incomplete, but will eventually allow the same drivers to function
with both oldcard and newcard.
o Remove include of opt_bus.h. It isn't needed and gets in the way of
module building.
through, establish what our LUN width is. Unfortunately, we can't ask
the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs
(SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't
load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We
have to assume only one LUN for Fibre Channel because the LUN setting
in Request Queue entries is in different places whether we have SCCLUN
firmware or not, so the only LUN guaranteed to work for both is LUN 0.
Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used-
instead use run time determinants based upon isp->isp_maxluns.
After starting firmware, delay 500us to give it a chance to get rolling.
Fix the interrupt service routine to check for both isr && sema being zero
before thinking this was a spurious interrupt. Following the manuals,
allow for both Mailbox as well as Queue Reponse type interrupts for regular
SCSI.
(we always support fabric now). Remove SCCLUN definition (we always
support SCCLUN now, if we load the f/w). Add typedef definition of an
external firmware fetch function.
a full reindex in this case to remove the old record. #ifdef -u capability
since this is available on FreeBSD only.
PR: bin/16418
Problem pointed out by: Masachika ISHIZUKA <ishizuka@ish.org>
fields, not lex/yacc grammar so it is not an exact match but should be
close enough for most cases.
Deal with 'port?', 'irq?' style specifications. These are parsed as
seperate values in lex/yacc in config(8) but tripped up this helper tool.
deal with filename arguments. It is amazing how much you forget over time.
Thanks to the people that reminded me this. I knew there was an easy way
that didn't involve messing with $argv, filehandles, etc, but just could
not remember - all of my books are on the opposite side of the planet..
world as was our old way, rather than when building a kernel.
Some people do not like the new way, and the release building still assumes
modules are built with the world.
theory, this should allow the K7V Athlon motherboard to boot ok with boot
virus protection enabled. However, I have no hardware to test this. It
shouldn't break anything though. :)
Prodded by: Kelly Yancey <kbyanc@posi.net>
renamed to {s|g}etflagsbyname, which received objections. They're
now called strtofflags (string to file flags) and fflagstostr (file
flags to string).
Suggested by: bde
address on an interface. This basically allows you to do what my
little setmac module/utility does via ifconfig. This involves the
following changes:
socket.h: define SIOCSIFLLADDR
if.c: add support for SIOCSIFLLADDR, which resets the values in
the arpcom struct and sockaddr_dl for the specified interface.
Note that if the interface is already up, we need to down/up
it in order to program the underlying hardware's receive filter.
ifconfig.c: add lladdr command
ifconfig.8: document lladdr command
You can now force the MAC address on any ethernet interface to be
whatever you want. (The change is not sticky across reboots of course:
we don't actually reprogram the EEPROM or anything.) Actually, you
can reprogram the MAC address on other kinds of interfaces too; this
shouldn't be ethernet-specific (though at the moment it's limited to
6 bytes of address data).
Nobody ran up to me and said "this is the politically correct way to
do this!" so I don't want to hear any complaints from people who think
I could have done it more elegantly. Consider yourselves lucky I didn't
do it by having ifconfig tread all over /dev/kmem.
of perl man pages and site_perl directories for alpha and i386 in /usr/local,
and share/aclocal and share/doc/ja in /usr/local and /usr/X11R6.
Reviewed by: the ports list
Approved by: steve (alpha part)
