The audio controller in the H3 is more or less the same as A10/A20 except
some registers are shuffled around. The mixer interface, however, is
completely different between SoCs. Separate a10_mixer_class and
h3_mixer_class implementations are now made available. This will also make
adding support for other SoCs easier in the future.
Reviewed by: andrew, ganbold
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8425
* Rename ARM_HAVE_MP_EXTENSIONS to ARM_USE_MP_EXTENSIONS and extend it to
handle more cases, including when SMP is not enabled.
* Check ARM_USE_MP_EXTENSIONS when building for ARMv7+, even if no SMP.
* Use ARM_USE_MP_EXTENSIONS in pmap-v6.c to detect when to set PRRR_NS1.
With this we should be able to boot on all ARMv7+ Cortex-A cores with
32-bit support.
Reviewed by: mmel, imp (earlier version)
Relnotes: yes
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8335
PLL1 is used by the cpu core, allowing changing freq is needed for cpufreq.
The factors table contains all the frequencies in the operating point table
present in the DTS.
MFC after: 1 week
hardware that supports the mp extensions. If so it should use the broadcast
tlb invalidate instructions as other CPUs or devices may need to know about
the invalidation.
To simplify the code have the compiler optimise out the else case when not
builing for Cortex-A8.
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D8092
Push-Pull Two Wire interface is a almost compatible iic like bus used
in sun6i SoC. It's only use is to communicate with the power management IC.
Reviewed by: jmcneill
MFC after: 1 week
Relnotes: yes
prevent overheating.
When sensor 0's alarm interrupt is fired, set a throttle flag. Further
requests to set CPU frequency will be rejected until sensor 0's temperature
returns to a level below the hot temperature threshold.
Relnotes: yes
The exported functions will be used by
Alpine Ethernet driver.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: wma
Differential Revision: https://reviews.freebsd.org/D7763
This patch adds support for MSI-X interrupts
on Annapurna Alpine platform. MSI-X on Alpine
work similarly to GICv2m, i.e. some range of
SPI interrupts is reserved in GIC and individual
SPIs can be triggered by MSI-X messages.
This SPI range is defined in FDT.
Obtained from: Semihalf
Submitted by: Michal Stanek <mst@semihalf.com>
Sponsored by: Annapurna Labs
Reviewed by: nwhitehorn, wma
Differential Revision: https://reviews.freebsd.org/D7579
When detaching device trees parent devices must be detached prior to
detaching its children. This is because parent devices can have
pointers to the child devices in their softcs which are not
invalidated by device_delete_child(). This can cause use after free
issues and panic().
Device drivers implementing trees, must ensure its detach function
detaches or deletes all its children before returning.
While at it remove now redundant device_detach() calls before
device_delete_child() and device_delete_children(), mostly in
the USB controller drivers.
Tested by: Jan Henrik Sylvester <me@janh.de>
Reviewed by: jhb
Differential Revision: https://reviews.freebsd.org/D8070
MFC after: 2 weeks
- Rename SOC_BCM2837 to SOC_BRCM_BCM2837, put it to opt_soc.h
- do not use files.XXX files, just move required sources to
conf/files.arm64 and make them depend on soc_brcm_bcm2837
Suggested by: andrew
Using the device pager with /dev/kmem is not stable since KVA mappings
are transient, but the device pager caches the PA associated with a
given offset forever. Interestingly, mips' implementation of
memmap() already refused requests for /dev/kmem.
Note that kvm_read/kvm_write do not use mmap, but use read and write on
/dev/kmem, so this should not affect libkvm users.
Reviewed by: kib
MFC after: 2 months
RPI3 kernel config builds kernel compatible with latest upstream device
tree and firmware: https://github.com/raspberrypi/firmware/tree/master/boot
As of today it's 597c662a613df1144a6bc43e5f4505d83bd748ca
Default console is PL01x, so pi3-disable-bt dt overlay should be configured
in config.txt and stock U-Boot should be patched to use proper serial port.
Yet unsupported: SMP, VCHIQ, RNG driver. RNG requires some work due to
upstream device tree incompatibility.
Multiple people contributed to this work over time: db@, loos@, manu@
