At initialization, hc_source_mask only includes non-Pure sources.
The patch changes source registration to enable the registered source in the
hc_source_mask bitmask. This mask governs which sources are harvested.
This patch also disallows userspace from disabling such sources.
PR: 222807
Submitted by: W. Dean Freeman <badfilemagic AT gmail.com>
Reviewed by: jmg (earlier version), delphij
Approved by: secteam (delphij)
Obtained from: HBSD 0054e3e170e083811acc9f3b637f8be8a86c03e7
Security: yes
Differential Revision: https://reviews.freebsd.org/D12611
Changes since 1.16.26.0 for all three firmwares are listed below. This
list was obtained from the Release Notes of the Chelsio Unified Wire
v3.5.05 release for Linux.
T6 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed a fw crash when configured traffic rate limit is less than 10kbps.
- Fixed traffic rate limiting for smaller traffic rate value.
ETH:
- Fixed 40G link failure when interface is toggled.
- Fixed adapter crash when interface is toggled during traffic.
- Fixed 25G link failure when PEER only supports consortium mode autoneg
for 25G.
- Fixed 100G optics link failure when cable is plugged in after bringing up
the interface.
- Enable RS FEC as default if speed is 100G.
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
- Fixed iWARP SRQ reuse failure.
FOiSCSI:
- Fixed vlan interface ping failure.
- Fixed target discovery failures.
- Fixed mutual chap login failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed fw crash caused by MC parity error in SO adapters.
- Generate Timer0Int interrupt if fw crashes due to unaligned access error. Host
driver must look into PCIE_FW register to see if any fw fatal error has
encountered. If PCIE_FW doesn't indicate any error then driver must ignore this
interrupt.
- Fixed receive buffer threshold settings which was resulting in error frames on
receive side.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed improper LED behaviour for blink test and when traffic is running.
- Removed storage of previous fec settings from fw. Driver needs to pass the user
settings whenever a new module is plugged in as fw resets these when a module is
unplugged.
OFLD
- OVS offload: TP cache is flushed periodically to get the accuate filters stats
(hit count).
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- VNI support added for filtering. New entry_type FW_VI_MAC_TYPE_EXACTMAC_VNI
added to FW_VI_MAC_CMD.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
- HMA (Host memory access) support added. New FW_HMA_CMD and
FW_PARAMS_PARAM_DEV_HMA_SIZE added to query and configure the HMA. It
enables the memfree support (256 connections) for iwarp.
- PTP support enabled.
ETH:
- Added consortium mode 50G support.
- Added the ability to allow only selected speeds to be advertised during auto
negotiation.
- Increased port capability from 16 to 32 bits to support more speeds.
FW_PARAMS_PARAM_PFVF_PORT_CAPS32 added to query whether fw supports 16 or 32
bit port capability.
OFLD:
- RDMA Write with immediate support added (iwarp 2.0 feature)
- FW_TLS_KEYCTX_TX_WR removed and security key management moved to driver.
- 256 offloaded connections support for iwarp on SO adapters.
iSCSI:
- New param FW_PARAMS_PARAM_DEV_PPOD_EDRAM added for iscsi ppod configuration
in EDRAM (performance improvement).
FOiSCSI:
- iSCSI Command offload target support added.
FOFCoE:
- FCoE support enabled.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
- Fixed DDR3/DDR4 ECC errors.
- Fixed an FLR issue where FLR completion was going to host before FLR
processing is finished in fw.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
- Fixed false link up when peer interface was brought down.
- Enabling RS FEC by default for 100Gbase-SR4 according to 802.3BJ standard.
- Fixed bugs related to negotiated fec based local/peer fec ability and request.
- Fixed auto-neg failure with few switches.
- T6 Performance improvement fixes.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
- T6 Crypto Coprocessor mode bug fixes.
- T6 Crypto TLS-inline mode bug fixes.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
ETH:
- Added broadcom consortium next page support for 25G CR.
This can be enabled using flags=an_brcm option in the t6-config.txt file.
- Added spider mode support.
- Added support for 10G-BaseT converter sfp+ module.
- Added support for additional 25G/100G cables.
- Added support to enable/disable auto-neg using ethtool.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
Fixes
-----
BASE:
- Fixed DDR4 uncorrectable errors.
ETH:
- Enabled link auto negotiation (AN) by default in config file.
- Added AN and FEC control api. Host driver and application can enable/disable
AN and FEC.
ENHANCEMENTS
------------
BASE:
- Enabled High priorty filter.
- Added T6425 adapter support.
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- Set multiple fec values only if AN is enabled in config file and when module
is connected.
- Fixed intermittent DDR3/4 ECC errors.
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
ETH:
- Made devlog more verbose by printing cable information in redable form.
- Updated AN settings to work with more 25G/100G switches.
- Added support for more SFP28/QSFP28 cables.
- Fixed an issue of link going down after few hours of idle time.
OFLD:
- Fixed an issue in TLS which was causing fw crash on running TLS traffic.
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T5 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed offload memory overcommit in case of SO adapter.
ETH:
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed an FLR issue which was causing error when VF attached VM was powered on.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed T580 link failure with few switches which take more time for
establishing link.
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
FOiSCSI:
- iSCSI Command offload target support added.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
ENHANCEMENTS
------------
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T4 Firmware
+++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
ETH:
- Fixed DCBX configuration refresh failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
ENHANCEMENTS
------------
BASE:
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
SUN8I and SUN50I (H3, H5, A83T and A64) have a second clock controller
unit. It controls the clocks for the second gpio controller, the IR
controller etc ...
Support for A83T is not supported.
Tested On: OrangePi One, Pine64
Lookups of the sort are rare compared to regular ones and succesfull ones
result in removing entries from the cache.
In the current code buckets are rlocked and a trylock dance is performed,
which can fail and cause a restart. Fixing it will require a little bit
of surgery and in order to keep the code maintaineable the 2 cases have
to split.
MFC after: 1 week
If VIMAGE is present we can start jails with their own pf instance. This
makes it fairly easy to run tests.
For example, this basic test verifies that drop/pass and icmp
classification works. It's a basic sanity test for pf, and hopefully an
example on how to write more pf tests.
The tests are skipped if VIMAGE is not enabled.
This work is inspired by the GSoC work of Panagiotes Mousikides.
Differential Revision: https://reviews.freebsd.org/D12580
The later fields of the harvest_event structure are predictable and provide
little value to the entropy pool. Only feed in the relatively high entropy
counter and explicit entropy buffer to increase measured input entropy.
See also:
https://people.freebsd.org/~jmg/vbsdcon_2017_ddfreebsdrng_slides.pdf
PR: 222807
Submitted by: W. Dean Freeman <badfilemagic AT gmail.com>
Reviewed by: jmg (earlier version), delphij
Approved by: secteam (delphij)
Obtained from: HBSD 8d809124d563937edd84c9c9d5494406e359c55c
Security: no -- low entropy marginal input has no known negative affect on pool quality
Differential Revision: https://reviews.freebsd.org/D12610
'last' is the sector number of the last usable sector. Sector
numbers start with 0. As such, 'last' is always 1 less than
the count of sectors and aligning 'last' down as-is means that
the number of free sectors is pessimized by 'alignment - 1' if
the number of usable sectors was already a multiple of the
alignment. Consequently, gpart(8) failed to create a partition
when the alignment and size were such that it would extend to
the end of the disk.
Previously it just didn't work at all - kvm_getprocs(3) doesn't update
the &nentries when it returns NULL. The end result was that ps(1) showed
garbage data instead of reporting kinfo_proc size mismatch.
Reviewed by: cem
Obtained from: CheriBSD
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12414
Provide consistent snapshot of the requested descriptors by preventing
other threads from modifying LDT while we fetch the data, lock dt_lock
around the read. Copy the data into intermediate buffer, which is
copied out after the lock is dropped.
Comparing with the amd64 version, the read is done byte by byte, since
there is no atomic 64bit read (cmpxchg8b method is too heavy comparing
with the avoided issues).
Improve overflow checking for the descriptors range calculations and
remove unneeded casts. Use unsigned types for sizes.
Allow zero num argument to i386_get_ldt() and i386_set_ldt(). This
case is handled naturally by the code flow.
Reviewed by: bde
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Apply authenticated user context after update of wtmp(5) at start of session,
so that ftpd process is not killed by kernel with SIGXFSZ when user has
"filesize" limit lower than size of system wtmp file. Same applies
to session finalization: revert to super-user context before update of wtmp.
If ftpd hits limit while writing a file at user request,
do not get killed with SIGXFSZ instantly but apparently ignore the signal,
process error and report it to the user, and continue with the session.
PR: 143570
Approved by: avg (mentor), mav (mentor)
MFC after: 1 week
enough processors. This isn't ideal, because one could still compile
MACHINE_ARCH armv6, but with armv7 options enabled. We don't normally
do that, and it's a bit of an edge case so accept the less than ideal
solution here in the absence of something better.
Reported by: strejda@
Sponsored by: Netflix
Move the retrieval of the image information into loader's main instead
of doing it in efizfs.c
Differential Revision: https://reviews.freebsd.org/D12564
Submitted by: Eric McCorkle
efi_devpath_is_prefix determines if a path matches a passed-in prefix.
Differential Revision: https://reviews.freebsd.org/D12564
Submitted by: Eric McCorkle
When using the default address list nam is still valid, the code in
r324054 assumed that is was NULL.
Reported by: Guy Yur <guyyur@gmail.com>
Tested by: Guy Yur <guyyur@gmail.com>
This file shouldn't be modified manually but well, I did it in my previous
commit. So go down further the rabbit hole so as to at least keep some
consistency.
Reported by: bapt
If they are still needed, you can find them in the net/bsdrcmds port.
This was proposed June, 20th and approved by various committers [1].
They have been marked as deprecated on CURRENT in r320644 [2] on July, 4th.
Both stable/11 and release/11.1 contain the deprecation notice (thanks to
allanjude@).
Note that ruptime(1)/rwho(1)/rwhod(8) were initially thought to be part of
rcmds but this was a mistake and those are therefore NOT removed.
[1] https://lists.freebsd.org/pipermail/freebsd-arch/2017-June/018239.html
[2] https://svnweb.freebsd.org/base?view=revision&revision=320644
Reviewed by: bapt, brooks
Differential Revision: https://reviews.freebsd.org/D12573
The upstream has converted their manual page to the same format as we
have, so we can use the upstream version with minimal modifications.
The current modifications are:
- different zpool.cache path
- different manual sections for zdb, zfs, zpool commands
igor reports a few minor issues, it would be nice to fix them both in
FreeBSD and in the upstream.
MFC after: 3 weeks
illumos/illumos-gate@4923c69fdd4923c69fdd
FreeBSD note: the manual page is to be updated separately.
https://www.illumos.org/issues/8067
Add an option to zdb to print a literal embedded block pointer supplied on the
command line:
zdb -E [-A] word0:word1:...:word15
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Matthew Ahrens <mahrens@delphix.com>
MFC after: 3 weeks
illumos/illumos-gate@ed4e7a6a5ced4e7a6a5chttps://www.illumos.org/issues/7340
When -o origin=<snapshot> is specified as part of a ZFS receive, that origin
should override the automatic detection in libzfs.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Paul Dagnelie <pcd@delphix.com>
MFC after: 3 weeks
illumos/illumos-gate@d5f26ad812d5f26ad812https://www.illumos.org/issues/5142
the current libzfs only allows simple disk and mirror setup for boot pool, as
loader does support booting from raidz, this feature will remove raidz
restriction from boot pool setup.
FreeBSD note: we have long supported this feature, this commit only
removes a small difference in libzfs.
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@nexenta.com>
Reviewed by: Andrew Stormont <andyjstormont@gmail.com>
Reviewed by: Albert Lee <trisk@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Toomas Soome <tsoome@me.com>
MFC after: 3 weeks
illumos/illumos-gate@aab04418a7aab04418a7https://www.illumos.org/issues/6268
The zfs diff command presents a description of the changes that have occurred
to files within a filesystem between two snapshots. If a file is renamed, the
tool is capable of reporting this, e.g.:
cd /some/zfs/dataset/subdir
mv file0 file1
Will result in a diff record like:
R /some/zfs/dataset/subdir/file0 -> /some/zfs/dataset/subdir/file1
Unfortunately, it seems that rename detection only uses the base filename to
determine if a file has been renamed or simply modified. This leads to
misreporting only the original filename, omitting the more relevant destination
filename entirely. For example:
cd /some/zfs/dataset/subdir
mv file0 ../otherdir/file0
Will result in a diff entry:
M /some/zfs/dataset/subdir/file0
But it should really emit:
R /some/zfs/dataset/subdir/file0 -> /some/zfs/dataset/otherdir/file0
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Justin Gibbs <gibbs@scsiguy.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Joshua M. Clulow <josh@sysmgr.org>
MFC after: 3 weeks
illumos/illumos-gate@ad2760acbdad2760acbdhttps://www.illumos.org/issues/7571
ZFS displays the default value for non-present readonly numeric (and index)
properties. However, these properties default values are not meaningful.
Instead, we should display a "-", indicating that they are not present. For
example, on a version-12 pool, the usedby* properties are not available, but
they show up as the incorrect value "0":
1. zfs get all test12
...
test12 usedbysnapshots 0 -
test12 usedbydataset 0 -
test12 usedbychildren 0 -
test12 usedbyrefreservation 0 -
We will be introducing more sometimes-present numeric readonly properties, so
it would be nice to fix this.
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Matthew Ahrens <mahrens@delphix.com>
MFC after: 3 weeks
illumos/illumos-gate@dfd5965f7edfd5965f7e
FreeBSD note: the manual page is to be updated separately.
https://www.illumos.org/issues/6392
When given a pool name via -e, zdb would attempt an import. If it
failed, then it would attempt a verbatim import. This behavior is
not always desirable so a -V switch is added to zdb to control the
behavior. When specified, a verbatim import is done. Otherwise,
the behavior is as it was previously, except no verbatim import
is done on failure.
a5778ea242
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Yuri Pankov <yuri.pankov@gmail.com>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Richard Yao <ryao@gentoo.org>
MFC after: 3 weeks
illumos/illumos-gate@ed61ec1da9ed61ec1da9
FreeBSD note: this commit does not update the manual page.
The original change includes conversion of the manual page from *roff format
to mandoc format. So, it is hard to extract the content change from
that. I am going to replace our zdb manual page, which is an earlier
independent conversion, with a slighly modified version of the upstream page.
https://www.illumos.org/issues/6410
This is primarily intended to ease debugging & testing ZFS when one is only
interested in things like the on-disk location of a specific object's blocks,
but doesn't know their object id. This allows doing things like the following
(FreeBSD-based example):
# zpool create -f foo da0
# dd if=/dev/zero of=/foo/1 bs=1M count=4 >/dev/null 2>&1
# zpool export foo
# zdb -vvvvv -o "ZFS plain file" foo /1
Object lvl iblk dblk dsize lsize %full type
8 2 16K 128K 3.99M 4M 100.00 ZFS plain file (K=inherit) (Z=inherit)
168 bonus System attributes
dnode flags: USED_BYTES USERUSED_ACCOUNTED
dnode maxblkid: 31
path /1
uid 0
gid 0
atime Thu Apr 23 22:45:32 2015
mtime Thu Apr 23 22:45:32 2015
ctime Thu Apr 23 22:45:32 2015
crtime Thu Apr 23 22:45:32 2015
gen 7
mode 100644
size 4194304
parent 4
links 1
pflags 40800000004
Indirect blocks:
0 L1 DVA[0]=<0:c19200:600> DVA[1]=<0:10800019200:600> [L1 ZFS
plain file] fletcher4 lz4 LE contiguous unique double size=4000L/200P birth=7L/
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Will Andrews <will@freebsd.org>
Approved by: Dan McDonald <danmcd@omniti.com>
Author: Yuri Pankov <yuri.pankov@nexenta.com>
MFC after: 3 weeks
Transition all boards that support arm cortex CPUs to armv7. This
leaves two armv6 kernels in the tree. RPI-B, which uses the BCM2835
which has a ARM1176 core, and VERSATILEPB, which is a qemu board setup
around the time RPI-B went in. Copy std.armv6 to std.armv7, even
though that duplicates a lot of stuff. More work needs to be done to
sort out the duplication.
Differential Revision: https://reviews.freebsd.org/D12027
Make armv7 as a new MACHINE_ARCH.
Copy all the places we do armv6 and add armv7 as basically an
alias. clang appears to generate code for armv7 by default. armv7 hard
float isn't supported by the the in-tree gcc, so it hasn't been
updated to have a new default.
Support armv7 as a new valid MACHINE_ARCH (and by extension
TARGET_ARCH).
Add armv7 to the universe build.
Differential Revision: https://reviews.freebsd.org/D12010
This patch adds support for the Flexible File Layout to the pNFS client.
Although the patch is rather large, it should only affect NFS mounts
using the "pnfs" option against pNFS servers that do not support File
Layout.
There are still a couple of things missing from the Flexible File Layout
client implementation:
- The code does not yet do a LayoutReturn with I/O error stats when
I/O error(s) occur when attempting to do I/O on a DS.
This will be fixed in a future commit, since it is important for the
MDS to know that I/O on a DS is failing.
- The current code does writes and commits to mirror DSs serially.
Making them happen concurrently will be done in a future commit,
after discussion on freebsd-current@ on the best way to do this.
- The code does not handle NFSv4.0 DSs. Since there is no extant pNFS
server that implements NFSv4.0 DSs and NFSv4.1 DSs makes more sense
now, I don't intend to implement this until there is a need for it.
There is support for NFSv4.1 and NFSv3 DSs.
Previous code would always spin once before checking the lock. But a lock
with e.g. 6 readers is not going to become free in the duration of once spin
even if they start draining immediately.
Conservatively perform one for each reader.
Note that the total number of allowed spins is still extremely small and is
subject to change later.
MFC after: 1 week
