One of the fun issues with scanning has been how the existing
ANI values were programmed into the hardware when channels were
changed. If you're on a really crappy channel and ANI has made
you deaf then when you scan you continue to be deaf on all channels.
This code passes in a flag to startpcureceive which in AR5416 and later
is also used to enable ANI. This allows it to know if it's a normal
operation or a scan operation.
This fixes my situation at home where a temporary spot of a device
going deaf due to interference starts scanning and .. can't hear
anything until I restart.
Now, this isn't the full fix - ideally:
(a) all the ANI config and per-channel information would be migrated
to the shared HAL stuff and enabled for all of the NICs;
(b) when a station reassociates and some other error conditions
(like missed beacons, NF calibration failures, etc) a knob
to reset ANI parameters would likely help recovery.
But hey, I'm committing bits of code again! woo!
Tested:
* AR9344 (2G), STA operation
* The ani function bitmap was being badly used when determining if a command
could be used. In hostap modes only a couple of the ANI control parameters
are enabled.
* The ani function bitmap was not being reset to HAL_ANI_ALL if transitioning
from AP -> STA.
* Change mrcCckOff to mrcCck - 1 == on, rather than 1 == off. This matches
the API used to set the value from userland via the diagnostic API.
* Handle OFDM/CCK noise immunity level commands in ar9300_ani_control().
These will only come from userland and it will go and program the rest of
the ANI control parameters with the values in the ANI table.
* Ensure all of the ANI parameters can be tweaked at runtime, even if they're
disabled.
Tested:
* carambola2 (AR9331), STA/AP modes
I'm trying to debug why reception upstairs here is so terrible and it
turns out ANI is buggy. (Which is no surprise, ANI is always buggy.)
Tested:
* Carambola2 (AR9331), STA/AP modes
If we fail noise floor calibration then we may end up with a deaf NIC
which we can't recover without a full chip reset.
Earlier chips seem to get less stuck in this condition versus AR9280/later
and AR9300/later, but whilst here just fix up the AR5212 era chips to also
return NF calibration failures.
This HAL routine would only return failure if the channel was not configured.
This is a no-op until the driver side code for doing resets and the HAL
code for being told about the reset type (and then handling it!) is
implemented.
Tested:
* AR9280, STA mode
* AR2425, STA mode
* AR9380, STA mode
I'm in the process of reworking how the reset path works with an eye
to better recovery when the chips hang and/or go RF/PHY deaf.
This is the first step in a lot of unification and API changes.
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
It turned out, that some models of the Atheros PCIe
adapters (e.g. AR983x family) may fail to attach
due to insufficient timeout value.
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Reviewed by: adrian
Differential revision: https://reviews.freebsd.org/D10903
In the deep past, when this code compiled as a binary module, ath_hal
built as a module. This allowed custom, smaller HAL modules to be built.
This was especially beneficial for small embedded platforms where you
didn't require /everything/ just to run.
However, sometime around the HAL opening fanfare, the HAL landed here
as one big driver+HAL thing, and a lot of the (dirty) infrastructure
(ie, #ifdef AH_SUPPORT_XXX) to build specific subsets of the HAL went away.
This was retained in sys/conf/files as "ath_hal_XXX" but it wasn't
really floated up to the modules themselves.
I'm now in a position where for the reaaaaaly embedded boards (both the
really old and the last couple generation of QCA MIPS boards) having a
cut down HAL module and driver loaded at runtime is /actually/ beneficial.
This reduces the kernel size down by quite a bit. The MIPS modules look
like this:
adrian@gertrude:~/work/freebsd/head-embedded/src % ls -l ../root/mips_ap/boot/kernel.CARAMBOLA2/ath*ko
-r-xr-xr-x 1 adrian adrian 5076 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_dfs.ko
-r-xr-xr-x 1 adrian adrian 100588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal.ko
-r-xr-xr-x 1 adrian adrian 627324 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal_ar9300.ko
-r-xr-xr-x 1 adrian adrian 314588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_main.ko
-r-xr-xr-x 1 adrian adrian 23472 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_rate.ko
And the x86 versions, like this:
root@gertrude:/home/adrian # ls -l /boot/kernel/ath*ko
-r-xr-xr-x 1 root wheel 36632 May 24 18:32 /boot/kernel/ath_dfs.ko
-r-xr-xr-x 1 root wheel 134440 May 24 18:32 /boot/kernel/ath_hal.ko
-r-xr-xr-x 1 root wheel 82320 May 24 18:32 /boot/kernel/ath_hal_ar5210.ko
-r-xr-xr-x 1 root wheel 104976 May 24 18:32 /boot/kernel/ath_hal_ar5211.ko
-r-xr-xr-x 1 root wheel 236144 May 24 18:32 /boot/kernel/ath_hal_ar5212.ko
-r-xr-xr-x 1 root wheel 336104 May 24 18:32 /boot/kernel/ath_hal_ar5416.ko
-r-xr-xr-x 1 root wheel 598336 May 24 18:32 /boot/kernel/ath_hal_ar9300.ko
-r-xr-xr-x 1 root wheel 406144 May 24 18:32 /boot/kernel/ath_main.ko
-r-xr-xr-x 1 root wheel 55352 May 24 18:32 /boot/kernel/ath_rate.ko
.. so you can see, not building the whole HAL can save quite a bit.
For example, if you don't need AR9300 support, you can actually avoid
wasting half a megabyte of RAM. On embedded routers this is quite a
big deal.
The AR9300 HAL can be later further shrunk because, hilariously,
it indeed supports AH_SUPPORT_<xxx> for optionally adding chipset support.
(I'll chase that down later as it's quite a big savings if you're only
building for a single embedded target.)
So:
* Create a very hackish way to load/unload HAL modules
* Create module metadata for each HAL subtype - ah_osdep_arXXXX.c
* Create module metadata for ath_rate and ath_dfs (bluetooth is
currently just built as part of it)
* .. yes, this means we could actually build multiple rate control
modules and pick one at load time, but I'd rather just glue this
into net80211's rate control code. Oh well, baby steps.
* Main driver is now "ath_main"
* Create an "if_ath" module that does what the ye olde one did -
load PCI glue, main driver, HAL and all child modules.
In this way, if you have "if_ath_load=YES" in /boot/modules.conf
it will load everything the old way and stuff should still work.
* For module autoloading purposes, I actually /did/ fix up
the name of the modules in if_ath_pci and if_ath_ahb.
If you want to selectively load things (eg on ye cheape ARM/MIPS platforms
where RAM is at a premium) you should:
* load ath_hal
* load the chip modules in question
* load ath_rate, ath_dfs
* load ath_main
* load if_ath_pci and/or if_ath_ahb depending upon your particular
bus bind type - this is where probe/attach is done.
TODO:
* AR5312 module and associated pieces - yes, we have the SoC side support
now so the wifi support would be good to "round things out";
* Just nuke AH_SUPPORT_AR5416 for now and always bloat the packet
structures; this'll simplify other things.
* Should add a simple refcnt thing to the HAL RF/chip modules so you
can't unload them whilst you're using them.
* Manpage updates, UPDATING if appropriate, etc.
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
The HT40 channel population logic was "just" doing pairs of channels starting with
the band entry frequency. Trouble is, a lot of the rules start way off at 5120MHz,
which isn't a valid 5GHz channel. Then, eg for HT40U, it would populate:
* (5120,5140)
* (5160,5180)
* (5200,5220)
* (5240,5260)
.. as the HT40U pairs, with the first being the primary channel. Channel 36
is 5180MHz, and since it's not a primary channel here, it wouldn't populate it.
Then, the next HT40U would be 5200/5220, which is highly wrong.
HT40D had the same problem.
So, this just forces that 5GHz HT40 channels start at channel 36 (5180),
no matter what the band edge says. This includes eg doing 4.9GHz channels.
This erm, meant that the HT40 channels for the low band was always wrong.
Oops!
Tested:
* AR9380, STA mode
* AR9344 SoC, AP mode
MFC after: 1 week
* change the HT_RC_2_MCS to do MCS0..23
* Use it when looking up the ht20/ht40 array for bits-per-symbol
* add a clk_to_psec (picoseconds) routine, so we can get sub-microsecond
accuracy for the math
* .. and make that + clk_to_usec public, so higher layer code that is
returning clocks (eg the ANI diag routines, some upcoming locationing
experiments) can be converted to microseconds.
Whilst here, add a comment in ar5416 so i or someone else can revisit the
latency values.
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
The pre-11n calculations include SIFS, but the 11n ones don't.
The reason is that (mostly) the 11n hardware is doing the SIFS calculation
for us but the pre-11n hardware isn't. This means that we're over-shooting
the times in the duration field for non-11n frames on 11n hardware, which
is OK, if not a little inefficient.
Now, this is all fine for what the hardware needs for doing duration math
for ACK, RTS/CTS, frame length, etc, but it isn't useful for doing PHY
duration calculations. Ie, given a frame to TX and its timestamp, what
would the end of the actual transmission time be; and similar for an
RX timestamp and figuring out its original length.
So, this adds a new field to the duration routines which requests
SIFS or no SIFS to be included. All the callers currently will call
it requesting SIFS, so this /should/ be a glorious no-op. I'm however
planning some future work around airtime fairness and positioning which
requires these routines to have SIFS be optional.
Notably though, the 11n version doesn't do any SIFS addition at the moment.
I'll go and tweak and verify all of the packet durations before I go and
flip that part on.
Tested:
* AR9330, STA mode
* AR9330, AP mode
* AR9380, STA mode
* the code already stored the length of the RX desc, which I never used.
So, use that and retire the new flag I introduced a while ago.
* Introduce a TX timestamp length field and capability.
* extend the TX timestamp to 32 bits, as the AR5416 and later does a full
32 bit TX timestamp instead of 15 or 16 bits.
* add RX descriptor fields for PHY uploaded information (coming soon)
* add flags for RX/TX fast timestamp, hardware upload, etc
* add a flag for TX to request ToD/ToA location information.
The legacy bits are just from ah.h; the MCI bits are from the ar9300
HAL "freebsd" extras.
A subsequent commit will include ah_btcoex.h into ah.h and remove
the older defintions.
Split getchannels() method in ath_hal/ah_regdomain.c into a subset
of functions for better readability.
Note: due to different internal structure, it cannot use
ieee80211_add_channel*() (however, some parts are done in a
similar manner).
Differential Revision: https://reviews.freebsd.org/D6139
The synth programming here requires the real centre frequency,
which for HT20 channels is the normal channel, but HT40 is
/not/ the primary channel. Everything else was using 'freq',
which is the correct centre frequency, but the hornet config
was using 'ichan' to do the lookup which was also the primary
channel.
So, modify the HAL call that does the mapping to take a frequency
in MHz and return the channel number.
Tested:
* Carambola 2, AR9331, tested both HT/20 and HT/40 operation.
This probe/attaches correctly in my local branch and now displays
a useful message:
ath0: <Qualcomm Atheros QCA953x> at mem 0x18100000-0x1811ffff irq 0 on nexus0
...
ath0: AR9530 mac 1280.0 RF5110 phy 0.0
Right now the only way to force a cold reset is:
* The HAL itself detects it's needed, or
* The sysctl, setting all resets to be cold.
Trouble is, cold resets take quite a bit longer than warm resets.
However, there are situations where a cold reset would be nice.
Specifically, after a stuck beacon, BB/MAC hang, stuck calibration results,
etc.
The vendor HAL has a separate method to set the reset reason (which is
how HAL_RESET_BBPANIC gets set) which informs the HAL during the reset path
why it occured. This is almost but not quite the same; I may eventually
unify both approaches in the future.
This commit just extends HAL_RESET_TYPE to include both status (eg BBPANIC)
and type (eg do COLD.) None of the HAL code uses it yet though; that'll
come later.
It also is a big no-op in each HAL - I need to go teach each of the HALs
about cold/warm reset through this path.
This was off because the net80211 aggregation code was using the same
state pointers for both fast frames and ampdu tx support which led to some
pretty unfortunate panic-y behaviour.
Now that net80211 doesn't panic, let's flip this back on.
It doesn't (yet) do the horrific sounding thing of A-MPDU aggregates
of fast frames; that'll come next. It's a pre-requisite to supporting
AMSDU + AMPDU anyway, which actually speeds things up quite considerably
(think packing lots of little ACK frames into a single AMSDU.)
Tested:
* QCA955x SoC, AP mode
* AR5416, STA mode
* AR9170, STA mode (with local fast frame patches)
I .. stupidly added code to return HAL_ANI_STATS to HAL_DIAG_ANI_STATS.
I discovered this in a noisy environment when the returned values were
enough to .. well, make everything terrible.
So - restore functionality.
Tested:
* AR5416 (uses the AR5212 HAL), in a /very/ noisy 2GHz environment.
Enough to trigger ANI to get upset and generate useful data.
the top-level HAL.
The athstats program is blindly using a copy of the ar5212 ANI stats structure
to pull out ANI statistics/state and this is problematic for the AR9300
HAL.
So:
* Define HAL_ANI_STATS and HAL_ANI_STATE
* Use HAL_ANI_STATS inside the AR5212 HAL
This commit doesn't (yet) convert the ar5212AniState -> HAL_ANI_STATE when
exporting it to userland; that'll come in the next commit.
rathe than private in each HAL module.
Whilst here, modify ath_hal_private to always have the per-channel
noisefloor stats, rather than conditionally. This just makes
life easier in general (no strange ABI differences between different
HAL compile options.)
Add a couple of methods (clear/reset, add) rather than using
hand-rolled versions of things.
