The 5ghz hostap mode (where DFS is being done) requires ANI to be disabled
or the radar detection parameters don't work as advertised (as they're based
on signal strength level, and tweaking ANI affects the signal strangth,
dynamic range and power increase the baseband is looking for in order to
detect it as a "signal".)
Obtained from: Linux, Atheros
Sponsored by: Hobnob, Inc.
* If we fall through from an ANI command (eg because it's out of range,
or it's disabled) then fall through to the next ANI command rather then
being stuck there.
* Fix some off-by-one comparisons, meaning the final level in some parameters
were never tweaked.
Obtained from: Atheros
Sponsored by: Hobnob, Inc.
This forces a full reset of the baseband/radio and seems needed to clear
some issues (with Merlin at least) when the baseband gets confused in a
very noisy environment.
Sponsored by: Hobnob, Inc.
RX clear, RX extension clear.
This is useful for estimating channel business.
The same routines should be written for AR5210->AR5212 where appopriate.
Obtained from: Atheros
some unmerged interrupt status debugging code from my branch.
* Add ah_intrstate[8] which will have the record of the last
call to ath_hal_getintr().
* Wrap the KTR code behind ATH_KTR_INTR_DEBUG.
* Add the HAL interrupt debugging behind AH_INTERRUPT_DEBUGGING.
This is only done for the AR5416 and later NICs but it will be
trivial to add to the earlier NICs if required.
Neither are enabled by default, although to minimise HAL binary
API differences, the ah_intrstate[] array is always compiled into
the ath_hal struct.
* preserve AR_TxIntrReq on every descriptor in an aggregate chain,
not just the first descriptor;
* always blank out the descriptor in ar5416ChainTxDesc() when forming
aggregates - the way I'm using this in the 11n branch is to first
chain aggregates together, then use the other HAL calls to fill in
the details.
* Add the TID field in the TX status descriptor;
* Add in the 11n first/middle/last functions for fiddling
with the descriptors. These are from the Linux and the
reference driver, but I'm not (currently) using them.
* Add further AR_ISR_S5 register definitions.
Obtained from: Linux ath9k, Atheros
interfere with traffic, as the NF load can take quite a while and poking the
AGC every 10uS is just a bit silly.
Instead, just leave the baseband NF calibration where it is and just read it
back next time a longcal interval happens.
The AR5008/AR9001 series NICs have a bug where BB register reads
will occasionally be corrupted. This could cause issues with things
such as ANI, which adjust operational parameters based on the
BB radio register reads. This was introduced in the AR5008 chip
and fixed with the first released AR9002 series NIC (AR9280v2.)
A followup commit will implement the acutal WAR when reading
BB registers. I'm still not sure how I'll implement it - whether
it should be done in the osdep layer, or whether it should just
live in the AR5416 HAL. Either way, they can use this capability
bit to determine whether to implement the WAR or not.
Thankyou to various sources inside Atheros who have helped me track
down what this particular issue is.
Obtained from: Atheros
Pre-11n devices and AR5416 use AR_PHY(263) for current RX RSSI.
AR9130 and later have a fourth calibration register (for doing
ADC calibration) and thus the register has moved to AR_PHY(271).
This isn't currently used by any of the active code; I'm committing
this for completeness and in case any third party code attempts to
use it for legacy reasons.
* The AR_ISR_RAC interrupt processing method has a subtle bug in all
the MAC revisions (including pre-11n NICs) until AR9300v2.
If you're unlucky, the clear phase clears an update to one of the
secondary registers, which includes TX status.
This shows up as a "watchdog timeout" if you're doing very low levels
of TX traffic. If you're doing a lot of non-11n TX traffic, you'll
end up receiving a TX interrupt from some later traffic anyway.
But when TX'ing 11n aggregation session traffic (which -HEAD isn't yet
doing), you may find that you're only able to TX one frame (due to
BAW restrictions) and this may end up hitting this race condition.
The only solution is to not use RAC and instead use AR_ISR and the
AR_ISR_Sx registers. The bit in AR_ISR which represents the secondary
registers are not cleared; only the AR_ISR_Sx bits are. This way
any updates which occur between the read and subsequent write will
stay asserted and (correctly) trigger a subsequent interrupt.
I've tested this on the AR5416, AR9160, AR9280. I will soon test
the AR9285 and AR9287.
* The AR_ISR TX and RX bits (and all others!) are set regardless of
whether the contents of the AR_IMR register. So if RX mitigation is
enabled, RXOK is going to be set in AR_ISR and it would normally set
HAL_INT_RX.
Fix the code to not set HAL_INT_RX when RXOK is set and RX mitigation
is compiled in. That way the RX path isn't prematurely called.
I would see:
* An interrupt would come in (eg a beacon, or TX completion) where
RXOK was set but RXINTM/RXMINT wasn't;
* ath_rx_proc() be called - completing RX frames;
* RXINTM/RXMINT would then fire;
* ath_rx_proc() would then be called again but find no frames in the
queue.
This fixes the RX mitigation behaviour to not overly call ath_rx_proc().
* Start to flesh out more correct timer interrupt handling - it isn't
kite/merlin specific. It's actually based on whether autosleep support
is enabled or not.
This is sourced from my 11n TX branch and has been tested for a few weeks.
Finally, the interrupt handling change should likely be implemented
for AR5210, AR5211 and AR5212.
There are some timing concerns which I've yet to fully map out.
In any case, there's an existing software driven mitigation method
for TX interrupts and when TX'ing 11n frames, the whole frame itself
generates an interrupt rather then the subframes.
Although I tried to fix this earlier by introducing HALDEBUG_G(), it
turns out there seem to be other cases where the pointer value is still
NULL.
* Fix DO_HALDEBUG() and the HALDEBUG macro to check whether ah is NULL
before deferencing it
* Remove HALDEBUG_G() as it's no longer needed
This is hopefully a merge candidate for 9.0-RELEASE as enabling
debugging at startup could result in a kernel panic.
rather than the whole beacon interval.
The reference driver and Linux ath9k both choose 80% of the
beacon interval and they do it in the driver rather than
the HAL (Ath reference) or ath9k_hw (ath9k.)
This quietens stuck beacon conditions on my AR9220/AR9280
based NICs when a lot of burst broadcast/multicast traffic
is going on. It doesn't seem to annoy the earlier MACs as
much as the AR9280 and later one.
Obtained from: Linux ath9k, Atheros
local variable with a beacon interval of 100 TU. This never gets modified
if the beacon interval configuration changes.
This may have been correct in earlier times, but with the advent of
staggered beacons (which default to 1 / ATH_BCBUF beacon interval, so
25 TU here) this value is incorrect.
It is used to configure the default CABQ readytime. So here, the cabq
was being configured to be much greater than the target beacon timer
(TBTT.)
The driver should be configuring a cabq readytime value rather then
leaving it to the HAL to choose sensible defaults. This should be
done in the future - I'm simply trying to ensure sensible defaults
are chosen.
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
reference driver does clear the async interrupts after each service.
I'll tinker with this in a future commit.
Obtained from: Atheros
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
* Fix SLEEP1/SLEEP2 register definitions; the CAB/Beacon timeout
fields have changed in AR5416 and later
* The TIM_PERIOD and DTIM_PERIOD registers are now microsecond fields,
not TU.
Obtained from: Linux ath9k, Atheros reference
Approved by: re (kib, blanket)
or later. Previous hardware had some as TU, some as 1/8th
TU.
* Modify AR_NEXT_DBA and AR_NEXT_SWBA to use a new macro,
ONE_EIGHTH_TU_TO_USEC(), which converts the 1/8th TU
fields to USEC. This is just cosmetic and matches the
Atheros reference driver.
* Fix AR_NEXT_TBTT, which is USEC, not TU.
Submitted by: paradyse@gmail.com
Approved by: re (kib, blanket)
if 5ghz fast clock is enabled in the current operating mode.
It's slightly dirty, but it's part of the reference HAL and used by
the (currently closed-source) radar event code to map radar pulses
back to microsecond durations.
Obtained from: Atheros
Approved by: re (kib, blanket)
* I messed up the order of parameter true/false; oops!
* AR_PHY_RADAR_1 was being written at the wrong place, and was writing
potential garbage to the hardware.
Approved by: re (kib)
* Teach the AR5212/AR5416 ANI code to use the RX filter methods, rather
than calling the RX filter routines directly.
* Make HAL_ANI_PRESENT and HAL_ANI_MODE unconditionally available,
regardless of whether ah_ani_function is masking it.
* (Mostly) fully disable ANI if interference mitigation is disabled.
When disabled, the ANI code doesn't touch any ANI/PHY registers,
leaving them the default value. This is in line with what the
Atheros reference driver does.
* Correctly set the ANI parameters during ANI reset, rather than
when ANI is enabled. In this way, if ANI is disabled or enabled
whilst the NIC is not active (and there's no current channel),
bogus parameters or a NULL pointer deference doesn't occur.
There's still some lingering issues - notably, the MIB events/interrupts
aren't fully disabled, so MIB interrupts still occur. I'll worry about
that later.
Approved by: re (kib)
This in particular fixes radar PHY handling - on the AR5212
NIC, one enables the AR_PHY_ERR_RADAR bit in AR_PHY_ERR;
the AR5416 and later also needs a bit set in AR_RX_FILTER.
A follow-up commit is needed to convert the AR5416 ANI code
to use this particular method, as it's currently using the
AR5212 methods directly.
Obtained from: Atheros
Approved by: re (kib)
the ADC calibrations if the NIC is in 5ghz 11a or 5ghz HT/20 modes.
I've been told that the dual-ADC is only engaged in turbo/40mhz modes.
Since Sowl (AR9160) seems to return valid-looking calibration data
in 5ghz 20MHz modes, I'm only disabling it for Merlin for now.
It may turn out I can disable it for all chipsets and only enable
it for 40MHz modes.
Approved by: re (kib)
It looks like this was mixed up with the AR9285 calibration code.
This code is now more in line with what Linux ath9k and Atheros
reference drivers do.
Obtained from: Atheros
Approved by: re (kib)
tools.
* introduce pe_enabled, which (will) indicate whether the radar
detection stuff is enabled or not. Right now it's incorrectly
set, based on something previously written. I'll sort it out
later.
* Don't set HAL_PHYERR_PARAM_ENABLE in pe_relstep to say whether
radar detection is on.
* Return whether blockradar, fir128 and enmaxrssi is enabled.
* Change some of the phyerr params to be integers rather than
HAL_BOOL so they can be set to the NOPARAM value when the
setup function is called. This is in line with other radar
parameters.
* Add new configuration parameters for fir128, blockradar and
enmaxrssi, rather than defaulting to off, on and on respectively.
Approved by: re (kib)
polluting the AR5416 code with later chipset support.
Note: ar9280InitPLL() supports Merlin (AR9280) and later (AR9285, AR9287.)
Submitted by: ssgriffonuser@gmail.com
Approved by: re (kib)
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)
The global ath_hal_debug now affects all instances of the HAL.
This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.
rather than global variables.
This specifically allows for debugging to be enabled per-NIC, rather
than globally.
Since the ath driver doesn't know about AH_DEBUG, and to keep the ABI
consistent regardless of whether AH_DEBUG is enabled or not, enable the
debug parameter always but only conditionally compile in the debug
methods if needed.
The ALQ support is currently still global pending some brainstorming.
Submitted by: ssgriffonuser@gmail.com
Reviewed by: adrian, bschmidt
For the AR5211/AR5212, this is apparently a one byte pulse duration
counter value. It is only coded up here for the AR5212 as I don't have
any AR5211-series hardware to test it on.
This information was extracted from the Madwifi DFS branch along with
some local additions.
Please note - all this does is extract out the radar event duration,
it in no way reflects the presence of a radar. Further code is needed
to take a set of radar events and filter them to extract out correct
radar pulse trains (and ignore other events.)
For further information, please see:
http://wiki.freebsd.org/dev/ath_hal%284%29/RadarDetection
This includes references to the relevant patents which describe what
is going on.
Obtained from: Madwifi
Please note - this doesn't in any way constitute a full DFS
implementation, it merely adds the relevant capability bits and
radar detection threshold register access.
The particulars:
* Add new capability bits outlining what the DFS capabilities
are of the various chipsets.
* Add HAL methods to set and get the radar related register values.
* Add AR5212 and AR5416+ DFS radar related register value
routines.
* Add a missing HAL phy error code that's related to radar event
processing.
* Add HAL_PHYERR_PARAM, a data type that encapsulates the radar
register values.
The AR5212 routines are just for completeness. The AR5416 routines
are a super-set of those; I may later on do a drive-by pass to
tidy up duplicate code.
Obtained from: Linux, Atheros
It isn't linked into the build because it's missing the TX power
and PDADC programming code.
This code is mostly based on the ath9k codebase, compared against
the Atheros codebase as appropriate.
What's implemented:
* probe/attach
* EEPROM board value programming
* RX initial calibration
* radio channel programming
* general MAC / baseband setup
* async fifo setup
* open-loop tx power calibration
What's missing before it can be enabled by default:
* TX power / calibration setting code
* closed-loop tx power calibration routines
* TSF2 handling
* generic timer support from ath9k
Obtained from: Atheros, ath9k
