the username-for-accounting field (P), not the username-for-headerpage (L).
These are usually the same value, except that control files do not have
the username-for-headerpage field if the user has requested no header page.
- Also rename the cji_username field to cji_headruser, to make it clear that
the value should only be used for the header page. (aka banner page)
MFC after: 3 weeks
not believe that these leaks had a practical impact,
since the situations in which they would have occurred
would have been extremely rare.
MFC after: 2 weeks
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
prefixes (Ki, Mi, Gi...) for humanize_number(3).
Note that applications has to pass HN_IEC_PREFIXES to use this
feature for backward compatibility reasons.
Reviewed by: arundel
MFC after: 2 weeks
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
embedded flash stores.
Some devices - notably those with uboot - don't have an
explicit partition table (eg like Redboot's FIS.)
geom_map thus provides an easy way to export the hard-coded
flash layout as geom providers for use by filesystems and
other tools.
It also includes a "search" function which allows for
dynamic creation of partition layouts where the device only
has a single hard-coded partition. For example, if
there is a "kernel+rootfs" partition, a single image can
be created which appends the rootfs after the kernel with
an appropriate search string. geom_map can be told to
search for said search string and create a partition
beginning after it.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
this happens just before the build is started (within the same second)
CHECK_TIME actually triggers thinking param.h is in the future (see f_Xtime,
c_Xtime logi in find(1) sources for the details in !F_EXACTTIME case).
Using the -mtime -0s (seconds, rather than no unit) avoids this 1s race.
Submitted by: ed (2009-05-03)
Reviewed by: cperciva (2009-05-03), emaste
Tested by: bz (for almost two years)
MFC after: 4 days
of NFSv2 getting an error return from VOP_MKNOD(). Without this
patch, the server file system remains busy after an NFSv2
VOP_MKNOD() fails.
MFC after: 2 weeks
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
for a new journal specific partial truncate routine.
- Use dep_current[] in place of specific dependency counts. This is
automatically maintained when workitems are allocated and has
less risk of becoming incorrect.
the experimental NFS server, so that it doesn't leak memory
when unloaded. However, unloading the NFSv4 server is not
recommended, since all NFSv4 state will be lost by the unload
and clients will have to recover the state after a server
reload/restart as if the server crashed/rebooted.
MFC after: 2 weeks
negative return value from write to update its position in
a buffer. The patch, courtesy of Andrey Simonenko, also simplifies
a conditional by removing the "i != cnt" clause, since it is
always true at this point in the code. The bug caused problems
for mountd, when it generated a large reply to an exports RPC
request.
Submitted by: simon at comsys.ntu-kpi.kiev.ua
MFC after: 2 weeks
