- Add partial promiscuous mode support (no management frames;
they cannot be received by the firmware and net80211 at the same time).
- Add monitor mode support (all frames).
Tested with Asus, USB-N10.
This is required for USB Rx aggregation
(and fixes 'could not allocate RX mbuf' / few other failures).
While here, reduce the number of Rx buffers from 100 to 1 -
the driver never uses more than one Rx buffer.
Tested with Asus USB-N10.
This change includes firmware commands for key setup +
some additional checking via CAMREAD / CAMWRITE registers.
Nothing (except rsu_delete_key() for pairwise keys) is deferred;
to ensure that things are done in order rsu_set_key() will wait
until key deletion task will be finished.
Tested with Asus USB-N10 (all ciphers).
Differences from initial (reviewed) patch:
- Pause AC queues before disassociation - since CMD_DISCONNECT clears
crypto state all pending frames must be processed / dropped before it.
- Check sc_running flag before trying to set static keys.
- Clear key index from bitmap even when firmware command fails
(it will be invalidated via CAMWRITE anyway).
Reviewed by: adrian, kevlo
Tested by: kevlo
Differential Revision: https://reviews.freebsd.org/D8706
- Append RCR_APP_PHYSTS bit after firmware loading - otherwise
firmware will reset the register and this modification will be lost.
(without it Rx PHY descriptor section will contain garbage).
- Check if R92S_RXDW0_PHYST bit is set (like it is done in rtwn(4)) -
even if infosz is non-zero the section may not contain anything useful.
- In case, if descriptor is absent (A-MPDU?) use last calibrated RSSI
(rtwn(4) uses RSSI from the previous (sub)frame; probably, this
approach should be used here too).
Tested with Asus USB-N10, STA mode.
- Set IEEE80211_FEXT_SCAN_OFFLOAD flag; firmware can send null data
frames when associated.
- Check IEEE80211_SCAN_ACTIVE scan flag instead of IEEE80211_F_ASCAN
ic flag; the last is never set since r170530.
- Eliminate software scan (net80211) <-> site_survey (driver) race:
* override ic_scan_curchan and ic_scan_mindwell pointers so net80211
will not try to finish scanning automatically;
* inform net80211 about current status via ieee80211_cancel_scan()
and ieee80211_scan_done();
* remove corresponding workaround from rsu_join_bss().
Now the driver can associate to an AP with hidden SSID.
Tested with Asus USB-N10.
The fullmac firmware doesn't seem to populate a useful rssi indicator
in the RX descriptor, so if one plotted said values, they'd basically
look like garbage.
The reference driver implements a "get current rssi" firmware command
which I guess is really meant for station operation only (as hostap
operation would need rssi per station, not a single firmware read.)
So:
* populate sc_currssi during each calibration run;
* use this in the RX path instead of trying to reconstruct the RSSI
value and passing it around as a pointer;
* do up a quick hack to map the rssi hardware value to some useful
signal level;
* the survey results provide an RSSI value between 0..100, so just
do another quick hack to map it into some usefulish signal level;
* supply a faked noise floor - I haven't yet found how to pull it
out of the firmware.
The scan results and the station RSSI information is now more useful
for indicating signal strength / distance.
This logic is mostly crimed from the reference driver and the linux
r92su driver.
I verified that it (a) worked on the rsu hardware I have, and (b)
did traffic testing whilst watching what ath(4) sent as a hostap.
It successfully sent MCS8..15 rates (which requires 2-stream reception)
as well as MCS0..7 (which is 1-stream.)
Tested:
* RTL8712, 1T1R NIC, MCS rates 0..7.
* RTL8712, 1T2R NIC, MCS rates 0..15
TODO:
* Find a 2T2R NIC!
* Add a new method to control NIC poweron / network-sleep / power off;
* Add in A-MPDU TX negotiation support, but comment it out because it
does break TX traffic;
* blank out the tx buffer before sending a firmware message, just in case;
* go into network-sleep once associated;
TODO:
* figure out why ampdu negotiation isn't working and breaking TX traffic,
then enable it.
to do it directly.
Ensure that we re-queue starting transmit upon TX completion.
This solves two issues:
* It stops tx stalls - before this, if the transmit path filled the
mbuf queue then it'd never start another transmit.
* It enforces ordering - this is very required for 802.11n which
requires frames to be transmitted in the order they're queued.
Since everything remotely involved in USB has an unlock/thing/relock
pattern with that mutex, the only way to guarantee TX ordering is
to 100% defer it into a separate thread.
This now survives an iperf test and gets a reliable 30mbit/sec.
requirements.
Don't start the opmode and join path until a pending survey is finished.
This seems to reliably fix things.
Ideally I'd just finish off the net80211 pluggable scan stuff and implement
the methods here so if_rsu can just drive the scan machinery.
However, that's a .. later thing.
Whilst here, remove the getbuf debugging; it's okay to run out of transmit
buffers under load; it however isn't okay to not be able to send commands.
I'll fix that later.
data queues.
This is similar to the openbsd and rtlwifi/r92su drivers.
Note: this driver still assumes it's a 4-endpoint device; I'll enforce
that in a follow-up commit.
connectivity interact with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to pluknet@, Oliver Hartmann,
Olivier Cochard, gjb@, mmoll@, op@ and lev@, who also participated in
testing.
Reviewed by: adrian
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
* 286410
* 286413
* 286416
The initial commit broke a variety of debug and features that aren't
in the GENERIC kernels but are enabled in other platforms.
with the net80211 stack.
Historical background: originally wireless devices created an interface,
just like Ethernet devices do. Name of an interface matched the name of
the driver that created. Later, wlan(4) layer was introduced, and the
wlanX interfaces become the actual interface, leaving original ones as
"a parent interface" of wlanX. Kernelwise, the KPI between net80211 layer
and a driver became a mix of methods that pass a pointer to struct ifnet
as identifier and methods that pass pointer to struct ieee80211com. From
user point of view, the parent interface just hangs on in the ifconfig
list, and user can't do anything useful with it.
Now, the struct ifnet goes away. The struct ieee80211com is the only
KPI between a device driver and net80211. Details:
- The struct ieee80211com is embedded into drivers softc.
- Packets are sent via new ic_transmit method, which is very much like
the previous if_transmit.
- Bringing parent up/down is done via new ic_parent method, which notifies
driver about any changes: number of wlan(4) interfaces, number of them
in promisc or allmulti state.
- Device specific ioctls (if any) are received on new ic_ioctl method.
- Packets/errors accounting are done by the stack. In certain cases, when
driver experiences errors and can not attribute them to any specific
interface, driver updates ic_oerrors or ic_ierrors counters.
Details on interface configuration with new world order:
- A sequence of commands needed to bring up wireless DOESN"T change.
- /etc/rc.conf parameters DON'T change.
- List of devices that can be used to create wlan(4) interfaces is
now provided by net.wlan.devices sysctl.
Most drivers in this change were converted by me, except of wpi(4),
that was done by Andriy Voskoboinyk. Big thanks to Kevin Lo for testing
changes to at least 8 drivers. Thanks to Olivier Cochard, gjb@, mmoll@,
op@ and lev@, who also participated in testing. Details here:
https://wiki.freebsd.org/projects/ifnet/net80211
Still, drivers: ndis, wtap, mwl, ipw, bwn, wi, upgt, uath were not
tested. Changes to mwl, ipw, bwn, wi, upgt are trivial and chances
of problems are low. The wtap wasn't compilable even before this change.
But the ndis driver is complex, and it is likely to be broken with this
commit. Help with testing and debugging it is appreciated.
Differential Revision: D2655, D2740
Sponsored by: Nginx, Inc.
Sponsored by: Netflix
- The R92S_TCR register is an 8-bit register. Don't access it like a
16-bit register.
- Disable parsing the delete station event, due to many false events.
- Ensure that there is only one transfer queue for each endpoint, so
that packets transmitted don't get out of order.
MFC after: 1 week
be a race when using a single active queue for all transmit types.
- Last argument of usb_pause_mtx() is ticks and not milliseconds.
- Remove unused watchdog.
- Remove some unused fields from the RSU softc structure.
- Workaround usbd_transfer_start() recursion from inside of completion
callback.
MFC after: 3 days
Support chipsets are the Realtek RTL8188SU, RTL8191SU, and RTL8192SU.
Many thanks to Idwer Vollering for porting/writing the man page and for
testing.
Reviewed by: adrian, hselasky
Obtained from: OpenBSD
Tested by: kevlo, Idwer Vollering <vidwer at gmail.com>
