If platform support EXT_RESOURCES, clocks and resets are handled out of
the box.
If not driver can be subclassed using the generic_usb interface.
generic_usb name was choosed because at one point I'll add generic-ehci
FDT driver.
Reviewed by: jmcneill, hselasky
Approved by: andrew (mentor)
Differential Revision: https://reviews.freebsd.org/D5481
The A83T thermal sensor controller has three sensors. Sensor 0 corresponds
to CPU cluster 0, sensor 1 to CPU cluster 1, and sensor 2 to the GPU. This
driver exports the temperature sensor readings via sysctl.
Calibration data is obtained from SRAM found in the Secure ID module.
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D6378
Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
The datasheets refer to this controller as EMAC, not to be confused with
the fast ethernet controller (also named EMAC) found in A10/A20 SoCs.
Tested on a BananaPi M3 (A83T), which uses an external RGMII PHY (RTL8211E).
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6169
The HDMI driver will attach a framebuffer device when a display is
connected. If the EDID can be read and contains a preferred mode, it
will be used. Otherwise the framebuffer will default to 800x600.
In addition, if the EDID contains a CEA-861 extension block and the
"basic audio" flag is set, audio playback at 48kHz 16-bit stereo is
enabled on the controller.
Reviewed by: andrew
Approved by: gonzo (mentor)
Differential Revision: https://reviews.freebsd.org/D5383
driver. This mostly involves selecting the register offsets to use at
runtime based on the hardware we are talking to.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D5327
A10/A20 SoC. Based loosely on the submitters NetBSD driver, tested on
Cubieboard 2. Playback and capture are supported.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5202
least the audio codec driver currently in review.
Submitted by: Jared McNeill <jmcneill@invisible.ca>
Differential Revision: https://reviews.freebsd.org/D5050
with this and an Allwinner SoC to power off.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4954
Marvell twsi part, however uses different register locations, as such split
the existing driver into Marvell and Allwinner attachments.
While here clean a few style issues.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4846
* Use the Linux compat string
* Use EARLY_DRIVER_MODULE to attach at the right time
* Add a generic A10 kernel config file
* A20 now use generic_timer
* Add two new dts files for Olimex boards
* Update our custom DTS file for A10 and A20 to use the same compatible
property names as the vendor ones.
Submitted by: Emmanuel Vadot <manu@bidouilliste.com>
Differential Revision: https://reviews.freebsd.org/D4792
* Use the ARM PLATFORM framework
* Use ARM_INTRNG on teh A20 as it has a GICv2
* Add a method to find which Allwinner SoC we are running on
Differential Revision: https://reviews.freebsd.org/D5059
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
This is based on the patch sent by Alexander Fedorov with the following
fixes/improvements:
- Better error handling;
- Clock is derived from PLL6 (obtained from netbsd);
- No more unnecessary busy loops on interrupt handler;
- style(9) fixes and code cleanup.
I also want to thanks Martin Galvan who has sent an alternative
implementation with some interesting fixes.
Tested on CubieBoard2, Banana-Pi (thanks to netgate!) and Cubieboard1
(Pratik Singhal).
This is intended to pave the way for the upcoming GSoC work (and make
easier the build of images for the supported boards).
PR: 196081
Submitted by: Alexander Fedorov <alexander.fedorov@rtlservice.com>
