While at it fix an invalid memory access issue when attaching external
USB HUBs, which are not mapped by ACPI, due to missing status check
when calling AcpiGetObjectInfo() from acpi_usb_hub_port_probe_cb().
Sponsored by: Mellanox Technologies
This adds ACPI device path on devinfo(8) output and
show value of _UPC(usb port capabilities), _PLD (physical location of device)
when hw.usb.debug >= 1 .
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D20630
rename the source to gsb_crc32.c.
This is a prerequisite of unifying kernel zlib instances.
PR: 229763
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
Differential Revision: https://reviews.freebsd.org/D20193
asserted. Some development boards for example will reset on DTR,
and some radio interfaces will transmit on RTS.
This patch allows "stty -f /dev/ttyu9.init -rtsdtr" to prevent
RTS and DTR from being asserted on open(), allowing these devices
to be used without problems.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D20031
if a USB transfer is cancelled that we need to fake a completion event.
Implement missing support in ugen_fs_copy_out() to handle this.
This fixes issues with webcamd(8) and firefox.
MFC after: 3 days
Sponsored by: Mellanox Technologies
This is a curious small widget for which I might write a driver.
It is bridge between USB HID interface and I2C interface plus some
GPIO pins.
MFC after: 2 weeks
all-ones then carving out blocks of zeroes where specified values go, init
it to all-zeroes, put in ones where values need to be masked, then use it
as value &= ~sc_led_modes_mask. In addition to being more idiomatic, this
means everything related to FDT data is initialized to zero along with the
rest of the softc, and that allows removing some #ifdef FDT sections and
wrapping the whole muge_set_leds() function in a single ifdef block.
This also deletes the early-out from muge_set_leds() when an eeprom exists.
Even if there is an eeprom with led config in it, the fdt data (if present)
should override that, because the user is in control of the fdt data.
OTP registers (because the user is in control of the fdt data). Remove the
early returns from the code that tries to find a good mac address, so that
the execution always flows through the routine to get an address from FDT
data last, when on FDT-enabled systems.
the device instance, and to get the MAC address for the device instance.
The ad-hoc code this replaces could find the wrong instance if multiple
devices were present.
Also use LED mode settings from the FDT to set the PHY.
From v3 of the patch submitted in the PR.
I moved the sc_led_modes and sc_led_modes_mask default setting outside
of the #ifdef FDT case.
PR: 237325
Submitted by: Ralf <iz-rpi03@hs-karlsruhe.de>
Reviewed by: ian
MFC after: 2 weeks
MFC with: r348001
Event: Waterloo Hackathon 2019
Differential Revision: https://reviews.freebsd.org/D20325
Also apply some style(9) and remove the message about EEPROM configuration
(if there's an EEPROM the hardware handles LED configuration itself).
PR: 237325
Reviewed by: ian
MFC after: 2 weeks
Submitted by: Ralf <iz-rpi03@hs-karlsruhe.de>
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
FDT data is sometimes used to configure usb devices which are hardwired into
an embedded system. Because the devices are instantiated by the usb
enumeration process rather than by ofwbus iterating through the fdt data, it
is somewhat difficult for a usb driver to locate fdt data that belongs to
it. In the past, various ad-hoc methods have been used, which can lead to
errors such applying configuration that should apply only to a hardwired
device onto a similar device attached by the user at runtime. For example,
if the user adds an ethernet device that uses the same driver as the builtin
ethernet, both devices might end up with the same MAC address.
These changes add a new usb_fdt_get_node() helper function that a driver can
use to locate FDT data that belongs to a single unique instance of the
device. This function locates the proper FDT data using the mechanism
detailed in the standard "usb-device.txt" binding document [1].
There is also a new usb_fdt_get_mac_addr() function, used to retrieve the
mac address for a given device instance from the fdt data. It uses
usb_fdt_get_node() to locate the right node in the FDT data, and attempts to
obtain the mac-address or local-mac-address property (in that order, the
same as linux does it).
The existing if_smsc driver is modified to use the new functions, both as an
example and for testing the new functions. Rpi and rpi2 boards use this
driver and provide the mac address via the fdt data.
[1] https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/usb/usb-device.txt
Differential Revision: https://reviews.freebsd.org/D20262
Ampere eMAG systems have XHCI just described in ACPI, not on PCI.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: andrew
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D19986
RTL8152 (chip version URE_CHIP_VER_4C10) doesn't
have hardwired MAC address, in other words, it is all zeros.
This commit fixes it by setting random MAC address
when MAC address is all zeros.
Reviewed by: kevlo
Differential Revision: https://reviews.freebsd.org/D19856
Both linux and u-boot sources for RTL8152 driver has this value.
RTL8152 USB ethernet is used in NanoPI R1 board as second ethernet.
This fixes for me RTL8152 USB ethernet not detected problem after
reboot on NanoPI R1 board.
Both NetBSD and OpenBSD have a wrong value so far.
frame header and data.
This will fix 'Mysterious OLPC stuff' for received frames and wrong
CCMP / TKIP / data decoding for transmitted frames in net/wireshark
dissector.
While here, drop unneeded comment - net80211 handles padding requirements
for Tx & Rx without driver adjustment.
Tested with D-Link DWA-140 rev B3, STA mode.
MFC after: 1 week
Also, pass control frames to the host while in MONITOR mode and / or
when promiscuous mode is enabled.
Tested with Netgear WG111 v3 (RTL8187B), STA / MONITOR modes.
MFC after: 2 weeks
- Alignment issues:
* Add missing __packed attributes + padding across all drivers; in
most places there was an assumption that padding will be always
minimally suitable; in few places - e.g., in urtw(4) / rtwn(4) -
padding was just missing.
* Add __aligned(8) attribute for all Rx radiotap headers since they can
contain 64-bit TSF timestamp; it cannot appear in Tx radiotap headers, so
just drop the attribute here. Refresh ieee80211_radiotap(9) man page
accordingly.
- Since net80211 automatically updates channel frequency / flags in
ieee80211_radiotap_chan_change() drop duplicate setup for these fields
in drivers.
Tested with Netgear WG111 v3 (urtw(4)), STA mode.
MFC after: 2 weeks
Marvell XHCI is in fact generic-xhci, so move the driver and
add the compatible string.
While here, get and enable the phy if the dtb provide one.
The xhci bindings state that phys should be in a 'phys' property but
Marvell DTS uses 'usb-phy', only add support for 'usb-phy' for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
This is a "fake" phy that handle regulator, clocks and reset gpio.
Only clock and regulator is supported for now.
Sponsored-by: Rubicon Communications, LCC ("Netgate")
Enforce net80211 rates for control / management / multicast / EAPOL frames
and allow to override rate for unicast frames via ifconfig(8) 'ucastrate'
option; by default it still uses f/w rate adaptation for unicast frames.
MFC after: 1 week
Wrap ieee80211_add_channel_list_2ghz into another function
which supplies default (1-14) channel list to it and drop
its copies from drivers.
Checked with RTL8188EE, country US / JP / KR / UA.
MFC after: 2 weeks
- Check if buffer can contain Rx descriptor before accessing it.
- Verify upper / lower bounds for frame length.
- Do not pass too short frames into ieee80211_find_rxnode().
While here:
- Move cleanup to the function end.
- Reuse IEEE80211_IS_DATA() macro.
MFC after: 1 week
- Discard frames that are bigger than MCLBYTES (to prevent buffer overrun).
- Check buffer length before accessing its contents.
- Fix len <-> dmalen check - the last includes Rx Wireless information
structure size.
- Fix out-of-bounds read during Rx node search for ACK / CTS frames
(monitor mode only).
While here:
- Mark few suspicious places with comments.
- Move common cleanup to the function end.
MFC after: 1 week
Without HID_IGNORE quirk enabled these models appear in the system as a uhid
devices while NUT (Network UPS Tool) expects them to be ugen.
PR: 131521
Submitted by: Naoyuki Tai <ntai@smartfruit.com>, John Bayly <john.bayly@tipstrade.net>
MFC after: 1 week
Extend the vendor class USB audio quirk to cover devices without
the USB audio control descriptor.
PR: 234794
MFC after: 1 week
Sponsored by: Mellanox Technologies
out dead USB HUB devices by implementing an error counter, so that the USB
enumeration thread does not spend all its time reading from non-responding
devices, blocking user-space access in the end.
Tested by: Matthias Apitz <guru@unixarea.de>
MFC after: 1 week
Sponsored by: Mellanox Technologies
transaction translator will return a NAK. Ignore this message and
retry the complete split instead.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Now evdev part of keyboard drivers does not take any locks if corresponding
input/eventN device node is not opened by userland consumers.
Do not assert console lock inside evdev to handle the cases when keyboard
driver is called from some special single-threaded context like shutdown
thread.
the current fixed values, which enables use of rates above 1 Mbps.
Improved the detection of HXD chips, and the status flag handling as
well.
Submitted by: Gabor Simon <gabor.simon75@gmail.com>
PR: 225932
Differential revision: https://reviews.freebsd.org/D16639
MFC after: 1 week
Sponsored by: Mellanox Technologies
translator, when using the DWC OTG USB controller driver. Make sure to re-try
getting the complete split packets until a DATA0 packet is received. Larger
isochronous frames may be split into multiple MDATA packets terminated
by a single DATA0 packet.
PR: 230434
MFC after: 3 days
Approved by: re (gjb)
Sponsored by: Mellanox Technologies
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
r337289 has a side effect of reducing usb frame 0 buffer size down to
touch report size. That broke some devices e.g. "Raydium Touch System"
which are capable of generating non-touch frames of bigger length.
Fix it with enlarging frame 0 buffer up to internal wmt(4) buffer size.
Reported by: Roberto Fernandez Cueto <roberfern@gmail.com>
Tested by: Roberto Fernandez Cueto <roberfern@gmail.com>
Approved by: re (gjb)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16772
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Move evdev_ev_kbd_event() helper from evdev to kbd.c as otherwise evdev
unconditionally requires all keyboard and console stuff to be compiled
into the kernel. This dependency happens as evdev_ev_kbd_event() helper
references kbdsw global variable defined in kbd.c through use of
kbdd_ioctl() macro.
While here make all keyboard drivers respect evdev_rcpt_mask while setting
typematic rate and LEDs with evdev interface.
Requested by: Milan Obuch <bsd@dino.sk>
Reviewed by: hselasky, gonzo
Differential Revision: https://reviews.freebsd.org/D16614
Now softc should be retrieved from struct edvev * pointer
with evdev_get_softc() helper.
wmt(4) is a sample of driver that support both KPI.
Reviewed by: hselasky, gonzo
Differential Revision: https://reviews.freebsd.org/D16614
To compile this driver with evdev support enabled, place
following lines into the kernel configuration file:
options EVDEV_SUPPORT
device evdev
Note: Native and evdev modes are mutually exclusive.
Reviewed by: gonzo, wblock (docs)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D11156
Usbhid's hid_report_size() calculates integral size of all reports of given
kind found in the HID descriptor rather then exact size of report with given
ID as its userland counterpart does. As all input data processed by the
driver is located within the same report, calculate required driver's buffer
size with userland version, imported in one of the previous commits.
This allows us to skip zeroing of buffer on processing of each report.
While here do some minor refactoring.
MFC after: 2 weeks
if present to enable some devices like WaveShare touchscreens. Unlike
Windows we discard content of the blob. We try mimic Windows driver
behaviour from the USB device point of view.
Submitted by: glebius (initial version)
rather than from HID descriptor to match Microsoft documentation.
Fall back to HID descriptor provided value if 'Get Report' request failed.
MFC after: 2 weeks
The last known robust version of this code base was FreeBSD 8.2. There
are no users of this on current, and all users of it have abandoned
this platform or are in legacy mode with a prior version of FreeBSD.
All known users on arm@ approved this removal, and there were no
objections.
Differential Revision: https://reviews.freebsd.org/D16312
This fixes usage/report size calculation of Microsoft`s "Touch Hardware
Quality Assurance" certificate blob found in many touchscreens.
While here, join several "c->flags = dval" lines in to single line.
Reviewed by: hselasky
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16357
Remove all the big-endian arm architectures (ixp425 and ixp435)
support in the kernel and associated drivers.
Differential Revision: https://reviews.freebsd.org/D16257
Summary:
Add the device id of the Panda Wireless PAU06 which seems to be
the already-supported combination of RT5392 MAC and RF RT5372
radio.
Reviewed By: allanjude, eadler, jhb
Approved By: jhb
Differential Revision: https://reviews.freebsd.org/D16211
doing it last. Also, remove the local tracking of whether usb's busdma
memory allocation got done, because it's safe to call the free_all
function even if it wasn't.
Also replace numbered list with - bulleted so the list entries do not
need to be renumbered as tasks are completed.
Sponsored by: The FreeBSD Foundation
On FDT-enabled platforms check if DTB blob has MAC address configured by
a boot loader. This information passed as a "local-mac-address" or
"mac-address" property of the device node. For USB NICs node
can be found by looking for compatibility string "usbVVV,PPP" where
VVV - vendor id (hex) and PPP - product id (hex)
Reviewed by: emaste
Differential Revision: https://reviews.freebsd.org/D16117
lan78xx_eeprom_read just checked for EEPROM presence then called
lan78xx_eeprom_read_raw if present, and had only one caller. Introduce
lan78xx_eeprom_present to check for EEPROM presence, and use it in the
one place it is needed.
This is used by r334964, which was accidentally committed out-of-order
from my work tree.
Reported by: markj
Sponsored by: The FreeBSD Foundation
Differences between LAN7800 and LAN7850 from the driver's perspective:
* The LAN7800 muxes EEPROM signals with LEDs, so LED mode needs to be
disabled when reading/writing EEPROM. The EEPROM is not muxed on the
LAN7850.
* The Linux driver enables automatic duplex and speed detection when
there is no EEPROM, for the LAN7800 only. With this FreeBSD driver
LAN7850-based adapters without a configuration EEPROM fail to link
(with or without the automatic duplex and speed detection code), so
I have just followed the example of the Linux driver for now.
Sponsored by: The FreeBSD Foundation
Sponsored by: Microchip (hardware)
This adds several vendors from NetBSD's copy of the same file (r1.749).
Prefer longer more "canonical" names where the names differed.
Sort while here.
Add USB product ID for two GENESYS LOGIC ICs, found in DELOCK
In-Desk-Hub 61991
PR: 228489
Submitted by: "Harald Schmalzbauer" <bugzilla.freebsd@omnilan.de>
MFC After: 3 weeks
The GMII control bit ETH_MAC_CR_GMII_EN_ is not documented in
LAN78xx datasheets, but from the permissively licensed header provided
by Microchip it is:
#define ETH_MAC_CR_GMII_EN (0x00080000UL ) // GMII/RGMII Selection
is that current one (mass storage device) doesn't work as it is - it
needs to be set to 0 after the LUN is configured, which is what the
cfumass rc script does. In other words: the current default does not
work, and to actually make it work it had to be set to -1 in
/boot/loader.conf.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Previously lan78xx_chip_init locked the driver's mutex if not already
locked, but unlocked it only in the case of error. This provided a
fairly clear indication that the function is already called with the
lock held, so just replace it with a lock assertion.
Sponsored by: The FreeBSD Foundation
This driver was developed for the LAN7800 and the register-compatible
LAN7515 and has only been tested on those devices. Adding support for
other members of the family should be straightforward, once we have
devices to test.
With this change the driver will probe but fail to attach due to the
Chip ID check, but will leave a hint leading to the driver that needs
work.
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15537
This driver was developed for the LAN7800 and the register-compatible
LAN7515 (found on Raspberry Pi 3B+) and has only been tested on those
devices.
Sponsored by: The FreeBSD Foundation
This change adds support for a UBS<->RS232 adapter based on CH340 (or an
analogue) that I own. The device seems to have a newer internal version
(0x30) and the existing code incorrectly configures line control for it
resulting in garbled transmission. The changes are based on what I
learned in Linux drivers for the same hardware.
Additional changes:
- use UCHCOM_REG_LCR1 / UCHCOM_REG_LCR2 instead of explicit 0x18 and
0x25
- use NULL instead of 0 where a pointer is expected
Reviewed by: hselasky
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D15498
Also, add definitions for more bits of UCHCOM_REG_LCR1 as seen in the
Linux driver. UCHCOM_LCR1_PARENB definition was different from that in
the Linux driver and clashed with newly added UCHCOM_LCR1_RX. I took a
liberty to change UCHCOM_LCR1_PARENB to the Linux definition as it was
unused in the driver anyway. This change should make
uchcom_cfg_set_break() easier to understand.
Approved by: hselasky
MFC after: 2 weeks
Product IDs are specified in vendor documents. The previously used
device ID is not. This is a cosmetic change. No functionality depends
on those IDs.
Reviewed by: hselasky
MFC after: 2 weeks
muge was committed to the tree in r333713 but not yet connected to the
tree, and it crossed paths with the migration to using ck.
Sponsored by: The FreeBSD Foundation
Microchip provided a permissively-licensed lan78xx header, which has
an 'ETH_' prefix on most definitions. Follow suit in our driver.
Sponsored by: The FreeBSD Foundation
storage, CDC ACM (serial), and CDC ECM (ethernet) at the same time.
It's quite similar in function to Linux' "g_multi" gadget.
Reviewed by: hselasky@
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
one character too many. Note that this function is only used to decode
string descriptors generated by the kernel itself.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
This driver supports two Microchip USB-Ethernet controllers:
LAN7800 USB 3.1 to 10/100/1000 Mbps Ethernet
LAN7515 USB 2 to 10/100/1000 Mbps Ethernet with built-in USB hub
The LAN7515 is the Ethernet controller on the Raspberry Pi 3B+.
At present there is no datasheet for the LAN7515, but it is effectively
a USB 2 hub combined with a LAN7800 controller. A comprehensive LAN7800
datasheet is at http://www.microchip.com/wwwproducts/en/LAN7800.
This driver is based on the structure of the smsc(4) driver which
supports Microchip/SMSC's LAN95xx family. (Microchip acquired SMSC
in May 2012.) The Linux lan78xx driver served as a reference for some
functionality and registers.
The 'muge' driver name comes from "Microchip USB Gigabit Ethernet".
I made some style adjustments and minor edits to Arshan's submission.
It will be connected to the build after additional review and testing.
Thanks to Microchip for providing a number of Evaluation Boards (EVBs)
for development and testing.
Submitted by: Arshan Khanifar
Reviewed by: hselasky (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15168
LAN7800 USB 3.1 to 10/100/1000 Ethernet with PHY
LAN7801 USB 3.1 to 10/100/1000 Ethernet with RGMII interface
Also update manufacturer name for the Vendor ID. Microchip acquired
SMSC in May 2012.
Sponsored by: The FreeBSD Foundation
through a SYSCTL instead of a compile time define.
Add quirk by default for all LynxPoint XHCI controllers.
PR: 227602
MFC after: 3 days
Sponsored by: Mellanox Technologies
Per the datasheet, the BUSY bit must be set when reading or writing PHY
registers. From Linux commit 80928805babf.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15217
In smsc_phy_init function, when the driver was trying to reset PHY, it
didn't poll for the correct bit (BMCR_RESET) to be cleared. Instead, it
anded it with MII_BMCR (which is 0), so it just exited the loop.
This issue was fixed in Linux in commit d94609200069.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
device-side (and only device-side) "virtual USB serial adapters" - the
ones you can get with an OTG-capable board - as consoles. It boils down
to adding the device name to kern.console sysctl, although doing that
requires jumping through some hoops. It doesn't change the actual
operation of those virtual devices. The point is to make it possible
for init(8) to recognize them as console devices and to launch getty(8)
for them, when configured as "onifconsole" in ttys(5). The point of
that, in turn, is to add such entries to the default ttys(5), so that
init(8) will launch gettys for device-side "virtual serial adapters",
but not for actual USB serial dongles.
Reviewed by: hselasky@
No objections: imp@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
OF_getprop_alloc takes element size argument and returns number of
elements in the property. There are valid use cases for such behavior
but mostly API consumers pass 1 as element size to get string
properties. What API users would expect from OF_getprop_alloc is to be
a combination of malloc + OF_getprop with the same semantic of return
value. This patch modifies API signature to match these expectations.
For the valid use cases with element size != 1 and to reduce
modification scope new OF_getprop_alloc_multi function has been
introduced that behaves the same way OF_getprop_alloc behaved prior to
this patch.
Reviewed by: ian, manu
Differential Revision: https://reviews.freebsd.org/D14850
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
A series of zero delay callouts can happen causing high CPU usage of the
timer subsystem when trying to repeat keys, because the time of the
absolute timeout is not moving forward. The condition clears when all
keys are released.
Reported by: Johannes Lundberg <johalun0@gmail.com>
Discussed with: bde@
PR: 226968
MFC after: 1 week
Sponsored by: Mellanox Technologies
endpoints. The Allwinner driver will need to set this as the EPINFO
register isn't useful there.
Submitted by: jmcneill
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D5881
On the Allwinner SoCs we need to set a custom endpoint configuration. To
allow for this use a table to store the configuration so the attachment
can override it.
Reviewed by: hselasky
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14783
Move copy-pasted code for RTS/CTS frame allocation into net80211.
While here, add stat / debug message for allocation failures
(copied from run(4)) + return error here in bwn(4).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D14628
the jtag port, so that a tty is not created for it.
This is based on information in the PR and from the vendor website. When
the PR was first opened we had no facility for flagging the jtag ports. I
stumbled across the still-open PR with the idea of closing it, and noticed
that this wee update was needed.
PR: 175893
network device pointer might be NULL. Wait for any pending tasks to
complete before calling axge_stop().
MFC after: 1 week
Sponsored by: Mellanox Technologies
would be safe, but the function also tries to destroy mutexes that never
got created).
I guess this can only happen when imx_ehci_detach() is called on the
error-exit path from imx_ehci_attach(), and that path never got exercised
before today.
artificial NOMATCH usb does in lieu of creating a device_t for devices
with no drivers. Also, correct bus to be 'uhub' since where USB
devices attach, even though 'usb' is more logical, we need the
physical bus here.
Submitted by: hps@
host to reprobe the bus by switching the USB pull up resistors off and
back on. In other words - when FreeBSD is configured as a USB device,
changing the sysctl will be immediately noticed by the machine it's
connected to.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
possible to change string and numeric vendor and product identifiers,
as well as anything else there might be to change for a particular
device side template, eg the MAC address.
Reviewed by: hselasky@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13920
This removes the direct WME info access in the ieee80211com struct and instead
provides a method of fetching the data. Right now it's a no-op but eventually
it'll turn into a per-VAP method for drivers that support it (eg iwn, iwm,
upcoming ath10k work) as things like p2p support require this kind of behaviour.
Tested:
* ath(4), STA and AP mode
TODO:
* yes, this is slightly stack size-y, but it is an important first step
to get drivers migrated over to a sensible WME API. A lot of per-phy things
need to be converted to per-VAP before P2P, 11ac firmware, etc stuff shows up.
This reduces noise when kernel is compiled by newer GCC versions,
such as one used by external toolchain ports.
Reviewed by: kib, andrew(sys/arm and sys/arm64), emaste(partial), erj(partial)
Reviewed by: jhb (sys/dev/pci/* sys/kern/vfs_aio.c and sys/kern/kern_synch.c)
Differential Revision: https://reviews.freebsd.org/D10385
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
Initially, only tag files that use BSD 4-Clause "Original" license.
RelNotes: yes
Differential Revision: https://reviews.freebsd.org/D13133
Include ridx <-> rate conversion functions from rtwn(4) +
reuse already calculated value for ieee80211_radiotap(9).
Tested with Asus USB-N10, STA mode.
To accomodate all variaties of Pi DTS files floating around
we look for MAC address property either in DTS node for
USB ethernet (if it exists) or at predefined path
".../usb/hub/ethernet".
After r324184 smsc_fdt_find_eth_node started to return node
with compatibility string "usb424,ec00" as an eth node.
In imported GNU dts files this node still does not have
MAC address related property, and therefor following check for
"mac-address" and "local-mac-address" fails.
To make this logic more robust do not just search for the node
but also make sure it has required property, so if node with
accepted compatibility string exists but doesn't have the
property we fall back to looking for hardoded path mentioned above.
There should be no functional changes.
Reviewed by: hselasky
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12670
- Added more compatibility strings to drivers not yet converted
- Added new RPI platform code compatibility string to match the ones used
upstream
- Adapted RPI and RPI2 DTS to match the new platform code compatibility
string
The goal is to use the upstream DTBs as a replacement for our custom one.
This is now possible with these changes.
Additionally, as the RPI firmware automatically chooses the right DTB for
us, this would allow to have one common armv6 kernel for RPI0 and RPI1
(BCM2835-based), and one common armv7 kernel for RPI2 v1.1 (BCM2836-based),
and RPI2 v1.2 / RPI3 (BCM2837-based).
Submitted by: Sylvain Garrigues <sylgar@gmail.com>
Differential Revision: https://reviews.freebsd.org/D12360
This patch adds hwtype parameter which keeps information about hardware
revision of Marvell EHCI controller. It allows to replace multiple
calls to ofw_bus_is_compatible with comparing hwtype value during driver
initialization.
Submitted by: Patryk Duda <pdk@semihalf.com>
Suggested by: ian
Obtained from: Semihalf
Sponsored by: Semihalf
This patch reuses ehci_mv driver by adding a support for the new
compatible string and adding ehci_mv.c to list of available options
for arm64 platforms.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12255
This driver will be used by Marvell Armada 3700 and 7k/8k SoC families.
The same, generic xhci device also appears in Armada 380, so we are reusing
driver.
This patch also adds xhci_mv.c entry to the arm64 files list.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12252
It turns out that this is more than a power optization. The OTG port
won't work on boards that have this property unless this setting is honored.
Also ensure that the usb phy device attaches before ehci.
programmed for infinite IN token retry after NAK, the SAF1761
hardware, however, does not retry the IN-token. This problem is
described in the SAF1761 errata, section 18.1.1.
While at it:
- Add some minor chip specific initialization for RTEMS.
- Add debug print for status registers in the interrupt filter.
Submitted by: Christian Mauderer <christian.mauderer@embedded-brains.de>
MFC after: 1 week
A long long time ago the register keyword told the compiler to store
the corresponding variable in a CPU register, but it is not relevant
for any compiler used in the FreeBSD world today.
ANSIfy related prototypes while here.
Reviewed by: cem, jhb
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D10193
left-click event. It can be disabled setting the new
hw.usb.wsp.enable_single_tap_clicks sysctl to 0.
Submitted by: K Staring <qdk@quickdekay.net>
Pull Request: https://github.com/freebsd/freebsd/pull/97
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
This change removes limitation of single S/G list entry and limitation on
maximal I/O size, using multiple data transfers per I/O if needed. Also
it removes code duplication between send and receive paths, which are now
completely equal.
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
The tty layer uses tsw_busy to poll for busy/idle status of the transmitter
hardware during close() and tcdrain(). The ucom layer defines ULSR_TXRDY and
ULSR_TSRE bits for the line status register; when both are set, the
transmitter is idle. Not all chip drivers maintain those bits in the sc_lsr
field, and if the bits never get set the transmitter will always appear
busy, causing hangs in tcdrain().
These changes add a new sc_flag bit, UCOM_FLAG_LSRTXIDLE. When this flag is
set, ucom_busy() uses the lsr bits to return busy vs. idle state, otherwise
it always returns idle (which is effectively what happened before this
change because tsw_busy wasn't implemented).
For the uftdi chip driver, these changes stop masking out the tx idle bits
when processing the status register (because now they're useful), and it
calls ucom_use_lsr_txbits() to indicate the bits are maintained by the
driver and can be used by ucom_busy().
Differential Revision: https://reviews.freebsd.org/D9183