Reviewed by: Luoqi Chen <luoqi@watermarkgroup.com>
Fixed problem where write()s can get lost due to buffers flagged B_DELWRI
being improperly released in brelse().
The last consumer of this code (the old SCSI system) has left us and
the CAM code does it's own bouncing. The isa dma system has been
doing it's own bouncing for a while too.
Reviewed by: core
the OpenBSD group to fix a problem with the default ifmedia not being
set properly in some cases with a 3c905B, leading to a panic in ifmedia_set().
Also apply a patch to force the transmit start routine to check the
transmitter to make sure it isn't wedged if the outbound tx queue appears
full. This seems to cure some problems with 'watchdog timeout' errors
cropping up in some cases. I tried to do this before by checking for the
IFF_OACTIVE flag on entry to xl_start(), but if the IFF_OACTIVE flag is
set, ether_output() won't even call xl_start(). It should work now.
Lastly, increase the size of the TX queue from 10 descriptors to 16 to
hopefully make it less likely that the TX queue will fill up.
may insert into the list of loaded libraries (ours is one) instead of
appending to the end of the list. Also cope with dlclose() removing
libraries from the list.
string. From the submitted patch:
Credit for patch: Chris Torek <torek@bsdi.com>
Tod Miller <millert@openbsd.org>
This makes us in line with SunOS 4.1.3_U1, Solaris 2.6, OpenBSD 2.3,
HP-UX 10.20, Irix 5.3. The previous behavior was in line with Ultrix 4.4.
PR: bin/7970
Submitted by: Niall Smart nialls@euristix.ie
- Tagged devices were limited to one transaction (oops)
- We revert to untagged with a tag delay if the user changed the
transfer negotiation values (via perhaps camcontrol some day).
- xpt_async did not use the expanded path in some cases which could
cause a panic.
computer 'suspended', although the slot was powered off. There was a
race where the slow could be powered off *after* it was assigned a
new driver when the computer was 'resumed'.
Noticed by: Brian Somers <brian@Awfulhak.org>
PHYs in tl_attach(). This is mainly to suck away any possible stray
interrupts.
This prevents an intermittent problem on some systems where the adapter
probes correctly but yields a device timeout (and possible subsequent adapter
check) when configured. When I originally tested the driver, I ifconfig'ed
the interface after the system had already been booted and didn't notice
any problems, but when configuring the interface immediately at startup,
it would occasionally timeout and hang, until an adapter check interrupt
came along and reset things again. I'm not exactly sure if this is a
general problem of just something peculiar to this hardware (there are
three devices, including the tlan, all on IRQ 11) but the extra reset
shouldn't hurt anything. (It works fine with my 100Mbps Olicom adapter too.)
Thanks to Mark Taylor from Cybernet (mtaylor@cybernet.com) for allowing
me remote access to a Compaq system for debugging purposes.
Submitted by: Kirk McKusick <mckusick@McKusick.COM>
Two minor changes are also included,
1. Remove gratuitious checks for error return from vn_lock with LK_RETRY set,
vn_lock should always succeed in these cases.
2. Back out change rev. 1.36->1.37, which unnecessarily makes async mount
a little more unstable. It also keeps us in sync with other BSDs.
Suggested by: Bruce Evans <bde@zeta.org.au>
Now supposedly less harmful way of accessing VGA sequencer registers
is default. An alternative, often troublesome, I/O access is optional.
Discussed with: sos, jkh
address for the LCA PCI configuration register address.
FreeBSD/Alpha now boots on the NoName (aka AXPpci 33, Alpha PC), and probably
also on the Multia (mine hasn't arrived yet, so I can't tell for sure).
Submitted by: Doug Rabson <dfr@freebsd.org>
