- Don't try to set typematic rate if there is not a keyboard.
- Fix wrong test on error code.
- Don't try to claim the keyboard twice. The second call will fail.
keyboard and video card drivers.
Because of the changes, you are required to update your kernel
configuration file now!
The files in sys/dev/syscons are still i386-specific (but less so than
before), and won't compile for alpha and PC98 yet.
syscons still directly accesses the video card registers here and
there; this will be rectified in the later stages.
+ ECP parallel port chipset FIFO detection
+ DMA+FIFO parallel I/O handled as chipset specific
+ nlpt updated in order to use the above enhanced parallel I/O.
Use 'lptcontrol -e' to use enhanced I/O
+ Various options documented in LINT
+ Full IEEE1284 NIBBLE and BYTE modes support. See ppbus(4) for
an overview of the IEEE1284 standard
+ Detection of PnP parallel devices at boot
+ Read capability added to nlpt driver to get IEEE1284 compliant
printer status with a simple 'cat /dev/lpt0'
+ IEEE1284 peripheral emulation added to BYTE mode. Two computers
may dialog according to IEEE1284 signaling method.
See PERIPH_1284 option and /sys/dev/ppbus/ppi.c
All this code is supposed to provide basic functions for IEEE1284 programming.
ppi.c and nlpt.c may act as examples.
It was nay'ed before committing on the grounds that this is not
the way to do it, and has been decided as such several times in
the past.
There is not point in loading gobs of ascii into the kernel when
the only use of that ascii is presentation to the user.
Next thing we'd be adding all section 4 man pages to the loaded
kernel as well.
The argument about KLD's is bogus, klds can store a file in
/usr/share/doc/sysctl/dev/foo/thisvar.txt with a description and
sysctl or other facilities can pick it up there.
Proper documentation will take several K worth of text for many
sysctl variables, we don't want that in the kernel under any
circumstances.
I will welcome any well thought out attempt at improving the
situation wrt. sysctl documentation, but this wasn't it.
than ".so". The old extension conflicted with well-established
naming conventions for dynamically loadable modules.
The "clean" targets continue to remove ".so" files too, to deal with
old systems.
was tested for month or two in production).
Noticed by: Stephen McKay
Stephen also suggested to remove the complication at all. I don't do it as
it would be backout of a large part of 1.190 (from 1998/03/16)...
on the ASIX AX88140A chip. Update /sys/conf/files, RELNOTES.TXT,
/sys/i388/i386/userconfig.c, sysinstall/devices.c, GENERIC and LINT
accordingly.
For now, the only board that I know of that uses this chip is the
Alfa Inc. GFC2204. (Its predecessor, the GFC2202, was a DEC tulip card.)
Thanks again to Ulf for obtaining the board for me. If anyone runs
across another, please feel free to update the man page and/or the
release notes. (The same applies for the other drivers.)
FreeBSD should now have support for all of the DEC tulip workalike
chipsets currently on the market (Macronix, Lite-On, Winbond, ASIX).
And unless I'm mistaken, it should also have support for all PCI fast
ethernet chipsets in general (except maybe the SMC FEAST chip, which
nobody seems to ever use, including SMC). Now if only we could convince
3Com, Intel or whoever to cough up some documentation for gigabit
ethernet hardware.
Also updated RELNOTEX.TXT to mention that the SVEC PN102TX is supported
by the Macronix driver (assuming you actually have an SVEC PN102TX with
a Macronix chip on it; I tried to order a PN102TX once and got a box
labeled 'Hawking Technology PN102TX' that had a VIA Rhine board inside
it).
devices dynamically. That means,
+ only one /dev/iic or /dev/smb device for each smb/iic bus to access
+ I2C/SMB device address must be given to any ioctl
+ new devices may be plugged and accessed after boot, which was
impossible previously (device addresses were hardcoded into
the kernel)
version and the asm version are inlined, and everything is cached,
the asm version is 1.75 times slower than the C version on P5's.
On K6's, it is only 1.25 times slower.
fixing it. See rev.1.22 of ../sound/audio.c for fixes. When both
the C version and the asm version are inlined, and everything is cached,
the asm version is 1.75 times slower than the C version on P5's. On
K6's, it is only 1.25 times slower.
versions of gcc and broken for current versions of egcs. The asm
here (for translate_bytes()) is now an interesting example of one
that needs to be volatile to work.
Fixed missing "memory" in the clobber list for translate_bytes().
Submitted by: "John S. Dyson" <dyson@iquest.net> but rewritten by me
versions of gcc and broken for current versions of egcs.
Cleaned up the asm statement for do_cpuid() a little.
Submitted by: "John S. Dyson" <dyson@iquest.net> but rewritten by me
RB_CONFIG.
Now, the code should do the right thing in the following cases, when
kernel is compiled with INTRO_USERCONFIG:
* when booted without userconfig_script and without RB_CONFIG, present
intro screen, and wait for user input.
* when booted with userconfig_script and without RB_CONFIG, DON'T present
intro screen unless explicitly asked in userconfig_script, basing on
assumption that if a user loads userconfig_script, (s)he already
decided what parameters to configure. Proceed with booting.
* when booted without userconfig_script, and with RB_CONFIG, enter
configuration utility and wait for user input.
* when booted with userconfig_script, and with RB_CONFIG, execute all
commands from userconfig_script, and DON'T leave the config utility,
but wait for user input.
And finally, regardless of the combination of the above parameters,
when intro screen is invoked either first or next times, and user
chooses to go back to CLI interface, unblock the quit command.
On a system with a large amount of ram (e.g. 2G), allocation of per-page
data structures (512K physical pages) could easily bust the initial kernel
page table (36M), and growth of kernel page table requires kptobj.
from sc, vt and sio drivers. Use instead a linker_set to collect them.
Staticize ??cngetc(), ??cnputc(), etc functions in sc and vt drivers.
We must still have siocngetc() and siocnputc() as globals because they
are directly referred to by i386-gdbstub.c :-(
Oked by: bde
already loaded and interpreted userconfig_script. Otherwise, when using
such kernel system would always block waiting for user input in UserConfig,
while the intention was to avoid this by having userconfig_script.
Reviewed by: msmith
that they might be about to blow their feet off if they have not been
reading their mail. I don't know if or how well this will work, but it's
worth a try.
downward growing stacks more general.
Add (but don't activate) code to use the new stack facility
when running threads, (specifically the linux threads support).
This allows people to use both linux compiled linuxthreads, and also the
native FreeBSD linux-threads port.
The code is conditional on VM_STACK. Not using this will
produce the old heavily tested system.
Submitted by: Richard Seaman <dick@tar.com>
list of devices which has been changed in UserConfig, without resorting
to reading /dev/kmem.
The data returned consist of series of struct isa_device and
char dev_name[8].
Ok'd by: jkh
- Special registers of IO-DATA device's RSA series are defined in
ic/rsa.h (new file).
Pointed out by: Bruce Evans <bde@zeta.org.au>
Submitted by: Takahashi Yoshihiro <nyan@wyvern.cc.kogakuin.ac.jp>
used in device attach routines. At least for attaches at boot time,
actually waiting, or actually failing for malloc(..., M_NOWAIT), are
almost equally unlikely and harmless, but using M_WAITOK interferes
with automatic detection of bogus M_WAITOK's.
deltas, but it is possible since I had a few merge conflicts over the last
few days while this has been sitting ready to go.
(Part 1 was committed to the config files, but cvs aborted grrr..)
Approved by: core
default for BINDIR. The default BINDIR of /usr/mdec can't be overridden
yet because libdisk still uses /usr/mdec and installing in /boot might
clobber the new boot blocks.
Don't install links to bootxx or xxboot.
Install boot1 and boot2 in 1 step.
Don't delete the boot.help source file on installing it when ${COPY} is
null.
There's something that's been bugging me for a while, so I decided to fix it.
FreeBSD now will DTRT WRT DDB and DDB_UNATTENDED (!debugger_on_panic), at least
in my opinion. The behavior change is such that:
1. Nothing changes when debugger_on_panic != 0.
2. When DDB_UNATTENDED (!debugger_on_panic), if a panic occurs, the
machine will reboot. Also, if a trap occurs, the machine will
panic and reboot, unlike how it broke to DDB before. HOWEVER,
a trap inside DDB will not cause a panic, allowing full use
of DDB without having to worry about the machine being stuck
at a DDB prompt if something goes wrong during the day.
Patches for this behavior follow my signature, and it would
be a boon to anyone (like me) who uses DDB_UNATTENDED, but
actually wants the machine to panic on a trap (otherwise,
what's the use, if the machine causes a fatal trap rather than
a true panic, of debugger_on_panic?). The changes cause no
adverse behavior, but do involve two symbols becoming global
Submitted by: Brian Feldman <green@unixhelp.org>
CPU_WT_ALLOC does not work correctly for K6-2s of model 8+ and
probably K6-3s (when they appear on the market soon). In addition,
print_AMD_info() incorrectly printfs write allocation's size. I've
fixed them, so they now Do The Right Thing, and added a
"NO_MEMORY_HOLE" option to easily allow 15-16mb range handling for us
K6 and K6-2 users.
Submitted by: Brian Feldman <green@unixhelp.org>
ISDN4BSD is the work of our brand-new comitter: Hellmuth Michaelis,
who has done a tremendous amount of work to bring us this far.
There are still some outstanding issues and files to bring into
the tree, and for now it will be needed to pick up all the extra
docs from the isdn4bsd release.
It is probably also a very good idea to subscribe to the isdn@freebsd.org
mailing list before you try this out.
These files correspond to release "beta Version 0.70.00 / December
1998" from Hellmuth.
"I've been having a problem running the patches [committed to current]
installed with the COMPAT_LINUX_THREADS option along
with the VM_STACK patches I did. I'm not sure what
the problem is, since it seemed to work before.
In any event, the attached patch fixes the problem for
me. While I've had no report of problems from anyone
else, possibly it would be wise to commit the patch
until the problem is found.
Also, there was some left-over junk in the linux_misc.c
file from some earlier work I did. The attached patch
cleans that up too."
Submitted by: "Richard Seaman, Jr." <dick@tar.com>
in cyopen() were done in a different order than in sioopen(), partly
to (ab)use a side effect of comparam() and partly because I didn't
understand what the reset was doing (it flushes the fifos). This
turned out to be more than a cosmetic problem. Flushing the fifos
quite late is good for discarding input that arrived while the line
state was being initialized, and in the cy driver it also seems to
reduce a problem with input that arrived long ago during the previous
close (the UART loses sync too easily and for too long).
change the original code but add an extra option "ALI_V" to check the
precise IDE port.(especially, secondary) Use the same option "ALI_V" on
the kernel config file to prevent generic DMA check causes wrong result.
(It seems buggy even on PIIX4 chipset, and I don't know when this bug start)
Should I add the option "ALI_V" into /sys/i386/conf/LINT ?
performed all sorts of sanity checks. The FreeBSD linux emulator returns
EINVAL in such a case.
Allowing signal 0 to be passed to kill will result in compatible behaviour.
PR: 9082
Submitted by: Marcel Moolenaar <marcel@scc.nl>
ethernet driver.
The BUGS section is still impressive, but the driver seems to work for
me now. Disclaimer: i haven't been able to test this under -current
so far (but it compiles, and the notebook it's intended for can now be
updated to -current more easy than before). Don't be afraid of the
many #ifdefs on __FreeBSD_version in the imported file; i want them in
the repository on the vendor-branch so other people can also manually
integrate it into older systems. I'll clean it up on the -current
branch in a followup commit. The vendor-banch version right now
supports systems back to 2.2R.
This driver should be layered upon ppc(4), but i currently have no
idea how to do this.
Eventually i'll further develop the driver to also support the more
modern RTL 8012 success, which seems to be present in a number of
cheap pocket ethernet adapters these days. Right now, i doubt it will
run with the 8012 without any changes.
Finally a big Thanks! to RealTek for promptly providing me with
documentation and with the source code for the 8012 pocket driver upon
request. I wish all vendors were that cooperative!.
linker sets don't work and thus neither does the kernel.
This should stop being a problem with an improved linker set mechanism in
the pipeline (see the bootloader) but for now this has to stay like this.
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
Submitted by: "Richard Seaman, Jr." <lists@tar.com>
Obtained from: linux :-)
Code to allow Linux Threads to run under FreeBSD.
By default not enabled
This code is dependent on the conditional
COMPAT_LINUX_THREADS (suggested by Garret)
This is not yet a 'real' option but will be within some number of hours.
- created internal names for fixed-size integral types, like __int32_t. They
will be used to make several headers self-sufficient.
- <stdlib.h> don't include <machine/types.h> anymore.
- created <sys/inttypes.h>, which can be used as <inttypes.h>.
- declaration of uoff_t and ufs_daddr_t moved to <sys/types.h>.
Reviewed by: bde
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
Not tested on the if_sr, if_cx and if_ar drivers, but
expected to work just the same as it used to.
Any users of these drivers (or even better: donors
of hardware for them) please contact phk@freebsd.org
so we can test the next batch of changes to if_sppp.
adjusted related casts to match (only in the kernel in this commit).
The pointer was only wanted in one place in kern_exec.c. Applications
should use the kern.ps_strings sysctl instead of PS_STRINGS, so they
shouldn't notice this change.
as well as several functional additions.
(1) dot3 MIB support.
(2) if_media selection method support.
(3) bridge support.
(4) new boards support. Supported boards are as follows.
[PC/AT]
* Fujitsu FMV-180 series
* Allied-Telesis RE2000 series
* Allied-Telesyn AT1700 series
* Gateway Communications G/Ether series
* UB networks Access/PC ISA series
* TDK/LANX LAC-AX series
* ICL EtherTeam16i series
* RATOC REX-5586/5587
[PC-98]
* Allied-Telesis RE1000 series
* Allied-Telesis RE1000Plus/ME1500 series
* Contec C-NET(9N)E series
* Contec C-NET(98)P2 series
* UB networks Access/PC N98C+ series
* TDK/LANX LAC-98 series(not tested)
Submitted by: seki@sysrap.cs.fujitsu.co.jp (Masahiro Sekiguchi) and
chi@bd.mbn.or.jp (Chiharu Shibata)
in rev.1.30 (just before FreeBSD-1.1R) to almost match corresponding
breakage in FreeBSD-1.x's diskerr(). FreeBSD-2.x's diskerr() never
had the breakage.
bug, but set it to 0 anyway to get rid of warning.
Get rid of uninitialized warning for local variable 'line' as well as
make a minor change to its scope. Again, no bug.
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
programs using glibc expect edx to be preserved accross syscalls.
As a result, linux programs running in emulation mode can
have whatever value may be represented by edx clobbered.
PR: 9038
Submitted-By: Richard Seaman, Jr. <dick@tar.com>
that the generated files are generated before any of the object files.
Also minor cleanup of dependencies in conf/files that I bogusly added
before.
This should fix the requirement that make depend be done starting from
a clean config directory. If you don't have a clean directory, make
depend is still required if you want the proper .o's to be recompiled.
Reviewed by: bde
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
problem is worked around by using an interrupt gate for the page
fault handler. This code was originally made for NetBSD/pc98 by
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp> and has already
been in PC98 tree. Because of this bug, trap_fatal cannot show
correct page fault address if %cr2 is obtained in this function.
Therefore, trap_fatal uses the value from trap() function.
- The trap handler always enables interruption when buggy application
or kernel code has disabled interrupts and then trapped. This code
was prepared by Bruce Evans <bde@FreeBSD.org>.
Submitted by: Bruce Evans <bde@FreeBSD.org>
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp>
going to want a major number from that list instead. Also use the
same preallocated local range (500-600) for blkdevs as well as cdevs,
just to be orthogonal. The latter was for Brian, who has a *lot*
of local device drivers and needs more than just a single reserved
number.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
install all those images at all (nor to install them under /usr/mdec), given
the high degree of customization this Makefile needs in order to get images
that are actually useful for some NIC.
Submitted by: John Hay <jhay@mikom.csir.co.za>,
Paul Allenby <pallenby@mikom.csir.co.za>
