isn't configurable in a meaningful way. This is for ifconfig(8) or
other tools not to change code whenever IFT_USB-like interfaces are
registered at the interface list.
Reviewed by: brooks
No objections: gavin, jkim
looking to see if there is an existing IRQ resource for a given IRQ
provided by the BIOS and using that RID if so. Otherwise, allocate a new
RID for the new IRQ.
Reviewed by: mav (a while ago)
In particular, this check avoids a warning when
extracting directory entries from certain GNU tar
archives that store directory contents.
MFC after: 3 days
detected ashift does not support this. With this change, pools
created while stripesize=512 could not be imported when stripesize
becomes larger (on the same drive).
Noticed by: pjd
In exec_linux_setregs(), use locally cached pointer to pcb to set
pcb_full_iret.
In set_regs(), note that full return is needed when code that sets
segment registers is enabled.
MFC after: 1 week
The dealock was caused in the following way:
- thread T1 on CPU C1 holds a spin mutex, IPIs CPU C2 and waits for the
IPI to be handled
- C2 executes timer interrupt filter, thus has interrupts disabled, and
gets blocked on the spin mutex held by T1
The problem seems to have been introduced by simplifications made to
OpenSolaris code during porting.
The problem is fixed by reorganizing the code to more closely resemble
the upstream version. Interrupt filter (cyclic_fire) now doesn't
acquire any locks, all per-CPU data accesses are performed on a
target CPU with preemption and interrupts disabled thus precluding
concurrent access to the data.
cyp_mtx spin mutex is used to disable preemtion and interrupts; it's not
used for classical mutual exclusion, because xcall already serializes
calls to a CPU. It's an emulation of OpenSolaris
cyb_set_level(CY_HIGH_LEVEL) call, the spin mutexes could probably be
reduced to just a spinlock_enter()/_exit() pair.
Diff with upstream version is now reduced by ~500 lines, however it still
remains quite large - many things that are not needed (at the moment) or
are irrelevant on FreeBSD were simply ripped out during porting.
Examples of such things:
- support for CPU onlining/offlining
- support for suspend/resume
- support for running callouts at soft interrupt levels
- support for callout rebinding from CPU to CPU
- support for CPU partitions
Tested by: Artem Belevich <fbsdlist@src.cx>
MFC after: 3 weeks
X-MFC with: r216252
The code to translate the internal representation to text did not know about
various additions to the internal representation since the original ash and
therefore wrote binary stuff to the terminal.
The code is used in the jobs command and similar output.
Note that the output is far from complete and mostly serves for recognition
purposes.
on release CDs and so will normally fail.
installCommit() returns a DITEM_ value, not a Boolean.
distExtractAll() returns a Boolean, not a DITEM_ value.
Reported by: kensmith
MFC after: 3 days
max_request_segments * PAGE_SIZE if the I/O is page-aligned; the
largest I/O we can guarantee will work is PAGE_SIZE less than that.
This unbreaks 'diskinfo -t'.
and set *procp to NULL in all cases. Previously, it was not being set
in the ERESTART case. This is effectively no-op, since its value is
ignored by callers in the error case.
Reviewed by: kib@
as an association ID is set any scan is supposed to be a background scan.
This implies that the firmware will switch back to the associated channel
after a certain threshold, though, we are not notified about that. We
currently catch this case by a timer which will reset the firmware after
a 'scan timeout', though, upper layers are not notified about that and
will simply hang until manual intervention. Fix this by resetting the
firmware's knowledge about any association on RUN -> ASSOC and
!INIT -> SCAN transitions.
Tested by: Zhihao Yuan <lichray at gmail.com>
MFC after: 1 week
- Do not call iwn_calib_reset() for monitor mode. We do not want to query
information and do runtime calibration while in monitor mode. Poking the
firmware with adjustments for calibration results in firmware asserts.
This could happened on RUN -> RUN transition only.
- Adjust blink rate for monitor mode. It's supposed to not freak out and
turn off after a while.
- While here, remove one useless assignment of calib.state, it gets
overwritten later in the function.
Submitted by: Brandon Gooch <jamesbrandongooch at gmail.com>
MFC after: 1 week
preserve the upper bits of the first data byte.
While here, shorten a few nearby lines.
PR: kern/152768
Reported by: Sascha Wildner saw of online.de
Reviewed by: scottl
MFC after: 1 week
execve(2). Note that ia32 binaries already handle this properly,
since ia32_setregs() resets td_retval[1], but not exec_setregs().
We still do not conform to the amd64 ABI specification, since %rsp
on the image startup is not aligned to 16 bytes.
PR: amd64/124134
Discussed with: Petr Salinger <Petr.Salinger seznam cz>
(who convinced me that there is indeed several bugs)
MFC after: 1 week
alignment on drives with large sector sizes (e.g. 4 KiB) but the
implementation might need to be revisited if devices with large stripesizes
appear (e.g. if RAID controllers or flash drives start using the field),
probably by introducing a physsectorsize field in GEOM providers.
Discussed with: mav, mostly silence on freebsd-geom@ and freebsd-fs@
1.21
"Document the flags displayed by the default format, and mention their short
names. From espie@openbsd via jmc@openbsd."
1.24
"Fix three variable names.
From Todd T. Fries via Jason McIntyre."
Obtained from: wiz@NetBSD.org (previous 2)
1.25
"Be consistent: document the birthtime field of struct stat for
the "B" field specifier."
Obtained from: reed@NetBSD.org
1.26
"Drop trailing space."
Obtained from: wiz@NetBSD.org
1.27
"Since we have st_birthtime in struct stat, it is in default display."
Obtained from: enami@NetBSD.org
Purposely skipping the following revisions:
1.22 NetBSD-specific change
1.23 Removal of license clauses 3 and 4, already handled by imp
in our r203971
If describing the status of a pipeline, write all elements of the pipeline
and show the status of the last process (which would also end up in $?).
Only write one report per job, not one for every process that exits.
To keep some earlier behaviour, if any process started by the shell in a
foreground job terminates because of a signal, write a message about the
signal (at most one message per job, however).
Also, do not write messages about signals in the wait builtin in
non-interactive shells. Only true foreground jobs now write such messages
(for example, "Terminated").
