When AUTO_OBJ is enabled this change becomes redundant with the auto.obj.mk
check added in r325404. However, it is possible that new code is added
at some point between src.sys.obj.mk and auto.obj.mk that disables AUTO_OBJ.
That could leave make with a bogus and unsafe .OBJDIR in some cases.
Sponsored by: Dell EMC Isilon
auto.obj.mk is loaded before the Makefile which may have NO_OBJ set inside of
it. In that case we can't avoid creating the OBJDIR but we do need to avoid
using it. Fixing .OBJDIR in bsd.init.mk at least fixes all of the build .mk
files to have a proper .OBJDIR. It does not fix the Makefile itself but
usually if they have NO_OBJ set they are not inspecting ${.OBJDIR} anyhow.
It is ideal to only have this in bsd.init.mk and to remove it from bsd.obj.mk,
but then bsd.obj.mk would need to include bsd.init.mk. Doing something like
that would require more testing. It has been proposed that bsd.obj.mk not be
included directly but it has been possible for too long to do so to change it
at this point.
Note too that it may make sense to fix .OBJDIR even when AUTO_OBJ is not
enabled but the historical behavior has always been that NO_OBJ just avoids
running 'make obj', so .OBJDIR should already be .CURDIR.
Also while NO_OBJ seems like it should be removed at this point, it is not
always possible to fix Makefiles to properly use an .OBJDIR. The cost of
keeping NO_OBJ support is minimal.
Sponsored by: Dell EMC Isilon
This problem was caused by r325329 and r325350.
For the release(7) targets, some will run mm-mtree.sh which itself runs make
with a MAKEOBJDIRPREFIX. The execution of that script leaks OBJROOT,
MAKEOBJDIR, and MAKELEVEL=1 in the environment. This causes the mm-mtree makes
to not do some basic setup of OBJROOT and only use this special
MAKEOBJDIRPREFIX case which fails to empty out MAKEOBJDIRPREFIX for further
nested makes, such as a tree walk. If that tree walk sets OBJROOT/OBJTOP such
as r325329 is doing, then the wrong OBJDIRs end up being used due to the
unemptied MAKEOBJDIRPREFIX being preferred over the proper MAKEOBJDIR.
Pointyhat to: bdrewery
Sponsored by: Dell EMC Isilon
Under certain traffic pattern awg driver does not recover from TX queue
full condition. The actual source of the problem is not identified yet
but jmcneill@ agreed that bumping TX_MAX_SEGS to 20 is OK as a workaround
for the problem (NetBSD has it set to 128).
Also add some diagnostic printfs to prevent silent failure of bus_dma
functions in the future
PR will be kept open until root cause of the issue is identified and fixed
PR: 219927
Submitted by: Tom Vijlbrief <tvijlbrief@gmail.com>
Approved by: jmcneill
MFC after: 2 weeks
Forcing MK_AUTO_OBJ to no is not really needed since bsd.obj.mk is protected
against 'rm -rf ${.CURDIR}' already. It was also flawed as if MK_AUTO_OBJ=yes
was in the .MAKEOVERRIDES already then it just remained on.
Sponsored by: Dell EMC Isilon
If for any reason we cannot set .OBJDIR==_objdir as desired
use .CURDIR so that at least the classic
.if ${.OBJDIR} != ${.CURDIR}
works and dangerous misstakes can be avoided.
Reviewed by: bdrewery
respected.
Please notice that libcasper is already in ObsoleteFiles so we don't add it
again.
Reported by: Herbert J. Skuhra <herbert@mailbox.org>
Reviewed by: bdrewery@
Differential Revision: https://reviews.freebsd.org/D12918
costly PCI config space operations that slows down systems without the
hardware.
Many thanks to HighPoint for continued support of FreeBSD!
Submitted by: Steve Chang
Reported by: cperciva
MFC after: 2 weeks
We already pass -many to the assembler, and -me500 drops 64-bit instruction
handling, for some reason only breaking module building for 64-bit kernels.
Additionally, build with CTF for dtrace.
NO_OBJ has a very specific meaning in sub-directories in that no object
directory will be made. If a user wanted to skip the 'make obj' phase then
passing -DNO_OBJ would break all sub-directories from building properly. Using
NO_OBJ internally also causes issue with NO_OBJ handling being added in
share/mk/bsd.init.mk soon.
Sponsored by: Dell EMC Isilon
ubldr is the non-pie version of ubldr.bin, do not install two
copies of the same binary. This will allow us to remove ubldr
in the future.
All the u-boot ports know how to load ubldr.bin
Reviewed by: gjb (earlier version)
mt(1) man page.
LTO-8 Type M (also known as M8) is a pristine LTO-7 cartridge
formatted in a LTO-8 drive in a new, higher density format. It
has a separate density code, and is only readable in an LTO-8
drive.
lib/libmt/mtlib.c:
Add the LTO-8 Type M density code to the density table
in libmt.
usr.bin/mt/mt.1:
Add the LTO-8 Type M density code to the density
table in the mt(1) man page.
MFC after: 3 days
Sponsored by: Spectra Logic
make(1) invocations following the OBJDIR restructuring to
ensure the output arm SoC image is in the correct directory.
Sponsored by: The FreeBSD Foundation
Patches with very little context (-U0 and -U1) could get misapplied if
the file to be patched changes and a hunk is no longer applicable. Matching
with fuzz would be attempted and default to a match when we unexpectedly ran
out of context.
PR: 74127
Reviewed by: emaste, pfg
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D12631
For statically linked binaries, where all relocation are solved by static
linker, the linker expect that offset to TLS section is aligned. Additionaly,
to maintain absolute alignment, TLS TCB should by also aligned.
Obtained from: CheriBSD (initial version)
MFC after: 1 month
Reviewed by: brooks (previous version), kib
Differential Revision: https://reviews.freebsd.org/D12907
sys/dev/mpr/mpr_mapping.c
If _mapping_process_dpm_pg0 detects inconsistencies in the drive
mapping table (stored in the HBA's NVRAM), abort reading it and
continue to boot as if the mapping table were blank. I observed
such inconsistencies in several HBAs after upgrading firmware from
14.0.0.0 to 15.0.0.0.
Reviewed by: slm
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D12901
instead of malloc(). The SWAP objects are automagically freed when there are no
more consumers. This greatly simplifies the mmap logic inside CUSE(3) in the
kernel. This change fixes an issue where mmapped memory can accumulate and never
get freed, if many different mmap sizes are needed over time. Further this
change fixes memory leaks when the CUSE(3) kernel module is unloaded.
While at it make sure the CUSE_ALLOC_PAGES_MAX limit is treated as an exclusive
limit. CUSE(3) memory maps must be less than CUSE_ALLOC_PAGES_MAX number of pages.
Reviewed by: kib @
Differential Revision: https://reviews.freebsd.org/D11392
Sponsored by: Mellanox Technologies
MFC after: 1 week
This pointer is checked during the linux_dev_open() callback and does
not need to be NULL checked again. It should always be set for
character devices belonging to the "linuxcdevsw" and technically
there is no need to NULL check this pointer at all.
Suggested by: kib @
MFC after: 1 week
Sponsored by: Mellanox Technologies
{}'s around the if (c == EOF) block to prevent potential 'trailing else'
issues from being introduced when refactoring. As my gets_s() code
is based on this, it makes sense to fix the same issue here first
here and now, then do an svn copy again to capture this history).
Suggested by: ed@ in D12785
When trying to build world for MIPS64 with clang I was getting
linker errors because of a missing reference to std::get_new_handler().
It turns out std::get_new_handler() was not listed in Version.map so it was
marked as a local symbol in libcxxrt.so.
Reviewed by: theraven, brooks (mentor), emaste
Approved by: trasz
Obtained from: CheriBSD
Differential Revision: https://reviews.freebsd.org/D11925
key_updateaddresses() is used to update SA addresses and NAT-T
configuration in SADB_UPDATE message. This is done using cloning SA
content from old SA into new one. But addresses and NAT-T configuration
are taking from SADB_UPDATE message. Use newsa pointer to set NAT-T
properties into cloned SA.
PR: 223382
MFC after: 1 week
fine when a lot of different flows to be ciphered/deciphered are involved.
However, when a software crypto driver is used, there are
situations where we could benefit from making crypto(9) multi threaded:
- a single flow is to be ciphered: only one thread is used to cipher it,
- a single ESP flow is to be deciphered: only one thread is used to
decipher it.
The idea here is to call crypto(9) using a new mode (CRYPTO_F_ASYNC) to
dispatch the crypto jobs on multiple threads, if the underlying crypto
driver is working in synchronous mode.
Another flag is added (CRYPTO_F_ASYNC_KEEPORDER) to make crypto(9)
dispatch the crypto jobs in the order they are received (an additional
queue/thread is used), so that the packets are reinjected in the network
using the same order they were posted.
A new sysctl net.inet.ipsec.async_crypto can be used to activate
this new behavior (disabled by default).
Submitted by: Emeric Poupon <emeric.poupon@stormshield.eu>
Reviewed by: ae, jmg, jhb
Differential Revision: https://reviews.freebsd.org/D10680
Sponsored by: Stormshield
