FreeBSD src
a1736be349
This includes a new summary mode (-s) for camcontrol defects that quickly tells the user the most important thing: how many defects are in the requested list. The actual location of the defects is less important. Modern drives frequently have more than the 8191 defects that can be reported by the READ DEFECT DATA (10) command. If they don't have that many grown defects, they certainly have more than 8191 defects in the primary (i.e. factory) defect list. The READ DEFECT DATA (12) command allows for longer parameter lists, as well as indexing into the list of defects, and so allows reporting many more defects. This has been tested with HGST drives and Seagate drives, but does not fully work with Seagate drives. Once I have a Seagate spec I may be able to determine whether it is possible to make it work with Seagate drives. scsi_da.h: Add a definition for the new long block defect format. Add bit and mask definitions for the new extended physical sector and bytes from index defect formats. Add a prototype for the new scsi_read_defects() CDB building function. scsi_da.c: Add a new scsi_read_defects() CDB building function. camcontrol(8) was previously composing CDBs manually. This is long overdue. camcontrol.c: Revamp the camcontrol defects subcommand. We now go through multiple stages in trying to get defect data off the drive while avoiding various drive firmware quirks. We start off by requesting the defect header with the 10 byte command. If we're in summary mode (-s) and the drive reports fewer defects than can be represented in the 10 byte header, we're done. Otherwise, we know that we need to issue the 12 byte command if the drive reports the maximum number of defects. If we're in summary mode, we're done if we get a good response back when asking for the 12 byte header. If the user has asked for the full list, then we use the address descriptor index field in the 12 byte CDB to step through the list in 64K chunks. 64K is small enough to work with most any ancient or modern SCSI controller. Add support for printing the new long block defect format, as well as the extended physical sector and bytes from index formats. I don't have any drives that support the new formats. Add a hexadecimal output format that can be turned on with -X. Add a quiet mode (-q) that can be turned on with the summary mode (-s) to just print out a number. Revamp the error detection and recovery code for the defects command to work with HGST drives. Call the new scsi_read_defects() CDB building function instead of rolling the CDB ourselves. Pay attention to the residual from the defect list request when printing it out, so we don't run off the end of the list. Use the new scsi_nv library routines to convert from strings to numbers and back. camcontrol.8: Document the new defect formats (longblock, extbfi, extphys) and command line options (-q, -s, -S and -X) for the defects subcommand. Explain a little more about what drives generally do and don't support. Sponsored by: Spectra Logic MFC after: 1 week |
||
|---|---|---|
| bin | ||
| cddl | ||
| contrib | ||
| crypto | ||
| etc | ||
| games | ||
| gnu | ||
| include | ||
| kerberos5 | ||
| lib | ||
| libexec | ||
| release | ||
| rescue | ||
| sbin | ||
| secure | ||
| share | ||
| sys | ||
| tests | ||
| tools | ||
| usr.bin | ||
| usr.sbin | ||
| .arcconfig | ||
| .arclint | ||
| COPYRIGHT | ||
| LOCKS | ||
| MAINTAINERS | ||
| Makefile | ||
| Makefile.inc1 | ||
| ObsoleteFiles.inc | ||
| README | ||
| UPDATING | ||
This is the top level of the FreeBSD source directory. This file was last revised on: $FreeBSD$ For copyright information, please see the file COPYRIGHT in this directory (additional copyright information also exists for some sources in this tree - please see the specific source directories for more information). The Makefile in this directory supports a number of targets for building components (or all) of the FreeBSD source tree, the most commonly used one being ``world'', which rebuilds and installs everything in the FreeBSD system from the source tree except the kernel, the kernel-modules and the contents of /etc. The ``world'' target should only be used in cases where the source tree has not changed from the currently running version. See: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/makeworld.html for more information, including setting make(1) variables. The ``buildkernel'' and ``installkernel'' targets build and install the kernel and the modules (see below). Please see the top of the Makefile in this directory for more information on the standard build targets and compile-time flags. Building a kernel is a somewhat more involved process, documentation for which can be found at: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig.html And in the config(8) man page. Note: If you want to build and install the kernel with the ``buildkernel'' and ``installkernel'' targets, you might need to build world before. More information is available in the handbook. The sample kernel configuration files reside in the sys/<arch>/conf sub-directory (assuming that you've installed the kernel sources), the file named GENERIC being the one used to build your initial installation kernel. The file NOTES contains entries and documentation for all possible devices, not just those commonly used. It is the successor of the ancient LINT file, but in contrast to LINT, it is not buildable as a kernel but a pure reference and documentation file. Source Roadmap: --------------- bin System/user commands. cddl Various commands and libraries under the Common Development and Distribution License. contrib Packages contributed by 3rd parties. crypto Cryptography stuff (see crypto/README). etc Template files for /etc. games Amusements. gnu Various commands and libraries under the GNU Public License. Please see gnu/COPYING* for more information. include System include files. kerberos5 Kerberos5 (Heimdal) package. lib System libraries. libexec System daemons. release Release building Makefile & associated tools. rescue Build system for statically linked /rescue utilities. sbin System commands. secure Cryptographic libraries and commands. share Shared resources. sys Kernel sources. tools Utilities for regression testing and miscellaneous tasks. usr.bin User commands. usr.sbin System administration commands. For information on synchronizing your source tree with one or more of the FreeBSD Project's development branches, please see: http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/synching.html