after: 3 days
At attach, print the SCL and SDA pin numbers.
Remove a stray blank line.
Remove the GPIOBUS locking from gpioiic_reset(), it is already called with
this lock held. This fixes a crash when you try to scan the iicbus with
i2c(8).
get_scatter_segment() in get_fl_payload() fails. While here,
fix the code to adjust fl_bufs_used when a failure occurs for
any other scatter segment.
MFC after: 3 days
- Make the USB boot library more configurable.
- Resolve compile issues when cross building.
- Allow use of separate malloc.
- Allow use of separate endian macros.
Sponsored by: DARPA, AFRL
o Allow setting keymap in FDT, use hardcoded one by default
o Represent fallback keymap as a list rather than directly usable M*N array
Submitted by: Maxim Ignatenko <gelraen.ua@gmail.com>
current RADXA config. Radxa Rock (RR) boards have few types such as
RR (full version), RR Lite and some variants of RR engineering samples.
Add kernel config and FDT file for RR Lite board.
Approved by: stas (mentor)
If a vt(4) font does not exactly fit the screen dimensions, the console
window is offset so that it is centered. A rectangle is drawn at the
top, left, right, and bottom of the screen, to erase any leftovers that
are outside of the new usable console area.
If the x offset or y offset is 0 then the left border or top border
respectively is not drawn. The right and bottom borders may be one
pixel larger than necessary due to rounding, and are always drawn.
Prior to this change a 0 offset would result in a panic when calling
vt_drawrect with an x or y coordinate of -1.
Sponsored by: The FreeBSD Foundation
vt_grow may be called with a new size that's larger than previous but
does not require reallocation - for example, when the number of columns
is the same and new number of rows is less than the history size.
Prior to this change we would fail to update vb_scr_size, and then hit
a KASSERT when trying to write to the newly visible rows.
Sponsored by: The FreeBSD Foundation
ifa_ifwithnet() and ifa_ifwithdstaddr() The legacy functions will call the
_fib() versions with RT_ALL_FIBS, preserving legacy behavior.
sys/net/if_var.h
sys/net/if.c
Add legacy-compatible functions as described above. Ensure legacy
behavior when RT_ALL_FIBS is passed as fibnum.
sys/netinet/in_pcb.c
sys/netinet/ip_output.c
sys/netinet/ip_options.c
sys/net/route.c
sys/net/rtsock.c
sys/netinet6/nd6.c
Call with _fib() functions if we must use a specific fib, or the
legacy functions otherwise.
tests/sys/netinet/fibs_test.sh
tests/sys/netinet/udp_dontroute.c
Improve the udp_dontroute test. The bug that this test exercises is
that ifa_ifwithnet() will return the wrong address, if multiple
interfaces have addresses on the same subnet but with different
fibs. The previous version of the test only considered one possible
failure mode: that ifa_ifwithnet_fib() might fail to find any
suitable address at all. The new version also checks whether
ifa_ifwithnet_fib() finds the correct address by checking where the
ARP request goes.
Reported by: bz, hrs
Reviewed by: hrs
MFC after: 1 week
X-MFC-with: 264905
Sponsored by: Spectra Logic
(XScale mainly) expects the memory located before the kernel to be mapped,
and use it to allocate the page tables, the various stacks, etc.
A better fix would probably be to rewrite the various bla_machdep.c to stop
using that RAM, but I'm not so inclined to do it, especially since I don't
have hardware for all of them.
correctly prepare KGSBASE msr to restore the user descriptor base on
the last swapgs during return to usermode.
Reported and tested by: peterj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
mode.
Put the htonl(), htons(), ntohl() and ntohs() declarations under
__POSIX_VISIBLE >= 200112. POSIX.1-2001 and newer require these to be
exposed from <netinet/in.h> (as well as <arpa/inet.h>).
Note that it may be unnecessary to check __POSIX_VISIBLE >= 200112 because
older versions of POSIX and the C standard do not define this header.
However, other places in the same file already perform the check.
PR: 188316
Submitted by: Christian Neukirchen
- Update FDT file for BERI DE4 boards.
- Add needed kernel configuration keywords.
- Rename module to saf1761otg so that the device unit number does not
interfere with the hardware ID in dmesg.
Sponsored by: DARPA, AFRL
- Use an interrupt filter for handling the data path interrupts. This
increases the throughput significantly.
- Implement support for USB suspend and resume in USB host mode.
Sponsored by: DARPA, AFRL
they then pick up an opt_global.h from KERNBUILDDIR having PAE defined.
Thus, build all modules by default except those which still really are
defective as of r266799.
- Minor style cleanup.
MFC after: 1 week
flags that has several bits cleared. The RF_WANTED and RF_FIRSTSHARE
bits are invalid in this context, and we want to defer setting RF_ACTIVE
in r_flags until later. This should make rman_get_flags() return
the correct answer in all cases.
Add a KASSERT() to catch callers which incorrectly pass the RF_WANTED
or RF_FIRSTSHARE flags.
Do a strict equality check on the share type bits of flags. In
particular, do an equality check on RF_PREFETCHABLE. The previous
code would allow one type of mismatch of RF_PREFETCHABLE but disallow
the other type of mismatch. Also, ignore the the RF_ALIGNMENT_MASK
bits since alignment validity should be handled by the amask check.
This field contains an integer value, but previous code did a strange
bitwise comparison on it.
Leave the original value of flags unmolested as a minor debug aid.
Change the start+amask overflow check to a KASSERT() since it is just
meant to catch a highly unlikely programming error in the caller.
Reviewed by: jhb
MFC after: 1 month
- Make the USB hardware skip PTDs which are not allocated.
- Peek host memory twice. Sometimes the PTD status is incorrectly
returned as zero.
- Ensure the host channel is always freed when software TD
is completing.
- Add correct configuration of interrupt polarity and type.
- Set CERR to 2 for asynchronous traffic to avoid having to
reactivate the PTD when a NAK token is received.
- Fix detection of STALL PID.
Sponsored by: DARPA, AFRL
For IPv6-in-IPv4, you may need to do the following command
on the tunnel interface if it is configured as IPv4 only:
ifconfig <interface> inet6 -ifdisabled
Code logic inspired from NetBSD.
PR: kern/169438
Submitted by: emeric.poupon@netasq.com
Reviewed by: fabient, ae
Obtained from: NETASQ
physical addresses.
- Nuke the unused softc of emujoy(4).
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
MFC after: 3 days
Sponsored by: Bally Wulff Games & Entertainment GmbH
- Based on actual usage and on what Linux does, dummy_page.addr should
contain the physical bus address of the dummy page rather than its
virtual one. As a side-effect, correcting this bug fixes compilation
with PAE support enabled by getting rid of an inappropriate cast.
- Also based on actual usage of dummy_page.addr, theoretically Radeon
devices could do a maximum of 44-bit DMA. In reality, though, it is
more likely that they only support 32-bit DMA, at least that is what
radeon_gart_table_ram_alloc() sets up for, too. However, passing ~0
to drm_pci_alloc() as maxaddr parameter translates to 64-bit DMA on
amd64/64-bit machines. Thus, use BUS_SPACE_MAXSIZE_32BIT instead,
which the existing 32-bit DMA limits within the drm2 code spelled as
0xFFFFFFFF should also be changed to.
Reviewed by: dumbbell
MFC after: 1 week
Sponsored by: Bally Wulff Games & Entertainment GmbH
Some Linux futex ops atomically verifies that the futex address uaddr
(uval) contains the value val. Comparing signed uval and unsigned val
may lead to an unexpected result, mostly to a deadlock.
So copyin uaddr to an unsigned int to compare the parameters correctly.
While here change ktr records to print parameters in more readable format.
Tested by eadler@
MFC after: 3 days
situation checked by assert is verified to not take place in
vm_map_wire(), and protection permissions on the wired entry can be
revoked afterward.
Reported by: markj
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
was not allocating space for the parameter save area in the stack frame.
If the compiler chose to save the argument to the signal handler on the
stack, it would overwrite the first 32 bits of the sigaction struct with
it, corrupting it for a subsequent invocation.
PR: powerpc/183040
MFC after: 8 days
BUS_DMA_KMEM_ALLOC. They serve the same purpose, but using the flag
means that the map can be NULL again, which in turn enables significant
optimizations for the common case of no bouncing.
Obtained from: Netflix, Inc.
MFC after: 3 days
- Switch from timeout() to callout_*() for per-request timers.
- Use device_find_child() in the identify routine.
- Use device_printf() instead of passing device_get_nameunit() to
printf().
- Expand the SBP_LOCK coverage simplifying the locking.
- Uninline STAILQ_FOREACH_SAFE().
Tested by: sbruno
Add a new zfs property, "redundant_metadata" which can have values "all" or
"most". The default will be "all", which is the current behavior. When set
to all, ZFS stores an extra copy of all metadata. If a single on-disk block
is corrupt, at worst a single block of user data (which is recordsize bytes
long) can be lost.
Setting to "most" will cause us to only store 1 copy of level-1 indirect
blocks of user data files. This can improve performance of random writes,
because less metadata has to be written. In practice, at worst about
100 blocks (of recordsize bytes each) of user data can be lost if a single
on-disk block is corrupt.
The exact behavior of which metadata blocks are stored redundantly may change
in future releases.
Illumos issue: 3835 zfs need not store 2 copies of all metadata
MFC after: 2 weeks
guest for which the rules regarding xsetbv emulation are known. In
particular future extensions like AVX-512 have interdependencies among
feature bits that could allow a guest to trigger a GP# in the host with
the current approach of allowing anything the host supports.
- Add proper checking of Intel MPX and AVX-512 XSAVE features in the
xsetbv emulation and allow these features to be exposed to the guest if
they are enabled in the host.
- Expose a subset of known-safe features from leaf 0 of the structured
extended features to guests if they are supported on the host including
RDFSBASE/RDGSBASE, BMI1/2, AVX2, AVX-512, HLE, ERMS, and RTM. Aside
from AVX-512, these features are all new instructions available for use
in ring 3 with no additional hypervisor changes needed.
Reviewed by: neel
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
Relnotes: Yes
Sponsored by: Chelsio Communications.
uart2: <Intel AMT - PM965/GM965 KT Controller> port 0x1830-0x1837
mem 0xfe024000-0xfe024fff irq 17 at device 3.3 on pci0
uart2: console (115200,n,8,1)
Tested as tty and serial console. Seems "fine"
- Put "_LE_" into the register access macros to indicate little endian
byte order is expected by the hardware.
- Avoid using the bounce buffer when not strictly needed. Try to move
data directly using bus-space functions first.
- Ensure we preserve the reserved bits in the power down mode
register. Else the hardware goes into a non-recoverable state.
- Always use 32-bit access when writing or reading registers or FIFOs,
because the hardware is 32-bit oriented and don't really understand 8-
and 16-bit access.
- Correct writes to the memory address register. There is no need to
shift the register offset.
- Correct interval for interrupt endpoints.
- Optimise 90ns internal memory buffer read delay.
- Rename PDT into PTD, which is how the datasheet writes it.
- Add missing programming for activating host controller PTDs.
Sponsored by: DARPA, AFRL
mappings. Instead, they should be first mapping to an RSS bucket and
then querying the RSS bucket -> CPU ID mapping to figure out the target
CPU.
When (if?) RSS rebalancing is implemented or some other (non round-robin)
distribution of work from buckets to CPU IDs, various bits of code - both
userland and kernel - will need to know how this mapping works.
So, to support this:
* Add a new function rss_m2bucket() - this maps an mbuf to a given bucket.
Anything which is currently doing hash -> CPU work may instead wish to
do hash -> bucket, and then query the bucket->cpuid map for which
CPU it belongs on. Or, map it to a bucket, then re-pin that bucket ->
CPU during a rebalance operation.
* For userland applications which wish to exploit affinity to RSS buckets,
the bucket -> CPU ID mapping is now available via a sysctl.
net.inet.rss.bucket_mapping lists the bucket to CPU ID mapping via
a list of bucket:cpu pairs.
Use armv7_setttb that sets proper PT attributes.
Get rid of unused CPU functions, put nullop instead.
Exchange obsolete pj4b_/arm11_ functions to the appropriate armv7_ ones.
API function 'vie_calculate_gla()'.
While the current implementation is simplistic it forms the basis of doing
segmentation checks if the guest is in 32-bit protected mode.
of the guest linear address space. These APIs in turn use a new ioctl
'VM_GLA2GPA' to convert the guest linear address to guest physical.
Use the new copyin/copyout APIs when emulating ins/outs instruction in
bhyve(8).
taskqueue worker thread(s) to.
For now it isn't a taskqueue/taskthread error to fail to pin
to the given cpuid.
Thanks to rpaulo@, kib@ and jhb@ for feedback.
Tested:
* igb(4), with local RSS patches to pin taskqueues.
TODO:
* ask the doc team for help in documenting the new API call.
* add a taskqueue_start_threads_cpuset() method which takes
a cpuset_t - but this may require a bunch of surgery to
bring cpuset_t into scope.
'struct vm_guest_paging'.
Check for canonical addressing in vmm_gla2gpa() and inject a protection
fault into the guest if a violation is detected.
If the page table walk is restarted in vmm_gla2gpa() then reset 'ptpphys' to
point to the root of the page tables.
indicate the faulting linear address.
If the guest PML4 entry has the PG_PS bit set then inject a page fault into
the guest with the PGEX_RSV bit set in the error_code.
Get rid of redundant checks for the PG_RW violations when walking the page
tables.
memory ordering model allows writes to different devices to complete out
of order, leading to a situation where the write that clears an interrupt
source at a device can complete after a write that unmasks and EOIs the
interrupt at the interrupt controller, leading to a spurious re-interrupt.
This adds a generic barrier function specific to the needs of interrupt
controllers, and calls that function from the GIC and TI AINTC controllers.
There may still be other soc-specific controllers that need to make the call.
Reviewed by: cognet, Svatopluk Kraus <onwahe@gmail.com>
MFC after: 3 days
Idle priority is not even time-share, so if system is busy in any way,
those events may never be executed. Since in some cases system waits
for events processed by that thread, that may cause deadlocks.
to be consistent with mutex destruction in ipf_log_soft_destroy(). As a
result mutex destruction in ipf_log_soft_fini() is redundant.
Approved by: glebius (mentor)
Obtained from: darrenr (author)
the kmem object lock is held. Do the pmap_remove() before acquiring the
kmem object lock.
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
The CUSE library is a wrapper for the devfs kernel functionality which
is exposed through /dev/cuse . In order to function the CUSE kernel
code must either be enabled in the kernel configuration file or loaded
separately as a module. Currently none of the committed items are
connected to the default builds, except for installing the needed
header files. The CUSE code will be connected to the default world and
kernel builds in a follow-up commit.
The CUSE module was written by Hans Petter Selasky, somewhat inspired
by similar functionality found in FUSE. The CUSE library can be used
for many purposes. Currently CUSE is used when running Linux kernel
drivers in user-space, which need to create a character device node to
communicate with its applications. CUSE has full support for almost
all devfs functionality found in the kernel:
- kevents
- read
- write
- ioctl
- poll
- open
- close
- mmap
- private per file handle data
Requested by several people. Also see "multimedia/cuse4bsd-kmod" in
ports.
the UART FIFO.
The emulation is constrained in a number of ways: 64-bit only, doesn't check
for all exception conditions, limited to i/o ports emulated in userspace.
Some of these constraints will be relaxed in followup commits.
Requested by: grehan
Reviewed by: tychon (partially and a much earlier version)
the proper ICWx initialization sequence. It assumes, probably correctly, that
the boot firmware has done the 8259 initialization.
Since grub-bhyve does not initialize the 8259 this write to the mask register
takes a code path in which 'error' remains uninitialized (ready=0,icw_num=0).
Fix this by initializing 'error' at the start of the function.
shared flag is set on normal-memory mappings made via pmap_kenter() for SMP.
The "shared flag" part of this change isn't obvious from the diff, here's
the deal... by using the array of preformatted page table entry templates
instead of constructing the PTE from scratch, we automatically get the
right attribute bits set for both caching and shared.
MFC after: 1 week
These masks are documented in the Intel Architecture Instruction Set
Extensions Programming Reference (March 2014).
Reviewed by: kib
MFC after: 1 month
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
"fatal firmware error" happens. Previously it was neccessary to reset
it manually, using "/etc/rc.d/netif restart".
Approved by: adrian@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
direction isochronous transfers.
- Remove setting of fields which does not belong to the respective
TRBs. These fields are currently set as zero and this is more a
cosmetic change.
MFC after: 3 days
Submitted by: Horse Ma <HMa@wyse.com>
Quite often it can be just packet reorder, and killing link in such case
is inconvenient. Add few sysctl's to control that behavior.
PR: kern/182212
Submitted by: Eugene Grosbein <egrosbein@rdtc.ru>
MFC after: 2 weeks
- Make sure TX/RX lists don't leak and are only allocated once.
- Fix off-by one transfer index computation.
- Give firmware loading more time.
MFC after: 3 days
be a race when using a single active queue for all transmit types.
- Last argument of usb_pause_mtx() is ticks and not milliseconds.
- Remove unused watchdog.
- Remove some unused fields from the RSU softc structure.
- Workaround usbd_transfer_start() recursion from inside of completion
callback.
MFC after: 3 days
- Need to set the pre-fetch memory address when reading the host memory.
- We currently assume that no endianness conversion is needed.
Sponsored by: DARPA, AFRL
Assert that the hold count has not fallen below the use count, a situation
that would only happen when a vref() (or similar) is erroneously paired
with a vdrop(). This situation has not been observed in the wild, but
could be helpful for someone implementing a new filesystem.
Reviewed by: kib
Approved by: hrs (mentor)
boundary. This was addressed several years ago by creating a parent
tag hierarchy for the root buses that set the boundary restriction
for appropriate buses and allowed child deviced to inherit it.
Somewhere along the way, this restriction was turned into a case for
marking the tag as a candidate for needing bounce buffers, instead
of just splitting the segment along the boundary line. This flag
also causes all maps associated with this tag to be non-NULL, which
in turn causes bus_dmamap_sync() to take the slow path of function
pointer indirection to discover that there's no bouncing work to
do. The end result is a lot of pages set aside in bounce pools
that will never be used, and a slow path for data buffers in nearly
every DMA-capable PCIe device. For example, our workload at Netflix
was spending nearly 1% of all CPU time going through this slow path.
Fix this problem by being more selective about when to set the
COULD_BOUNCE flag. Only set it when the boundary restriction
exists and the consumer cannot do more than a single DMA segment
at once. This fixes the case of dynamic buffers (mbufs, bio's)
but doesn't address static buffers allocated from bus_dmamem_alloc().
That case will be addressed in the future.
For those interested, this was discovered thanks to Dtrace Flame
Graphs.
Discussed with: jhb, kib
Obtained from: Netflix, Inc.
MFC after: 3 days
Set the accessed and dirty bits in the page table entry. If it fails then
restart the page table walk from the beginning. This might happen if another
vcpu modifies the page tables simultaneously.
Reviewed by: alc, kib
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
on execve(2), it calls vmspace_exec(), which frees the current
vmspace. The thread executing an exec syscall gets new vmspace
assigned, and old vmspace is freed if only referenced by the current
process. The free operation includes pmap_release(), which
de-constructs the paging structures used by hardware.
If the calling process is multithreaded, other threads are suspended
in the thread_suspend_check(), and need to be unsuspended and run to
be able to exit on successfull exec. Now, since the old vmspace is
destroyed, paging structures are invalid, threads are resumed on the
non-existent pmaps (page tables), which leads to triple fault on x86.
To fix, postpone the free of old vmspace until the threads are resumed
and exited. To avoid modifications to all image activators all of
which use exec_new_vmspace(), memoize the current (old) vmspace in
kern_execve(), and notify it about the need to call vmspace_free()
with a thread-private flag TDP_EXECVMSPC.
http://bugs.debian.org/743141
Reported by: Ivo De Decker <ivo.dedecker@ugent.be> through secteam
Sponsored by: The FreeBSD Foundation
MFC after: 3 days
birthday-paradox style address collisions when
bhyve VMs are connected to the same broadcoast
domain and are using pseudo-random allocations.
Reviewed by: gnn
MFC after: 1 week
g_orphan_register and g_resize_provider_event. Both are called from the
event queue. Also we have GEOM_DEV class, which does deferred destroy
for its consumers via g_dev_destroy (also called from the event queue).
So it is possible, that for some consumers an orphan method will be
called twice. This triggers panic in g_dev_orphan.
Check that consumer isn't already orphaned before call orphan method.
MFC after: 2 weeks
Replace with the existing loop termination test with a similar
condition from the nested "if" that may terminate the loop a bit
sooner, but still not too early. This condition can then be removed
from the nested "if". Relocate an operator to be style(9) compliant.
MFC after: 3 days
to a guest physical address.
PG_PS (page size) field is valid only in a PDE or a PDPTE so it is now
checked only in non-terminal paging entries.
Ignore the upper 32-bits of the CR3 for PAE paging.
