floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
but the present PCI probe code still thinks we are there as the pci attach
can't return an error code.
This means we are in the shared interrupt list, but have not been set up.
If we are sharing ints with another device, ohci_intr will be called and will
coredump on a NULL reference. So just return if it is called when not set up.
This fixes the symptom and not the cause.
The right answer is to let the PCI system know that the attach failed,
or to fail earlier (in the PCI probe).
The attach() is a void fn() so it can't return failure..
If we are not transfering any data, use a non S/G ccb type that doesn't
return residual information. It seems that some firmware revisions dislike
S/G ccbs with 0 length S/G lists.
Correct bt_cmd() so that we always honor command status that was latched
by our interrupt routine while polling for completion..
is more robust and common code can be used for both the target and iniator
roles. The mechanism for tracking negotiation state has also been simplified.
Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered. Make a first
stab at getting all of the bus skew delays correct. Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.
Ensure that we exit BITBUCKET mode if the controller is restarted.
Add support for target mode only firmware downloads. This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller. Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
1) Removed 'emulation' of bitmaps in printfs, FreeBSD seems to have caught
up on that one
2) Fixed a few bugs in the timeout/timo timeout variables
3) First attempt at fixing a bug mentioned by Kazu: uhci_run is not able
start/stop his USB host on his motherboard.
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
suggested compilation cleanups from Eklund. Wire down a hard loop id if we are
not on a platform that has the ability to get to a PCI BIOS (it still will
float to the ID it gets after a LIP but at least we can try). Clarify that the
expanded lun is based upon SCCLUN defines (in f/w).
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
cards. My machine didn't tickle this problem, so I can't tell if
it fixed anything or not. However, it didn't break my already working
1542-{B,C,CF,CP} probes.
o Minor comment correction
o Minor correction in printf
were half of their physical offsets for ISA and 1/4 of their physical
offsets for PCI, while all other Cyclades offsets were physical/1 for
ISA and physical/2 for PCI. Logically wrong macros were used to scale
CY16_RESET and CY_CLEAR_INTR to the correct physical offsets.
Fixed some style bugs (mostly long lines).
use a 256 entry ring buffer of descriptersfor this purpose. This allows
the use of a simple 8bit counter in the sequencer code for tracking start
location.
Entries in the ring buffer now contain a "cmd_valid" byte at their tail.
As an entry is serviced, this byte is cleared by the kernel and set by
the sequencer during its dma of a new entry. Since this byte is the last
portion of the command touched during a dma, the kernel can use this
byte to ensure the command it processes is completely valid.
The new command format requires a fixed sized DMA from the controller
to deliver which allowed for additional simplification of the sequencer
code. The hack that required 1 SCB slot to be stolen for incoming
command delivery notification is also gone.
interrupt handlers. Instead, load and use it atomically as necessary.
This reduces mode switching overhead for "polled" mode interrupt handling
from 5 i/o's to 3 (per service type, per port) so that polled mode is only
slightly more inefficient than "interrupt" mode.
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
If the next available mailbox is not in the free state, print a warning
and handle the condition as a temporary resource shortage. The condition
should never happen, but we shouldn't panic since recovery is possible.
Convert from BT'isms to AHA'isms
Don't fail the probe if the illegal command bit is set in the status
register. If the BusLogic MultiMaster probe preceeded us, it may well
have determined that the card we are attaching to was not a true MultiMaster
by sending us a command that fails on the 154X.
Reset the adapter before doing the inquiry. This provides extra sanity
and will also clear the illegal command status bit that my be left over
from the MultiMaster probe.
truncated to 32 bits.
* Change the calling convention of the device mmap entry point to
pass a vm_offset_t instead of an int for the offset allowing
devices with a larger memory map than (1<<32) to be supported
on the alpha (/dev/mem is one such).
These changes are required to allow the X server to mmap the various
I/O regions used for device port and memory access on the alpha.
base register that controls Ultra-DMA, so we need to examine all possible
base registers instead of just giving up at the first empty one.
Also, looking at the source code to the BIOS, I see that they are also
checking for 0xffffffff as an invalid value so do the same. Stefan may like
to clean this up, but at least now I can find my PCI IDE registers.
the top half to do it.
Put in a dubious check for subdisk integrity when trying to bring
up a plex where others are already up. This particular kludge is
crying out for a rewrite of the whole state code.
Add code to set_plex_state and set_volume_state to defer updates when
called from an interrupt context. This doesn't happen yet, but it
could do.
basic i/o functions, bit-banging mechanism is implemented by dev/iicbus/iicbb.c
immio.c: some bootverbose logs to watch zip+ connect/disconnect process
config_drive:
Catch an instance of anonymous drives. Doubtless many remain.
interrupt.c:
complete_rqe:
Call logrq to log iodone events if DEBUG_LASTREQS is set.
Call set_sd_state with setstate_noupdate to avoid buffered I/O out
of interrupt context.
Use define DEBUG_RESID instead of constant.
memory.c:
Remove dead expandrq() function
Malloc:
Remove directory component of file names in malloc table.
Add function vinum_rqinfo (part of the request tracing stuff).
request.c:
Add function logrq (part of the request tracing stuff).
vinumstrategy:
Check whether config needs to be written to disk, do it if so.
This is a stopgap until the Vinum daemon (bacchusd? oenologistd?)
is written.
If DEBUG_LASTREQS is set, call logrq to log user buffer headers.
launch_requests:
Correct format of debug output to console.
If DEBUG_LASTREQS is set, call logrq to log request elements.
request.h:
Add definitions for request trace.
state.c:
set_sd_state:
Check flags for setstate_noupdate. If set, don't write the config
to disk, just set global VF_DIRTYCONFIG flag. This is part of the
kludge to avoid writing config from an interrupt context.
vinumext.h:
Add declaration for vinum_rqinfo, put inside #ifdef DEBUG
Remove dead macro expandrq
vinumio.h:
Increase maximum ioctl reply length to 4 kB if DEBUG is set.
Define VINUM_RQINFO ioctl if DEBUG is set.
vinumioctl.c:
vinumioctl:
Change implementation of VINUM_DEBUG ioctl: use a debug flag
(DEBUG_REMOTEGDB) to decide whether to go into remote debugging or
not.
Implement VINUM_RQINFO.
vinumkw.h:
Define kw_info even when not debugging.
vinumvar.h:
Define VF_DIRTYCONFIG
Add pointers to request info to vinum_info if DEBUG is set.
Define setstate_noupdate
Define additional debug bits DEBUG_RESID, DEBUG_LASTREQS and
DEBUG_REMOTEGDB.
