Submitted by: Andy Moreton <amoreton at solarflare.com>
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D4331
It seems the EEE made RX MAC enter LPI(Low Power Idle) mode such
that dwc(4) was not able to receive packets. Ideally dwc(4) should
be able to use EEE to save power during periods of low link
utilization(i.e. gating off clock). Due to lack of dwc(4)
datasheet it's not easy to take required steps for EEE on LPI
enter/exit events. Disabling EEE in PHY seems to be easy
workaround until dwc(4) supports EEE.
Updating EEE advertisement register on RTL8211F seems to have no
effect until reprogramming MII_ANAR, MII_100T2CR and MII_BMCR
with auto-negotiation. It's not clear whether it's related with
mii_phy_reset()'s BMCR_ISO handling for RTL8211F though.
It seems rgephy_reset() needs careful investigation for newer
RealTek PHYs.
Ganbold submitted working version based on NetBSD change and
tested lots of changes I made. Thanks a lot!
Submitted by: ganbold (initial version)
In collaboration with: ganbold
the malloc() + memset() in the local implementation of calloc() into a call
to calloc(), helpfully turning it into an infinite loop. Clean up some
unneeded flags on PPC64 while here.
MFC after: 1 month
Each virtual interface has its own MAC address, queues, and statistics.
The dedicated netmap interfaces (ncxgbeX / ncxlX) were already implemented
as additional VIs on each port. This change allows additional non-netmap
interfaces to be configured on each port. Additional virtual interfaces
use the naming scheme vcxgbeX or vcxlX.
Additional VIs are enabled by setting the hw.cxgbe.num_vis tunable to a
value greater than 1 before loading the cxgbe(4) or cxl(4) driver.
NB: The first VI on each port is the "main" interface (cxgbeX or cxlX).
T4/T5 NICs provide a limited number of MAC addresses for each physical port.
As a result, a maximum of six VIs can be configured on each port (including
the "main" interface and the netmap interface when netmap is enabled).
One user-visible result is that when netmap is enabled, packets received
or transmitted via the netmap interface are no longer counted in the stats
for the "main" interface, but are not accounted to the netmap interface.
The netmap interfaces now also have a new-bus device and export various
information sysctl nodes via dev.n(cxgbe|cxl).X.
The cxgbetool 'clearstats' command clears the stats for all VIs on the
specified port along with the port's stats. There is currently no way to
clear the stats of an individual VI.
Reviewed by: np
MFC after: 1 month
Sponsored by: Chelsio
relax it a bit so gecos can be used to store multibytes data.
This was unseen before FreeBSD 10.2 as this validation function was motly unused
since FreeBSD 10.2 the usage of this function has been generalized to improve
validation.
Reported by: des
MFC after: 1 week
like the various d_*_t typedefs since it declared a function pointer rather
than a function. Add a new d_priv_dtor_t typedef that declares the function
and can be used as a function prototype. The previous typedef wasn't
useful outside of the cdevpriv implementation, so retire it.
The name d_priv_dtor_t was chosen to be more consistent with cdev methods
since it is commonly used in place of d_close_t even though it is not a
direct pointer in struct cdevsw.
Reviewed by: kib, imp
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D4340
This fixes detection of root interrupt controller for cases,
when interrupt parent is not defined at all or it's not defined directly
in controller node.
Approved by: kib (mentor)
This leak was introduced by r291527.
Since the nfscommon.ko module is rarely unloaded, this leak would not
have been much of an issue.
MFC after: 2 weeks
This is to fix 'make all' causing it to recurse on both 'all' and 'buildconfig'
due to 'buildconfig' being in ALL_SUBDIR_TARGETS and being a dependency of
'all'.
This now adds all of the '*includes', '*files' targets as subdir targets,
allowing them to recurse.
This also removes the need for some 'realinstall' hacks in bsd.subdir.mk since
it no longer recurses; only 'install' will recurse and call the proper
'beforeinstall', 'realinstall', and 'afterinstall' in each sub-directory.
This fixes 'make includes' and 'make files' to not be a rerolled ${MAKE}
sub-shell but to rather just recurse on 'inclues' and 'files'. This avoids
various issues such as the one fixed in r289462. As such revert Makefile.inc1
back to using 'includes' which avoids an extra tree walk and parallelizes
the includes phases better.
Makefile.inc1 includes a guard so that 'make all' will not use SUBDIR_PARALLEL,
added in r289438. This is so users do not get a probably broken build if they
run 'make all' from the top-level. Before the change in this commit, the
workaround for 'make everything' was 'par-all' which would depend on 'all' and
cause a proper parallel recursion. Now that will not work so a new
_PARALLEL_SUBUDIR_OK is used to allow it.
This is still part of an effort to combine bsd.(files|incs|confs).mk and move
some of its logic out of bsd.subdir.mk, as attempted in r289282 and reverted in
r289331. This commit fixes the problems found there which was mostly double
recursing during 'includes' which would recurse on itself and 'buildincludes'
and 'installincludes', all in parallel. The logic is still in bsd.subdir.mk
for now.
I've been cautious about this commit but have experienced no breakage on the
tree except for the 'par-all' case which was already a hack. If something foo
is depending on something bar that should recurse, it is very likely that the
foo target is being recursed on already meaning that bar will still effectively
recurse once sub-directories call foo.
Discussed on: arch@
MFC after: never
Sponsored by: EMC / Isilon Storage Division
This is to fix 'make all' causing it to recurse on both 'all' and 'buildconfig'
due to 'buildconfig' being in ALL_SUBDIR_TARGETS and being a dependency of
'all'.
This now adds all of the '*includes', '*files' targets as subdir targets,
allowing them to recurse.
This also removes the need for some 'realinstall' hacks in bsd.subdir.mk since
it no longer recurses; only 'install' will recurse and call the proper
'beforeinstall', 'realinstall', and 'afterinstall' in each sub-directory.
This fixes 'make includes' and 'make files' to not be a rerolled ${MAKE}
sub-shell but to rather just recurse on 'inclues' and 'files'. This avoids
various issues such as the one fixed in r289462. As such revert Makefile.inc1
back to using 'includes' which avoids an extra tree walk and parallelizes
the includes phases better.
Makefile.inc1 includes a guard so that 'make all' will not use SUBDIR_PARALLEL,
added in r289438. This is so users do not get a probably broken build if they
run 'make all' from the top-level. Before the change in this commit, the
workaround for 'make everything' was 'par-all' which would depend on 'all' and
cause a proper parallel recursion. Now that will not work so a new
_PARALLEL_SUBUDIR_OK is used to allow it.
This is still part of an effort to combine bsd.(files|incs|confs).mk and move
some of its logic out of bsd.subdir.mk, as attempted in r289282 and reverted in
r289331. This commit fixes the problems found there which was mostly double
recursing during 'includes' which would recurse on itself and 'buildincludes'
and 'installincludes', all in parallel. The logic is still in bsd.subdir.mk
for now.
I've been cautious about this commit but have experienced no breakage on the
tree except for the 'par-all' case which was already a hack. If something foo
is depending on something bar that should recurse, it is very likely that the
foo target is being recursed on already meaning that bar will still effectively
recurse once sub-directories call foo.
Discussed on: arch@
MFC after: never
Sponsored by: EMC / Isilon Storage Division
Fix current findings, which should fix cases of NO_SHARED not building
properly.
Given libfoo:
- Ensure that a LIBFOO is set. For INTERNALLIBS advise setting this in
src.libnames.mk, otherwise bsd.libnames.mk.
- Ensure that a LIBFOODIR is properly set.
- Ensure that _DP_foo is set and matches the LIBADD in the build of foo's own
Makefile
Sponsored by: EMC / Isilon Storage Division
I'm not sure why this was here, none of these use pthread themselves and
none of the consumers are broken with removing this.
Sponsored by: EMC / Isilon Storage Division
The proper place for this list is _DP_dtrace.
Due to removing the LDADD_dtrace, more LIBADD are needed in
cddl/usr.sbin/dtrace to prevent underlinking.
This fixes overlinking in cddl/usr.sbin/lockstat and
cddl/usr.sbin/plockstat.
Sponsored by: EMC / Isilon Storage Division
This change came in r281332 which was reducing overlinking in mt(1) but
currently mt(1) is linked with sbuf when it does not need it due to the
LDADD_mt+=${LDADD_sbuf}. Only libmt needs sbuf.
Add sbuf to _DP_mt so static linkage of libmt picks it up.
Sponsored by: EMC / Isilon Storage Division
Fix current findings.
Given libfoo:
- Ensure that a LIBFOO is set. For INTERNALLIBS advise setting this in
src.libnames.mk, otherwise bsd.libnames.mk.
- Ensure that a LIBFOODIR is properly set.
- Ensure that _DP_foo is set and matches the LIBADD in the build of foo's own
Makefile
Sponsored by: EMC / Isilon Storage Division
"don't know how to make /Versions.def. Stop"
This was trying to define a target in bsd.symver.mk based on LIBCDIR which was
not yet defined. Switching the order of inclusion of bsd.prog.mk and
bsd.symver.mk fixes it and seems fine.
Pointyhat to: bdrewery
Sponsored by: EMC / Isilon Storage Division
This had no real impact since libipf is a static INTERNALLIB. It does conflict
with an assertion I am adding for LIBADD though.
Sponsored by: EMC / Isilon Storage Division
