d/freebsd-nq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
6a0ce00218
freebsd-nq/sys/dev/ata/ata-disk.c

676 lines
20 KiB
C
Raw Normal View History

Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/*-
* Copyright (c) 1998,1999 S<EFBFBD>ren Schmidt
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer,
* without modification, immediately at the beginning of the file.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. The name of the author may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
* IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
* OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
* NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
* DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
* THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
Divorce "dev_t" from the "major|minor" bitmap, which is now called udev_t in the kernel but still called dev_t in userland. Provide functions to manipulate both types: major() umajor() minor() uminor() makedev() umakedev() dev2udev() udev2dev() For now they're functions, they will become in-line functions after one of the next two steps in this process. Return major/minor/makedev to macro-hood for userland. Register a name in cdevsw[] for the "filedescriptor" driver. In the kernel the udev_t appears in places where we have the major/minor number combination, (ie: a potential device: we may not have the driver nor the device), like in inodes, vattr, cdevsw registration and so on, whereas the dev_t appears where we carry around a reference to a actual device. In the future the cdevsw and the aliased-from vnode will be hung directly from the dev_t, along with up to two softc pointers for the device driver and a few houskeeping bits. This will essentially replace the current "alias" check code (same buck, bigger bang). A little stunt has been provided to try to catch places where the wrong type is being used (dev_t vs udev_t), if you see something not working, #undef DEVT_FASCIST in kern/kern_conf.c and see if it makes a difference. If it does, please try to track it down (many hands make light work) or at least try to reproduce it as simply as possible, and describe how to do that. Without DEVT_FASCIST I belive this patch is a no-op. Stylistic/posixoid comments about the userland view of the <sys/*.h> files welcome now, from userland they now contain the end result. Next planned step: make all dev_t's refer to the same devsw[] which means convert BLK's to CHR's at the perimeter of the vnodes and other places where they enter the game (bootdev, mknod, sysctl).
1999-05-11 19:55:07 +00:00
* $Id: ata-disk.c,v 1.9 1999/05/07 16:37:06 peter Exp $
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
*/
#include "ata.h"
#include "atadisk.h"
#include "opt_devfs.h"
#if NATA > 0 && NATADISK > 0
#include <sys/param.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/proc.h>
#include <sys/device.h>
#include <sys/malloc.h>
#include <sys/buf.h>
#include <sys/disklabel.h>
#include <sys/diskslice.h>
#include <sys/devicestat.h>
#include <sys/fcntl.h>
#include <sys/conf.h>
#include <sys/stat.h>
#ifdef DEVFS
#include <sys/devfsext.h>
#endif
#include <machine/clock.h>
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#include <pci/pcivar.h>
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#include <i386/isa/isa.h>
#include <i386/isa/isa_device.h>
#include <dev/ata/ata-all.h>
#include <dev/ata/ata-disk.h>
static d_open_t adopen;
static d_close_t adclose;
static d_ioctl_t adioctl;
static d_strategy_t adstrategy;
static d_psize_t adpsize;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#define BDEV_MAJOR 30
#define CDEV_MAJOR 116
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static struct cdevsw ad_cdevsw = {
Introduce two functions: physread() and physwrite() and use these directly in *devsw[] rather than the 46 local copies of the same functions. (grog will do the same for vinum when he has time)
1999-05-07 07:03:47 +00:00
adopen, adclose, physread, physwrite,
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adioctl, nostop, nullreset, nodevtotty,
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#ifdef NOTYET /* the boot code needs to be fixed to boot arbitrary devices */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
seltrue, nommap, adstrategy, "ad",
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
#else
seltrue, nommap, adstrategy, "wd",
#endif
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
NULL, -1, nodump, adpsize,
D_DISK, 0, -1
};
/* misc defines */
Divorce "dev_t" from the "major|minor" bitmap, which is now called udev_t in the kernel but still called dev_t in userland. Provide functions to manipulate both types: major() umajor() minor() uminor() makedev() umakedev() dev2udev() udev2dev() For now they're functions, they will become in-line functions after one of the next two steps in this process. Return major/minor/makedev to macro-hood for userland. Register a name in cdevsw[] for the "filedescriptor" driver. In the kernel the udev_t appears in places where we have the major/minor number combination, (ie: a potential device: we may not have the driver nor the device), like in inodes, vattr, cdevsw registration and so on, whereas the dev_t appears where we carry around a reference to a actual device. In the future the cdevsw and the aliased-from vnode will be hung directly from the dev_t, along with up to two softc pointers for the device driver and a few houskeeping bits. This will essentially replace the current "alias" check code (same buck, bigger bang). A little stunt has been provided to try to catch places where the wrong type is being used (dev_t vs udev_t), if you see something not working, #undef DEVT_FASCIST in kern/kern_conf.c and see if it makes a difference. If it does, please try to track it down (many hands make light work) or at least try to reproduce it as simply as possible, and describe how to do that. Without DEVT_FASCIST I belive this patch is a no-op. Stylistic/posixoid comments about the userland view of the <sys/*.h> files welcome now, from userland they now contain the end result. Next planned step: make all dev_t's refer to the same devsw[] which means convert BLK's to CHR's at the perimeter of the vnodes and other places where they enter the game (bootdev, mknod, sysctl).
1999-05-11 19:55:07 +00:00
#define UNIT(dev) (minor(dev)>>3 & 0x1f) /* assume 8 minor # per unit */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#define NUNIT 16 /* max # of devices */
/* prototypes */
static void ad_attach(void *);
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
static int32_t ad_getparam(struct ad_softc *);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void ad_strategy(struct buf *);
static void ad_start(struct ad_softc *);
static void ad_sleep(struct ad_softc *, int8_t *);
static int8_t ad_version(u_int16_t);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
int32_t ad_timeout(char *data);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void ad_drvinit(void);
static struct ad_softc *adtab[NUNIT];
static int32_t adnlun = 0; /* number of config'd drives */
static struct intr_config_hook *ad_attach_hook;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
static __inline int
apiomode(struct ata_params *ap)
{
if ((ap->atavalid & 2) == 2) {
if ((ap->apiomodes & 2) == 2) return 4;
if ((ap->apiomodes & 1) == 1) return 3;
}
return -1;
}
static __inline int
wdmamode(struct ata_params *ap)
{
if ((ap->atavalid & 2) == 2) {
if ((ap->wdmamodes & 4) == 4) return 2;
if ((ap->wdmamodes & 2) == 2) return 1;
if ((ap->wdmamodes & 1) == 1) return 0;
}
return -1;
}
static __inline int
udmamode(struct ata_params *ap)
{
if ((ap->atavalid & 4) == 4) {
if ((ap->udmamodes & 4) == 4) return 2;
if ((ap->udmamodes & 2) == 2) return 1;
if ((ap->udmamodes & 1) == 1) return 0;
}
return -1;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void
ad_attach(void *notused)
{
struct ad_softc *adp;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
int32_t ctlr, dev, secsperint;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
int8_t model_buf[40+1];
int8_t revision_buf[8+1];
/* now, run through atadevices and look for ATA disks */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
for (ctlr=0; ctlr<MAXATA; ctlr++) {
if (!atadevices[ctlr]) continue;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
for (dev=0; dev<2; dev++) {
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
if (atadevices[ctlr]->devices &
(dev ? ATA_ATA_SLAVE : ATA_ATA_MASTER)) {
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
#ifdef ATA_STATIC_ID
adnlun = dev + ctlr * 2;
#endif
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp = adtab[adnlun];
if (adp)
printf("ad%d: unit already attached\n", adnlun);
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
if (!(adp = malloc(sizeof(struct ad_softc),
M_DEVBUF, M_NOWAIT))) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
printf("ad%d: failed to allocate driver storage\n", adnlun);
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
continue;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bzero(adp, sizeof(struct ad_softc));
adp->controller = atadevices[ctlr];
adp->unit = (dev == 0) ? ATA_MASTER : ATA_SLAVE;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adp->lun = adnlun;
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
if (ad_getparam(adp)) {
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
free(adp, M_DEVBUF);
continue;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->cylinders = adp->ata_parm->cylinders;
adp->heads = adp->ata_parm->heads;
adp->sectors = adp->ata_parm->sectors;
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
adp->total_secs = adp->cylinders * adp->heads * adp->sectors;
if (adp->cylinders == 16383 &&
adp->total_secs < adp->ata_parm->lbasize) {
adp->total_secs = adp->ata_parm->lbasize;
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adp->cylinders = adp->total_secs/(adp->heads*adp->sectors);
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (adp->ata_parm->atavalid & ATA_FLAG_54_58 &&
adp->ata_parm->lbasize)
adp->flags |= AD_F_USE_LBA;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* use multiple sectors/interrupt if device supports it */
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adp->transfersize = DEV_BSIZE;
secsperint = min(adp->ata_parm->nsecperint, 16);
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
if (!ata_command(adp->controller, adp->unit, ATA_C_SET_MULTI,
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
0, 0, 0, secsperint, 0, ATA_WAIT_INTR) &&
ata_wait(adp->controller, adp->unit, ATA_S_DRDY) >= 0)
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adp->transfersize *= secsperint;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* use DMA if drive & controller supports it */
if (!ata_dmainit(adp->controller, adp->unit,
apiomode(adp->ata_parm),
wdmamode(adp->ata_parm),
udmamode(adp->ata_parm)))
adp->flags |= AD_F_DMA_ENABLED;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bpack(adp->ata_parm->model, model_buf, sizeof(model_buf));
bpack(adp->ata_parm->revision, revision_buf,
sizeof(revision_buf));
printf("ad%d: <%s/%s> ATA-%c disk at ata%d as %s\n",
adnlun,
model_buf, revision_buf,
ad_version(adp->ata_parm->versmajor),
ctlr,
(adp->unit == ATA_MASTER) ? "master" : "slave ");
printf("ad%d: %luMB (%u sectors), "
"%u cyls, %u heads, %u S/T, %u B/S\n",
adnlun,
adp->total_secs / ((1024L * 1024L) / DEV_BSIZE),
adp->total_secs,
adp->cylinders,
adp->heads,
adp->sectors,
DEV_BSIZE);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
printf("ad%d: piomode=%d, dmamode=%d, udmamode=%d\n",
adnlun,
apiomode(adp->ata_parm),
wdmamode(adp->ata_parm),
udmamode(adp->ata_parm));
printf("ad%d: %d secs/int, %d depth queue, %s mode\n",
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adnlun, adp->transfersize / DEV_BSIZE,
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
adp->ata_parm->queuelen & 0x1f,
(adp->flags & AD_F_DMA_ENABLED) ? "DMA" :"PIO");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
devstat_add_entry(&adp->stats, "ad", adnlun, DEV_BSIZE,
DEVSTAT_NO_ORDERED_TAGS,
DEVSTAT_TYPE_DIRECT | DEVSTAT_TYPE_IF_IDE,
0x180);
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
#ifdef DEVFS
adp->cdevs_token = devfs_add_devswf(&ad_cdevsw,
dkmakeminor(adp->lun, 0, 0),
DV_CHR,
UID_ROOT, GID_OPERATOR,
0640, "rad%d", adp->lun);
adp->bdevs_token = devfs_add_devswf(&ad_cdevsw,
dkmakeminor(adp->lun, 0, 0),
DV_BLK,
UID_ROOT, GID_OPERATOR,
0640, "ad%d", adp->lun);
#endif
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bufq_init(&adp->queue);
adtab[adnlun++] = adp;
}
}
}
config_intrhook_disestablish(ad_attach_hook);
}
static int32_t
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
ad_getparam(struct ad_softc *adp)
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
{
struct ata_params *ata_parm;
int8_t buffer[DEV_BSIZE];
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* select drive */
outb(adp->controller->ioaddr + ATA_DRIVE, ATA_D_IBM | adp->unit);
DELAY(1);
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
ata_command(adp->controller, adp->unit, ATA_C_ATA_IDENTIFY,
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
0, 0, 0, 0, 0, ATA_WAIT_INTR);
if (ata_wait(adp->controller, adp->unit,
ATA_S_DRDY | ATA_S_DSC | ATA_S_DRQ))
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
return -1;
insw(adp->controller->ioaddr + ATA_DATA, buffer,
sizeof(buffer)/sizeof(int16_t));
ata_parm = malloc(sizeof(struct ata_params), M_DEVBUF, M_NOWAIT);
if (!ata_parm)
return -1;
bcopy(buffer, ata_parm, sizeof(struct ata_params));
bswap(ata_parm->model, sizeof(ata_parm->model));
btrim(ata_parm->model, sizeof(ata_parm->model));
bswap(ata_parm->revision, sizeof(ata_parm->revision));
btrim(ata_parm->revision, sizeof(ata_parm->revision));
adp->ata_parm = ata_parm;
return 0;
}
static int
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adopen(dev_t dev, int32_t flags, int32_t fmt, struct proc *p)
{
int32_t lun = UNIT(dev);
struct ad_softc *adp;
struct disklabel label;
int32_t error;
#ifdef AD_DEBUG
printf("adopen: lun=%d adnlun=%d\n", lun, adnlun);
#endif
if (lun >= adnlun || !(adp = adtab[lun]))
return ENXIO;
/* spinwait if anybody else is reading the disk label */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* is this needed anymore ?? SOS XXX */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
while (adp->flags & AD_F_LABELLING)
tsleep((caddr_t)&adp->flags, PZERO - 1, "adop1", 1);
/* protect agains label race */
adp->flags |= AD_F_LABELLING;
/* build disklabel and initilize slice tables */
bzero(&label, sizeof label);
label.d_secsize = DEV_BSIZE;
label.d_nsectors = adp->sectors;
label.d_ntracks = adp->heads;
label.d_ncylinders = adp->cylinders;
label.d_secpercyl = adp->sectors * adp->heads;
label.d_secperunit = adp->total_secs;
error = dsopen("ad", dev, fmt, 0, &adp->slices, &label, ad_strategy,
(ds_setgeom_t *)NULL, &ad_cdevsw);
adp->flags &= ~AD_F_LABELLING;
ad_sleep(adp, "adop2");
return error;
}
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
static int
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adclose(dev_t dev, int32_t flags, int32_t fmt, struct proc *p)
{
int32_t lun = UNIT(dev);
struct ad_softc *adp;
#ifdef AD_DEBUG
printf("adclose: lun=%d adnlun=%d\n", lun, adnlun);
#endif
if (lun >= adnlun || !(adp = adtab[lun]))
return ENXIO;
dsclose(dev, fmt, adp->slices);
return 0;
}
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
static int
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adioctl(dev_t dev, u_long cmd, caddr_t addr, int32_t flags, struct proc *p)
{
struct ad_softc *adp;
int32_t lun = UNIT(dev);
int32_t error = 0;
if (lun >= adnlun || !(adp = adtab[lun]))
return ENXIO;
ad_sleep(adp, "adioct");
error = dsioctl("sd", dev, cmd, addr, flags, &adp->slices,
ad_strategy, (ds_setgeom_t *)NULL);
if (error != ENOIOCTL)
return error;
return ENOTTY;
}
static void
adstrategy(struct buf *bp)
{
struct ad_softc *adp;
int32_t lun = UNIT(bp->b_dev);
int32_t s;
#ifdef AD_DEBUG
printf("adstrategy: entered\n");
#endif
if (lun >= adnlun || bp->b_blkno < 0 || !(adp = adtab[lun])
|| bp->b_bcount % DEV_BSIZE != 0) {
bp->b_error = EINVAL;
bp->b_flags |= B_ERROR;
Sixth update to the new ATA/ATAPI driver: Fixed problems: Promise controllers was not always set up correctly. Parantheses are a good thing, fixed. Some older CDROM's could hang the probe. Proberly wait for the drive to catch its breath after IDENTIFY. Some CD writers fails because they dont support rezero. Rearranged the code to not use rezero. Warnings now that we use EGCS. Fixed.
1999-04-10 18:53:35 +00:00
biodone(bp);
return;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Sixth update to the new ATA/ATAPI driver: Fixed problems: Promise controllers was not always set up correctly. Parantheses are a good thing, fixed. Some older CDROM's could hang the probe. Proberly wait for the drive to catch its breath after IDENTIFY. Some CD writers fails because they dont support rezero. Rearranged the code to not use rezero. Warnings now that we use EGCS. Fixed.
1999-04-10 18:53:35 +00:00
if (dscheck(bp, adp->slices) <= 0) {
biodone(bp);
return;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* hang around if somebody else is labelling */
if (adp->flags & AD_F_LABELLING)
ad_sleep(adp, "adlab");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
s = splbio();
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bufqdisksort(&adp->queue, bp);
if (!adp->active)
ad_start(adp);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (adp->controller->active == ATA_IDLE)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
ata_start(adp->controller);
splx(s);
return;
}
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
static int
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adpsize(dev_t dev)
{
struct ad_softc *adp;
int32_t lun = UNIT(dev);
if (lun >= adnlun || !(adp = adtab[lun]))
return -1;
return dssize(dev, &adp->slices, adopen, adclose);
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
static void
ad_strategy(struct buf *bp)
{
adstrategy(bp);
}
static void
ad_start(struct ad_softc *adp)
{
struct buf *bp;
#ifdef AD_DEBUG
printf("ad_start:\n");
#endif
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
if (adp->active) {
printf("ad_start: should newer be called when active\n"); /* SOS */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
return;
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (!(bp = bufq_first(&adp->queue)))
return;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* remove from drive queue */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bufq_remove(&adp->queue, bp);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
bp->b_driver1 = adp;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* link onto controller queue */
bufq_insert_tail(&adp->controller->ata_queue, bp);
/* mark the drive as busy */
adp->active = 1;
}
void
ad_transfer(struct buf *bp)
{
struct ad_softc *adp;
u_int32_t blknum, secsprcyl;
u_int32_t cylinder, head, sector, count, command;
/* get request params */
adp = bp->b_driver1;
/* calculate transfer details */
blknum = bp->b_pblkno + (adp->donecount / DEV_BSIZE);
#ifdef AD_DEBUG
printf("ad_transfer: blknum=%d\n", blknum);
#endif
if (adp->donecount == 0) {
/* setup transfer parameters */
adp->bytecount = bp->b_bcount;
count = howmany(adp->bytecount, DEV_BSIZE);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (adp->flags & AD_F_USE_LBA) {
sector = (blknum >> 0) & 0xff;
cylinder = (blknum >> 8) & 0xffff;
head = ((blknum >> 24) & 0xf) | ATA_D_LBA;
}
else {
secsprcyl = adp->sectors * adp->heads;
cylinder = blknum / secsprcyl;
head = (blknum % secsprcyl) / adp->sectors;
sector = (blknum % adp->sectors) + 1;
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* setup first transfer length */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->currentsize = min(adp->bytecount, adp->transfersize);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
devstat_start_transaction(&adp->stats);
/* does this drive & transfer work with DMA ? */
adp->flags &= ~AD_F_DMA_USED;
if ((adp->flags & AD_F_DMA_ENABLED) &&
!ata_dmasetup(adp->controller, adp->unit,
(void *)bp->b_data, adp->bytecount,
(bp->b_flags & B_READ))) {
adp->flags |= AD_F_DMA_USED;
command = (bp->b_flags&B_READ) ? ATA_C_READ_DMA : ATA_C_WRITE_DMA;
adp->currentsize = adp->bytecount;
}
/* does this drive support multi sector transfers ? */
else if (adp->currentsize > DEV_BSIZE)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
command = (bp->b_flags&B_READ) ? ATA_C_READ_MULTI:ATA_C_WRITE_MULTI;
else
command = (bp->b_flags&B_READ) ? ATA_C_READ : ATA_C_WRITE;
Now all actual probing of both ATA & ATAPI devices are done after interrupts are enabled, this kills the last "unwanted interrupts" (and there is no ugly hacks like in the old driver to avoid them). COmmand interrupt devices are now supported, this applies mostly to older CDROM's and apparently also the ZIP. Fixed problems: Number of total sectors wrong on some older drives. Fixed by not using the LBA size unless we know its valid. There has also been more general code clenaups, some reorgs also.
1999-03-05 09:43:30 +00:00
ata_command(adp->controller, adp->unit, command, cylinder, head,
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
sector, count, 0, ATA_IMMEDIATE);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* if this is a DMA transaction start it, return and wait for interrupt */
if (adp->flags & AD_F_DMA_USED) {
ata_dmastart(adp->controller, adp->unit);
#ifdef AD_DEBUG
printf("ad_transfer: return waiting for DMA interrupt\n");
#endif
return;
}
/* calculate this transfer length */
adp->currentsize = min(adp->bytecount, adp->transfersize);
/* if this is a PIO read operation, return and wait for interrupt */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (bp->b_flags & B_READ) {
#ifdef AD_DEBUG
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
printf("ad_transfer: return waiting for PIO read interrupt\n");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#endif
return;
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* ready to write PIO data ? */
if (ata_wait(adp->controller, adp->unit,
ATA_S_DRDY | ATA_S_DSC | ATA_S_DRQ) < 0) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
printf("ad_transfer: timeout waiting for DRQ");
}
/* output the data */
#if 0
outsw(adp->controller->ioaddr + ATA_DATA,
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
(void *)((uintptr_t)bp->b_data + adp->donecount),
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->currentsize / sizeof(int16_t));
#else
outsl(adp->controller->ioaddr + ATA_DATA,
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
(void *)((uintptr_t)bp->b_data + adp->donecount),
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->currentsize / sizeof(int32_t));
#endif
adp->bytecount -= adp->currentsize;
#ifdef AD_DEBUG
printf("ad_transfer: return wrote data\n");
#endif
}
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
int32_t
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
ad_interrupt(struct buf *bp)
{
struct ad_softc *adp = bp->b_driver1;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
int32_t dma_stat = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* finish DMA transfer */
if (adp->flags & AD_F_DMA_USED) {
if (!(ata_dmastatus(adp->controller, adp->unit) & ATA_BMSTAT_INTERRUPT)){
printf("extra SMP interrupt\n");
return ATA_OP_CONTINUES;
}
dma_stat = ata_dmadone(adp->controller, adp->unit);
}
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* get drive status */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (ata_wait(adp->controller, adp->unit, 0) < 0)
printf("ad_interrupt: timeout waiting for status");
if (adp->controller->status & (ATA_S_ERROR | ATA_S_CORR) ||
(adp->flags & AD_F_DMA_USED && dma_stat != ATA_BMSTAT_INTERRUPT)) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
oops:
printf("ad%d: status=%02x error=%02x\n",
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
adp->lun, adp->controller->status, adp->controller->error);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (adp->controller->status & ATA_S_ERROR) {
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
printf("ad_interrupt: hard error\n");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
bp->b_error = EIO;
bp->b_flags |= B_ERROR;
}
if (adp->controller->status & ATA_S_CORR)
Added driver to support ATAPI floppies ie LS-120 & ZIP drives. Added "options ATA_STATIC_ID" that wires ATA disks like the old wd driver. Fixed problems: Dont use more sectors/intr than the drive supports. Fix announce of > 8.4G disks. Dont call ad_interrupt/ad_transfer when no disks config'd. Use the right page# for CDR write mode params. Fix breakage when no PCI support in kernel. Implement DEVFS stuff. General code clenaup.
1999-03-03 21:10:29 +00:00
printf("ad_interrupt: soft ECC\n");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* if this was a PIO read operation, get the data */
if (adp->active && !(adp->flags & AD_F_DMA_USED) &&
((bp->b_flags & (B_READ | B_ERROR)) == B_READ)) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* ready to receive data? */
if ((adp->controller->status & (ATA_S_DRDY | ATA_S_DSC | ATA_S_DRQ))
!= (ATA_S_DRDY | ATA_S_DSC | ATA_S_DRQ))
printf("ad_interrupt: read interrupt arrived early");
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (ata_wait(adp->controller, adp->unit,
ATA_S_DRDY | ATA_S_DSC | ATA_S_DRQ) != 0){
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
printf("ad_interrupt: read error detected late");
goto oops;
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* data ready, read in */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#if 0
insw(adp->controller->ioaddr + ATA_DATA,
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
(void *)((uintptr_t)bp->b_data + adp->donecount),
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->currentsize / sizeof(int16_t));
#else
insl(adp->controller->ioaddr + ATA_DATA,
Bring the 'new-bus' to the i386. This extensively changes the way the i386 platform boots, it is no longer ISA-centric, and is fully dynamic. Most old drivers compile and run without modification via 'compatability shims' to enable a smoother transition. eisa, isapnp and pccard* are not yet using the new resource manager. Once fully converted, all drivers will be loadable, including PCI and ISA. (Some other changes appear to have snuck in, including a port of Soren's ATA driver to the Alpha. Soren, back this out if you need to.) This is a checkpoint of work-in-progress, but is quite functional. The bulk of the work was done over the last few years by Doug Rabson and Garrett Wollman. Approved by: core
1999-04-16 21:22:55 +00:00
(void *)((uintptr_t)bp->b_data + adp->donecount),
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->currentsize / sizeof(int32_t));
#endif
adp->bytecount -= adp->currentsize;
#ifdef AD_DEBUG
printf("ad_interrupt: read in data\n");
#endif
}
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
/* if this was a DMA operation finish up */
if (adp->active && (adp->flags & AD_F_DMA_USED) && !(bp->b_flags & B_ERROR))
adp->bytecount -= adp->currentsize;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
/* finish up this tranfer, check for more work on this buffer */
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
if (adp->controller->active == ATA_ACTIVE_ATA) {
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if ((bp->b_flags & B_ERROR) == 0) {
adp->donecount += adp->currentsize;
#ifdef AD_DEBUG
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
printf("ad_interrupt: %s op OK\n", (bp->b_flags & B_READ)?"R":"W");
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
#endif
if (adp->bytecount > 0) {
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
ad_transfer(bp);
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
return ATA_OP_CONTINUES;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
}
bufq_remove(&adp->controller->ata_queue, bp);
bp->b_resid = bp->b_bcount - adp->donecount;
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
biodone(bp);
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
devstat_end_transaction(&adp->stats, bp->b_bcount - bp->b_resid,
DEVSTAT_TAG_NONE,
(bp->b_flags & B_READ) ?
DEVSTAT_READ : DEVSTAT_WRITE);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
adp->donecount = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
adp->active = 0;
}
ad_start(adp);
#ifdef AD_DEBUG
printf("ad_interrupt: completed\n");
#endif
ZIP drives should now be working, I'm not sure about LS120 drives, reports on those most welcome! Fixed problems: Hang on probe on "fantom" devices. The probe now use a timeout to avoid hangs if no interrupt is recevied. There has also been more general code clenaups, and some reorgs.
1999-03-07 21:49:14 +00:00
return ATA_OP_FINISHED;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
}
static void
ad_sleep(struct ad_softc *adp, int8_t *mesg)
{
int32_t s = splbio();
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
while (adp->controller->active != ATA_IDLE)
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
tsleep((caddr_t)&adp->controller->active, PZERO - 1, mesg, 1);
splx(s);
}
static int8_t
ad_version(u_int16_t version)
{
int32_t bit;
if (version == 0xffff)
return '?';
for (bit = 15; bit >= 0; bit--)
if (version & (1<<bit))
return ('0' + bit);
return '?';
}
static void
ad_drvinit(void)
{
Sixth update to the new ATA/ATAPI driver: Fixed problems: Promise controllers was not always set up correctly. Parantheses are a good thing, fixed. Some older CDROM's could hang the probe. Proberly wait for the drive to catch its breath after IDENTIFY. Some CD writers fails because they dont support rezero. Rearranged the code to not use rezero. Warnings now that we use EGCS. Fixed.
1999-04-10 18:53:35 +00:00
static int32_t ad_devsw_installed = 0;
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
if (!ad_devsw_installed) {
cdevsw_add_generic(BDEV_MAJOR, CDEV_MAJOR, &ad_cdevsw);
Fourth update to the new ATA/ATAPI driver: Well, better late than newer, but things has been hectic around here, sorry for the long delay. DMA support has been added to the ATA disk driver. This only works on Intel PIIX3/4, Acer Aladdin and Promise controllers. The promise support works without the BIOS on the board, and timing modes are set to support up to UDMA speed. This solves the problems with having more than one promise controller in the same system. There is support for "generic" DMA, that might work on other controllers, but now you have been warned :) More chipset specific code will come soon, I have to find testers with the approbiate HW, more on that when I have it ready. The system now uses its own major numbers, please run MAKEDEV with the devices you need (ad?, acd?, afd?, ast?). For now the disk driver will also attach to the old wd major so one can at least boot without this step, but be warned, this will eventually go away. The bootblocks will have to be changed before one can boot directly from an "ad" device though. Fixed problems: All known hang problems should be solved The probe code has been sligthly changed, this should solve the reports I have lying around (I hope). Hangs when accessing ata & atapi device on the same channel simultaniously. A real braino in ata_start caused this, fixed. As usual USE AT YOUR OWN RISK!!, this is still pre alpha level code. Especially the DMA support can hose your disk real bad if anything goes wrong, agaiin you have been warned :) But please tell me how it works for you! Enjoy! -Søren
1999-03-28 18:57:20 +00:00
cdevsw_add_generic(0, 3, &ad_cdevsw); /* grap wd entries too */
Finally!! The much roumored replacement for our current IDE/ATA/ATAPI is materialising in the CVS repositories around the globe. So what does this bring us: A new reengineered ATA/ATAPI subsystem, that tries to overcome most of the deficiencies with the current drivers. It supports PCI as well as ISA devices without all the hackery in ide_pci.c to make PCI devices look like ISA counterparts. It doesn't have the excessive wait problem on probe, in fact you shouldn't notice any delay when your devices are getting probed. Probing and attaching of devices are postponed until interrupts are enabled (well almost, not finished yet for disks), making things alot cleaner. Improved performance, although DMA support is still WIP and not in this pre alpha release, worldstone is faster with the new driver compared to the old even with DMA. So what does it take away: There is NO support for old MFM/RLL/ESDI disks. There is NO support for bad144, if your disk is bad, ditch it, it has already outgrown its internal spare sectors, and is dying. For you to try this out, you will have to modify your kernel config file to use the "ata" controller instead of all wdc? entries. example: # for a PCI only system (most modern machines) controller ata0 device atadisk0 # ATA disks device atapicd0 # ATAPI CDROM's device atapist0 # ATAPI tapes #You should add the following on ISA systems: controller ata1 at isa? port "IO_WD1" bio irq 14 controller ata2 at isa? port "IO_WD2" bio irq 15 You can leave it all in there, the system knows how to manage. For now this driver reuses the device entries from the old system (that will probably change later), but remember that disks are now numbered in the sequence they are found (like the SCSI system) not as absolute positions as the old system. Although I have tested this on all the systems I can get my hands on, there might very well be gremlins in there, so use AT YOU OWN RISK!! This is still WIP, so there are lots of rough edges and unfinished things in there, and what I have in my lab might look very different from whats in CVS at any given time. So please have all eventual changes go through me, or chances are they just dissapears... I would very much like to hear from you, both good and bad news are very welcome. Enjoy!! -Søren
1999-03-01 21:19:19 +00:00
ad_devsw_installed = 1;
}
/* register callback for when interrupts are enabled */
if (!(ad_attach_hook =
(struct intr_config_hook *)malloc(sizeof(struct intr_config_hook),
M_TEMP, M_NOWAIT))) {
printf("ad: malloc attach_hook failed\n");
return;
}
bzero(ad_attach_hook, sizeof(struct intr_config_hook));
ad_attach_hook->ich_func = ad_attach;
if (config_intrhook_establish(ad_attach_hook) != 0) {
printf("ad: config_intrhook_establish failed\n");
free(ad_attach_hook, M_TEMP);
}
}
SYSINIT(addev, SI_SUB_DRIVERS, SI_ORDER_SECOND, ad_drvinit, NULL)
#endif /* NATA && NATADISK */
Reference in New Issue Copy Permalink