that's ATAPI specific. Instead, skip to PROBE_SET_MULTI instead for
non ATAPI protocols. The prior code incorrectly terminated the probe
with a break, rather than arranging for probedone to get called. This
caused panics or worse on some systems.
that's only mostly similar. Specifically word 78 bits are defined for
IDENTIFY DEVICE as
5 Supports Hardware Feature Control
while a IDENTIFY PACKET DEVICE defines them as
5 Asynchronous notification supported
Therefore, only pay attention to bit 5 when we're talking to ATAPI
devices (we don't use the hardware feature control at this time).
Ignore it for ATA devices. Remove kludge that papered over this issue
for Samsung SATA SSDs, since Micron drives also have the bit set and
the error was caused by this bad interpretation of the spec (which is
quite easy to do, since bits aren't normally overlapping like this).
reduce lock congestion and improve SMP scalability of the SCSI/ATA stack,
preparing the ground for the coming next GEOM direct dispatch support.
Replace big per-SIM locks with bunch of smaller ones:
- per-LUN locks to protect device and peripheral drivers state;
- per-target locks to protect list of LUNs on target;
- per-bus locks to protect reference counting;
- per-send queue locks to protect queue of CCBs to be sent;
- per-done queue locks to protect queue of completed CCBs;
- remaining per-SIM locks now protect only HBA driver internals.
While holding LUN lock it is allowed (while not recommended for performance
reasons) to take SIM lock. The opposite acquisition order is forbidden.
All the other locks are leaf locks, that can be taken anywhere, but should
not be cascaded. Many functions, such as: xpt_action(), xpt_done(),
xpt_async(), xpt_create_path(), etc. are no longer require (but allow) SIM
lock to be held.
To keep compatibility and solve cases where SIM lock can't be dropped, all
xpt_async() calls in addition to xpt_done() calls are queued to completion
threads for async processing in clean environment without SIM lock held.
Instead of single CAM SWI thread, used for commands completion processing
before, use multiple (depending on number of CPUs) threads. Load balanced
between them using "hash" of the device B:T:L address.
HBA drivers that can drop SIM lock during completion processing and have
sufficient number of completion threads to efficiently scale to multiple
CPUs can use new function xpt_done_direct() to avoid extra context switch.
Make ahci(4) driver to use this mechanism depending on hardware setup.
Sponsored by: iXsystems, Inc.
MFC after: 2 months
Stop abusing xpt_periph in random plases that really have no periph related
to CCB, for example, bus scanning. NULL value is fine in such cases and it
is correctly logged in debug messages as "noperiph". If at some point we
need some real XPT periphs (alike to pmpX now), quite likely they will be
per-bus, and not a single global instance as xpt_periph now.
r248917, r248918, r248978, r249001, r249014, r249030:
Remove multilevel freezing mechanism, implemented to handle specifics of
the ATA/SATA error recovery, when post-reset recovery commands should be
allocated when queues are already full of payload requests. Instead of
removing frozen CCBs with specified range of priorities from the queue
to provide free openings, use simple hack, allowing explicit CCBs over-
allocation for requests with priority higher (numerically lower) then
CAM_PRIORITY_OOB threshold.
Simplify CCB allocation logic by removing SIM-level allocation queue.
After that SIM-level queue manages only CCBs execution, while allocation
logic is localized within each single device.
Suggested by: gibbs
r249017:
Some cosmetic things:
- Unify device to target insertion inside xpt_alloc_device() instead of
duplicating it three times.
- Remove extra checks for empty lists of devices and targets on release
since zero refcount check also implies it.
- Reformat code to reduce indentation.
r249103:
- Add lock assertions to every point where reference counters are modified.
- When reference counters are reaching zero, add assertions that there are
no children items left.
- Add a bit more locking to the xptpdperiphtraverse().
The device reports support for SATA Asynchronous Notification in its
IDENTIFY data, but returns error on attempt to enable that feature.
Make SATA XPT of CAM only report these errors, but not fail the device.
MFC after: 1 week
It includes three parts:
1) Modifications to CAM to detect media media changes and report them to
disk(9) layer. For modern SATA (and potentially UAS) devices it utilizes
Asynchronous Notification mechanism to receive events from hardware.
Active polling with TEST UNIT READY commands with 3 seconds period is used
for incapable hardware. After that both CD and DA drivers work the same way,
detecting two conditions: "NOT READY: Medium not present" after medium was
detected previously, and "UNIT ATTENTION: Not ready to ready change, medium
may have changed". First one reported to disk(9) as media removal, second
as media insert/change. To reliably receive second event new
AC_UNIT_ATTENTION async added to make UAs broadcasted to all periphs by
generic error handling code in cam_periph_error().
2) Modifications to GEOM core to handle media remove and change events.
Media removal handled by spoiling all consumers attached to the provider.
Media change event also schedules provider retaste after spoiling to probe
new media. New flag G_CF_ORPHAN was added to consumers to reflect that
consumer is in process of destruction. It allows retaste to create new
geom instance of the same class, while previous one is still dying.
3) Modifications to some GEOM classes: DEV -- to report media change
events to devd; VFS -- to handle spoiling same as orphan to prevent
accessing replaced media. PART class already handles spoiling alike to
orphan.
Reviewed by: silence on geom@ and scsi@
Tested by: avg
Sponsored by: iXsystems, Inc. / PC-BSD
MFC after: 2 months
reporting. It includes:
- removing of error messages controlled by bootverbose, replacing them
with more universal and informative debugging on CAM_DEBUG_INFO level,
that is now built into the kernel by default;
- more close following to the arguments submitted by caller, such as
SF_PRINT_ALWAYS, SF_QUIET_IR and SF_NO_PRINT; consumer knows better which
errors are usual/expected at this point and which are really informative;
- adding two new flags SF_NO_RECOVERY and SF_NO_RETRY to allow caller
specify how much assistance it needs at this point; previously consumers
controlled that by not calling cam_periph_error() at all, but that made
behavior inconsistent and debugging complicated;
- tuning debug messages and taken actions order to make debugging output
more readable and cause-effect relationships visible;
- making camperiphdone() (common device recovery completion handler) to
also use cam_periph_error() in most cases, instead of own dumb code;
- removing manual sense fetching code from cam_periph_error(); I was told
by number of people that it is SIM obligation to fetch sense data, so this
code is useless and only significantly complicates recovery logic;
- making ada, da and pass driver to use cam_periph_error() with new limited
recovery options to handle error recovery and debugging in common way;
as one of results, CAM_REQUEUE_REQ and other retrying statuses are now
working fine with pass driver, that caused many problems before.
- reverting r186891 by raj@ to avoid burning few seconds in tight DELAY()
loops on device probe, while device simply loads media; I think that problem
may already be fixed in other way, and even if it is not, solution must be
different.
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
until transport will do some probe actions (at least soft reset).
Make ATA/SATA SIMs to not report bogus and confusing PROTO_ATA protocol.
Make ATA/SATA transport to fill that gap by reporting protocol to SIM with
XPT_SET_TRAN_SETTINGS and patching XPT_GET_TRAN_SETTINGS results if needed.
via `camcontrol tags ... -N ...`. There is no need to tune it in
usual cases, but some users want to have it for debugging purposes.
MFC after: 2 weeks
- Add low-level support for SATA Enclosure Management Bridge (SEMB)
devices -- SATA equivalents of the SCSI SES/SAF-TE devices.
- Add some utility functions for SCSI SAF-TE devices access.
Sponsored by: iXsystems, Inc.
Even having more specific hint.ata.X.mode controls, global ones are
still could be useful from some points, including compatibility.
PR: kern/164651
MFC after: 1 week
This was previously done only for SCSI XPT in r223081, on which the change
in r223089 depended in order to respond to serial number requests. As a
result of r223089, da(4) and ada(4) devices register a d_getattr for geom to
use to obtain the information.
Reported by: ache
Reviewed by: ken
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
by timeout/error of one of probe commands, process may continue infinitely.
Make CAM ATA more robust to faulty devices and false positive detections,
abort probe after two restarts on timeouts or ten on other errors.
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
- device initiated power management (some devices support only this way);
- Automatic Partial to Slumber Transition (more power saving);
- DMA auto-activation (expected to slightly improve performance).
More features could be added later, when hardware supports.
Add Power Up In Stand-by feature support. Device with PUIS enabled
require explicit command to do initial spin-up. Mark that command
with CAM_HIGH_POWER flag, to allow CAM manage staggered spin-up.
- Unify bus reset/probe sequence. Whenever bus attached at boot or later,
CAM will automatically reset and scan it. It allows to remove duplicate
code from many drivers.
- Any bus, attached before CAM completed it's boot-time initialization,
will equally join to the process, delaying boot if needed.
- New kern.cam.boot_delay loader tunable should help controllers that
are still unable to register their buses in time (such as slow USB/
PCCard/ CardBus devices), by adding one more event to wait on boot.
- To allow synchronization between different CAM levels, concept of
requests priorities was extended. Priorities now split between several
"run levels". Device can be freezed at specified level, allowing higher
priority requests to pass. For example, no payload requests allowed,
until PMP driver enable port. ATA XPT negotiate transfer parameters,
periph driver configure caching and so on.
- Frozen requests are no more counted by request allocation scheduler.
It fixes deadlocks, when frozen low priority payload requests occupying
slots, required by higher levels to manage theit execution.
- Two last changes were holding proper ATA reinitialization and error
recovery implementation. Now it is done: SATA controllers and Port
Multipliers now implement automatic hot-plug and should correctly
recover from timeouts and bus resets.
- Improve SCSI error recovery for devices on buses without automatic sense
reporting, such as ATAPI or USB. For example, it allows CAM to wait, while
CD drive loads disk, instead of immediately return error status.
- Decapitalize diagnostic messages and make them more readable and sensible.
- Teach PMP driver to limit maximum speed on fan-out ports.
- Make boot wait for PMP scan completes, and make rescan more reliable.
- Fix pass driver, to return CCB to user level in case of error.
- Increase number of retries in cd driver, as device may return several UAs.
- Cleanup kernel messages, mostly PMP.
- Took references on devices, while PMP reinitializes them, to not let them
go and distort freeze reference counting.
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
