Introduce 2 new flags:
- FL_ENABLE_4B_ADDR (forces the use of 4-byte addresses)
- FL_DISABLE_4B_ADDR (forces the use of 3-byte addresses)
If an SPI flash chip is defined with FL_ENABLE_4B_ADDR in its flags,
then an 'Enter 4-byte mode' command is sent to the chip at attach time
and, later, all commands that require addressing are issued with 4-byte
addresses.
If an SPI flash chip is defined with FL_DISABLE_4B_ADDR in its flags,
then an 'Exit 4-byte mode' command is sent to the chip at attach time
and, later, all commands that require addressing are issued with 3-byte
addresses.
For chips that do not have any of these flags defined the behaviour is
unchanged.
This change also adds support for the MX25L25735F and MX25L25635E chips
(vendor id 0xc2, device id 0x2019), which support 4-byte mode and enables
4-byte mode for them. These are 256Mbit devices (32MiB) and, as such, can
only be fully addressed by using 4-byte addresses.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5808
the interface.
I know this may be unpopular, but iwn is not yet completely ready for
a transparent firmware restart. I have this thing panic my laptop
reliably because 11n state isn't kept in sync and the TX completion
path ends up trying to free a null node reference.
If there is an error different from ERESTART, there is some
chance that we may end up accessing an uninitialized value. This
doesn't seem likely/possible but initialize announce_buf[0],
just in case.
CID: 1006486
For the !gsp case there some chance of returning an uninitialized
return value. Prevent that from happening by initializing the
error value.
CID: 1006421
Previously this operation tried to unmount and remount children.
Also see https://www.illumos.org/issues/6428.
MFC after: 2 weeks
X-Needs-Upstreaming: illumos
When force-receiving a filesystem that was already mounted the re-created
filesystem is mounted despite -u flag.
Also see https://www.illumos.org/issues/6412.
PR: 204705
Tested by: Vladimir Krstulja <vlad-fbsd@acheronmedia.com>
MFC after: 2 weeks
X-Needs-Upstreaming: illumos
On FreeBSD VFS_HOLD/VN_RELE were mapped to MNT_REF/MNT_REL that
manipulate mnt_ref. But the job of properly maintaining the reference
count is already automatically performed by insmntque(9) and
delmntque(9). So, in effect all ZFS vnodes referenced the corresponding
mountpoint twice.
That was completely harmless, but we want to be very explicit about what
FreeBSD VFS APIs are used, because illumos VFS_HOLD and FreeBSD MNT_REF
provide quite different guarantees with respect to the held vfs_t /
mountpoint. On illumos VFS_HOLD is sufficient to guarantee that
vfs_t.vfs_data stays valid. On the other hand, on FreeBSD MNT_REF does
*not* provide the same guarantee about mnt_data. We have to use
vfs_busy() to get that guarantee.
Thus, the calls to VFS_HOLD/VFS_RELE on vnode init and fini are removed.
VFS_HOLD calls are replaced with vfs_busy in the ioctl handlers.
And because vfs_busy has a richer interface that can not be dumbed down
in all cases it's better to explicitly use it rather than trying to mask
it behind VFS_HOLD.
This change fixes a panic that could result from a race between
zfs_umount() and zfs_ioc_rollback(). We observed a case where
zfsvfs_free() tried to destroy data that zfsvfs_teardown() was still
using. That happened because there was nothing to prevent unmounting of
a ZFS filesystem that was in between zfs_suspend_fs() and
zfs_resume_fs().
Reviewed by: kib, smh
MFC after: 3 weeks
Sponsored by: ClusterHQ
Differential Revision: https://reviews.freebsd.org/D2794
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Eli Rosenthal <eli.rosenthal@delphix.com>
illumos/illumos-gate@c20404ff77
6739 userland version of cv_timedwait_hires() always assumes absolute time
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@41c6413cb5
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Author: Alex Wilson <alex.wilson@joyent.com>
illumos/illumos-gate@d09e4475f6
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: Eli Rosenthal <eli.rosenthal@delphix.com>
illumos/illumos-gate@c20404ff77
Reviewed by: Paul Dagnelie <pcd@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Reviewed by: Robert Mustacchi <rm@joyent.com>
Approved by: Robert Mustacchi <rm@joyent.com>
Author: George Wilson <george.wilson@delphix.com>
illumos/illumos-gate@41c6413cb5
Reviewed by: Patrick Mooney <patrick.mooney@joyent.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Dan McDonald <danmcd@omniti.com>
Approved by: Matthew Ahrens <mahrens@delphix.com>
Author: Alex Wilson <alex.wilson@joyent.com>
illumos/illumos-gate@d09e4475f6
- Group the output so that it follows the capability register set more
closely. The first line now contains device information and the
second line contains link information. As a result, ARI status is now
output on the first line, and the link width is moved down to the second
line of link information.
- Only read the DEVICE_CAP2 register to check for ARI if the capability
version is >= 2.
- Don't output any link information if the link capability and status
registers are zero.
- Label the MSI interrupt index value as "MSI" instead of "IRQ".
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
Previously, freebsd32 binaries could submit read/write requests with lengths
greater than INT_MAX that a native kernel would have rejected.
Reviewed by: kib
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D5788
not getting a proper bounds check.
Thanks to CTurt for pointing at this with a big red blinking neon sign.
PR: 206761
Submitted by: sson
Reviewed by: cturt@hardenedbsd.org
MFC after: 3 days
PowerPC has real Open Firmware and does not necessarily need FDT.
Make ofwpci.c only PCI dependent.
Pointed out by: emaste
Reviewed by: nwhitehorn
Obtained from: Semihalf
This is kinda critical to the performance when the CPU is slow and
network bandwidth is high, e.g. in the hypervisor.
Reviewed by: rrs, gallatin, Dexuan Cui <decui microsoft com>
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5765
And factor out tcp_lro_rx_done, which deduplicates the same logic with
netinet/tcp_lro.c
Reviewed by: gallatin (1st version), hps, zbb, np, Dexuan Cui <decui microsoft com>
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5725
The i8254 simulation in Hyper-V is kinda broken and is not available
in Generation 2 Hyper-V VMs, so Hyper-V timer must be registered early
enough so that it can be used to do the TSC freq calibration.
This fixes the notorious warning like this:
calcru: runtime went backwards from 50 usec to 25 usec for pid 0 (kernel)
Submitted by: Dexuan Cui <decui microsoft com>
Reviewed by: kib, sephe
Tested by: kib, sephe
MFC after: 1 week
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5778
case 'g' makes use of value n, which is initialized for case 'b'
and passe through to case 'g'. If case 'g' is called directly
value 'n' is not initialized.
Avoid the issue by initializing n before entering the switch.
CID: 1006375
Reviewed by: bms
The large read test uses an empty file created via mkstemp() rather than
/dev/null as character devices are subject to two different clamping
sysctls. However, I forgot to update some of the error messages after
changing to mkstemp() that were still referring to /dev/null.
