something: offset into the first mbuf of the target chain before copying
the source data over.
Make drivers using m_devget() with a first argument "data - ETHER_ALIGN"
to use the offset argument to pass ETHER_ALIGN in. The way it was previously
done is potentially dangerous if the source data was at the top of a page
and the offset caused the previous page to be copied (if the
previous page has not yet been appropriately mapped).
The old `offset' argument in m_devget() is not used anywhere (it's always
0) and dates back to ~1995 (and earlier?) when support for ethernet trailers
existed. With that support gone, it was merely collecting dust.
Tested on alpha by: jlemon
Partially submitted by: jlemon
Reviewed by: jlemon
MFC after: 3 weeks
the console device was open. At other times, the interrupts that
are used to detect the break signal or ~^B sequence were disabled,
so these events would not be noticed until the next open (e.g. the
next kernel printf). This was mainly a problem while there was no
getty running on the console, such as during bootup or shutdown.
For serial consoles with break-to-debugger support, we now enable
the generation of interrupts at attach time, and we leave them
enabled while the device is closed.
Reviewed by: bde (I've since made chages as per his suggestions)
via the new DIGIIO_SETALTPIN ioctl, and allow the port's ALTPIN setting
to be queried via DIGIIO_GETALTPIN.
The initial state and lock devices are normally used to set and/or
lock ALTPIN settings although the device itself may also be used.
ALTPIN settings are applied per-device and apply to both the callin
and callout device at the same time.
the following description in RFC2461:
AdvSendAdvertisements
A flag indicating whether or not the router sends
periodic Router Advertisements and responds to
Router Solicitations.
Default: FALSE
Note that AdvSendAdvertisements MUST be FALSE by
default so that a node will not accidentally start
acting as a router unless it is explicitly
configured by system management to send Router
Advertisements.
Submitted by: JINMEI Tatuya <jinmei@isl.rdc.toshiba.co.jp>
MFC after: 1 week
sizeof(ro_dst) is not necessarily the correct one.
this change would also fix the recent path MTU discovery problem for the
destination of an incoming TCP connection.
Submitted by: JINMEI Tatuya <jinmei@kame.net>
Obtained from: KAME
MFC after: 2 weeks
of tunclose() rather than the end, and tunopen() grabbed that unit
before tunclose() finished (one process is allocating it while another
is freeing it!).
It may be worth hanging some sort of rw mutex around all specinfo
calls where d_close and the detach handler get a write lock and all
other functions get a read lock. This would guarantee certain levels
of ``atomicity'' (is that a word?) that people may expect (I believe
Solaris does something like this).
exist, and therefore mm_install is returning the "fail" value of
the test instead of the "success" value for install.
This change is a no-op on HEAD, but since the only harm on RELENG_4
ATM is a spurious warning it can follow the usual MFC practice.
Submitted by: A cast of thousands :-/
columns confuse the heck out of other apps trying to parse vmstat output
(eg sscope). I made sure we're still <= 80 cols per line.
Fixed warnings about unused vars and printf %format mismatches.
Requested by: Eugene Aleynikov <eugenea@infospace.com>
Reviewed by: joerg (implicitly)
MFC after: 2 weeks
requirements(RFC1573, interface MIB). This change for 4.4BSD was
first introduced in if_ethersubr.c:1.17->1.18.
BTW, iflastchange on all of IFs are inconsistent. e.g.
ether, tun: update
fddi, tokenring, ppp: not update
I'll make patch later.
Obtained from: KAME
MFC after: 2 weeks
