2) use more robust way of link state handling for BCM5700 rev.B2 chip
3) workaround bug of some BCM570x chips which cause spurious "link up" messages
4) fix bug: some BCM570x chips was unable to detect link state changes after
ifconfig down/up sequence until any 'non-link related' interrupt generated.
(this happened due to pending internal link state attention which blocked
interrupt generation)
Approved by: glebius (mentor)
MFC after: 1 week
the the interface has been configured. I'm not sure how this could ever
have worked before, but it should be fixed now. Also break out the interrupt
degresitration function into it's own step.
before. The symptom is that the battery inform us its charge and discharge
at the same time...
* fix bst.rate to correctly output the (dis)charging rate. We'll use
the current average over one minute command and not the at_rate command.
Note that this method is not correct if the capacity_mode is set, but
since we don't set it ourself, it is not a problem.
The at_rate do not give the actual rate but is used to compute the
estimated time for (dis)charging a battery. We should actually
write an estimation of the actual rate using at_rate cmd and then
perform a read to the various estimators.
Approved by: njl
MFC after: 2 days
The minimum / maximum speed was way too low / high!
minspeed = 2000 - is this for real ?
maxspeed = 767999 - is this for real ?????
Wrap everything into 8000 - 48000 boundary, just to be safe.
MFC after: 3 days
- Mark MPSAFE since most of the locking procedures already implemented.
- Turn on inverted external amplifier sense flag for selected boards.
Tested by: bland
MFC after: 1 week
- Only update the rx ring consumer pointer after running through the rx loop,
not with each iteration through the loop.
- If possible, use a fast interupt handler instead of an ithread handler. Use
the interrupt handler to check and squelch the interrupt, then schedule a
taskqueue to do the actual work. This has three benefits:
- Eliminates the 'interrupt aliasing' problem found in many chipsets by
allowing the driver to mask the interrupt in the NIC instead of the
OS masking the interrupt in the APIC.
- Allows the driver to control the amount of work done in the interrupt
handler. This results in what I call 'adaptive polling', where you get
the latency benefits of a quick response to interrupts with the
interrupt mitigation and work partitioning of polling. Polling is still
an option in the driver, but I consider it orthogonal to this work.
- Don't hold the driver lock in the RX handler. The handler and all data
associated is effectively serialized already. This eliminates the cost of
dropping and reaquiring the lock for every receieved packet. The result
is much lower contention for the driver lock, resulting in lower CPU usage
and lower latency for interactive workloads.
The amount of work done in the taskqueue is controlled by the sysctl
dev.em.N.rx_processing_limit
and tunable
hw.em.rx_process_limit
Setting these to -1 effectively removes the limit.
The fast interrupt and taskqueue can be disabled by defining NO_EM_FASTINTR.
This work has been shown to increase fast-forwarding from ~570 kpps to
~750 kpps (note that the same NIC hardware seems unable to transmit more than
800 kpps, so this increase appears to be limited almost solely by the
hardware). Gains have been shown in other workloads, ranging from better
performance to elimination of over-saturation livelocks.
Thanks to Andre Opperman for his time and resources from his network
performance project in performing much of the testing. Thanks to Gleb
Smirnoff and Danny Braniss for their help in testing also.
Instead of dragging the entire ICH4/82801DB into this mess, select
only few boards based on pci subdevice / subvendor.
Tested by: Daisuke Orikasa <luxury-acura-3.5rl at nifty.com>
MFC after: 3 days
This is based on MCPC USB mobile phone guide line (MCPC-GL005)
Some other 3G system or so will work with this driver.
Kyocera PHS terminal (a.k.a. Kyopon) is known to work, which
is now supported by umodem(4) driver.
o record tsf in tx+rx frames
o switch from raw rssi to dbm for signal data and record both
signal and noise floor data (hacked for now to assume a fixed
noise floor; is correct with new hal)
o add monpass sysctl to control which rx'd frames are passed
up with errors; especially useful to see frames with CRC errors
o mark 'd packets w/ a CRC error with radiotap's BADFCS flag
Also add placeholder code for calibrating the noise floor when
using newer hals.
Reviewed by: avatar
MFC after: 1 week
better, I discovered sn doing too many pointer dereferences. This
driver would do silly things like:
sn_foo(struct ifnet *ifp)
{
struct sn_softc *sc = ifp->if_softc;
sc->ifp->mumble
/* Other stuff */
}
while /* other stuff */ usually needed sc, the extra deref isn't
needed. Eliminate a few dozen of them.
modules would have overlapping names.
- Only create /dev/si_control for unit 0.
Tested by: Joerg Lehners Joerg dot Lehners at informatik dot
uni-oldenburg dot de (on 6.x)
MFC after: 1 week
various pcib drivers to use their own private devclass_t variables for
their modules.
- Use the DEFINE_CLASS_0() macro to declare drivers for the various pcib
drivers while I'm here.
doesn't have any actual interrupts is listed in a _PRT entry, only print
a warning rather than panic'ing when we walk the _PRT's to build up count
of entries that reference a given link (the counts are used as weights so
that we can attempt to balance the load across IRQs used by link devices).
Instead, only panic if we attempt to use the _PRT entry to route an
interrupt for a device.
PR: i386/89545
Tested by: anders
- MPSAFE
- Fix / reorganize attach routine. Device specific initialization must
be done after generic bus / DMA setup. At last, Virtual Channels
(vchan) works as expected.
Note: Recent commit / fix against this driver proves that major enhancements
on the generic sound layer does indeed help to expose flaw within
device specific code. There are probably other drivers that need to
be addressed as well.
Tested by: barner
MFC after: 1 week
ifm_status and ifm_active. IFM_10_T gets set in the ifm_active field,
not in the ifm_status field, as far as I can tell.
Note: this was to enable a workaround that's rarely enabled. I don't know
how to corrupt my eeprom to test it, and would rather not know...
signal is received during the msleep, the msleep is retried
indefinitely as it just keeps returning ERESTART because of
the pending signal.
Instead, just don't PCATCH - the signal can wait.
Sponsored by: Sophos/ActiveState
requiried to keep consistent softc state before/after callback function
invocation and supposed to be sligntly faster than previous one as it
wouldn't incur callback overhead. With this change callback function
was gone.
- Decrease TI_MAXTXSEGS to 32 from 128. It seems that most mbuf chain
length is less than 32 and it would be re-packed with m_defrag(9) if
its chain length is larger than TI_MAXTXSEGS. This would protect ti(4)
against possible kernel stack overflow when txsegs[] is put on stack.
Alternatively, we can embed the txsegs[] into softc. However, that
would waste memory and make Tx/Rx speration hard when we want to
sperate Tx/Rx handlers to optimize locking.
- Fix dma map tracking used in Tx path. Previously it used the dma map
of the last mbuf chain in ti_txeof() which was incorrect as ti(4)
used dma map of the first mbuf chain when it loads a mbuf chain with
bus_dmamap_load_mbuf(9). Correct the bug by introducing queues that
keep track of active/inactive dma maps/mbuf chain.
- Use ti_txcnt to check whether driver need to set watchdog timer instead
of blidnly clearing the timer in ti_txeof().
- Remove the 3rd arg. of ti_encap(). Since ti(4) now caches the last
descriptor index(ti_tx_saved_prodidx) used in Tx there is no need to
pass it as a fuction arg.
- Change data type of producer/consumer index to int from u_int16_t in
order to remove implicit type conversions in Tx/Rx handlers.
- Check interface queue before getting a mbuf chain to reduce locking
overhead.
- Check number of available Tx descriptores to be 16 or higher in
ti_start(). This wouldn't protect Tx descriptor shortage but it would
reduce number of bus_dmamap_unload(9) calls in ti_encap() when we are
about to running out of Tx descriptors.
- Command NIC to send packets ony when the driver really has packets
enqueued. Previously it always set TI_MB_SENDPROD_IDX which would
command NIC to DMA Tx descriptors into NIC local memory regardless
of Tx descriptor changes.
Reviewed by: scottl
allocating a resource that's in the card itself.
Remove more now-redundant resource_list_add, and now-redunant code
that lives in the pci layer.
# This fixes the atheros card that I have which had its CIS in one of
# the BARs. Don't know yet if this fixes the amd64 issues reported.
USB HID device that allows to plug two PS2 controllers. This specific
device doesn't work yet but will as soon as we support devices with
multiple report IDs.
MFC after: 3 days
broken report descriptor. While I'm here, make all the other report
descriptors const to match the newly added one.
Obtained from: NetBSD
MFC after: 1 week
lack a report descriptor and don't use the standard interface class.
This patch works around these deficiencies so that the uhid(4) driver
can recognize and use those broken devices.
PR: usb/90141
Submitted by: Ed Schouten <ed@fxq.nl> (with minor mods from me)
MFC after: 1 week
force allocation of unallocated BARs (cardbus uses this to preallocate
everything). Add a prefetchmask to allow for busses that get prefetch
hints to set them. Addjust pci_add_map and pci_ata_maps to take a new
force flag which pci_add_resources will pass in. Implement 'force' in
pci_add_map. Write new value of allocated resource into the bar, if
the allocation succeeded (we should have done this before, but with
the new force the bug was very obvious).
This should reduce huge playback / recording latency for
applications that try to act smarter and manage their own
buffering (XMMS, Skype, etc.).
Note to Skype + via8xxx users: Remove previous hackish
"hint.pcm.<unit>.via_dxs_disabled" from kernel hint and see
whether this changes cure all those annoying sound issues.
try very hard to be perfect. However, these attempts broke down when
there were large numbers of resources. We'd not be able to map them all.
Instead, accept that we might pass more range to thse subbus than
might be optimal be able to compute. However, there's little harm in
this and it allows us to pass greater resources through.
# it has been suggested that we allocate a fixed amount of resources
# on attach and give it out upon request. This might not be a bad idea...
cardbus_cis.c to this file, some code was not merged and thus resource
list entries were invalid. They didn't have a resources attached to
them.
However, the problem was masked for some time later, because newer
resources list entries were added to the head of the list, and
resource_list_find() always returned the first matching resource list
entry. Usually the underlying driver allocated a valid resource and
added it to the head of the list, and invalid one wasn't used.
In rev. 1.174 of subr_bus.c the sorting of resource list entries was
reversed demasking the problem in cardbus_alloc_resources().
This commit fixes the problem returning back some code from
cardbus_cis.c, pre-1.49 revisions.
PR: kern/87114
PR: kern/90441
Hardware provided by: Vasily Olekhov <olekhov yandex.ru>
Reviewed by: imp
. remove unnecessay header files after Scott's bus_dma(9) commit.
. remove global variable tis which was introduced at the time of
zero_copy(9) changes. The variable tis was not used at all. The
same applyes to ti_links in softc so axe it.
. deregister variables.
. axe ti_vhandle and switch to use explicit register access for
accessing NIC local memory. Creates three variants of ti_mem to
read/write NIC local memory(ti_mem_read, ti_mem_write) and clearing
NIC local memory(ti_mem_zero). This greatly enhances code
readability and have ti(4) drop using shared memory scheme for
Tigon 1. As Tigon 1 switched to use explicit register access for Tx,
axe ti_tx_ring_nic/ti_cmd_ring in softc.(Tigon 2 used to host ring
scheme which means there is no need to access NIC local memory via
register access for Tx and NIC would DMA the modified Tx rings into
its local memory.) [1]
. introduce new macro TI_EVENT_*/TI_CMD_* to handle NIC envent/command.
Instead of using bit fields assginment for accessing the event, use
shift operations to set/get it. [1]
. add additional check for valid DMA tags in ti_free_dmamaps().
. add missing bus_dmamap_sync/bus_dmamap_unload in ti_free_*_ring_*.
. fix locking nits(MTX_RECURSE mutex) and make ti(4) MPSAFE.
. change data type of ti_rdata_phys to bus_addr_t and don't blindly
cast to uint32_t.
. rearrange detach path and make ti(4) survive during device detach.
. for Tigon 1, use explicit register access for checking Tx descriptors
in ti_encap()/ti_txeof(). [1]
. properly call bus_dmamap_sync(9) for updating statistics.
. remove extra semicolon in ti_encap()
. rewrite loading MAC address to work on strict-alignment architectures.
. move TI_RD_OFF macro to if_tireg.h
. axe ETHER_ALIGN as it's already defined in <net/ethernet.h>.
. make macros immuine from expansion by adding parenthesis and do-while.
. remove alpha specific hack as vtophys(9) is no longer used in ti(4)
after Scott's bus_dma(9) fix.
Reviewed by: scottl
Obtained from: OpenBSD [1]
POSIX. This also makes the struct correct we ever implement an i386-time64
architecture. Not that we need too.
Reviewed by: imp, brooks
Approved by: njl (acpica), des (no objects, touches procfs)
Tested with: make universe
if we need a valid MAC address (for probing the media for example) before
ether_ifattach() has been called since IF_LLADDR() is NULL then.
Tested by: tisco
except for BGE_CHIPID_BCM5700_B0, which is buggy.
- All bge(4) supported hardware, has a bug that produces incorrect checksums
on Ethernet runts. However, in case of a transmitted packet, the latter can
be padded with zeroes, and the checksum would be correct. (Probably chip
includes the pad data into checksum). In case of receive, we just don't
trust checksum data in received runts.
Obtained from: NetBSD (jonathan) via Mihail Balikov
Previously it always returned 0 which means success regardless of
EEPROM status.
While here, add a check whether EEPROM read is successful.
Submitted by: jkim
- removed unused funtion bge_handle_events().
- removed bus_dmamap_destroy(9) calls for DMA maps created by
bus_dmamem_alloc(9). This should fix panics seen on sparc64
in device detach.
- added check for parent DMA tag creation.
- switched to use __NO_STRICT_ALIGNMENT as bge(4) supports all
architectures.
- added missing bus_dmamap_sync(9) in bge_txeof().
- added missing bus_dmamap_sync(9) in bge_encap().
- corrected memory synchronization operation on status block.
As the driver just read status block that was DMAed by NIC it
should use BUS_DMASYNC_POSTREAD. Likewise the driver does not
need to write status block back, so remove unnecessary
bus_dmamap_sync(9) calls in bge_intr().
- corrected memory synchronization operation on RX return ring.
The driver only read the block so remove unnecessary
bus_dmamap_sync(9) in bge_rxeof().
- force bus_dmamap_sync(9) for only modified descriptors. Blindly
synching all desciptor rings would reduce performance.
- call bus_dmamap_sync(9) for DMA maps that were modified in bge_rxeof().
Reviewed by: jkim(initial version)
Tested by: glebius(i386), jkim(amd64 initial version)
the addition of pci_find_extcap().
- Change the drm drivers to attach to vgapci. This is #ifdef'd so the
code can be shared across branches.
- Use pci_find_extcap() to look for AGP and PCIE capabilities in drm.
- GC all the drmsub stuff for i810/i830/i915. The agp and drm devices are
now both children of vgapci.
as a bus so that other drivers such as drm(4), acpi_video(4), and agp(4)
can attach to it thus allowing multiple drivers for the same device. It
also removes the need for the drmsub hack for the i8[13]0/i915 drm and agp
drivers.
attach to the hostb driver instead. This means that agp can now be loaded
at runtime (in theory at least). Also, the drivers no longer have to
explicity call device_verbose() to cancel out any earlier calls to
device_quiet() by the hostb(4) driver (this shows a limitation in new-bus,
drivers really shouldn't be doing device_quiet() until they know they are
going to drive that device, i.e. in attach).
duplicated anyways) and into a single MI driver. Extend the driver a bit
to implement the bus and PCI kobj interfaces such that other drivers can
attach to it and transparently act as if their parent device is the PCI
bus (for the most part).
drivers already map sections into KVA as needed anyway. Note that this
will probably break the nvidia driver, but I will coordinate to get that
fixed.
MFC after: 2 weeks
to search for a specific extended capability. If the specified capability
is found for the given device, then the function returns success and
optionally returns the offset of that capability. If the capability is
not found, the function returns an error.
we can cache its value in the softc. Eliminates one PCI register
write per call to bge_start().
A 1.8% speedup for UDP_RR test on my old box.
Obtained from: NetBSD(jonathan) via delphij
case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
command. This fixes some weird booting issues on newer versions
of the firmware on the MSA20.
Reported by: Philippe Pegon <Philippe dot Pegon at crc dot u-strasbg dot fr>
- Give up endianess support and switch to native-endian format for
accessing hardware structures. In fact embedded processor for
BCM57xx is big-endian architure(MIPS) and it requires native-endian
format for NIC structures.The NIC performs necessary byte/word
swapping depending on programmed endian type.
- With above changes all htole16/htole32 calls were gone.
- Remove bge_vhandle member in softc and changed to use explicit
register access. This may add additional performance penalty
that than that of previous memory access. But most of the access
is performed on initialization phase(e.g. RCB setup), it would be
negligible.
Due to incorrect use of bus_dma(9) in bge(4) it still panics sparc64
system in device detach path. The issue would be fixed in next patch.
Reviewed by: jkim (initial version)
Silence from: ps
Tested by: glebius
Obtained from: NetBSD via OpenBSD
