On single core devices set_stackptrs is only ever called with cpu = 0 in
initarm and will be identical to the existing function. On SMP this needs
to be implemented for sys/arm/mp_machdep.c, but the implementations are
identical for each SoC.
MSI are implemented via Inbound Shared Doorbell 1 interrupts. Interrupts
are triggered by writing to Software Triggered Interrupt registeri (PCIe
card using physical address of this register in BAR0 space). There are 32
interrupts available. It can be increased by using Doorbell 2 and
Doorbell 3 registers to 96 interrupts.
Obtained from: Marvell, Semihalf
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
frequencies. The maximum freqency is 100 kHz according to the datasheet.
- Add child device probing support based on the device tree. It now tries to
find i2c-address property in the tree and attach the device with given slave
address to iicbus.
this array either from Linux boot data, when enabled, or in the
typical way that most ports do it. arm_pyhs_avail_init is coming
soon since it must be a separate function.
is enabled, sets values based on the metadata passed in. Otherwise
fake_preload_metadata is called. Change the default parse_boot_param
to default_parse_boot_param. Enable this functionality only on the mv
platform, which is where most of the code is from.
Reviewed by: cognet, Ian Lapore
the boot parameters from initarm first thing. parse_boot_param parses
the boot arguments and converts them to the /boot/loader metadata the
rest of the kernel uses. parse_boot_param is a weak alias to
fake_preload_metadata, which all the platforms use now, but may become
more extensive in the future.
Since it is a weak symbol, specific boards may define their own
parse_boot_param to interface to custom boot loaders.
Reviewed by: cognet@, Ian Lapore
structure with the first 4 registers to allow a wider range of boot
loaders to work. Future commits will make use of this to centralize
support for the different loaders.
According to the open firmware standard, finddevice call has to return
a phandle with value of -1 in case of error.
This commit is to:
- Fix the FDT implementation of this interface (ofw_fdt_finddevice) to
return (phandle_t)-1 in case of error, instead of 0 as it does now.
- Fix up the callers of OF_finddevice() to compare the return value with
-1 instead of 0 to check for errors.
- Since phandle_t is unsigned, the return value of OF_finddevice should
be checked with '== -1' rather than '<= 0' or '> 0', fix up these cases
as well.
Reported by: nwhitehorn
Reviewed by: raj
Approved by: raj, nwhitehorn
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
The compiler will truncate the 32-bit return value of mv_gpio_value_get()
to match the 8-bit return value of mv_gpio_in(). A conditional expression
is used to have mv_gpio_in() always return 0 or 1 instead.
a hard hang due to an interrupt storm or stuck interrupt pin. We
return the next IRQ that is larger than the last one returned and
in doing so give all interrupts a fair chance of being handled.
Consequently, we're able to break into the kernel debugger in such
an event.
masked-off by the firmware.
o In DELAY(). Make sure we have an inner-loop body that the compiler
cannot eliminate. While timing does not have to be perfect, the
loops must be there to have at least some notion of delay.
Obtained from: Juniper Networks
pins to determine whether there's a high register set or not. This
allows platform_gpio_init() to work without duplicating the work
done in the attach method.
get properties from the parent. The parent is in fact the FDT bus
itself and will therefore not have the properties we're looking
for.
Sponsored by: Juniper Networks
defined. The kernel linker doesn't deal with symbols of
type NOTYPE and typically gives the wrong symbol ($a) for
local symbols.
Obtained from: Juniper Networks, Inc.
- Implement proper combined mode decoding for Intel controllers to properly
identify SATA and PATA channels and associate ATA channels with SATA ports.
This fixes wrong reporting and in some cases hard resets to wrong SATA ports.
- Improve SATA registers support to handle hot-plug events and potentially
interface errors. For ICH5/6300ESB chipsets these registers accessible via
PCI config space. For later ones they may be accessible via PCI BAR(5).
- For controllers not generating interrupts on hot-plug events, implement
periodic status polling. Use it to detect hot-plug on Intel and VIA
controllers. Same probably could also be used for Serverworks and SIS.
