Basically, this is automatic rx zero copy when feasible. TCP payload is
DMA'd directly into the userspace buffer described by the uio submitted
in soreceive by an application.
- Works with sockets that are being handled by the TCP offload engine
of a T4 chip (you need t4_tom.ko module loaded after cxgbe, and an
"ifconfig +toe" on the cxgbe interface).
- Does not require any modification to the application.
- Not enabled by default. Use hw.t4nex.<X>.toe.ddp="1" to enable it.
- Setup multiple DDP page sizes. When the driver attempts DDP it will
try to combine physically contiguous pages into regions of these sizes.
- Set the indicate size such that the payload carried in the indicate can
be copied in the header mbuf (and the 16K rx buffer can be recycled).
- Set DDP threshold to the max payload that the chip will coalesce and
deliver to the driver (this is ~16K by default, which is also why the
offload rx queue is backed by 16K buffers). If the chip is able to
coalesce up to the max it's allowed to, it's a good sign that the peer
is transmitting in bulk without any TCP PSH.
MFC after: 2 weeks
TCB. Filters are programmed by modifying the TCB too (via a different
routine) and the reply to any TCB update is delivered via a
CPL_SET_TCB_RPL. Figure out whether the reply is for a filter-write or
something else and route it appropriately.
MFC after: 2 weeks
makes calls out to the emulator, the locking is fairly simple. A global
mutex protects the list of ssc disks, and each ssc disk has a mutex
to protect it's bioq.
Approved by: marcel
tick until the situation is resolved (if ever), just print a single
message when running out and another when space becomes available.
- When adding more swap, warn if the total amount exceeds half the
theoretical maximum we can handle.
Add timeout to wait for network controllers to appear when netbooting.
USB ethernet adapter initialization usually is delayed and
they're not available immidiately after autoconfiguration. So we need
to wait a bit before giving up
Reviewed by: stas@
to this pmap.
Tidy up the #include's.
Remove the (now) unused #define PMAP_SHPGPERPROC. (This should have
been removed in r239236.)
Tested by: jchandra
iterate lock.
This causes LORs and deadlocks as some code paths will have the com lock
held when calling ieee80211_iterate_nodes().
Here, the comlock isn't held during the node table and node iteration
locks; and the callback isn't called with any (extra) lock held.
PR: kern/170098
Submitted by: moonlightakkiy@yahoo.ca
MFC after: 4 weeks
"m_getjcl:invalid cluster type" that occurred some
time back with the igb driver. This happens often when
booting over the net. I believe the NIC hardware is left
in a warm state when handed over to the driver, and a stray
RX interrupt happens earlier than the code is prepared for
it to happen. This change was verified to fix the problem,
its kind of a bandaid... but it is similar to what was done
in the igb code.
1) It is not useful to call "devfs_clear_cdevpriv()" from
"d_close" callbacks, hence for example read, write, ioctl and
so on might be sleeping at the time of "d_close" being called
and then then freed private data can still be accessed.
Examples: dtrace, linux_compat, ksyms (all fixed by this patch)
2) In sys/dev/drm* there are some cases in which memory will
be freed twice, if open fails, first by code in the open
routine, secondly by the cdevpriv destructor. Move registration
of the cdevpriv to the end of the drm open routines.
3) devfs_clear_cdevpriv() is not called if the "d_open" callback
registered cdevpriv data and the "d_open" callback function
returned an error. Fix this.
Discussed with: phk
MFC after: 2 weeks
"device_free_softc()" and "device_claim_softc()",
to allow USB serial drivers refcounting the softc.
These functions are used to grab the softc from
auto-free and to free the softc back to the correct
malloc type, respectivly.
Discussed with: jhb
MFC after: 2 weeks
* the descriptor ID, and
* the multi-buffer support that the EDMA chips support.
This is required for successful MAC transmission of multi-descriptor
frames. The MAC simply hangs if there are NULL buffers + 0 length pointers,
but the descriptor did have TxMore set.
This won't be done for the 11n aggregate path, as that will be modified
to use the newer API (ie, ath_hal_filltxdesc() and then set first|middle|
last_aggr), which will deprecate some of the current code.
TODO:
* Populate the numTxMaps field in the HAL, then make sure that's fetched
by the driver. Then I can undo that hack.
Tested:
* AR9380, AP mode, TX'ing non-aggregate 802.11n frames;
* AR9280, STA/AP mode, doing aggregate and non-aggregate traffic.
