This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
Currently, many drivers support more than one bus of ISA, EISA, MCA,
PCI.
Before this commit, we had, for example, some SCSI devices listed more
than once, iirc, some up to three times (ISA/EISA, MCA, PCI).
Since now the "device" line is common for all of them and they only
differ for the hints stuff, I did the following:
First, list Busses: (E)ISA, MCA, PCI and explain, that only ISA
needs the hints stuff.
Move NIC/SCSI stuff, which were the only split sections, behind these
stuff. Describe all drivers only one time and list all supported
chips.
List all device (+ hints for ISA, if possible).
I've also added few additional supported chips to some drivers, xl for
example and some SCSI drivers.
Also, softupdates is no longer disabled by default, so the comment should
not say, it's not enabled by default due to license issues.
Approved by: asmodai
To come: include PAO devices (imp volunteered for help)
set equal to the number of kilobytes in your cache. The old options are
still supported for backwards compatibility.
Submitted by: Kelly Yancey <kbyanc@posi.net>
accept filters are now loadable as well as able to be compiled into
the kernel.
two accept filters are provided, one that returns sockets when data
arrives the other when an http request is completed (doesn't work
with 0.9 requests)
Reviewed by: jmg
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
Use Warner Losh's "hint" driver to decode ascii strings to fill the
resource table at boot time.
config(8) no longer generates an ioconf.c table - ie: the configuration
no longer has to be compiled into the kernel. You can reconfigure your
isa devices with the likes of this at loader(8) time:
set hint.ed.0.port=0x320
userconfig will be rewritten to use this style interface one day and will
move to /boot/userconfig.4th or something like that.
It is still possible to statically compile in a set of hints into a kernel
if you do not wish to use loader(8). See the "hints" directive in GENERIC
as an example.
All device wiring has been moved out of config(8). There is a set of
helper scripts (see i386/conf/gethints.pl, and the same for alpha and pc98)
that extract the 'at isa? port foo irq bar' from the old files and produces
a hints file. If you install this file as /boot/device.hints (and update
/boot/defaults/loader.conf - You can do a build/install in sys/boot) then
loader will load it automatically for you. You can also compile in the
hints directly with: hints "device.hints" as well.
There are a few things that I'm not too happy with yet. Under this scheme,
things like LINT would no longer be useful as "documentation" of settings.
I have renamed this file to 'NOTES' and stored the example hints strings
in it. However... this is not something that config(8) understands, so
there is a script that extracts the build-specific data from the
documentation file (NOTES) to produce a LINT that can be config'ed and
built. A stack of man4 pages will need updating. :-/
Also, since there is no longer a difference between 'device' and
'pseudo-device' I collapsed the two together, and the resulting 'device'
takes a 'number of units' for devices that still have it statically
allocated. eg: 'device fe 4' will compile the fe driver with NFE set
to 4. You can then set hints for 4 units (0 - 3). Also note that
'device fe0' will be interpreted as "zero units of 'fe'" which would be
bad, so there is a config warning for this. This is only needed for
old drivers that still have static limits on numbers of units.
All the statically limited drivers that I could find were marked.
Please exercise EXTREME CAUTION when transitioning!
Moral support by: phk, msmith, dfr, asmodai, imp, and others
Socket 8 to 370 converters. When (1) CPU_PPRO2CELERON option is
defined, (2) Intel CPU is found and (3) CPU ID is 0x66?, L2 cache is
enabled through MSR 0x11e. The L2 cache latency value can be
specified by CPU_L2_LATENCY option. Default value of L2 cache latency
is 5.
These options are useful if you use Socket 8 to Socket 370 converter
(e.g. Power Leap's PL-Pro/II.) Most PentiumPro BIOSs don't enable L2
cache of Mendocino Celeron CPUs because they don't know Celeron CPUs.
These options are needles if you use a Coppermine (FCPGA) Celeron or
PentiumIII, becuase the L2 cache enable bit is hard wired and L2 cache
is always enabled.
are two supported chips, the NetChip 1080 (only prototypes available)
and the EzLink cable. Any other cable should be supported however as they
are all very much alike (there is a difference between them wrt
performance).
It uses Netgraph.
This driver was mostly written by Doug Ambrisko and Julian Elischer and
I would like to thank Whistle for yet another contribution. And my
aplogies to them for me sitting on the driver for so long (2 months).
Also, many thanks to Reid Augustin from NetChip for providing me with a
prototype of their 1080 chip.
Be aware of the fact that this driver is very immature and has only been
tested very lightly. If someone feels like learning about Netgraph however
this is an excellent driver to start playing with.
This driver should support both the SSI (V.35 etc) E1/T1 unchannelized,
DS3 and HSSI cards. Only tested on the SSI card.
More info at: http://www.lanmedia.com
Thanks to LanMedia for donating two LMC1000P cards.
if_de.c driver modified by: LanMedia
NetGraphification by: Stephen Kiernan <sk-ports@vegamuse.org>
- Add support for using the PCI BIOS functions for configuration space
accesses, and make this the default.
- Make PNPBIOS the default (obsoletes the PNPBIOS config option).
- Add two new boot-time tunables to disable each of the above.
(name, value) pairs to be associated with inodes. This support is
used for ACLs, MAC labels, and Capabilities in the TrustedBSD
security extensions, which are currently under development.
In this implementation, attributes are backed to data vnodes in the
style of the quota support in FFS. Support for FFS extended
attributes may be enabled using the FFS_EXTATTR kernel option
(disabled by default). Userland utilities and man pages will be
committed in the next batch. VFS interfaces and man pages have
been in the repo since 4.0-RELEASE and are unchanged.
o ufs/ufs/extattr.h: UFS-specific extattr defines
o ufs/ufs/ufs_extattr.c: bulk of support routines
o ufs/{ufs,ffs,mfs}/*.[ch]: hooks and extattr.h includes
o contrib/softupdates/ffs_softdep.c: extattr.h includes
o conf/options, conf/files, i386/conf/LINT: added FFS_EXTATTR
o coda/coda_vfsops.c: XXX required extattr.h due to ufsmount.h
(This should not be the case, and will be fixed in a future commit)
Currently attributes are not supported in MFS. This will be fixed.
Reviewed by: adrian, bp, freebsd-fs, other unthanked souls
Obtained from: TrustedBSD Project
From the README:
Any IEEE 802.11 cards use AMD Am79C930 and Harris (Intersil) Chipset
with PCnetMobile firmware by AMD.
BayStack 650 1Mbps Frequency Hopping PCCARD adapter
BayStack 660 2Mbps Direct Sequence PCCARD adapter
Icom SL-200 2Mbps Direct Sequence PCCARD adapter
Melco WLI-PCM 2Mbps Direct Sequence PCCARD adapter
NEL SSMagic 2Mbps Direct Sequence PCCARD adapter
Netwave AirSurfer Plus
1Mbps Frequency Hopping PCCARD adapter
Netwave AirSurfer Pro
2Mbps Direct Sequence PCCARD adapter
Known Problems:
WEP is not supported.
Does not create IBSS itself.
Cannot configure the following on FreeBSD:
selection of infrastructure/adhoc mode
ESSID
...
Submitted by: Atsushi Onoe <onoe@sm.sony.co.jp>
your feet. The conversion of the "snp" device to a dynamically growing
device driver was done just a few days ago by Brooks Davis! Shame on
me for not finding that PR :(
This is a forced commit of tty_snoop.c to give the submitter proper credit,
as most of the patch submitted is actually exactly the same code (by some
large amount of entropy). Brooks also submitted the change to LINT to
set the example of "snp" usage to not include a number, as that number is
now deprecated, so that is also in this commit.
PR: 17629
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
