Doug Rabson's work, with a few tweaks from Warner Losh and I. There are
still some quirks to resolve, but the old driver is presently breaking
the build.
Fix a bug where video capture locks up on channel changes.
Many thanks to Juha for solving this.
Submitted by: Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
external NatSemi PHY chip was programmed to respond to MII address 24.
In the 3c905B ASICs, the transceiver is internal but it's still mapped
to MII address 24. But *some* 3Com 3c905B ASIC revisions map the
transceiver control registers to *all* MII addresses (0 through 31).
The miibus code probes for PHYs at all MII addresses and because of
this unusual behavior, it will attempt to map the same PHY registers
several times over, which doesn't work.
Naturally, the 3c905B NIC that I tested happened not to exhibit this
behavior.
The fix is to tweak xl_miibus_readreg() and xl_miibus_writereg()
to only respond when attempting to read from MII address 24. This
is safe to do since the 3Com documentation indicates that the PHY
and/or internal transceiver will always be mapped to address 24,
and there are no 3Com XL NICs with more than one PHY.
New Features:
Greatly improved VBI capture support. (mainly for the AleVT port)
Supports select() on /dev/vbi
Improved RISC program for RGB+VBI capture to capture both evenodd
VBI data even when only capturing even only (or odd only) video
Based on code from Juha Nurmela <Juha.Nurmela@quicknet.inet.fi>
Support for Hauppauge 627 and Temic 4006
Submitted by: Maurice Castro <maurice@atum.castro.aus.net>
Bug Fix:
Fix bug in AverMedia card detection.
Break out the detection logic for the aic7855 and properly report
these chips as 7855s instead of 7850s.
The 2940AU_CN is an aic7860 based card, not aic7860.
Not setting CACHETHEN turned out to be a bad idea. It can cause
spurious corruption under heavy PCI load with multiple masters.
due to the fact that there are non-MII cards supported by the same
driver and I don't have all of the cards available for testing. There's
also the 3c905B-COMBO which has MII, AUI and BNC media ports all in one
package. Supporting the COMBO is difficult because we have to add the
10base5 and 10base2 media types to the same ifmedia struct as the
MII-attached types, however there is no way to force the miibus and
child PHYs into existence before xl_attach() completes, so there is
no ifmedia struct available in xl_attach(). What we do inistead is
use the mediainit method as a callback: when a child PHY is attached,
it calls the miibus mediainit routine which selects a default media.
This routing also calls the NIC driver's mediainit method (if it
implements one) at which point we can safely add the other media
types.
This fixes, at least, panics in ncr_attach() on i386's with about 5MB
of memory. The restriction was a hack to leave some low memory for ISA
DMA, but on i386's we now allocate pages from the top down, so all the
restriction did was cause our allocations to fail when there is no free
memory above 1MB.
had to get the ML 6692 PHY driver working correctly, which is harder than
it sounds. "Bitrate" ThunderLAN devices should still be supported (i.e
the older 10Mbps Netflex 3/P, which use the TNETE110 chip that has no
MII support). The ThunderLAN has an internal PHY which makes things a
little complicated, but these are the basic rules:
- For devices with just the ThunderLAN, the internal PHY is used to
provide 10baseT, and 10base5/10baseT support. Autonegotiation will
work, but only with 10baseT links. The only thing that really gets
negotiated is whether the link is full or half duplex.
- For devices with the ThunderLAN and an external 10/100 PHY (like the
Compaq Netelligent 100Mbps cards, or the internal Netflex 3/P with
100Mbps upgrade daughter card), the external PHY is used for 10baseT
and 100baseTX modes. The internal PHY is still used to support
10base5/10base2, though you have to select them manual with ifconfig.
- For devices with the ThunderLAN and the ML6692 PHY, both the internal
and external PHYs are used, though it will appear as though the 6692
PHY will be used to support 10baseT and 100baseTX modes. In reality,
the internal PHY will be used for 10baseT, but this fact will be hidden
from the user. The 10base5/10base2 modes can also be selected manually
as with above.
in 4 byte chunks. It turns out that with the 82c169C on the Netgear
FA-310TX Rev D2, if you tell the chip you have reserved a buffer of 1518
bytes, it will actually treat it as 1516 bytes since 1518 is divisible
by four. Consequently, a packet of 1514 bytes will always end up consuming
two buffers: the last coupleof bytes will spill over into the next
descriptor. This causes the pn_rx_bug_war() routine to trip unnecessarily.
I'm not sure if the 82c169B or 82c168 chips behave the same way; I'll
have to check them. In any case, this change should work just as well
with them. Note that the FA-310TX Rev D2 also has a Broadcom PHY
instead of a Level One LXT970 PHY, however this shouldn't make any
difference as far as the driver is concerned.
This change also allows me to do a way with one rounding overation in
pn_rx-buf_war().
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
PCI fast ethernet controller. Currently, the only card I know that uses
this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the
only cards I have are samples sent to me by D-Link.)
This driver is the first to make use of the miibus code once I'm sure
it all works together nicely, I'll start converting the other drivers.
The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design
only with its own register layout. Support is provided for ifmedia,
hardware multicast filtering, bridging and promiscuous mode.
events, in order to pave the way for removing a number of the ad-hoc
implementations currently in use.
Retire the at_shutdown family of functions and replace them with
new event handler lists.
Rework kern_shutdown.c to take greater advantage of the use of event
handlers.
Reviewed by: green
to achieve a delay is pretty mean.
Andrew reports:
"The tulip_delay_300ns() is, well, bloody stupid on machines with a
heavily loaded PCI bus. It tries to do a delay by assuming PCI reads
will take a certain amount of time & issues a large amount of
(expensive, 5% CPU when your PCI bus is heavily loaded) pci reads.
Locally, we've replaced the calls to tulip_delay_300ns(sc) in the EMIT
macros with a simple DELAY(1) and not seen any problems. Plus we've
gained about 50Mb/sec throughput on our gigabit network cards because
of the added PCI bus bandwidth available."
Also, I do not understand why, but this change appears to stop the
Transmit Fifo underrun on one of my systems (but not the Alpha PC164SX).
This shouldn't make that much of a difference since the mii bus isn't
touched all that often, but perhaps when it does get accessed and hence
hammers the register, it was causing the chip to get upset.
Submitted by: Andrew Gallatin <gallatin@cs.duke.edu>
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
Isn't really that useful.
chip0: <PCI to Other bridge (vendor=10e0 device=8849)> at device 0.0 on pci0
is more in keeping with the spirit of the rest of the code.
Previous behavior with regard to truely unknown bridges unchanged.
"<Anti-Bill> Tell you what: you have commit privs now. You do it."
reset command.
I observed some anomalous behavior while testing a 3c905C with a
Dell PowerEdge 4300/500 dual PIII 500Mhz system. The NIC would seem
to work correctly most of the time but would sometimes fail to receive
certain packets, in particular NFS create requests. I could mount
an NFS filesystem from the PowerEdge and do an ls on it, but trying
to do a "touch foo" would hang. Monitoring traffic from another host
revealed that the client was properly sending an NFS create request
but the server was not receiving it. It *did* receive it when I
ran the same test with an Intel fxp card.
I don't understand the exact mechanics of this strange behavior, but
resetting the receiver and transmitter seems to get rid of it. I used
to perform an RX and TX reset in xl_init(), but stopped doing it there
because on 3c905B and later cards this causes the autoneg session to
restart, which would lead to the NIC waiting a long time before exchanging
traffic after being brought up the first time. Apparently the receiver
and transmitter resets should be performed at least once when initializing
the card.
Hopefully this will cure problems that people have been having with the
3c905C -- this was the only strange behavior that I have observed with
the 3c905C so far which does not appear with the 3c905B or 3c905.
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
been booted works too -- very neat. However I don't want the system to
stop for 5 seconds when the MII autoprobe is triggered in the xl and
tl drivers since that's lame. Instead, only use the hard delay when
we've been cold booted. If not, use the timeout mechanism instead.
(The SysKonnect driver doesn't use the same autonegotiation scheme, so
no change is required there.)
Also includes a workaround fro an apparent chip bug
where UDMA mode 2 can overpower the UDMA engine enough that it will
hog the PCI bus to the exclusion of the processor.
into a loadable module, and all of the platform dependencies are gone
(except for the alpha_XXX_dmamap() thing, which is another issue -- I
still don't know how to use the busdma stuff with a network driver).
Also increase the delay in xl_reset(); testing on a 486/66 with a 3c905C
shows that reading the EEPROM fails immediately after a reset. Waiting
a little longer after the reset completes seems to fix it.
interrupts that were scheduled. Testing shows it didn't really do very much
and it makes the code a little more complicated (which is never a good thing).
Also fix the rambuffer offset initialization for the 512K/64K SRAM case
(512K total using 64K chips). It should be 0. The only case with a
non-standard rambuffer offset address is 1024K/64K according to the
SysKonnect manual. (My card has the 1024/64 configuration and I don't know
which card uses the 512/64 configuration, if any, so I'm not sure that
this was really a problem for anyone.)
Change number of VBI lines from 16 to 12 for NTSC formats.
Juha.Nurmela@quicknet.inet.fi found/fixed bug in VBI_SLEEP.
New features
MSP3430G DBX initialisation from Matt Brown <matt@dqc.org>
STB Bt878 card identification.
Hauppauge Model Number identification.
Changes to probeCard() for better eeprom identification.
Experimental TDA9850 initialisation code, from Linux bttv.
Cross Platform Changes
The driver has been reorgainsed based ideas from Brad Parker's port to Linux
to seperate OS Dependant and Independant sections.
I have backends for FreeBSD 2.2.x/3.x and 4.x newbus, BSDI, OpenBSD and NetBSD.
This commit has FreeBSD 2.2.8/2.2-stable/3.x and FreeBSD 4.x newbus backends.
Some code submitted by: Juha.Nurmela@quicknet.inet.fi
Matt Brown <matt@dqc.org>
Brad Parker <brad@parker.boston.ma.us>
Some code obtained from: Linux bttv driver
gigabit ethernet adapters. This includes two single port cards
(single mode and multimode fiber) and two dual port cards (also single
mode and multimode fiber). SysKonnect is currently the only
vendor with a dual port gigabit ethernet NIC.
The ports on dual port adapters are treated as separate network
interfaces. Thus, if you have an SK-9844 dual port SX card, you
should have both sk0 and sk1 interfaces attached. Dual port cards
are implemented using two XMAC II chips connected to a single
SysKonnect GEnesis controller. Hence, dual port cards are really
one PCI device, as opposed to two separate PCI devices connected
through a PCI to PCI bridge. Note that SysKonnect's drivers use
the two ports for failover purposes rather that as two separate
interfaces, plus they don't support jumbo frames. This applies to
their Linux driver too. :)
Support is provided for hardware multicast filtering, BPF and
jumbo frames. The SysKonnect cards support TCP checksum offload
however this feature is not currently enabled (hopefully it will
be once we get checksum offload support).
There are still a few things that need to be implemeted, like
the ability to communicate with the on-board LM80 voltage/temperature
monitor, but I wanted to get the driver under CVS control and into
-current so people could bang on it.
A big thanks for SysKonnect for making all their programming info
for these cards (and for their FDDI and token ring cards) available
without NDA (see www.syskonnect.com).
clears out the transmit queue and zeroes the downlist pointer register,
but xl_txeof() isn't called before xl_start() tries to queue more packets,
xl_start() will think that the DMA is still in progress and not update
the downlist register again, thus causing packets to sit in the transmit
queue forever.
Patch provided by: Russell T Hunt <alaric@MIT.EDU>
