d/freebsd-dev
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
4bca277bd3
freebsd-dev/sys/pci/if_xl.c
Bill Paul e4cffe95c7 Support for large frames for VLANs was added by tweaking the packet size 
register, present only on 3c90xB and later NICs. This meant that you could
not use a 1500 byte MTU with VLANs on original 3c905/3c900 cards (boomerang
chipset). The boomerang chip does support large frames though, just not
in the same way: you can set the 'allow large frames' bit in the MAC
control register to receive frames up to 4K in size.

Changes:

- Set the 'allow large frames' bit for boomerang chips and increase
  the packet size register for cyclone and later chips. This allows
  us to use IFCAP_VLAN_MTU on all supported xl(4) NICs.
- Actually set the IFCAP_VLAN_MTU flag in the capabilities word
  in xl_attach().
- Change the method used to detect older boomerang chips. My 3c575C
  cardbus NIC was being incorrectly identified as 3c90x chip instead
  of 3c90xB because the capabilities word in its EEPROM reports
  a bizzare value. In addition to checking for the supportsNoTxLength
  bit, also check for the absence of the supportsLargePackets bit.
  Both of these cases denote a 3c90xB chip.
- Make RX and TX checksums configurable via the SIOCSIFCAP ioctl.
- Avoid an unecessary le32toh() in xl_rxeof(): we already have the
  received frame size in the lower 16 bits of rxstat, no need to
  read it again.

Tested with 3c905-TX, 3c900-TPO, 3c980C and 3c575C NICs.
2003-07-10 05:24:33 +00:00

3324 lines
85 KiB
C
Raw Blame History

/*
* Copyright (c) 1997, 1998, 1999
* Bill Paul <wpaul@ctr.columbia.edu>. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. All advertising materials mentioning features or use of this software
* must display the following acknowledgement:
* This product includes software developed by Bill Paul.
* 4. Neither the name of the author nor the names of any co-contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD
* BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
* THE POSSIBILITY OF SUCH DAMAGE.
*/
/*
* 3Com 3c90x Etherlink XL PCI NIC driver
*
* Supports the 3Com "boomerang", "cyclone" and "hurricane" PCI
* bus-master chips (3c90x cards and embedded controllers) including
* the following:
*
* 3Com 3c900-TPO 10Mbps/RJ-45
* 3Com 3c900-COMBO 10Mbps/RJ-45,AUI,BNC
* 3Com 3c905-TX 10/100Mbps/RJ-45
* 3Com 3c905-T4 10/100Mbps/RJ-45
* 3Com 3c900B-TPO 10Mbps/RJ-45
* 3Com 3c900B-COMBO 10Mbps/RJ-45,AUI,BNC
* 3Com 3c900B-TPC 10Mbps/RJ-45,BNC
* 3Com 3c900B-FL 10Mbps/Fiber-optic
* 3Com 3c905B-COMBO 10/100Mbps/RJ-45,AUI,BNC
* 3Com 3c905B-TX 10/100Mbps/RJ-45
* 3Com 3c905B-FL/FX 10/100Mbps/Fiber-optic
* 3Com 3c905C-TX 10/100Mbps/RJ-45 (Tornado ASIC)
* 3Com 3c980-TX 10/100Mbps server adapter (Hurricane ASIC)
* 3Com 3c980C-TX 10/100Mbps server adapter (Tornado ASIC)
* 3Com 3cSOHO100-TX 10/100Mbps/RJ-45 (Hurricane ASIC)
* 3Com 3c450-TX 10/100Mbps/RJ-45 (Tornado ASIC)
* 3Com 3c555 10/100Mbps/RJ-45 (MiniPCI, Laptop Hurricane)
* 3Com 3c556 10/100Mbps/RJ-45 (MiniPCI, Hurricane ASIC)
* 3Com 3c556B 10/100Mbps/RJ-45 (MiniPCI, Hurricane ASIC)
* 3Com 3c575TX 10/100Mbps/RJ-45 (Cardbus, Hurricane ASIC)
* 3Com 3c575B 10/100Mbps/RJ-45 (Cardbus, Hurricane ASIC)
* 3Com 3c575C 10/100Mbps/RJ-45 (Cardbus, Hurricane ASIC)
* 3Com 3cxfem656 10/100Mbps/RJ-45 (Cardbus, Hurricane ASIC)
* 3Com 3cxfem656b 10/100Mbps/RJ-45 (Cardbus, Hurricane ASIC)
* 3Com 3cxfem656c 10/100Mbps/RJ-45 (Cardbus, Tornado ASIC)
* Dell Optiplex GX1 on-board 3c918 10/100Mbps/RJ-45
* Dell on-board 3c920 10/100Mbps/RJ-45
* Dell Precision on-board 3c905B 10/100Mbps/RJ-45
* Dell Latitude laptop docking station embedded 3c905-TX
*
* Written by Bill Paul <wpaul@ctr.columbia.edu>
* Electrical Engineering Department
* Columbia University, New York City
*/
/*
* The 3c90x series chips use a bus-master DMA interface for transfering
* packets to and from the controller chip. Some of the "vortex" cards
* (3c59x) also supported a bus master mode, however for those chips
* you could only DMA packets to/from a contiguous memory buffer. For
* transmission this would mean copying the contents of the queued mbuf
* chain into an mbuf cluster and then DMAing the cluster. This extra
* copy would sort of defeat the purpose of the bus master support for
* any packet that doesn't fit into a single mbuf.
*
* By contrast, the 3c90x cards support a fragment-based bus master
* mode where mbuf chains can be encapsulated using TX descriptors.
* This is similar to other PCI chips such as the Texas Instruments
* ThunderLAN and the Intel 82557/82558.
*
* The "vortex" driver (if_vx.c) happens to work for the "boomerang"
* bus master chips because they maintain the old PIO interface for
* backwards compatibility, but starting with the 3c905B and the
* "cyclone" chips, the compatibility interface has been dropped.
* Since using bus master DMA is a big win, we use this driver to
* support the PCI "boomerang" chips even though they work with the
* "vortex" driver in order to obtain better performance.
*
* This driver is in the /sys/pci directory because it only supports
* PCI-based NICs.
*/
#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/sockio.h>
#include <sys/endian.h>
#include <sys/mbuf.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <net/if.h>
#include <net/if_arp.h>
#include <net/ethernet.h>
#include <net/if_dl.h>
#include <net/if_media.h>
#include <net/bpf.h>
#include <machine/bus_memio.h>
#include <machine/bus_pio.h>
#include <machine/bus.h>
#include <machine/resource.h>
#include <sys/bus.h>
#include <sys/rman.h>
#include <dev/mii/mii.h>
#include <dev/mii/miivar.h>
#include <pci/pcireg.h>
#include <pci/pcivar.h>
MODULE_DEPEND(xl, pci, 1, 1, 1);
MODULE_DEPEND(xl, ether, 1, 1, 1);
MODULE_DEPEND(xl, miibus, 1, 1, 1);
/* "controller miibus0" required. See GENERIC if you get errors here. */
#include "miibus_if.h"
#include <pci/if_xlreg.h>
#define XL905B_CSUM_FEATURES (CSUM_IP | CSUM_TCP | CSUM_UDP)
/*
* Various supported device vendors/types and their names.
*/
static struct xl_type xl_devs[] = {
{ TC_VENDORID, TC_DEVICEID_BOOMERANG_10BT,
"3Com 3c900-TPO Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_BOOMERANG_10BT_COMBO,
"3Com 3c900-COMBO Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_BOOMERANG_10_100BT,
"3Com 3c905-TX Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_BOOMERANG_100BT4,
"3Com 3c905-T4 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_KRAKATOA_10BT,
"3Com 3c900B-TPO Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_KRAKATOA_10BT_COMBO,
"3Com 3c900B-COMBO Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_KRAKATOA_10BT_TPC,
"3Com 3c900B-TPC Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_CYCLONE_10FL,
"3Com 3c900B-FL Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_10_100BT,
"3Com 3c905B-TX Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_CYCLONE_10_100BT4,
"3Com 3c905B-T4 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_CYCLONE_10_100FX,
"3Com 3c905B-FX/SC Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_CYCLONE_10_100_COMBO,
"3Com 3c905B-COMBO Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_TORNADO_10_100BT,
"3Com 3c905C-TX Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_TORNADO_10_100BT_920B,
"3Com 3c920B-EMB Integrated Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_10_100BT_SERV,
"3Com 3c980 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_TORNADO_10_100BT_SERV,
"3Com 3c980C Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_SOHO100TX,
"3Com 3cSOHO100-TX OfficeConnect" },
{ TC_VENDORID, TC_DEVICEID_TORNADO_HOMECONNECT,
"3Com 3c450-TX HomeConnect" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_555,
"3Com 3c555 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_556,
"3Com 3c556 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_556B,
"3Com 3c556B Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_575A,
"3Com 3c575TX Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_575B,
"3Com 3c575B Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_575C,
"3Com 3c575C Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_656,
"3Com 3c656 Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_HURRICANE_656B,
"3Com 3c656B Fast Etherlink XL" },
{ TC_VENDORID, TC_DEVICEID_TORNADO_656C,
"3Com 3c656C Fast Etherlink XL" },
{ 0, 0, NULL }
};
static int xl_probe (device_t);
static int xl_attach (device_t);
static int xl_detach (device_t);
static int xl_newbuf (struct xl_softc *, struct xl_chain_onefrag *);
static void xl_stats_update (void *);
static int xl_encap (struct xl_softc *, struct xl_chain *,
struct mbuf *);
static void xl_rxeof (struct xl_softc *);
static int xl_rx_resync (struct xl_softc *);
static void xl_txeof (struct xl_softc *);
static void xl_txeof_90xB (struct xl_softc *);
static void xl_txeoc (struct xl_softc *);
static void xl_intr (void *);
static void xl_start (struct ifnet *);
static void xl_start_90xB (struct ifnet *);
static int xl_ioctl (struct ifnet *, u_long, caddr_t);
static void xl_init (void *);
static void xl_stop (struct xl_softc *);
static void xl_watchdog (struct ifnet *);
static void xl_shutdown (device_t);
static int xl_suspend (device_t);
static int xl_resume (device_t);
static int xl_ifmedia_upd (struct ifnet *);
static void xl_ifmedia_sts (struct ifnet *, struct ifmediareq *);
static int xl_eeprom_wait (struct xl_softc *);
static int xl_read_eeprom (struct xl_softc *, caddr_t, int, int, int);
static void xl_mii_sync (struct xl_softc *);
static void xl_mii_send (struct xl_softc *, u_int32_t, int);
static int xl_mii_readreg (struct xl_softc *, struct xl_mii_frame *);
static int xl_mii_writereg (struct xl_softc *, struct xl_mii_frame *);
static void xl_setcfg (struct xl_softc *);
static void xl_setmode (struct xl_softc *, int);
static u_int8_t xl_calchash (caddr_t);
static void xl_setmulti (struct xl_softc *);
static void xl_setmulti_hash (struct xl_softc *);
static void xl_reset (struct xl_softc *);
static int xl_list_rx_init (struct xl_softc *);
static int xl_list_tx_init (struct xl_softc *);
static int xl_list_tx_init_90xB (struct xl_softc *);
static void xl_wait (struct xl_softc *);
static void xl_mediacheck (struct xl_softc *);
static void xl_choose_xcvr (struct xl_softc *, int);
static void xl_dma_map_addr (void *, bus_dma_segment_t *, int, int);
static void xl_dma_map_rxbuf (void *, bus_dma_segment_t *, int, bus_size_t,
int);
static void xl_dma_map_txbuf (void *, bus_dma_segment_t *, int, bus_size_t,
int);
#ifdef notdef
static void xl_testpacket (struct xl_softc *);
#endif
static int xl_miibus_readreg (device_t, int, int);
static int xl_miibus_writereg (device_t, int, int, int);
static void xl_miibus_statchg (device_t);
static void xl_miibus_mediainit (device_t);
static device_method_t xl_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, xl_probe),
DEVMETHOD(device_attach, xl_attach),
DEVMETHOD(device_detach, xl_detach),
DEVMETHOD(device_shutdown, xl_shutdown),
DEVMETHOD(device_suspend, xl_suspend),
DEVMETHOD(device_resume, xl_resume),
/* bus interface */
DEVMETHOD(bus_print_child, bus_generic_print_child),
DEVMETHOD(bus_driver_added, bus_generic_driver_added),
/* MII interface */
DEVMETHOD(miibus_readreg, xl_miibus_readreg),
DEVMETHOD(miibus_writereg, xl_miibus_writereg),
DEVMETHOD(miibus_statchg, xl_miibus_statchg),
DEVMETHOD(miibus_mediainit, xl_miibus_mediainit),
{ 0, 0 }
};
static driver_t xl_driver = {
"xl",
xl_methods,
sizeof(struct xl_softc)
};
static devclass_t xl_devclass;
DRIVER_MODULE(xl, cardbus, xl_driver, xl_devclass, 0, 0);
DRIVER_MODULE(xl, pci, xl_driver, xl_devclass, 0, 0);
DRIVER_MODULE(miibus, xl, miibus_driver, miibus_devclass, 0, 0);
static void
xl_dma_map_addr(arg, segs, nseg, error)
void *arg;
bus_dma_segment_t *segs;
int nseg, error;
{
u_int32_t *paddr;
paddr = arg;
*paddr = segs->ds_addr;
}
static void
xl_dma_map_rxbuf(arg, segs, nseg, mapsize, error)
void *arg;
bus_dma_segment_t *segs;
int nseg;
bus_size_t mapsize;
int error;
{
u_int32_t *paddr;
if (error)
return;
KASSERT(nseg == 1, ("xl_dma_map_rxbuf: too many DMA segments"));
paddr = arg;
*paddr = segs->ds_addr;
}
static void
xl_dma_map_txbuf(arg, segs, nseg, mapsize, error)
void *arg;
bus_dma_segment_t *segs;
int nseg;
bus_size_t mapsize;
int error;
{
struct xl_list *l;
int i, total_len;
if (error)
return;
KASSERT(nseg <= XL_MAXFRAGS, ("too many DMA segments"));
total_len = 0;
l = arg;
for (i = 0; i < nseg; i++) {
KASSERT(segs[i].ds_len <= MCLBYTES, ("segment size too large"));
l->xl_frag[i].xl_addr = htole32(segs[i].ds_addr);
l->xl_frag[i].xl_len = htole32(segs[i].ds_len);
total_len += segs[i].ds_len;
}
l->xl_frag[nseg - 1].xl_len = htole32(segs[nseg - 1].ds_len |
XL_LAST_FRAG);
l->xl_status = htole32(total_len);
l->xl_next = 0;
}
/*
* Murphy's law says that it's possible the chip can wedge and
* the 'command in progress' bit may never clear. Hence, we wait
* only a finite amount of time to avoid getting caught in an
* infinite loop. Normally this delay routine would be a macro,
* but it isn't called during normal operation so we can afford
* to make it a function.
*/
static void
xl_wait(sc)
struct xl_softc *sc;
{
register int i;
for (i = 0; i < XL_TIMEOUT; i++) {
if (!(CSR_READ_2(sc, XL_STATUS) & XL_STAT_CMDBUSY))
break;
}
if (i == XL_TIMEOUT)
printf("xl%d: command never completed!\n", sc->xl_unit);
return;
}
/*
* MII access routines are provided for adapters with external
* PHYs (3c905-TX, 3c905-T4, 3c905B-T4) and those with built-in
* autoneg logic that's faked up to look like a PHY (3c905B-TX).
* Note: if you don't perform the MDIO operations just right,
* it's possible to end up with code that works correctly with
* some chips/CPUs/processor speeds/bus speeds/etc but not
* with others.
*/
#define MII_SET(x) \
CSR_WRITE_2(sc, XL_W4_PHY_MGMT, \
CSR_READ_2(sc, XL_W4_PHY_MGMT) | (x))
#define MII_CLR(x) \
CSR_WRITE_2(sc, XL_W4_PHY_MGMT, \
CSR_READ_2(sc, XL_W4_PHY_MGMT) & ~(x))
/*
* Sync the PHYs by setting data bit and strobing the clock 32 times.
*/
static void
xl_mii_sync(sc)
struct xl_softc *sc;
{
register int i;
XL_SEL_WIN(4);
MII_SET(XL_MII_DIR|XL_MII_DATA);
for (i = 0; i < 32; i++) {
MII_SET(XL_MII_CLK);
MII_SET(XL_MII_DATA);
MII_CLR(XL_MII_CLK);
MII_SET(XL_MII_DATA);
}
return;
}
/*
* Clock a series of bits through the MII.
*/
static void
xl_mii_send(sc, bits, cnt)
struct xl_softc *sc;
u_int32_t bits;
int cnt;
{
int i;
XL_SEL_WIN(4);
MII_CLR(XL_MII_CLK);
for (i = (0x1 << (cnt - 1)); i; i >>= 1) {
if (bits & i) {
MII_SET(XL_MII_DATA);
} else {
MII_CLR(XL_MII_DATA);
}
MII_CLR(XL_MII_CLK);
MII_SET(XL_MII_CLK);
}
}
/*
* Read an PHY register through the MII.
*/
static int
xl_mii_readreg(sc, frame)
struct xl_softc *sc;
struct xl_mii_frame *frame;
{
int i, ack;
XL_LOCK(sc);
/*
* Set up frame for RX.
*/
frame->mii_stdelim = XL_MII_STARTDELIM;
frame->mii_opcode = XL_MII_READOP;
frame->mii_turnaround = 0;
frame->mii_data = 0;
/*
* Select register window 4.
*/
XL_SEL_WIN(4);
CSR_WRITE_2(sc, XL_W4_PHY_MGMT, 0);
/*
* Turn on data xmit.
*/
MII_SET(XL_MII_DIR);
xl_mii_sync(sc);
/*
* Send command/address info.
*/
xl_mii_send(sc, frame->mii_stdelim, 2);
xl_mii_send(sc, frame->mii_opcode, 2);
xl_mii_send(sc, frame->mii_phyaddr, 5);
xl_mii_send(sc, frame->mii_regaddr, 5);
/* Idle bit */
MII_CLR((XL_MII_CLK|XL_MII_DATA));
MII_SET(XL_MII_CLK);
/* Turn off xmit. */
MII_CLR(XL_MII_DIR);
/* Check for ack */
MII_CLR(XL_MII_CLK);
ack = CSR_READ_2(sc, XL_W4_PHY_MGMT) & XL_MII_DATA;
MII_SET(XL_MII_CLK);
/*
* Now try reading data bits. If the ack failed, we still
* need to clock through 16 cycles to keep the PHY(s) in sync.
*/
if (ack) {
for(i = 0; i < 16; i++) {
MII_CLR(XL_MII_CLK);
MII_SET(XL_MII_CLK);
}
goto fail;
}
for (i = 0x8000; i; i >>= 1) {
MII_CLR(XL_MII_CLK);
if (!ack) {
if (CSR_READ_2(sc, XL_W4_PHY_MGMT) & XL_MII_DATA)
frame->mii_data |= i;
}
MII_SET(XL_MII_CLK);
}
fail:
MII_CLR(XL_MII_CLK);
MII_SET(XL_MII_CLK);
XL_UNLOCK(sc);
if (ack)
return(1);
return(0);
}
/*
* Write to a PHY register through the MII.
*/
static int
xl_mii_writereg(sc, frame)
struct xl_softc *sc;
struct xl_mii_frame *frame;
{
XL_LOCK(sc);
/*
* Set up frame for TX.
*/
frame->mii_stdelim = XL_MII_STARTDELIM;
frame->mii_opcode = XL_MII_WRITEOP;
frame->mii_turnaround = XL_MII_TURNAROUND;
/*
* Select the window 4.
*/
XL_SEL_WIN(4);
/*
* Turn on data output.
*/
MII_SET(XL_MII_DIR);
xl_mii_sync(sc);
xl_mii_send(sc, frame->mii_stdelim, 2);
xl_mii_send(sc, frame->mii_opcode, 2);
xl_mii_send(sc, frame->mii_phyaddr, 5);
xl_mii_send(sc, frame->mii_regaddr, 5);
xl_mii_send(sc, frame->mii_turnaround, 2);
xl_mii_send(sc, frame->mii_data, 16);
/* Idle bit. */
MII_SET(XL_MII_CLK);
MII_CLR(XL_MII_CLK);
/*
* Turn off xmit.
*/
MII_CLR(XL_MII_DIR);
XL_UNLOCK(sc);
return(0);
}
static int
xl_miibus_readreg(dev, phy, reg)
device_t dev;
int phy, reg;
{
struct xl_softc *sc;
struct xl_mii_frame frame;
sc = device_get_softc(dev);
/*
* Pretend that PHYs are only available at MII address 24.
* This is to guard against problems with certain 3Com ASIC
* revisions that incorrectly map the internal transceiver
* control registers at all MII addresses. This can cause
* the miibus code to attach the same PHY several times over.
*/
if ((!(sc->xl_flags & XL_FLAG_PHYOK)) && phy != 24)
return(0);
bzero((char *)&frame, sizeof(frame));
frame.mii_phyaddr = phy;
frame.mii_regaddr = reg;
xl_mii_readreg(sc, &frame);
return(frame.mii_data);
}
static int
xl_miibus_writereg(dev, phy, reg, data)
device_t dev;
int phy, reg, data;
{
struct xl_softc *sc;
struct xl_mii_frame frame;
sc = device_get_softc(dev);
if ((!(sc->xl_flags & XL_FLAG_PHYOK)) && phy != 24)
return(0);
bzero((char *)&frame, sizeof(frame));
frame.mii_phyaddr = phy;
frame.mii_regaddr = reg;
frame.mii_data = data;
xl_mii_writereg(sc, &frame);
return(0);
}
static void
xl_miibus_statchg(dev)
device_t dev;
{
struct xl_softc *sc;
struct mii_data *mii;
sc = device_get_softc(dev);
mii = device_get_softc(sc->xl_miibus);
XL_LOCK(sc);
xl_setcfg(sc);
/* Set ASIC's duplex mode to match the PHY. */
XL_SEL_WIN(3);
if ((mii->mii_media_active & IFM_GMASK) == IFM_FDX)
CSR_WRITE_1(sc, XL_W3_MAC_CTRL, XL_MACCTRL_DUPLEX);
else
CSR_WRITE_1(sc, XL_W3_MAC_CTRL,
(CSR_READ_1(sc, XL_W3_MAC_CTRL) & ~XL_MACCTRL_DUPLEX));
XL_UNLOCK(sc);
return;
}
/*
* Special support for the 3c905B-COMBO. This card has 10/100 support
* plus BNC and AUI ports. This means we will have both an miibus attached
* plus some non-MII media settings. In order to allow this, we have to
* add the extra media to the miibus's ifmedia struct, but we can't do
* that during xl_attach() because the miibus hasn't been attached yet.
* So instead, we wait until the miibus probe/attach is done, at which
* point we will get a callback telling is that it's safe to add our
* extra media.
*/
static void
xl_miibus_mediainit(dev)
device_t dev;
{
struct xl_softc *sc;
struct mii_data *mii;
struct ifmedia *ifm;
sc = device_get_softc(dev);
mii = device_get_softc(sc->xl_miibus);
ifm = &mii->mii_media;
XL_LOCK(sc);
if (sc->xl_media & (XL_MEDIAOPT_AUI|XL_MEDIAOPT_10FL)) {
/*
* Check for a 10baseFL board in disguise.
*/
if (sc->xl_type == XL_TYPE_905B &&
sc->xl_media == XL_MEDIAOPT_10FL) {
if (bootverbose)
printf("xl%d: found 10baseFL\n", sc->xl_unit);
ifmedia_add(ifm, IFM_ETHER|IFM_10_FL, 0, NULL);
ifmedia_add(ifm, IFM_ETHER|IFM_10_FL|IFM_HDX, 0, NULL);
if (sc->xl_caps & XL_CAPS_FULL_DUPLEX)
ifmedia_add(ifm,
IFM_ETHER|IFM_10_FL|IFM_FDX, 0, NULL);
} else {
if (bootverbose)
printf("xl%d: found AUI\n", sc->xl_unit);
ifmedia_add(ifm, IFM_ETHER|IFM_10_5, 0, NULL);
}
}
if (sc->xl_media & XL_MEDIAOPT_BNC) {
if (bootverbose)
printf("xl%d: found BNC\n", sc->xl_unit);
ifmedia_add(ifm, IFM_ETHER|IFM_10_2, 0, NULL);
}
XL_UNLOCK(sc);
return;
}
/*
* The EEPROM is slow: give it time to come ready after issuing
* it a command.
*/
static int
xl_eeprom_wait(sc)
struct xl_softc *sc;
{
int i;
for (i = 0; i < 100; i++) {
if (CSR_READ_2(sc, XL_W0_EE_CMD) & XL_EE_BUSY)
DELAY(162);
else
break;
}
if (i == 100) {
printf("xl%d: eeprom failed to come ready\n", sc->xl_unit);
return(1);
}
return(0);
}
/*
* Read a sequence of words from the EEPROM. Note that ethernet address
* data is stored in the EEPROM in network byte order.
*/
static int
xl_read_eeprom(sc, dest, off, cnt, swap)
struct xl_softc *sc;
caddr_t dest;
int off;
int cnt;
int swap;
{
int err = 0, i;
u_int16_t word = 0, *ptr;
#define EEPROM_5BIT_OFFSET(A) ((((A) << 2) & 0x7F00) | ((A) & 0x003F))
#define EEPROM_8BIT_OFFSET(A) ((A) & 0x003F)
/* WARNING! DANGER!
* It's easy to accidentally overwrite the rom content!
* Note: the 3c575 uses 8bit EEPROM offsets.
*/
XL_SEL_WIN(0);
if (xl_eeprom_wait(sc))
return(1);
if (sc->xl_flags & XL_FLAG_EEPROM_OFFSET_30)
off += 0x30;
for (i = 0; i < cnt; i++) {
if (sc->xl_flags & XL_FLAG_8BITROM)
CSR_WRITE_2(sc, XL_W0_EE_CMD,
XL_EE_8BIT_READ | EEPROM_8BIT_OFFSET(off + i));
else
CSR_WRITE_2(sc, XL_W0_EE_CMD,
XL_EE_READ | EEPROM_5BIT_OFFSET(off + i));
err = xl_eeprom_wait(sc);
if (err)
break;
word = CSR_READ_2(sc, XL_W0_EE_DATA);
ptr = (u_int16_t *)(dest + (i * 2));
if (swap)
*ptr = ntohs(word);
else
*ptr = word;
}
return(err ? 1 : 0);
}
/*
* This routine is taken from the 3Com Etherlink XL manual,
* page 10-7. It calculates a CRC of the supplied multicast
* group address and returns the lower 8 bits, which are used
* as the multicast filter position.
* Note: the 3c905B currently only supports a 64-bit hash table,
* which means we really only need 6 bits, but the manual indicates
* that future chip revisions will have a 256-bit hash table,
* hence the routine is set up to calculate 8 bits of position
* info in case we need it some day.
* Note II, The Sequel: _CURRENT_ versions of the 3c905B have a
* 256 bit hash table. This means we have to use all 8 bits regardless.
* On older cards, the upper 2 bits will be ignored. Grrrr....
*/
static u_int8_t xl_calchash(addr)
caddr_t addr;
{
u_int32_t crc, carry;
int i, j;
u_int8_t c;
/* Compute CRC for the address value. */
crc = 0xFFFFFFFF; /* initial value */
for (i = 0; i < 6; i++) {
c = *(addr + i);
for (j = 0; j < 8; j++) {
carry = ((crc & 0x80000000) ? 1 : 0) ^ (c & 0x01);
crc <<= 1;
c >>= 1;
if (carry)
crc = (crc ^ 0x04c11db6) | carry;
}
}
/* return the filter bit position */
return(crc & 0x000000FF);
}
/*
* NICs older than the 3c905B have only one multicast option, which
* is to enable reception of all multicast frames.
*/
static void
xl_setmulti(sc)
struct xl_softc *sc;
{
struct ifnet *ifp;
struct ifmultiaddr *ifma;
u_int8_t rxfilt;
int mcnt = 0;
ifp = &sc->arpcom.ac_if;
XL_SEL_WIN(5);
rxfilt = CSR_READ_1(sc, XL_W5_RX_FILTER);
if (ifp->if_flags & IFF_ALLMULTI) {
rxfilt |= XL_RXFILTER_ALLMULTI;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
return;
}
TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link)
mcnt++;
if (mcnt)
rxfilt |= XL_RXFILTER_ALLMULTI;
else
rxfilt &= ~XL_RXFILTER_ALLMULTI;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
return;
}
/*
* 3c905B adapters have a hash filter that we can program.
*/
static void
xl_setmulti_hash(sc)
struct xl_softc *sc;
{
struct ifnet *ifp;
int h = 0, i;
struct ifmultiaddr *ifma;
u_int8_t rxfilt;
int mcnt = 0;
ifp = &sc->arpcom.ac_if;
XL_SEL_WIN(5);
rxfilt = CSR_READ_1(sc, XL_W5_RX_FILTER);
if (ifp->if_flags & IFF_ALLMULTI) {
rxfilt |= XL_RXFILTER_ALLMULTI;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
return;
} else
rxfilt &= ~XL_RXFILTER_ALLMULTI;
/* first, zot all the existing hash bits */
for (i = 0; i < XL_HASHFILT_SIZE; i++)
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_HASH|i);
/* now program new ones */
TAILQ_FOREACH(ifma, &ifp->if_multiaddrs, ifma_link) {
if (ifma->ifma_addr->sa_family != AF_LINK)
continue;
h = xl_calchash(LLADDR((struct sockaddr_dl *)ifma->ifma_addr));
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_HASH|XL_HASH_SET|h);
mcnt++;
}
if (mcnt)
rxfilt |= XL_RXFILTER_MULTIHASH;
else
rxfilt &= ~XL_RXFILTER_MULTIHASH;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
return;
}
#ifdef notdef
static void
xl_testpacket(sc)
struct xl_softc *sc;
{
struct mbuf *m;
struct ifnet *ifp;
ifp = &sc->arpcom.ac_if;
MGETHDR(m, M_DONTWAIT, MT_DATA);
if (m == NULL)
return;
bcopy(&sc->arpcom.ac_enaddr,
mtod(m, struct ether_header *)->ether_dhost, ETHER_ADDR_LEN);
bcopy(&sc->arpcom.ac_enaddr,
mtod(m, struct ether_header *)->ether_shost, ETHER_ADDR_LEN);
mtod(m, struct ether_header *)->ether_type = htons(3);
mtod(m, unsigned char *)[14] = 0;
mtod(m, unsigned char *)[15] = 0;
mtod(m, unsigned char *)[16] = 0xE3;
m->m_len = m->m_pkthdr.len = sizeof(struct ether_header) + 3;
IF_ENQUEUE(&ifp->if_snd, m);
xl_start(ifp);
return;
}
#endif
static void
xl_setcfg(sc)
struct xl_softc *sc;
{
u_int32_t icfg;
XL_SEL_WIN(3);
icfg = CSR_READ_4(sc, XL_W3_INTERNAL_CFG);
icfg &= ~XL_ICFG_CONNECTOR_MASK;
if (sc->xl_media & XL_MEDIAOPT_MII ||
sc->xl_media & XL_MEDIAOPT_BT4)
icfg |= (XL_XCVR_MII << XL_ICFG_CONNECTOR_BITS);
if (sc->xl_media & XL_MEDIAOPT_BTX)
icfg |= (XL_XCVR_AUTO << XL_ICFG_CONNECTOR_BITS);
CSR_WRITE_4(sc, XL_W3_INTERNAL_CFG, icfg);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_STOP);
return;
}
static void
xl_setmode(sc, media)
struct xl_softc *sc;
int media;
{
u_int32_t icfg;
u_int16_t mediastat;
printf("xl%d: selecting ", sc->xl_unit);
XL_SEL_WIN(4);
mediastat = CSR_READ_2(sc, XL_W4_MEDIA_STATUS);
XL_SEL_WIN(3);
icfg = CSR_READ_4(sc, XL_W3_INTERNAL_CFG);
if (sc->xl_media & XL_MEDIAOPT_BT) {
if (IFM_SUBTYPE(media) == IFM_10_T) {
printf("10baseT transceiver, ");
sc->xl_xcvr = XL_XCVR_10BT;
icfg &= ~XL_ICFG_CONNECTOR_MASK;
icfg |= (XL_XCVR_10BT << XL_ICFG_CONNECTOR_BITS);
mediastat |= XL_MEDIASTAT_LINKBEAT|
XL_MEDIASTAT_JABGUARD;
mediastat &= ~XL_MEDIASTAT_SQEENB;
}
}
if (sc->xl_media & XL_MEDIAOPT_BFX) {
if (IFM_SUBTYPE(media) == IFM_100_FX) {
printf("100baseFX port, ");
sc->xl_xcvr = XL_XCVR_100BFX;
icfg &= ~XL_ICFG_CONNECTOR_MASK;
icfg |= (XL_XCVR_100BFX << XL_ICFG_CONNECTOR_BITS);
mediastat |= XL_MEDIASTAT_LINKBEAT;
mediastat &= ~XL_MEDIASTAT_SQEENB;
}
}
if (sc->xl_media & (XL_MEDIAOPT_AUI|XL_MEDIAOPT_10FL)) {
if (IFM_SUBTYPE(media) == IFM_10_5) {
printf("AUI port, ");
sc->xl_xcvr = XL_XCVR_AUI;
icfg &= ~XL_ICFG_CONNECTOR_MASK;
icfg |= (XL_XCVR_AUI << XL_ICFG_CONNECTOR_BITS);
mediastat &= ~(XL_MEDIASTAT_LINKBEAT|
XL_MEDIASTAT_JABGUARD);
mediastat |= ~XL_MEDIASTAT_SQEENB;
}
if (IFM_SUBTYPE(media) == IFM_10_FL) {
printf("10baseFL transceiver, ");
sc->xl_xcvr = XL_XCVR_AUI;
icfg &= ~XL_ICFG_CONNECTOR_MASK;
icfg |= (XL_XCVR_AUI << XL_ICFG_CONNECTOR_BITS);
mediastat &= ~(XL_MEDIASTAT_LINKBEAT|
XL_MEDIASTAT_JABGUARD);
mediastat |= ~XL_MEDIASTAT_SQEENB;
}
}
if (sc->xl_media & XL_MEDIAOPT_BNC) {
if (IFM_SUBTYPE(media) == IFM_10_2) {
printf("BNC port, ");
sc->xl_xcvr = XL_XCVR_COAX;
icfg &= ~XL_ICFG_CONNECTOR_MASK;
icfg |= (XL_XCVR_COAX << XL_ICFG_CONNECTOR_BITS);
mediastat &= ~(XL_MEDIASTAT_LINKBEAT|
XL_MEDIASTAT_JABGUARD|
XL_MEDIASTAT_SQEENB);
}
}
if ((media & IFM_GMASK) == IFM_FDX ||
IFM_SUBTYPE(media) == IFM_100_FX) {
printf("full duplex\n");
XL_SEL_WIN(3);
CSR_WRITE_1(sc, XL_W3_MAC_CTRL, XL_MACCTRL_DUPLEX);
} else {
printf("half duplex\n");
XL_SEL_WIN(3);
CSR_WRITE_1(sc, XL_W3_MAC_CTRL,
(CSR_READ_1(sc, XL_W3_MAC_CTRL) & ~XL_MACCTRL_DUPLEX));
}
if (IFM_SUBTYPE(media) == IFM_10_2)
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_START);
else
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_STOP);
CSR_WRITE_4(sc, XL_W3_INTERNAL_CFG, icfg);
XL_SEL_WIN(4);
CSR_WRITE_2(sc, XL_W4_MEDIA_STATUS, mediastat);
DELAY(800);
XL_SEL_WIN(7);
return;
}
static void
xl_reset(sc)
struct xl_softc *sc;
{
register int i;
XL_SEL_WIN(0);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RESET |
((sc->xl_flags & XL_FLAG_WEIRDRESET) ?
XL_RESETOPT_DISADVFD:0));
/*
* If we're using memory mapped register mode, pause briefly
* after issuing the reset command before trying to access any
* other registers. With my 3c575C cardbus card, failing to do
* this results in the system locking up while trying to poll
* the command busy bit in the status register.
*/
if (sc->xl_flags & XL_FLAG_USE_MMIO)
DELAY(100000);
for (i = 0; i < XL_TIMEOUT; i++) {
DELAY(10);
if (!(CSR_READ_2(sc, XL_STATUS) & XL_STAT_CMDBUSY))
break;
}
if (i == XL_TIMEOUT)
printf("xl%d: reset didn't complete\n", sc->xl_unit);
/* Reset TX and RX. */
/* Note: the RX reset takes an absurd amount of time
* on newer versions of the Tornado chips such as those
* on the 3c905CX and newer 3c908C cards. We wait an
* extra amount of time so that xl_wait() doesn't complain
* and annoy the users.
*/
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_RESET);
DELAY(100000);
xl_wait(sc);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_RESET);
xl_wait(sc);
if (sc->xl_flags & XL_FLAG_INVERT_LED_PWR ||
sc->xl_flags & XL_FLAG_INVERT_MII_PWR) {
XL_SEL_WIN(2);
CSR_WRITE_2(sc, XL_W2_RESET_OPTIONS, CSR_READ_2(sc,
XL_W2_RESET_OPTIONS)
| ((sc->xl_flags & XL_FLAG_INVERT_LED_PWR)?XL_RESETOPT_INVERT_LED:0)
| ((sc->xl_flags & XL_FLAG_INVERT_MII_PWR)?XL_RESETOPT_INVERT_MII:0)
);
}
/* Wait a little while for the chip to get its brains in order. */
DELAY(100000);
return;
}
/*
* Probe for a 3Com Etherlink XL chip. Check the PCI vendor and device
* IDs against our list and return a device name if we find a match.
*/
static int
xl_probe(dev)
device_t dev;
{
struct xl_type *t;
t = xl_devs;
while(t->xl_name != NULL) {
if ((pci_get_vendor(dev) == t->xl_vid) &&
(pci_get_device(dev) == t->xl_did)) {
device_set_desc(dev, t->xl_name);
return(0);
}
t++;
}
return(ENXIO);
}
/*
* This routine is a kludge to work around possible hardware faults
* or manufacturing defects that can cause the media options register
* (or reset options register, as it's called for the first generation
* 3c90x adapters) to return an incorrect result. I have encountered
* one Dell Latitude laptop docking station with an integrated 3c905-TX
* which doesn't have any of the 'mediaopt' bits set. This screws up
* the attach routine pretty badly because it doesn't know what media
* to look for. If we find ourselves in this predicament, this routine
* will try to guess the media options values and warn the user of a
* possible manufacturing defect with his adapter/system/whatever.
*/
static void
xl_mediacheck(sc)
struct xl_softc *sc;
{
/*
* If some of the media options bits are set, assume they are
* correct. If not, try to figure it out down below.
* XXX I should check for 10baseFL, but I don't have an adapter
* to test with.
*/
if (sc->xl_media & (XL_MEDIAOPT_MASK & ~XL_MEDIAOPT_VCO)) {
/*
* Check the XCVR value. If it's not in the normal range
* of values, we need to fake it up here.
*/
if (sc->xl_xcvr <= XL_XCVR_AUTO)
return;
else {
printf("xl%d: bogus xcvr value "
"in EEPROM (%x)\n", sc->xl_unit, sc->xl_xcvr);
printf("xl%d: choosing new default based "
"on card type\n", sc->xl_unit);
}
} else {
if (sc->xl_type == XL_TYPE_905B &&
sc->xl_media & XL_MEDIAOPT_10FL)
return;
printf("xl%d: WARNING: no media options bits set in "
"the media options register!!\n", sc->xl_unit);
printf("xl%d: this could be a manufacturing defect in "
"your adapter or system\n", sc->xl_unit);
printf("xl%d: attempting to guess media type; you "
"should probably consult your vendor\n", sc->xl_unit);
}
xl_choose_xcvr(sc, 1);
return;
}
static void
xl_choose_xcvr(sc, verbose)
struct xl_softc *sc;
int verbose;
{
u_int16_t devid;
/*
* Read the device ID from the EEPROM.
* This is what's loaded into the PCI device ID register, so it has
* to be correct otherwise we wouldn't have gotten this far.
*/
xl_read_eeprom(sc, (caddr_t)&devid, XL_EE_PRODID, 1, 0);
switch(devid) {
case TC_DEVICEID_BOOMERANG_10BT: /* 3c900-TPO */
case TC_DEVICEID_KRAKATOA_10BT: /* 3c900B-TPO */
sc->xl_media = XL_MEDIAOPT_BT;
sc->xl_xcvr = XL_XCVR_10BT;
if (verbose)
printf("xl%d: guessing 10BaseT "
"transceiver\n", sc->xl_unit);
break;
case TC_DEVICEID_BOOMERANG_10BT_COMBO: /* 3c900-COMBO */
case TC_DEVICEID_KRAKATOA_10BT_COMBO: /* 3c900B-COMBO */
sc->xl_media = XL_MEDIAOPT_BT|XL_MEDIAOPT_BNC|XL_MEDIAOPT_AUI;
sc->xl_xcvr = XL_XCVR_10BT;
if (verbose)
printf("xl%d: guessing COMBO "
"(AUI/BNC/TP)\n", sc->xl_unit);
break;
case TC_DEVICEID_KRAKATOA_10BT_TPC: /* 3c900B-TPC */
sc->xl_media = XL_MEDIAOPT_BT|XL_MEDIAOPT_BNC;
sc->xl_xcvr = XL_XCVR_10BT;
if (verbose)
printf("xl%d: guessing TPC (BNC/TP)\n", sc->xl_unit);
break;
case TC_DEVICEID_CYCLONE_10FL: /* 3c900B-FL */
sc->xl_media = XL_MEDIAOPT_10FL;
sc->xl_xcvr = XL_XCVR_AUI;
if (verbose)
printf("xl%d: guessing 10baseFL\n", sc->xl_unit);
break;
case TC_DEVICEID_BOOMERANG_10_100BT: /* 3c905-TX */
case TC_DEVICEID_HURRICANE_555: /* 3c555 */
case TC_DEVICEID_HURRICANE_556: /* 3c556 */
case TC_DEVICEID_HURRICANE_556B: /* 3c556B */
case TC_DEVICEID_HURRICANE_575A: /* 3c575TX */
case TC_DEVICEID_HURRICANE_575B: /* 3c575B */
case TC_DEVICEID_HURRICANE_575C: /* 3c575C */
case TC_DEVICEID_HURRICANE_656: /* 3c656 */
case TC_DEVICEID_HURRICANE_656B: /* 3c656B */
case TC_DEVICEID_TORNADO_656C: /* 3c656C */
case TC_DEVICEID_TORNADO_10_100BT_920B: /* 3c920B-EMB */
sc->xl_media = XL_MEDIAOPT_MII;
sc->xl_xcvr = XL_XCVR_MII;
if (verbose)
printf("xl%d: guessing MII\n", sc->xl_unit);
break;
case TC_DEVICEID_BOOMERANG_100BT4: /* 3c905-T4 */
case TC_DEVICEID_CYCLONE_10_100BT4: /* 3c905B-T4 */
sc->xl_media = XL_MEDIAOPT_BT4;
sc->xl_xcvr = XL_XCVR_MII;
if (verbose)
printf("xl%d: guessing 100BaseT4/MII\n", sc->xl_unit);
break;
case TC_DEVICEID_HURRICANE_10_100BT: /* 3c905B-TX */
case TC_DEVICEID_HURRICANE_10_100BT_SERV:/*3c980-TX */
case TC_DEVICEID_TORNADO_10_100BT_SERV: /* 3c980C-TX */
case TC_DEVICEID_HURRICANE_SOHO100TX: /* 3cSOHO100-TX */
case TC_DEVICEID_TORNADO_10_100BT: /* 3c905C-TX */
case TC_DEVICEID_TORNADO_HOMECONNECT: /* 3c450-TX */
sc->xl_media = XL_MEDIAOPT_BTX;
sc->xl_xcvr = XL_XCVR_AUTO;
if (verbose)
printf("xl%d: guessing 10/100 internal\n", sc->xl_unit);
break;
case TC_DEVICEID_CYCLONE_10_100_COMBO: /* 3c905B-COMBO */
sc->xl_media = XL_MEDIAOPT_BTX|XL_MEDIAOPT_BNC|XL_MEDIAOPT_AUI;
sc->xl_xcvr = XL_XCVR_AUTO;
if (verbose)
printf("xl%d: guessing 10/100 "
"plus BNC/AUI\n", sc->xl_unit);
break;
default:
printf("xl%d: unknown device ID: %x -- "
"defaulting to 10baseT\n", sc->xl_unit, devid);
sc->xl_media = XL_MEDIAOPT_BT;
break;
}
return;
}
/*
* Attach the interface. Allocate softc structures, do ifmedia
* setup and ethernet/BPF attach.
*/
static int
xl_attach(dev)
device_t dev;
{
u_char eaddr[ETHER_ADDR_LEN];
u_int16_t xcvr[2];
struct xl_softc *sc;
struct ifnet *ifp;
int media = IFM_ETHER|IFM_100_TX|IFM_FDX;
int unit, error = 0, rid, res;
sc = device_get_softc(dev);
unit = device_get_unit(dev);
mtx_init(&sc->xl_mtx, device_get_nameunit(dev), MTX_NETWORK_LOCK,
MTX_DEF | MTX_RECURSE);
ifmedia_init(&sc->ifmedia, 0, xl_ifmedia_upd, xl_ifmedia_sts);
sc->xl_flags = 0;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_555)
sc->xl_flags |= XL_FLAG_EEPROM_OFFSET_30 | XL_FLAG_PHYOK;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_556 ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_556B)
sc->xl_flags |= XL_FLAG_FUNCREG | XL_FLAG_PHYOK |
XL_FLAG_EEPROM_OFFSET_30 | XL_FLAG_WEIRDRESET |
XL_FLAG_INVERT_LED_PWR | XL_FLAG_INVERT_MII_PWR;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_555 ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_556)
sc->xl_flags |= XL_FLAG_8BITROM;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_556B)
sc->xl_flags |= XL_FLAG_NO_XCVR_PWR;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_575A ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_575B ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_575C ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_656B ||
pci_get_device(dev) == TC_DEVICEID_TORNADO_656C)
sc->xl_flags |= XL_FLAG_FUNCREG | XL_FLAG_PHYOK |
XL_FLAG_EEPROM_OFFSET_30 | XL_FLAG_8BITROM;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_656)
sc->xl_flags |= XL_FLAG_FUNCREG | XL_FLAG_PHYOK;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_575B)
sc->xl_flags |= XL_FLAG_INVERT_LED_PWR;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_575C)
sc->xl_flags |= XL_FLAG_INVERT_MII_PWR;
if (pci_get_device(dev) == TC_DEVICEID_TORNADO_656C)
sc->xl_flags |= XL_FLAG_INVERT_MII_PWR;
if (pci_get_device(dev) == TC_DEVICEID_HURRICANE_656 ||
pci_get_device(dev) == TC_DEVICEID_HURRICANE_656B)
sc->xl_flags |= XL_FLAG_INVERT_MII_PWR |
XL_FLAG_INVERT_LED_PWR;
if (pci_get_device(dev) == TC_DEVICEID_TORNADO_10_100BT_920B)
sc->xl_flags |= XL_FLAG_PHYOK;
#ifndef BURN_BRIDGES
/*
* If this is a 3c905B, we have to check one extra thing.
* The 905B supports power management and may be placed in
* a low-power mode (D3 mode), typically by certain operating
* systems which shall not be named. The PCI BIOS is supposed
* to reset the NIC and bring it out of low-power mode, but
* some do not. Consequently, we have to see if this chip
* supports power management, and if so, make sure it's not
* in low-power mode. If power management is available, the
* capid byte will be 0x01.
*
* I _think_ that what actually happens is that the chip
* loses its PCI configuration during the transition from
* D3 back to D0; this means that it should be possible for
* us to save the PCI iobase, membase and IRQ, put the chip
* back in the D0 state, then restore the PCI config ourselves.
*/
if (pci_get_powerstate(dev) != PCI_POWERSTATE_D0) {
u_int32_t iobase, membase, irq;
/* Save important PCI config data. */
iobase = pci_read_config(dev, XL_PCI_LOIO, 4);
membase = pci_read_config(dev, XL_PCI_LOMEM, 4);
irq = pci_read_config(dev, XL_PCI_INTLINE, 4);
/* Reset the power state. */
printf("xl%d: chip is in D%d power mode "
"-- setting to D0\n", unit,
pci_get_powerstate(dev));
pci_set_powerstate(dev, PCI_POWERSTATE_D0);
/* Restore PCI config data. */
pci_write_config(dev, XL_PCI_LOIO, iobase, 4);
pci_write_config(dev, XL_PCI_LOMEM, membase, 4);
pci_write_config(dev, XL_PCI_INTLINE, irq, 4);
}
#endif
/*
* Map control/status registers.
*/
pci_enable_busmaster(dev);
rid = XL_PCI_LOMEM;
res = SYS_RES_MEMORY;
sc->xl_res = bus_alloc_resource(dev, res, &rid,
0, ~0, 1, RF_ACTIVE);
if (sc->xl_res != NULL) {
sc->xl_flags |= XL_FLAG_USE_MMIO;
if (bootverbose)
printf("xl%d: using memory mapped I/O\n", unit);
} else {
rid = XL_PCI_LOIO;
res = SYS_RES_IOPORT;
sc->xl_res = bus_alloc_resource(dev, res, &rid,
0, ~0, 1, RF_ACTIVE);
if (sc->xl_res == NULL) {
printf ("xl%d: couldn't map ports/memory\n", unit);
error = ENXIO;
goto fail;
}
if (bootverbose)
printf("xl%d: using port I/O\n", unit);
}
sc->xl_btag = rman_get_bustag(sc->xl_res);
sc->xl_bhandle = rman_get_bushandle(sc->xl_res);
if (sc->xl_flags & XL_FLAG_FUNCREG) {
rid = XL_PCI_FUNCMEM;
sc->xl_fres = bus_alloc_resource(dev, SYS_RES_MEMORY, &rid,
0, ~0, 1, RF_ACTIVE);
if (sc->xl_fres == NULL) {
printf ("xl%d: couldn't map ports/memory\n", unit);
error = ENXIO;
goto fail;
}
sc->xl_ftag = rman_get_bustag(sc->xl_fres);
sc->xl_fhandle = rman_get_bushandle(sc->xl_fres);
}
/* Allocate interrupt */
rid = 0;
sc->xl_irq = bus_alloc_resource(dev, SYS_RES_IRQ, &rid, 0, ~0, 1,
RF_SHAREABLE | RF_ACTIVE);
if (sc->xl_irq == NULL) {
printf("xl%d: couldn't map interrupt\n", unit);
error = ENXIO;
goto fail;
}
/* Reset the adapter. */
xl_reset(sc);
/*
* Get station address from the EEPROM.
*/
if (xl_read_eeprom(sc, (caddr_t)&eaddr, XL_EE_OEM_ADR0, 3, 1)) {
printf("xl%d: failed to read station address\n", sc->xl_unit);
error = ENXIO;
goto fail;
}
/*
* A 3Com chip was detected. Inform the world.
*/
printf("xl%d: Ethernet address: %6D\n", unit, eaddr, ":");
sc->xl_unit = unit;
callout_handle_init(&sc->xl_stat_ch);
bcopy(eaddr, (char *)&sc->arpcom.ac_enaddr, ETHER_ADDR_LEN);
/*
* Now allocate a tag for the DMA descriptor lists and a chunk
* of DMA-able memory based on the tag. Also obtain the DMA
* addresses of the RX and TX ring, which we'll need later.
* All of our lists are allocated as a contiguous block
* of memory.
*/
error = bus_dma_tag_create(NULL, 8, 0,
BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL,
XL_RX_LIST_SZ, 1, XL_RX_LIST_SZ, 0, NULL, NULL,
&sc->xl_ldata.xl_rx_tag);
if (error) {
printf("xl%d: failed to allocate rx dma tag\n", unit);
goto fail;
}
error = bus_dmamem_alloc(sc->xl_ldata.xl_rx_tag,
(void **)&sc->xl_ldata.xl_rx_list, BUS_DMA_NOWAIT,
&sc->xl_ldata.xl_rx_dmamap);
if (error) {
printf("xl%d: no memory for rx list buffers!\n", unit);
bus_dma_tag_destroy(sc->xl_ldata.xl_rx_tag);
sc->xl_ldata.xl_rx_tag = NULL;
goto fail;
}
error = bus_dmamap_load(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap, sc->xl_ldata.xl_rx_list,
XL_RX_LIST_SZ, xl_dma_map_addr,
&sc->xl_ldata.xl_rx_dmaaddr, BUS_DMA_NOWAIT);
if (error) {
printf("xl%d: cannot get dma address of the rx ring!\n", unit);
bus_dmamem_free(sc->xl_ldata.xl_rx_tag, sc->xl_ldata.xl_rx_list,
sc->xl_ldata.xl_rx_dmamap);
bus_dma_tag_destroy(sc->xl_ldata.xl_rx_tag);
sc->xl_ldata.xl_rx_tag = NULL;
goto fail;
}
error = bus_dma_tag_create(NULL, 8, 0,
BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL,
XL_TX_LIST_SZ, 1, XL_TX_LIST_SZ, 0, NULL, NULL,
&sc->xl_ldata.xl_tx_tag);
if (error) {
printf("xl%d: failed to allocate tx dma tag\n", unit);
goto fail;
}
error = bus_dmamem_alloc(sc->xl_ldata.xl_tx_tag,
(void **)&sc->xl_ldata.xl_tx_list, BUS_DMA_NOWAIT,
&sc->xl_ldata.xl_tx_dmamap);
if (error) {
printf("xl%d: no memory for list buffers!\n", unit);
bus_dma_tag_destroy(sc->xl_ldata.xl_tx_tag);
sc->xl_ldata.xl_tx_tag = NULL;
goto fail;
}
error = bus_dmamap_load(sc->xl_ldata.xl_tx_tag,
sc->xl_ldata.xl_tx_dmamap, sc->xl_ldata.xl_tx_list,
XL_TX_LIST_SZ, xl_dma_map_addr,
&sc->xl_ldata.xl_tx_dmaaddr, BUS_DMA_NOWAIT);
if (error) {
printf("xl%d: cannot get dma address of the tx ring!\n", unit);
bus_dmamem_free(sc->xl_ldata.xl_tx_tag, sc->xl_ldata.xl_tx_list,
sc->xl_ldata.xl_tx_dmamap);
bus_dma_tag_destroy(sc->xl_ldata.xl_tx_tag);
sc->xl_ldata.xl_tx_tag = NULL;
goto fail;
}
/*
* Allocate a DMA tag for the mapping of mbufs.
*/
error = bus_dma_tag_create(NULL, 1, 0,
BUS_SPACE_MAXADDR_32BIT, BUS_SPACE_MAXADDR, NULL, NULL,
MCLBYTES * XL_MAXFRAGS, XL_MAXFRAGS, MCLBYTES, 0, NULL,
NULL, &sc->xl_mtag);
if (error) {
printf("xl%d: failed to allocate mbuf dma tag\n", unit);
goto fail;
}
bzero(sc->xl_ldata.xl_tx_list, XL_TX_LIST_SZ);
bzero(sc->xl_ldata.xl_rx_list, XL_RX_LIST_SZ);
/* We need a spare DMA map for the RX ring. */
error = bus_dmamap_create(sc->xl_mtag, 0, &sc->xl_tmpmap);
if (error)
goto fail;
/*
* Figure out the card type. 3c905B adapters have the
* 'supportsNoTxLength' bit set in the capabilities
* word in the EEPROM.
* Note: my 3c575C cardbus card lies. It returns a value
* of 0x1578 for its capabilities word, which is somewhat
* nonsensical. Another way to distinguish a 3c90x chip
* from a 3c90xB/C chip is to check for the 'supportsLargePackets'
* bit. This will only be set for 3c90x boomerage chips.
*/
xl_read_eeprom(sc, (caddr_t)&sc->xl_caps, XL_EE_CAPS, 1, 0);
if (sc->xl_caps & XL_CAPS_NO_TXLENGTH ||
!(sc->xl_caps & XL_CAPS_LARGE_PKTS))
sc->xl_type = XL_TYPE_905B;
else
sc->xl_type = XL_TYPE_90X;
ifp = &sc->arpcom.ac_if;
ifp->if_softc = sc;
ifp->if_unit = unit;
ifp->if_name = "xl";
ifp->if_mtu = ETHERMTU;
ifp->if_flags = IFF_BROADCAST | IFF_SIMPLEX | IFF_MULTICAST;
ifp->if_ioctl = xl_ioctl;
ifp->if_output = ether_output;
ifp->if_capabilities = IFCAP_VLAN_MTU;
if (sc->xl_type == XL_TYPE_905B) {
ifp->if_start = xl_start_90xB;
ifp->if_hwassist = XL905B_CSUM_FEATURES;
ifp->if_capabilities |= IFCAP_HWCSUM;
} else
ifp->if_start = xl_start;
ifp->if_watchdog = xl_watchdog;
ifp->if_init = xl_init;
ifp->if_baudrate = 10000000;
ifp->if_snd.ifq_maxlen = XL_TX_LIST_CNT - 1;
ifp->if_capenable = ifp->if_capabilities;
/*
* Now we have to see what sort of media we have.
* This includes probing for an MII interace and a
* possible PHY.
*/
XL_SEL_WIN(3);
sc->xl_media = CSR_READ_2(sc, XL_W3_MEDIA_OPT);
if (bootverbose)
printf("xl%d: media options word: %x\n", sc->xl_unit,
sc->xl_media);
xl_read_eeprom(sc, (char *)&xcvr, XL_EE_ICFG_0, 2, 0);
sc->xl_xcvr = xcvr[0] | xcvr[1] << 16;
sc->xl_xcvr &= XL_ICFG_CONNECTOR_MASK;
sc->xl_xcvr >>= XL_ICFG_CONNECTOR_BITS;
xl_mediacheck(sc);
if (sc->xl_media & XL_MEDIAOPT_MII || sc->xl_media & XL_MEDIAOPT_BTX
|| sc->xl_media & XL_MEDIAOPT_BT4) {
if (bootverbose)
printf("xl%d: found MII/AUTO\n", sc->xl_unit);
xl_setcfg(sc);
if (mii_phy_probe(dev, &sc->xl_miibus,
xl_ifmedia_upd, xl_ifmedia_sts)) {
printf("xl%d: no PHY found!\n", sc->xl_unit);
error = ENXIO;
goto fail;
}
goto done;
}
/*
* Sanity check. If the user has selected "auto" and this isn't
* a 10/100 card of some kind, we need to force the transceiver
* type to something sane.
*/
if (sc->xl_xcvr == XL_XCVR_AUTO)
xl_choose_xcvr(sc, bootverbose);
/*
* Do ifmedia setup.
*/
if (sc->xl_media & XL_MEDIAOPT_BT) {
if (bootverbose)
printf("xl%d: found 10baseT\n", sc->xl_unit);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T, 0, NULL);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_T|IFM_HDX, 0, NULL);
if (sc->xl_caps & XL_CAPS_FULL_DUPLEX)
ifmedia_add(&sc->ifmedia,
IFM_ETHER|IFM_10_T|IFM_FDX, 0, NULL);
}
if (sc->xl_media & (XL_MEDIAOPT_AUI|XL_MEDIAOPT_10FL)) {
/*
* Check for a 10baseFL board in disguise.
*/
if (sc->xl_type == XL_TYPE_905B &&
sc->xl_media == XL_MEDIAOPT_10FL) {
if (bootverbose)
printf("xl%d: found 10baseFL\n", sc->xl_unit);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_FL, 0, NULL);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_FL|IFM_HDX,
0, NULL);
if (sc->xl_caps & XL_CAPS_FULL_DUPLEX)
ifmedia_add(&sc->ifmedia,
IFM_ETHER|IFM_10_FL|IFM_FDX, 0, NULL);
} else {
if (bootverbose)
printf("xl%d: found AUI\n", sc->xl_unit);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_5, 0, NULL);
}
}
if (sc->xl_media & XL_MEDIAOPT_BNC) {
if (bootverbose)
printf("xl%d: found BNC\n", sc->xl_unit);
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_10_2, 0, NULL);
}
if (sc->xl_media & XL_MEDIAOPT_BFX) {
if (bootverbose)
printf("xl%d: found 100baseFX\n", sc->xl_unit);
ifp->if_baudrate = 100000000;
ifmedia_add(&sc->ifmedia, IFM_ETHER|IFM_100_FX, 0, NULL);
}
/* Choose a default media. */
switch(sc->xl_xcvr) {
case XL_XCVR_10BT:
media = IFM_ETHER|IFM_10_T;
xl_setmode(sc, media);
break;
case XL_XCVR_AUI:
if (sc->xl_type == XL_TYPE_905B &&
sc->xl_media == XL_MEDIAOPT_10FL) {
media = IFM_ETHER|IFM_10_FL;
xl_setmode(sc, media);
} else {
media = IFM_ETHER|IFM_10_5;
xl_setmode(sc, media);
}
break;
case XL_XCVR_COAX:
media = IFM_ETHER|IFM_10_2;
xl_setmode(sc, media);
break;
case XL_XCVR_AUTO:
case XL_XCVR_100BTX:
case XL_XCVR_MII:
/* Chosen by miibus */
break;
case XL_XCVR_100BFX:
media = IFM_ETHER|IFM_100_FX;
break;
default:
printf("xl%d: unknown XCVR type: %d\n", sc->xl_unit,
sc->xl_xcvr);
/*
* This will probably be wrong, but it prevents
* the ifmedia code from panicking.
*/
media = IFM_ETHER|IFM_10_T;
break;
}
if (sc->xl_miibus == NULL)
ifmedia_set(&sc->ifmedia, media);
done:
if (sc->xl_flags & XL_FLAG_NO_XCVR_PWR) {
XL_SEL_WIN(0);
CSR_WRITE_2(sc, XL_W0_MFG_ID, XL_NO_XCVR_PWR_MAGICBITS);
}
/*
* Call MI attach routine.
*/
ether_ifattach(ifp, eaddr);
/* Hook interrupt last to avoid having to lock softc */
error = bus_setup_intr(dev, sc->xl_irq, INTR_TYPE_NET,
xl_intr, sc, &sc->xl_intrhand);
if (error) {
printf("xl%d: couldn't set up irq\n", unit);
ether_ifdetach(ifp);
goto fail;
}
fail:
if (error)
xl_detach(dev);
return(error);
}
/*
* Shutdown hardware and free up resources. This can be called any
* time after the mutex has been initialized. It is called in both
* the error case in attach and the normal detach case so it needs
* to be careful about only freeing resources that have actually been
* allocated.
*/
static int
xl_detach(dev)
device_t dev;
{
struct xl_softc *sc;
struct ifnet *ifp;
int rid, res;
sc = device_get_softc(dev);
KASSERT(mtx_initialized(&sc->xl_mtx), ("xl mutex not initialized"));
XL_LOCK(sc);
ifp = &sc->arpcom.ac_if;
if (sc->xl_flags & XL_FLAG_USE_MMIO) {
rid = XL_PCI_LOMEM;
res = SYS_RES_MEMORY;
} else {
rid = XL_PCI_LOIO;
res = SYS_RES_IOPORT;
}
/* These should only be active if attach succeeded */
if (device_is_attached(dev)) {
xl_reset(sc);
xl_stop(sc);
ether_ifdetach(ifp);
}
if (sc->xl_miibus)
device_delete_child(dev, sc->xl_miibus);
bus_generic_detach(dev);
ifmedia_removeall(&sc->ifmedia);
if (sc->xl_intrhand)
bus_teardown_intr(dev, sc->xl_irq, sc->xl_intrhand);
if (sc->xl_irq)
bus_release_resource(dev, SYS_RES_IRQ, 0, sc->xl_irq);
if (sc->xl_fres != NULL)
bus_release_resource(dev, SYS_RES_MEMORY,
XL_PCI_FUNCMEM, sc->xl_fres);
if (sc->xl_res)
bus_release_resource(dev, res, rid, sc->xl_res);
if (sc->xl_mtag) {
bus_dmamap_destroy(sc->xl_mtag, sc->xl_tmpmap);
bus_dma_tag_destroy(sc->xl_mtag);
}
if (sc->xl_ldata.xl_rx_tag) {
bus_dmamap_unload(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap);
bus_dmamem_free(sc->xl_ldata.xl_rx_tag, sc->xl_ldata.xl_rx_list,
sc->xl_ldata.xl_rx_dmamap);
bus_dma_tag_destroy(sc->xl_ldata.xl_rx_tag);
}
if (sc->xl_ldata.xl_tx_tag) {
bus_dmamap_unload(sc->xl_ldata.xl_tx_tag,
sc->xl_ldata.xl_tx_dmamap);
bus_dmamem_free(sc->xl_ldata.xl_tx_tag, sc->xl_ldata.xl_tx_list,
sc->xl_ldata.xl_tx_dmamap);
bus_dma_tag_destroy(sc->xl_ldata.xl_tx_tag);
}
XL_UNLOCK(sc);
mtx_destroy(&sc->xl_mtx);
return(0);
}
/*
* Initialize the transmit descriptors.
*/
static int
xl_list_tx_init(sc)
struct xl_softc *sc;
{
struct xl_chain_data *cd;
struct xl_list_data *ld;
int error, i;
cd = &sc->xl_cdata;
ld = &sc->xl_ldata;
for (i = 0; i < XL_TX_LIST_CNT; i++) {
cd->xl_tx_chain[i].xl_ptr = &ld->xl_tx_list[i];
error = bus_dmamap_create(sc->xl_mtag, 0,
&cd->xl_tx_chain[i].xl_map);
if (error)
return(error);
cd->xl_tx_chain[i].xl_phys = ld->xl_tx_dmaaddr +
i * sizeof(struct xl_list);
if (i == (XL_TX_LIST_CNT - 1))
cd->xl_tx_chain[i].xl_next = NULL;
else
cd->xl_tx_chain[i].xl_next = &cd->xl_tx_chain[i + 1];
}
cd->xl_tx_free = &cd->xl_tx_chain[0];
cd->xl_tx_tail = cd->xl_tx_head = NULL;
bus_dmamap_sync(ld->xl_tx_tag, ld->xl_tx_dmamap, BUS_DMASYNC_PREWRITE);
return(0);
}
/*
* Initialize the transmit descriptors.
*/
static int
xl_list_tx_init_90xB(sc)
struct xl_softc *sc;
{
struct xl_chain_data *cd;
struct xl_list_data *ld;
int error, i;
cd = &sc->xl_cdata;
ld = &sc->xl_ldata;
for (i = 0; i < XL_TX_LIST_CNT; i++) {
cd->xl_tx_chain[i].xl_ptr = &ld->xl_tx_list[i];
error = bus_dmamap_create(sc->xl_mtag, 0,
&cd->xl_tx_chain[i].xl_map);
if (error)
return(error);
cd->xl_tx_chain[i].xl_phys = ld->xl_tx_dmaaddr +
i * sizeof(struct xl_list);
if (i == (XL_TX_LIST_CNT - 1))
cd->xl_tx_chain[i].xl_next = &cd->xl_tx_chain[0];
else
cd->xl_tx_chain[i].xl_next = &cd->xl_tx_chain[i + 1];
if (i == 0)
cd->xl_tx_chain[i].xl_prev =
&cd->xl_tx_chain[XL_TX_LIST_CNT - 1];
else
cd->xl_tx_chain[i].xl_prev =
&cd->xl_tx_chain[i - 1];
}
bzero(ld->xl_tx_list, XL_TX_LIST_SZ);
ld->xl_tx_list[0].xl_status = htole32(XL_TXSTAT_EMPTY);
cd->xl_tx_prod = 1;
cd->xl_tx_cons = 1;
cd->xl_tx_cnt = 0;
bus_dmamap_sync(ld->xl_tx_tag, ld->xl_tx_dmamap, BUS_DMASYNC_PREWRITE);
return(0);
}
/*
* Initialize the RX descriptors and allocate mbufs for them. Note that
* we arrange the descriptors in a closed ring, so that the last descriptor
* points back to the first.
*/
static int
xl_list_rx_init(sc)
struct xl_softc *sc;
{
struct xl_chain_data *cd;
struct xl_list_data *ld;
int error, i, next;
u_int32_t nextptr;
cd = &sc->xl_cdata;
ld = &sc->xl_ldata;
for (i = 0; i < XL_RX_LIST_CNT; i++) {
cd->xl_rx_chain[i].xl_ptr = &ld->xl_rx_list[i];
error = bus_dmamap_create(sc->xl_mtag, 0,
&cd->xl_rx_chain[i].xl_map);
if (error)
return(error);
error = xl_newbuf(sc, &cd->xl_rx_chain[i]);
if (error)
return(error);
if (i == (XL_RX_LIST_CNT - 1))
next = 0;
else
next = i + 1;
nextptr = ld->xl_rx_dmaaddr +
next * sizeof(struct xl_list_onefrag);
cd->xl_rx_chain[i].xl_next = &cd->xl_rx_chain[next];
ld->xl_rx_list[i].xl_next = htole32(nextptr);
}
bus_dmamap_sync(ld->xl_rx_tag, ld->xl_rx_dmamap, BUS_DMASYNC_PREWRITE);
cd->xl_rx_head = &cd->xl_rx_chain[0];
return(0);
}
/*
* Initialize an RX descriptor and attach an MBUF cluster.
* If we fail to do so, we need to leave the old mbuf and
* the old DMA map untouched so that it can be reused.
*/
static int
xl_newbuf(sc, c)
struct xl_softc *sc;
struct xl_chain_onefrag *c;
{
struct mbuf *m_new = NULL;
bus_dmamap_t map;
int error;
u_int32_t baddr;
m_new = m_getcl(M_DONTWAIT, MT_DATA, M_PKTHDR);
if (m_new == NULL)
return(ENOBUFS);
m_new->m_len = m_new->m_pkthdr.len = MCLBYTES;
/* Force longword alignment for packet payload. */
m_adj(m_new, ETHER_ALIGN);
error = bus_dmamap_load_mbuf(sc->xl_mtag, sc->xl_tmpmap, m_new,
xl_dma_map_rxbuf, &baddr, BUS_DMA_NOWAIT);
if (error) {
m_freem(m_new);
printf("xl%d: can't map mbuf (error %d)\n", sc->xl_unit, error);
return(error);
}
bus_dmamap_unload(sc->xl_mtag, c->xl_map);
map = c->xl_map;
c->xl_map = sc->xl_tmpmap;
sc->xl_tmpmap = map;
c->xl_mbuf = m_new;
c->xl_ptr->xl_frag.xl_len = htole32(m_new->m_len | XL_LAST_FRAG);
c->xl_ptr->xl_status = 0;
c->xl_ptr->xl_frag.xl_addr = htole32(baddr);
bus_dmamap_sync(sc->xl_mtag, c->xl_map, BUS_DMASYNC_PREREAD);
return(0);
}
static int
xl_rx_resync(sc)
struct xl_softc *sc;
{
struct xl_chain_onefrag *pos;
int i;
pos = sc->xl_cdata.xl_rx_head;
for (i = 0; i < XL_RX_LIST_CNT; i++) {
if (pos->xl_ptr->xl_status)
break;
pos = pos->xl_next;
}
if (i == XL_RX_LIST_CNT)
return(0);
sc->xl_cdata.xl_rx_head = pos;
return(EAGAIN);
}
/*
* A frame has been uploaded: pass the resulting mbuf chain up to
* the higher level protocols.
*/
static void
xl_rxeof(sc)
struct xl_softc *sc;
{
struct mbuf *m;
struct ifnet *ifp;
struct xl_chain_onefrag *cur_rx;
int total_len = 0;
u_int32_t rxstat;
ifp = &sc->arpcom.ac_if;
again:
bus_dmamap_sync(sc->xl_ldata.xl_rx_tag, sc->xl_ldata.xl_rx_dmamap,
BUS_DMASYNC_POSTREAD);
while((rxstat = le32toh(sc->xl_cdata.xl_rx_head->xl_ptr->xl_status))) {
cur_rx = sc->xl_cdata.xl_rx_head;
sc->xl_cdata.xl_rx_head = cur_rx->xl_next;
total_len = rxstat & XL_RXSTAT_LENMASK;
/*
* Since we have told the chip to allow large frames,
* we need to trap giant frame errors in software. We allow
* a little more than the normal frame size to account for
* frames with VLAN tags.
*/
if (total_len > XL_MAX_FRAMELEN)
rxstat |= (XL_RXSTAT_UP_ERROR|XL_RXSTAT_OVERSIZE);
/*
* If an error occurs, update stats, clear the
* status word and leave the mbuf cluster in place:
* it should simply get re-used next time this descriptor
* comes up in the ring.
*/
if (rxstat & XL_RXSTAT_UP_ERROR) {
ifp->if_ierrors++;
cur_rx->xl_ptr->xl_status = 0;
bus_dmamap_sync(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap, BUS_DMASYNC_PREWRITE);
continue;
}
/*
* If the error bit was not set, the upload complete
* bit should be set which means we have a valid packet.
* If not, something truly strange has happened.
*/
if (!(rxstat & XL_RXSTAT_UP_CMPLT)) {
printf("xl%d: bad receive status -- "
"packet dropped\n", sc->xl_unit);
ifp->if_ierrors++;
cur_rx->xl_ptr->xl_status = 0;
bus_dmamap_sync(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap, BUS_DMASYNC_PREWRITE);
continue;
}
/* No errors; receive the packet. */
bus_dmamap_sync(sc->xl_mtag, cur_rx->xl_map,
BUS_DMASYNC_POSTREAD);
m = cur_rx->xl_mbuf;
/*
* Try to conjure up a new mbuf cluster. If that
* fails, it means we have an out of memory condition and
* should leave the buffer in place and continue. This will
* result in a lost packet, but there's little else we
* can do in this situation.
*/
if (xl_newbuf(sc, cur_rx)) {
ifp->if_ierrors++;
cur_rx->xl_ptr->xl_status = 0;
bus_dmamap_sync(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap, BUS_DMASYNC_PREWRITE);
continue;
}
bus_dmamap_sync(sc->xl_ldata.xl_rx_tag,
sc->xl_ldata.xl_rx_dmamap, BUS_DMASYNC_PREWRITE);
ifp->if_ipackets++;
m->m_pkthdr.rcvif = ifp;
m->m_pkthdr.len = m->m_len = total_len;
if (ifp->if_capenable & IFCAP_RXCSUM) {
/* Do IP checksum checking. */
if (rxstat & XL_RXSTAT_IPCKOK)
m->m_pkthdr.csum_flags |= CSUM_IP_CHECKED;
if (!(rxstat & XL_RXSTAT_IPCKERR))
m->m_pkthdr.csum_flags |= CSUM_IP_VALID;
if ((rxstat & XL_RXSTAT_TCPCOK &&
!(rxstat & XL_RXSTAT_TCPCKERR)) ||
(rxstat & XL_RXSTAT_UDPCKOK &&
!(rxstat & XL_RXSTAT_UDPCKERR))) {
m->m_pkthdr.csum_flags |=
CSUM_DATA_VALID|CSUM_PSEUDO_HDR;
m->m_pkthdr.csum_data = 0xffff;
}
}
(*ifp->if_input)(ifp, m);
}
/*
* Handle the 'end of channel' condition. When the upload
* engine hits the end of the RX ring, it will stall. This
* is our cue to flush the RX ring, reload the uplist pointer
* register and unstall the engine.
* XXX This is actually a little goofy. With the ThunderLAN
* chip, you get an interrupt when the receiver hits the end
* of the receive ring, which tells you exactly when you
* you need to reload the ring pointer. Here we have to
* fake it. I'm mad at myself for not being clever enough
* to avoid the use of a goto here.
*/
if (CSR_READ_4(sc, XL_UPLIST_PTR) == 0 ||
CSR_READ_4(sc, XL_UPLIST_STATUS) & XL_PKTSTAT_UP_STALLED) {
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_UP_STALL);
xl_wait(sc);
CSR_WRITE_4(sc, XL_UPLIST_PTR, sc->xl_ldata.xl_rx_dmaaddr);
sc->xl_cdata.xl_rx_head = &sc->xl_cdata.xl_rx_chain[0];
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_UP_UNSTALL);
goto again;
}
return;
}
/*
* A frame was downloaded to the chip. It's safe for us to clean up
* the list buffers.
*/
static void
xl_txeof(sc)
struct xl_softc *sc;
{
struct xl_chain *cur_tx;
struct ifnet *ifp;
ifp = &sc->arpcom.ac_if;
/* Clear the timeout timer. */
ifp->if_timer = 0;
/*
* Go through our tx list and free mbufs for those
* frames that have been uploaded. Note: the 3c905B
* sets a special bit in the status word to let us
* know that a frame has been downloaded, but the
* original 3c900/3c905 adapters don't do that.
* Consequently, we have to use a different test if
* xl_type != XL_TYPE_905B.
*/
while(sc->xl_cdata.xl_tx_head != NULL) {
cur_tx = sc->xl_cdata.xl_tx_head;
if (CSR_READ_4(sc, XL_DOWNLIST_PTR))
break;
sc->xl_cdata.xl_tx_head = cur_tx->xl_next;
bus_dmamap_sync(sc->xl_mtag, cur_tx->xl_map,
BUS_DMASYNC_POSTWRITE);
bus_dmamap_unload(sc->xl_mtag, cur_tx->xl_map);
m_freem(cur_tx->xl_mbuf);
cur_tx->xl_mbuf = NULL;
ifp->if_opackets++;
cur_tx->xl_next = sc->xl_cdata.xl_tx_free;
sc->xl_cdata.xl_tx_free = cur_tx;
}
if (sc->xl_cdata.xl_tx_head == NULL) {
ifp->if_flags &= ~IFF_OACTIVE;
sc->xl_cdata.xl_tx_tail = NULL;
} else {
if (CSR_READ_4(sc, XL_DMACTL) & XL_DMACTL_DOWN_STALLED ||
!CSR_READ_4(sc, XL_DOWNLIST_PTR)) {
CSR_WRITE_4(sc, XL_DOWNLIST_PTR,
sc->xl_cdata.xl_tx_head->xl_phys);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_UNSTALL);
}
}
return;
}
static void
xl_txeof_90xB(sc)
struct xl_softc *sc;
{
struct xl_chain *cur_tx = NULL;
struct ifnet *ifp;
int idx;
ifp = &sc->arpcom.ac_if;
bus_dmamap_sync(sc->xl_ldata.xl_tx_tag, sc->xl_ldata.xl_tx_dmamap,
BUS_DMASYNC_POSTREAD);
idx = sc->xl_cdata.xl_tx_cons;
while(idx != sc->xl_cdata.xl_tx_prod) {
cur_tx = &sc->xl_cdata.xl_tx_chain[idx];
if (!(le32toh(cur_tx->xl_ptr->xl_status) &
XL_TXSTAT_DL_COMPLETE))
break;
if (cur_tx->xl_mbuf != NULL) {
bus_dmamap_sync(sc->xl_mtag, cur_tx->xl_map,
BUS_DMASYNC_POSTWRITE);
bus_dmamap_unload(sc->xl_mtag, cur_tx->xl_map);
m_freem(cur_tx->xl_mbuf);
cur_tx->xl_mbuf = NULL;
}
ifp->if_opackets++;
sc->xl_cdata.xl_tx_cnt--;
XL_INC(idx, XL_TX_LIST_CNT);
ifp->if_timer = 0;
}
sc->xl_cdata.xl_tx_cons = idx;
if (cur_tx != NULL)
ifp->if_flags &= ~IFF_OACTIVE;
return;
}
/*
* TX 'end of channel' interrupt handler. Actually, we should
* only get a 'TX complete' interrupt if there's a transmit error,
* so this is really TX error handler.
*/
static void
xl_txeoc(sc)
struct xl_softc *sc;
{
u_int8_t txstat;
while((txstat = CSR_READ_1(sc, XL_TX_STATUS))) {
if (txstat & XL_TXSTATUS_UNDERRUN ||
txstat & XL_TXSTATUS_JABBER ||
txstat & XL_TXSTATUS_RECLAIM) {
printf("xl%d: transmission error: %x\n",
sc->xl_unit, txstat);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_RESET);
xl_wait(sc);
if (sc->xl_type == XL_TYPE_905B) {
if (sc->xl_cdata.xl_tx_cnt) {
int i;
struct xl_chain *c;
i = sc->xl_cdata.xl_tx_cons;
c = &sc->xl_cdata.xl_tx_chain[i];
CSR_WRITE_4(sc, XL_DOWNLIST_PTR,
c->xl_phys);
CSR_WRITE_1(sc, XL_DOWN_POLL, 64);
}
} else {
if (sc->xl_cdata.xl_tx_head != NULL)
CSR_WRITE_4(sc, XL_DOWNLIST_PTR,
sc->xl_cdata.xl_tx_head->xl_phys);
}
/*
* Remember to set this for the
* first generation 3c90X chips.
*/
CSR_WRITE_1(sc, XL_TX_FREETHRESH, XL_PACKET_SIZE >> 8);
if (txstat & XL_TXSTATUS_UNDERRUN &&
sc->xl_tx_thresh < XL_PACKET_SIZE) {
sc->xl_tx_thresh += XL_MIN_FRAMELEN;
printf("xl%d: tx underrun, increasing tx start"
" threshold to %d bytes\n", sc->xl_unit,
sc->xl_tx_thresh);
}
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_TX_SET_START|sc->xl_tx_thresh);
if (sc->xl_type == XL_TYPE_905B) {
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_SET_TX_RECLAIM|(XL_PACKET_SIZE >> 4));
}
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_ENABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_UNSTALL);
} else {
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_ENABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_UNSTALL);
}
/*
* Write an arbitrary byte to the TX_STATUS register
* to clear this interrupt/error and advance to the next.
*/
CSR_WRITE_1(sc, XL_TX_STATUS, 0x01);
}
return;
}
static void
xl_intr(arg)
void *arg;
{
struct xl_softc *sc;
struct ifnet *ifp;
u_int16_t status;
sc = arg;
XL_LOCK(sc);
ifp = &sc->arpcom.ac_if;
while((status = CSR_READ_2(sc, XL_STATUS)) & XL_INTRS && status != 0xFFFF) {
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_INTR_ACK|(status & XL_INTRS));
if (status & XL_STAT_UP_COMPLETE) {
int curpkts;
curpkts = ifp->if_ipackets;
xl_rxeof(sc);
if (curpkts == ifp->if_ipackets) {
while (xl_rx_resync(sc))
xl_rxeof(sc);
}
}
if (status & XL_STAT_DOWN_COMPLETE) {
if (sc->xl_type == XL_TYPE_905B)
xl_txeof_90xB(sc);
else
xl_txeof(sc);
}
if (status & XL_STAT_TX_COMPLETE) {
ifp->if_oerrors++;
xl_txeoc(sc);
}
if (status & XL_STAT_ADFAIL) {
xl_reset(sc);
xl_init(sc);
}
if (status & XL_STAT_STATSOFLOW) {
sc->xl_stats_no_timeout = 1;
xl_stats_update(sc);
sc->xl_stats_no_timeout = 0;
}
}
if (ifp->if_snd.ifq_head != NULL)
(*ifp->if_start)(ifp);
XL_UNLOCK(sc);
return;
}
static void
xl_stats_update(xsc)
void *xsc;
{
struct xl_softc *sc;
struct ifnet *ifp;
struct xl_stats xl_stats;
u_int8_t *p;
int i;
struct mii_data *mii = NULL;
bzero((char *)&xl_stats, sizeof(struct xl_stats));
sc = xsc;
ifp = &sc->arpcom.ac_if;
if (sc->xl_miibus != NULL)
mii = device_get_softc(sc->xl_miibus);
p = (u_int8_t *)&xl_stats;
/* Read all the stats registers. */
XL_SEL_WIN(6);
for (i = 0; i < 16; i++)
*p++ = CSR_READ_1(sc, XL_W6_CARRIER_LOST + i);
ifp->if_ierrors += xl_stats.xl_rx_overrun;
ifp->if_collisions += xl_stats.xl_tx_multi_collision +
xl_stats.xl_tx_single_collision +
xl_stats.xl_tx_late_collision;
/*
* Boomerang and cyclone chips have an extra stats counter
* in window 4 (BadSSD). We have to read this too in order
* to clear out all the stats registers and avoid a statsoflow
* interrupt.
*/
XL_SEL_WIN(4);
CSR_READ_1(sc, XL_W4_BADSSD);
if ((mii != NULL) && (!sc->xl_stats_no_timeout))
mii_tick(mii);
XL_SEL_WIN(7);
if (!sc->xl_stats_no_timeout)
sc->xl_stat_ch = timeout(xl_stats_update, sc, hz);
return;
}
/*
* Encapsulate an mbuf chain in a descriptor by coupling the mbuf data
* pointers to the fragment pointers.
*/
static int
xl_encap(sc, c, m_head)
struct xl_softc *sc;
struct xl_chain *c;
struct mbuf *m_head;
{
int error;
u_int32_t status;
struct ifnet *ifp;
ifp = &sc->arpcom.ac_if;
/*
* Start packing the mbufs in this chain into
* the fragment pointers. Stop when we run out
* of fragments or hit the end of the mbuf chain.
*/
error = bus_dmamap_load_mbuf(sc->xl_mtag, c->xl_map, m_head,
xl_dma_map_txbuf, c->xl_ptr, BUS_DMA_NOWAIT);
if (error && error != EFBIG) {
m_freem(m_head);
printf("xl%d: can't map mbuf (error %d)\n", sc->xl_unit, error);
return(1);
}
/*
* Handle special case: we used up all 63 fragments,
* but we have more mbufs left in the chain. Copy the
* data into an mbuf cluster. Note that we don't
* bother clearing the values in the other fragment
* pointers/counters; it wouldn't gain us anything,
* and would waste cycles.
*/
if (error) {
struct mbuf *m_new;
m_new = m_defrag(m_head, M_DONTWAIT);
if (m_new == NULL) {
m_freem(m_head);
return(1);
} else {
m_head = m_new;
}
error = bus_dmamap_load_mbuf(sc->xl_mtag, c->xl_map,
m_head, xl_dma_map_txbuf, c->xl_ptr, BUS_DMA_NOWAIT);
if (error) {
m_freem(m_head);
printf("xl%d: can't map mbuf (error %d)\n",
sc->xl_unit, error);
return(1);
}
}
if (sc->xl_type == XL_TYPE_905B) {
status = XL_TXSTAT_RND_DEFEAT;
if (m_head->m_pkthdr.csum_flags) {
if (m_head->m_pkthdr.csum_flags & CSUM_IP)
status |= XL_TXSTAT_IPCKSUM;
if (m_head->m_pkthdr.csum_flags & CSUM_TCP)
status |= XL_TXSTAT_TCPCKSUM;
if (m_head->m_pkthdr.csum_flags & CSUM_UDP)
status |= XL_TXSTAT_UDPCKSUM;
}
c->xl_ptr->xl_status = htole32(status);
}
c->xl_mbuf = m_head;
bus_dmamap_sync(sc->xl_mtag, c->xl_map, BUS_DMASYNC_PREWRITE);
return(0);
}
/*
* Main transmit routine. To avoid having to do mbuf copies, we put pointers
* to the mbuf data regions directly in the transmit lists. We also save a
* copy of the pointers since the transmit list fragment pointers are
* physical addresses.
*/
static void
xl_start(ifp)
struct ifnet *ifp;
{
struct xl_softc *sc;
struct mbuf *m_head = NULL;
struct xl_chain *prev = NULL, *cur_tx = NULL, *start_tx;
struct xl_chain *prev_tx;
u_int32_t status;
int error;
sc = ifp->if_softc;
XL_LOCK(sc);
/*
* Check for an available queue slot. If there are none,
* punt.
*/
if (sc->xl_cdata.xl_tx_free == NULL) {
xl_txeoc(sc);
xl_txeof(sc);
if (sc->xl_cdata.xl_tx_free == NULL) {
ifp->if_flags |= IFF_OACTIVE;
XL_UNLOCK(sc);
return;
}
}
start_tx = sc->xl_cdata.xl_tx_free;
while(sc->xl_cdata.xl_tx_free != NULL) {
IF_DEQUEUE(&ifp->if_snd, m_head);
if (m_head == NULL)
break;
/* Pick a descriptor off the free list. */
prev_tx = cur_tx;
cur_tx = sc->xl_cdata.xl_tx_free;
/* Pack the data into the descriptor. */
error = xl_encap(sc, cur_tx, m_head);
if (error) {
cur_tx = prev_tx;
continue;
}
sc->xl_cdata.xl_tx_free = cur_tx->xl_next;
cur_tx->xl_next = NULL;
/* Chain it together. */
if (prev != NULL) {
prev->xl_next = cur_tx;
prev->xl_ptr->xl_next = htole32(cur_tx->xl_phys);
}
prev = cur_tx;
/*
* If there's a BPF listener, bounce a copy of this frame
* to him.
*/
BPF_MTAP(ifp, cur_tx->xl_mbuf);
}
/*
* If there are no packets queued, bail.
*/
if (cur_tx == NULL) {
XL_UNLOCK(sc);
return;
}
/*
* Place the request for the upload interrupt
* in the last descriptor in the chain. This way, if
* we're chaining several packets at once, we'll only
* get an interupt once for the whole chain rather than
* once for each packet.
*/
cur_tx->xl_ptr->xl_status = htole32(le32toh(cur_tx->xl_ptr->xl_status) |
XL_TXSTAT_DL_INTR);
bus_dmamap_sync(sc->xl_ldata.xl_tx_tag, sc->xl_ldata.xl_tx_dmamap,
BUS_DMASYNC_PREWRITE);
/*
* Queue the packets. If the TX channel is clear, update
* the downlist pointer register.
*/
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_STALL);
xl_wait(sc);
if (sc->xl_cdata.xl_tx_head != NULL) {
sc->xl_cdata.xl_tx_tail->xl_next = start_tx;
sc->xl_cdata.xl_tx_tail->xl_ptr->xl_next =
htole32(start_tx->xl_phys);
status = sc->xl_cdata.xl_tx_tail->xl_ptr->xl_status;
sc->xl_cdata.xl_tx_tail->xl_ptr->xl_status =
htole32(le32toh(status) & ~XL_TXSTAT_DL_INTR);
sc->xl_cdata.xl_tx_tail = cur_tx;
} else {
sc->xl_cdata.xl_tx_head = start_tx;
sc->xl_cdata.xl_tx_tail = cur_tx;
}
if (!CSR_READ_4(sc, XL_DOWNLIST_PTR))
CSR_WRITE_4(sc, XL_DOWNLIST_PTR, start_tx->xl_phys);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_UNSTALL);
XL_SEL_WIN(7);
/*
* Set a timeout in case the chip goes out to lunch.
*/
ifp->if_timer = 5;
/*
* XXX Under certain conditions, usually on slower machines
* where interrupts may be dropped, it's possible for the
* adapter to chew up all the buffers in the receive ring
* and stall, without us being able to do anything about it.
* To guard against this, we need to make a pass over the
* RX queue to make sure there aren't any packets pending.
* Doing it here means we can flush the receive ring at the
* same time the chip is DMAing the transmit descriptors we
* just gave it.
*
* 3Com goes to some lengths to emphasize the Parallel Tasking (tm)
* nature of their chips in all their marketing literature;
* we may as well take advantage of it. :)
*/
xl_rxeof(sc);
XL_UNLOCK(sc);
return;
}
static void
xl_start_90xB(ifp)
struct ifnet *ifp;
{
struct xl_softc *sc;
struct mbuf *m_head = NULL;
struct xl_chain *prev = NULL, *cur_tx = NULL, *start_tx;
struct xl_chain *prev_tx;
int error, idx;
sc = ifp->if_softc;
XL_LOCK(sc);
if (ifp->if_flags & IFF_OACTIVE) {
XL_UNLOCK(sc);
return;
}
idx = sc->xl_cdata.xl_tx_prod;
start_tx = &sc->xl_cdata.xl_tx_chain[idx];
while (sc->xl_cdata.xl_tx_chain[idx].xl_mbuf == NULL) {
if ((XL_TX_LIST_CNT - sc->xl_cdata.xl_tx_cnt) < 3) {
ifp->if_flags |= IFF_OACTIVE;
break;
}
IF_DEQUEUE(&ifp->if_snd, m_head);
if (m_head == NULL)
break;
prev_tx = cur_tx;
cur_tx = &sc->xl_cdata.xl_tx_chain[idx];
/* Pack the data into the descriptor. */
error = xl_encap(sc, cur_tx, m_head);
if (error) {
cur_tx = prev_tx;
continue;
}
/* Chain it together. */
if (prev != NULL)
prev->xl_ptr->xl_next = htole32(cur_tx->xl_phys);
prev = cur_tx;
/*
* If there's a BPF listener, bounce a copy of this frame
* to him.
*/
BPF_MTAP(ifp, cur_tx->xl_mbuf);
XL_INC(idx, XL_TX_LIST_CNT);
sc->xl_cdata.xl_tx_cnt++;
}
/*
* If there are no packets queued, bail.
*/
if (cur_tx == NULL) {
XL_UNLOCK(sc);
return;
}
/*
* Place the request for the upload interrupt
* in the last descriptor in the chain. This way, if
* we're chaining several packets at once, we'll only
* get an interupt once for the whole chain rather than
* once for each packet.
*/
cur_tx->xl_ptr->xl_status = htole32(le32toh(cur_tx->xl_ptr->xl_status) |
XL_TXSTAT_DL_INTR);
bus_dmamap_sync(sc->xl_ldata.xl_tx_tag, sc->xl_ldata.xl_tx_dmamap,
BUS_DMASYNC_PREWRITE);
/* Start transmission */
sc->xl_cdata.xl_tx_prod = idx;
start_tx->xl_prev->xl_ptr->xl_next = htole32(start_tx->xl_phys);
/*
* Set a timeout in case the chip goes out to lunch.
*/
ifp->if_timer = 5;
XL_UNLOCK(sc);
return;
}
static void
xl_init(xsc)
void *xsc;
{
struct xl_softc *sc = xsc;
struct ifnet *ifp = &sc->arpcom.ac_if;
int error, i;
u_int16_t rxfilt = 0;
struct mii_data *mii = NULL;
XL_LOCK(sc);
/*
* Cancel pending I/O and free all RX/TX buffers.
*/
xl_stop(sc);
if (sc->xl_miibus == NULL) {
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_RESET);
xl_wait(sc);
}
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_RESET);
xl_wait(sc);
DELAY(10000);
if (sc->xl_miibus != NULL)
mii = device_get_softc(sc->xl_miibus);
/* Init our MAC address */
XL_SEL_WIN(2);
for (i = 0; i < ETHER_ADDR_LEN; i++) {
CSR_WRITE_1(sc, XL_W2_STATION_ADDR_LO + i,
sc->arpcom.ac_enaddr[i]);
}
/* Clear the station mask. */
for (i = 0; i < 3; i++)
CSR_WRITE_2(sc, XL_W2_STATION_MASK_LO + (i * 2), 0);
#ifdef notdef
/* Reset TX and RX. */
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_RESET);
xl_wait(sc);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_RESET);
xl_wait(sc);
#endif
/* Init circular RX list. */
error = xl_list_rx_init(sc);
if (error) {
printf("xl%d: initialization of the rx ring failed (%d)\n",
sc->xl_unit, error);
xl_stop(sc);
XL_UNLOCK(sc);
return;
}
/* Init TX descriptors. */
if (sc->xl_type == XL_TYPE_905B)
error = xl_list_tx_init_90xB(sc);
else
error = xl_list_tx_init(sc);
if (error) {
printf("xl%d: initialization of the tx ring failed (%d)\n",
sc->xl_unit, error);
xl_stop(sc);
XL_UNLOCK(sc);
}
/*
* Set the TX freethresh value.
* Note that this has no effect on 3c905B "cyclone"
* cards but is required for 3c900/3c905 "boomerang"
* cards in order to enable the download engine.
*/
CSR_WRITE_1(sc, XL_TX_FREETHRESH, XL_PACKET_SIZE >> 8);
/* Set the TX start threshold for best performance. */
sc->xl_tx_thresh = XL_MIN_FRAMELEN;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_SET_START|sc->xl_tx_thresh);
/*
* If this is a 3c905B, also set the tx reclaim threshold.
* This helps cut down on the number of tx reclaim errors
* that could happen on a busy network. The chip multiplies
* the register value by 16 to obtain the actual threshold
* in bytes, so we divide by 16 when setting the value here.
* The existing threshold value can be examined by reading
* the register at offset 9 in window 5.
*/
if (sc->xl_type == XL_TYPE_905B) {
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_SET_TX_RECLAIM|(XL_PACKET_SIZE >> 4));
}
/* Set RX filter bits. */
XL_SEL_WIN(5);
rxfilt = CSR_READ_1(sc, XL_W5_RX_FILTER);
/* Set the individual bit to receive frames for this host only. */
rxfilt |= XL_RXFILTER_INDIVIDUAL;
/* If we want promiscuous mode, set the allframes bit. */
if (ifp->if_flags & IFF_PROMISC) {
rxfilt |= XL_RXFILTER_ALLFRAMES;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
} else {
rxfilt &= ~XL_RXFILTER_ALLFRAMES;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
}
/*
* Set capture broadcast bit to capture broadcast frames.
*/
if (ifp->if_flags & IFF_BROADCAST) {
rxfilt |= XL_RXFILTER_BROADCAST;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
} else {
rxfilt &= ~XL_RXFILTER_BROADCAST;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_FILT|rxfilt);
}
/*
* Program the multicast filter, if necessary.
*/
if (sc->xl_type == XL_TYPE_905B)
xl_setmulti_hash(sc);
else
xl_setmulti(sc);
/*
* Load the address of the RX list. We have to
* stall the upload engine before we can manipulate
* the uplist pointer register, then unstall it when
* we're finished. We also have to wait for the
* stall command to complete before proceeding.
* Note that we have to do this after any RX resets
* have completed since the uplist register is cleared
* by a reset.
*/
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_UP_STALL);
xl_wait(sc);
CSR_WRITE_4(sc, XL_UPLIST_PTR, sc->xl_ldata.xl_rx_dmaaddr);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_UP_UNSTALL);
xl_wait(sc);
if (sc->xl_type == XL_TYPE_905B) {
/* Set polling interval */
CSR_WRITE_1(sc, XL_DOWN_POLL, 64);
/* Load the address of the TX list */
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_STALL);
xl_wait(sc);
CSR_WRITE_4(sc, XL_DOWNLIST_PTR,
sc->xl_cdata.xl_tx_chain[0].xl_phys);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_DOWN_UNSTALL);
xl_wait(sc);
}
/*
* If the coax transceiver is on, make sure to enable
* the DC-DC converter.
*/
XL_SEL_WIN(3);
if (sc->xl_xcvr == XL_XCVR_COAX)
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_START);
else
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_STOP);
/*
* increase packet size to allow reception of 802.1q or ISL packets.
* For the 3c90x chip, set the 'allow large packets' bit in the MAC
* control register. For 3c90xB/C chips, use the RX packet size
* register.
*/
if (sc->xl_type == XL_TYPE_905B)
CSR_WRITE_2(sc, XL_W3_MAXPKTSIZE, XL_PACKET_SIZE);
else {
u_int8_t macctl;
macctl = CSR_READ_1(sc, XL_W3_MAC_CTRL);
macctl |= XL_MACCTRL_ALLOW_LARGE_PACK;
CSR_WRITE_1(sc, XL_W3_MAC_CTRL, macctl);
}
/* Clear out the stats counters. */
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_STATS_DISABLE);
sc->xl_stats_no_timeout = 1;
xl_stats_update(sc);
sc->xl_stats_no_timeout = 0;
XL_SEL_WIN(4);
CSR_WRITE_2(sc, XL_W4_NET_DIAG, XL_NETDIAG_UPPER_BYTES_ENABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_STATS_ENABLE);
/*
* Enable interrupts.
*/
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_INTR_ACK|0xFF);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_STAT_ENB|XL_INTRS);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_INTR_ENB|XL_INTRS);
if (sc->xl_flags & XL_FLAG_FUNCREG)
bus_space_write_4(sc->xl_ftag, sc->xl_fhandle, 4, 0x8000);
/* Set the RX early threshold */
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_SET_THRESH|(XL_PACKET_SIZE >>2));
CSR_WRITE_2(sc, XL_DMACTL, XL_DMACTL_UP_RX_EARLY);
/* Enable receiver and transmitter. */
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_ENABLE);
xl_wait(sc);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_ENABLE);
xl_wait(sc);
if (mii != NULL)
mii_mediachg(mii);
/* Select window 7 for normal operations. */
XL_SEL_WIN(7);
ifp->if_flags |= IFF_RUNNING;
ifp->if_flags &= ~IFF_OACTIVE;
sc->xl_stat_ch = timeout(xl_stats_update, sc, hz);
XL_UNLOCK(sc);
return;
}
/*
* Set media options.
*/
static int
xl_ifmedia_upd(ifp)
struct ifnet *ifp;
{
struct xl_softc *sc;
struct ifmedia *ifm = NULL;
struct mii_data *mii = NULL;
sc = ifp->if_softc;
if (sc->xl_miibus != NULL)
mii = device_get_softc(sc->xl_miibus);
if (mii == NULL)
ifm = &sc->ifmedia;
else
ifm = &mii->mii_media;
switch(IFM_SUBTYPE(ifm->ifm_media)) {
case IFM_100_FX:
case IFM_10_FL:
case IFM_10_2:
case IFM_10_5:
xl_setmode(sc, ifm->ifm_media);
return(0);
break;
default:
break;
}
if (sc->xl_media & XL_MEDIAOPT_MII || sc->xl_media & XL_MEDIAOPT_BTX
|| sc->xl_media & XL_MEDIAOPT_BT4) {
xl_init(sc);
} else {
xl_setmode(sc, ifm->ifm_media);
}
return(0);
}
/*
* Report current media status.
*/
static void
xl_ifmedia_sts(ifp, ifmr)
struct ifnet *ifp;
struct ifmediareq *ifmr;
{
struct xl_softc *sc;
u_int32_t icfg;
struct mii_data *mii = NULL;
sc = ifp->if_softc;
if (sc->xl_miibus != NULL)
mii = device_get_softc(sc->xl_miibus);
XL_SEL_WIN(3);
icfg = CSR_READ_4(sc, XL_W3_INTERNAL_CFG) & XL_ICFG_CONNECTOR_MASK;
icfg >>= XL_ICFG_CONNECTOR_BITS;
ifmr->ifm_active = IFM_ETHER;
switch(icfg) {
case XL_XCVR_10BT:
ifmr->ifm_active = IFM_ETHER|IFM_10_T;
if (CSR_READ_1(sc, XL_W3_MAC_CTRL) & XL_MACCTRL_DUPLEX)
ifmr->ifm_active |= IFM_FDX;
else
ifmr->ifm_active |= IFM_HDX;
break;
case XL_XCVR_AUI:
if (sc->xl_type == XL_TYPE_905B &&
sc->xl_media == XL_MEDIAOPT_10FL) {
ifmr->ifm_active = IFM_ETHER|IFM_10_FL;
if (CSR_READ_1(sc, XL_W3_MAC_CTRL) & XL_MACCTRL_DUPLEX)
ifmr->ifm_active |= IFM_FDX;
else
ifmr->ifm_active |= IFM_HDX;
} else
ifmr->ifm_active = IFM_ETHER|IFM_10_5;
break;
case XL_XCVR_COAX:
ifmr->ifm_active = IFM_ETHER|IFM_10_2;
break;
/*
* XXX MII and BTX/AUTO should be separate cases.
*/
case XL_XCVR_100BTX:
case XL_XCVR_AUTO:
case XL_XCVR_MII:
if (mii != NULL) {
mii_pollstat(mii);
ifmr->ifm_active = mii->mii_media_active;
ifmr->ifm_status = mii->mii_media_status;
}
break;
case XL_XCVR_100BFX:
ifmr->ifm_active = IFM_ETHER|IFM_100_FX;
break;
default:
printf("xl%d: unknown XCVR type: %d\n", sc->xl_unit, icfg);
break;
}
return;
}
static int
xl_ioctl(ifp, command, data)
struct ifnet *ifp;
u_long command;
caddr_t data;
{
struct xl_softc *sc = ifp->if_softc;
struct ifreq *ifr = (struct ifreq *) data;
int error = 0;
struct mii_data *mii = NULL;
u_int8_t rxfilt;
XL_LOCK(sc);
switch(command) {
case SIOCSIFFLAGS:
XL_SEL_WIN(5);
rxfilt = CSR_READ_1(sc, XL_W5_RX_FILTER);
if (ifp->if_flags & IFF_UP) {
if (ifp->if_flags & IFF_RUNNING &&
ifp->if_flags & IFF_PROMISC &&
!(sc->xl_if_flags & IFF_PROMISC)) {
rxfilt |= XL_RXFILTER_ALLFRAMES;
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_RX_SET_FILT|rxfilt);
XL_SEL_WIN(7);
} else if (ifp->if_flags & IFF_RUNNING &&
!(ifp->if_flags & IFF_PROMISC) &&
sc->xl_if_flags & IFF_PROMISC) {
rxfilt &= ~XL_RXFILTER_ALLFRAMES;
CSR_WRITE_2(sc, XL_COMMAND,
XL_CMD_RX_SET_FILT|rxfilt);
XL_SEL_WIN(7);
} else
xl_init(sc);
} else {
if (ifp->if_flags & IFF_RUNNING)
xl_stop(sc);
}
sc->xl_if_flags = ifp->if_flags;
error = 0;
break;
case SIOCADDMULTI:
case SIOCDELMULTI:
if (sc->xl_type == XL_TYPE_905B)
xl_setmulti_hash(sc);
else
xl_setmulti(sc);
error = 0;
break;
case SIOCGIFMEDIA:
case SIOCSIFMEDIA:
if (sc->xl_miibus != NULL)
mii = device_get_softc(sc->xl_miibus);
if (mii == NULL)
error = ifmedia_ioctl(ifp, ifr,
&sc->ifmedia, command);
else
error = ifmedia_ioctl(ifp, ifr,
&mii->mii_media, command);
break;
case SIOCSIFCAP:
ifp->if_capenable = ifr->ifr_reqcap;
if (ifp->if_capenable & IFCAP_TXCSUM)
ifp->if_hwassist = XL905B_CSUM_FEATURES;
else
ifp->if_hwassist = 0;
break;
default:
error = ether_ioctl(ifp, command, data);
break;
}
XL_UNLOCK(sc);
return(error);
}
static void
xl_watchdog(ifp)
struct ifnet *ifp;
{
struct xl_softc *sc;
u_int16_t status = 0;
sc = ifp->if_softc;
XL_LOCK(sc);
ifp->if_oerrors++;
XL_SEL_WIN(4);
status = CSR_READ_2(sc, XL_W4_MEDIA_STATUS);
printf("xl%d: watchdog timeout\n", sc->xl_unit);
if (status & XL_MEDIASTAT_CARRIER)
printf("xl%d: no carrier - transceiver cable problem?\n",
sc->xl_unit);
xl_txeoc(sc);
xl_txeof(sc);
xl_rxeof(sc);
xl_reset(sc);
xl_init(sc);
if (ifp->if_snd.ifq_head != NULL)
(*ifp->if_start)(ifp);
XL_UNLOCK(sc);
return;
}
/*
* Stop the adapter and free any mbufs allocated to the
* RX and TX lists.
*/
static void
xl_stop(sc)
struct xl_softc *sc;
{
register int i;
struct ifnet *ifp;
XL_LOCK(sc);
ifp = &sc->arpcom.ac_if;
ifp->if_timer = 0;
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_DISABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_STATS_DISABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_INTR_ENB);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_DISCARD);
xl_wait(sc);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_DISABLE);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_COAX_STOP);
DELAY(800);
#ifdef foo
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_RX_RESET);
xl_wait(sc);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_TX_RESET);
xl_wait(sc);
#endif
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_INTR_ACK|XL_STAT_INTLATCH);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_STAT_ENB|0);
CSR_WRITE_2(sc, XL_COMMAND, XL_CMD_INTR_ENB|0);
if (sc->xl_flags & XL_FLAG_FUNCREG) bus_space_write_4 (sc->xl_ftag, sc->xl_fhandle, 4, 0x8000);
/* Stop the stats updater. */
untimeout(xl_stats_update, sc, sc->xl_stat_ch);
/*
* Free data in the RX lists.
*/
for (i = 0; i < XL_RX_LIST_CNT; i++) {
if (sc->xl_cdata.xl_rx_chain[i].xl_mbuf != NULL) {
bus_dmamap_unload(sc->xl_mtag,
sc->xl_cdata.xl_rx_chain[i].xl_map);
bus_dmamap_destroy(sc->xl_mtag,
sc->xl_cdata.xl_rx_chain[i].xl_map);
m_freem(sc->xl_cdata.xl_rx_chain[i].xl_mbuf);
sc->xl_cdata.xl_rx_chain[i].xl_mbuf = NULL;
}
}
bzero(sc->xl_ldata.xl_rx_list, XL_RX_LIST_SZ);
/*
* Free the TX list buffers.
*/
for (i = 0; i < XL_TX_LIST_CNT; i++) {
if (sc->xl_cdata.xl_tx_chain[i].xl_mbuf != NULL) {
bus_dmamap_unload(sc->xl_mtag,
sc->xl_cdata.xl_tx_chain[i].xl_map);
bus_dmamap_destroy(sc->xl_mtag,
sc->xl_cdata.xl_tx_chain[i].xl_map);
m_freem(sc->xl_cdata.xl_tx_chain[i].xl_mbuf);
sc->xl_cdata.xl_tx_chain[i].xl_mbuf = NULL;
}
}
bzero(sc->xl_ldata.xl_tx_list, XL_TX_LIST_SZ);
ifp->if_flags &= ~(IFF_RUNNING | IFF_OACTIVE);
XL_UNLOCK(sc);
return;
}
/*
* Stop all chip I/O so that the kernel's probe routines don't
* get confused by errant DMAs when rebooting.
*/
static void
xl_shutdown(dev)
device_t dev;
{
struct xl_softc *sc;
sc = device_get_softc(dev);
XL_LOCK(sc);
xl_reset(sc);
xl_stop(sc);
XL_UNLOCK(sc);
return;
}
static int
xl_suspend(dev)
device_t dev;
{
struct xl_softc *sc;
sc = device_get_softc(dev);
XL_LOCK(sc);
xl_stop(sc);
XL_UNLOCK(sc);
return(0);
}
static int
xl_resume(dev)
device_t dev;
{
struct xl_softc *sc;
struct ifnet *ifp;
sc = device_get_softc(dev);
XL_LOCK(sc);
ifp = &sc->arpcom.ac_if;
xl_reset(sc);
if (ifp->if_flags & IFF_UP)
xl_init(sc);
XL_UNLOCK(sc);
return(0);
}
Reference in New Issue View Git Blame Copy Permalink