Put @includes in a better spot. Fix many cases of 2 space indents and spaces
between a function name and the parens. Use KASSERT instead of a home-rolled
ASSERT. Remove some undeeded caddr casts.
- Define option FORCECONSPEED to force the serial console to
be CONSPEED. I've run into a lot of boards in which
the detect for prior speed doesn't work and ends up with
broken console since it is at the wrong speed.
- If a serial port is marked as a console, but console=vidconsole
and if the serial ports doesn't exist it will be probed and
attached at a 8250 chip. Then writes to that will freeze the
system.
- Add an option flags 0x400000 to mark this as a potential
comconsole in-case the one flaged with 0x10 does not exist
in the system.
This makes it easier to deploy on systems with one or two serial ports.
Obtained from: IronPort
- Use the dh_inserted member of the dispatch header in the Windows
timer structure to indicate that the timer has been "inserted into
the timer queue" (i.e. armed via timeout()). Use this as the value
to return to the caller in KeCancelTimer(). Previously, I was using
callout_pending(), but you can't use that with timeout()/untimeout()
without creating a potential race condition.
- Make ntoskrnl_init_timer() just a wrapper around ntoskrnl_init_timer_ex()
(reduces some code duplication).
- Drop Giant when entering if_ndis.c:ndis_tick() and
subr_ntorkrnl.c:ntoskrnl_timercall(). At the moment, I'm forced to
use system callwheel via timeout()/untimeout() to handle timers rather
than the callout API (struct callout is too big to fit inside the
Windows struct KTIMER, so I'm kind of hosed). Unfortunately, all
the callouts in the callwhere are not marked as MPSAFE, so when
one of them fires, it implicitly acquires Giant before invoking the
callback routine (and releases it when it returns). I don't need to
hold Giant, but there's no way to stop the callout code from acquiring
it as long as I'm using timeout()/untimeout(), so for now we cheat
by just dropping Giant right away (and re-acquiring it right before
the routine returns so keep the callout code happy). At some point,
I will need to solve this better, but for now this should be a suitable
workaround.
channels. This also work when PCI native mode has been selected
(patch for /sys/dev/pci/pci.c needed for that) since pci_get_progif
uses the saved value for progif, not the one stored after we may have
changed from legacy mode to native PCI mode.
1) In pci.c, we need to check the child device's state, not the parent
device's state.
2) In acpi_pci.c, we have to run the power state change after the acpi
method when the old_state is > new state, not the other way around.
Submitted by: Dmitry Remesov
PR: 65694
caller to vm_page_grab(). Although this gives VM_ALLOC_ZERO a
different meaning for vm_page_grab() than for vm_page_alloc(), I feel
such change is necessary to accomplish other goals. Specifically, I
want to make the PG_ZERO flag immutable between the time it is
allocated by vm_page_alloc() and freed by vm_page_free() or
vm_page_free_zero() to avoid locking overheads. Once we gave up on
the ability to automatically recognize a zeroed page upon entry to
vm_page_free(), the ability to mutate the PG_ZERO flag became useless.
Instead, I would like to say that "Once a page becomes valid, its
PG_ZERO flag must be ignored."
added an arbitrary delay to our readings, causing us to use the ACPI-safe
read method when not necessary. Submitted by: bde
Old:
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks BAD min = 3, max = 19, width = 16
ACPI timer looks GOOD min = 3, max = 5, width = 2
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-safe" frequency 3579545 Hz quality 1000
New:
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
Also, reduce unnecesary overhead in ACPI-fast by remove the barrier for
reads. The timer in the ACPI-fast case is known to increase monotonically
so there is no need to serialize access to it.
modules is a very nice way to produce hard-to-find panics. Who would look for
a bug in a Makefile anyway?
Has anyone seen the pointy hat? :-o
Approved by: njl (mentor)
resource pre-allocation. The problem is that the BARs of the EBus bridges
contain the ranges for the resources for the EBus devices beyond the bridge.
So when the EBus code tries to allocate the resource for an EBus device
it's already allocated by the PCI code.
To be removed again as soon as we have a proper solution in the EBus Code.
Reviewed by: tmm
Approved by: marcel (mentor)
secondary bus is 0, we program the primary bus, the secondary bus and
the suborindate bus. This isn't ideal, since we start at parent_bus +
1 and store this in a static.
Ideally, we'd walk the tree and assign bus numbers. However, that's
harder to accomplish without some help from the bus layer which we're
not planning on doing that until 6.
This fixes my CardBus problems on my Sony PCG-Z1WA, and might fix the
Dells that have had problems.
gadgets (hotkeys, lcd, ...) on Asus laptops. I aim to closely track the
acpi4asus project which implements these features in the Linux kernel.
If this breaks your laptop, please let me know how it does it :-)
Approved by: njl (mentor)
(I hope.)
My original instinct to make ndis_return_packet() asynchronous was correct.
Making ndis_rxeof() submit packets to the stack asynchronously fixes
one recursive spinlock acquisition, but it's also possible for it to
happen via the ndis_txeof() path too. So:
- In if_ndis.c, revert ndis_rxeof() to its old behavior (and don't bother
putting ndis_rxeof_serial() back since we don't need it anymore).
- In kern_ndis.c, make ndis_return_packet() submit the call to the
MiniportReturnPacket() function to the "ndis swi" thread so that
it always happens in another context no matter who calls it.
workaround was for hardware where the clock was not latched, not for
hardware that was too slow. Also, make variable names more specific for ddb
printing.
While I would have prefered to have a solution that didn't move
knowledge of this into the pci layer. However, this is literally the
only exception that's listed in the PCI standard to the usual way of
decoding BARs. atapci devices in legacy mode now ignore the first 4
bars and hard code the values to the legacy ide values (well, for each
of the controllers that are in legacy mode). The 5th bar is handled
normally.
Remove the zero bar handling. zero bars should be ignored at all
other times, and since we handle that specially, we don't need the
older workaround.
what the ACPI-safe workaround is intended to fix. Requested by phk.
Set the bushandle and tag when attaching the timer, don't do it each time
in read_counter(). Pointed out by bde.
Move test_counter() to the end. Staticize acpi_timer_reg.
of you with other cards, please do review and test the drivers for
MP-safety and disable Giant in the interrupt routines when you are
sure of proper functionality.
wireless ever since I added the new spinlock code. Previously, I added
a special ndis_rxeof_serial() function to insure that when we receive
a packet, we never end up calling the MiniportReturnPacket() routine
until after the receive handler has finished. I set things up so that
ndis_rxeof_serial() would only be used for serialized miniports since
they depend on this property. Well, it turns out deserialized miniports
depend on a similar property: you can't let MiniportReturnPacket() be
called from the same context as the receive handler at all. The 2100B
driver happens to use a single spinlock for all of its synchronization,
and it tries to acquire it both while in MiniportHandleInterrupt() and
in MiniportReturnPacket(), so if we call MiniportReturnPacket() from
the MiniportHandleInterrupt() context, we will end up trying to acquire
the spinlock recursively, which you can't do.
To fix this, I made the ndis_rxeof_serial() handler the default. An
alternate solution would be to make ndis_return_packet() submit
the call to MiniportReturnPacket() to the NDIS task queue thread.
I may do that in the future, after I've tested things a bit more.
supported. Symptoms of this bug included unnecessary use of ACPI-safe
and a dmesg that has deltas of about 2^24:
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 16777206, width = 16777204
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 2, max = 16777210, width = 16777208
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
ACPI timer looks GOOD min = 4, max = 5, width = 1
ACPI timer looks BAD min = 2, max = 7, width = 5
ACPI timer looks BAD min = 4, max = 16777189, width = 16777185
To fix this:
* Use a 32 bit timecounter mask when the timer is 32 bits.
* In test_counter(), use the acpi_TimerDelta function which handles 24/32
bit timers and wraparound.
Miscellaneous fixes:
* Use C99 initializers for timecounter struct.
* Use u_int and uint32_t where appropriate instead of unsigned.
* Remove whitespace-only lines
* Remove the old PIIX4 PCI workaround. The timecounter testing code has
been in use for long enough to prove it's functional.
globally available. acpi_TimerDelta() subtracts two readings from the
ACPI PM timer and returns the difference. It properly distinguishes between
24-bit and 32-bit timers and handles wraparound.
a NULL crsbuf pointer. This shouldn't happen if it returns AE_OK. We'll
figure out why this is happening later.
Submitted by: Bruno Ducrot <ducrot@poupinou.org>
routine since the error will be reported back to the user buffer.
This will quiet down the bootverbose case when using an ACU which
does brute force discovery of the physical and logical devices.
of the struct, so that a placeholder for it (or unportable C99
initializers) are not needed for entries that don't use it. Use a C99
initializer for the 1 entry that uses it. Removed 91 placeholders.
This also restores API compatibility with NetBSD and RELENG_4 for most
entries.
Removed the requirement for a particular subvendor/subproduct in
rev.1.26 (VScom PCI-800L card). While the BARs, etc., may depend on
the sub-ids, this is not known to be so, and I think it is better to
guess that they don't. The decision to check sub-id checks in this
file is apparently random; for VScom cards they were checked in 3 of
8 cases.
Reviewed by: timeout by committer (joerg) after 6 months
Nehemiah chip, but the work is all done in hardware.
There are three opportunities to add other entropy; the Data
Buffer, the Cipher's IV and the Cipher's key. A future commit
will exploit these opportunities.
Logical volumes on these devices show up as LUNs behind another
controller (also known as proxy controller). In order to issue
firmware commands for a volume on a proxy controller, they must be
targeted at the address of the proxy controller it is attached to,
not the Host/PCI controller.
A proxy controller is defined as a device listed in the INQUIRY
PHYSICAL LUNS command who's L2 and L3 SCSI addresses are zero. The
corresponding address returned defines which "bus" the controller
lives on and we use this to create a virtual CAM bus.
A logical volume's addresses first byte defines the logical drive
number. The second byte defines the bus that it is attached to
which corresponds to the BUS of the proxy controller's found or the
Host/PCI controller.
Change event notification to be handled in its own kernel thread.
This is needed since some events may require the driver to sleep
on some operations and this cannot be done during interrupt context.
With this change, it is now possible to create and destroy logical
volumes from FreeBSD, but it requires a native application to
construct the proper firmware commands which is not publicly
available.
Special thanks to John Cagle @ HP for providing remote access to
all the hardware and beating on the storage engineers at HP to
answer my questions.
uiomove(9) is not properly locked. So, return to NEEDGIANT
mode. Later, when uiomove is finely locked, I'll revisit.
While I'm here, provide some temporary debugging output to
help catch blocking startups.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
because they bogusly check for defined(INTR_MPSAFE) -- something which
never was a #define. Correct the definitions.
This make INTR_TYPE_AV finally get used instead of the lower-priority
INTR_TYPE_TTY, so it's quite possible some improvement will be had
on sound driver performance. It would also make all the drivers
marked INTR_MPSAFE actually run without Giant (which does seem to
work for me), but:
INTR_MPSAFE HAS BEEN REMOVED FROM EVERY SOUND DRIVER!
It needs to be re-added on a case-by-case basis since there is no one
who will vouch for which sound drivers, if any, willy actually operate
correctly without Giant, since there hasn't been testing because of
this bug disabling INTR_MPSAFE.
Found by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
attempting to duplicate Windows spinlocks. Windows spinlocks differ
from FreeBSD spinlocks in the way they block preemption. FreeBSD
spinlocks use critical_enter(), which masks off _all_ interrupts.
This prevents any other threads from being scheduled, but it also
prevents ISRs from running. In Windows, preemption is achieved by
raising the processor IRQL to DISPATCH_LEVEL, which prevents other
threads from preempting you, but does _not_ prevent device ISRs
from running. (This is essentially what Solaris calls dispatcher
locks.) The Windows spinlock itself (kspin_lock) is just an integer
value which is atomically set when you acquire the lock and atomically
cleared when you release it.
FreeBSD doesn't have IRQ levels, so we have to cheat a little by
using thread priorities: normal thread priority is PASSIVE_LEVEL,
lowest interrupt thread priority is DISPATCH_LEVEL, highest thread
priority is DEVICE_LEVEL (PI_REALTIME) and critical_enter() is
HIGH_LEVEL. In practice, only PASSIVE_LEVEL and DISPATCH_LEVEL
matter to us. The immediate benefit of all this is that I no
longer have to rely on a mutex pool.
Now, I'm sure many people will be seized by the urge to criticize
me for doing an end run around our own spinlock implementation, but
it makes more sense to do it this way. Well, it does to me anyway.
Overview of the changes:
- Properly implement hal_lock(), hal_unlock(), hal_irql(),
hal_raise_irql() and hal_lower_irql() so that they more closely
resemble their Windows counterparts. The IRQL is determined by
thread priority.
- Make ntoskrnl_lock_dpc() and ntoskrnl_unlock_dpc() do what they do
in Windows, which is to atomically set/clear the lock value. These
routines are designed to be called from DISPATCH_LEVEL, and are
actually half of the work involved in acquiring/releasing spinlocks.
- Add FASTCALL1(), FASTCALL2() and FASTCALL3() macros/wrappers
that allow us to call a _fastcall function in spite of the fact
that our version of gcc doesn't support __attribute__((__fastcall__))
yet. The macros take 1, 2 or 3 arguments, respectively. We need
to call hal_lock(), hal_unlock() etc... ourselves, but can't really
invoke the function directly. I could have just made the underlying
functions native routines and put _fastcall wrappers around them for
the benefit of Windows binaries, but that would create needless bloat.
- Remove ndis_mtxpool and all references to it. We don't need it
anymore.
- Re-implement the NdisSpinLock routines so that they use hal_lock()
and friends like they do in Windows.
- Use the new spinlock methods for handling lookaside lists and
linked list updates in place of the mutex locks that were there
before.
- Remove mutex locking from ndis_isr() and ndis_intrhand() since they're
already called with ndis_intrmtx held in if_ndis.c.
- Put ndis_destroy_lock() code under explicit #ifdef notdef/#endif.
It turns out there are some drivers which stupidly free the memory
in which their spinlocks reside before calling ndis_destroy_lock()
on them (touch-after-free bug). The ADMtek wireless driver
is guilty of this faux pas. (Why this doesn't clobber Windows I
have no idea.)
- Make NdisDprAcquireSpinLock() and NdisDprReleaseSpinLock() into
real functions instead of aliasing them to NdisAcaquireSpinLock()
and NdisReleaseSpinLock(). The Dpr routines use
KeAcquireSpinLockAtDpcLevel() level and KeReleaseSpinLockFromDpcLevel(),
which acquires the lock without twiddling the IRQL.
- In ndis_linksts_done(), do _not_ call ndis_80211_getstate(). Some
drivers may call the status/status done callbacks as the result of
setting an OID: ndis_80211_getstate() gets OIDs, which means we
might cause the driver to recursively access some of its internal
structures unexpectedly. The ndis_ticktask() routine will call
ndis_80211_getstate() for us eventually anyway.
- Fix the channel setting code a little in ndis_80211_setstate(),
and initialize the channel to IEEE80211_CHAN_ANYC. (The Microsoft
spec says you're not supposed to twiddle the channel in BSS mode;
I may need to enforce this later.) This fixes the problems I was
having with the ADMtek adm8211 driver: we were setting the channel
to a non-standard default, which would cause it to fail to associate
in BSS mode.
- Use hal_raise_irql() to raise our IRQL to DISPATCH_LEVEL when
calling certain miniport routines, per the Microsoft documentation.
I think that's everything. Hopefully, other than fixing the ADMtek
driver, there should be no apparent change in behavior.
change the video output but use a separate device with a DSSX method
and a HID of "TOS6201" instead. We use a pseudo-driver to get the handle
for this object and pass it to the acpi_toshiba driver.
This is untested but seems to match the Linux Toshiba driver.
the sense that any write to them reads back as a 0. This presents a
problem to our resource allocation scheme. If we encounter such vars,
the code now treats them as special, allowing any allocation against
them to succeed. I've not seen anything in the standard to clearify
what host software should do when it encounters these sorts of BARs.
Also cleaned up some output while I'm here and add commmented out
bootverbose lines until I'm ready to reduce the verbosity of boot
messages.
This gets a number of south bridges and ata controllers made mostly by
VIA, AMD and nVidia working again. Thanks to Soren Schmidt for his
help in coming up with this patch.
controllers (PDC203** PDC206**).
This also adds preliminary support for the Promise SX4/SX4000 but *only*
as a "normal" Promise ATA controller (ATA RAID's are supported though
but only RAID0, RAID1 and RAID0+1).
This cuts off yet another 5-8% of the command overhead on promise controllers,
making them the fastest we have ever had support for.
Work is now continuing to add support for this in ATA RAID, to accellerate
ATA RAID quite a bit on these controllers, and especially the SX4/SX4000
series as they have quite a few tricks in there..
This commit also adds a few fixes to the SATA code needed for proper support.
Alignment for pccards should also be treated in a similar way that
we tread it for cardbus cards.
Remove bogus debugs while I'm here.
# This is also necessary to make the CIS reading work.
Submitted by: Carlos Velasco
(1) Align to 64k for the CIS. Some cards don't like it when we aren't
aligned to a 64k boundary. I can't find anything in the standard
that requires this, but I have 1/2 dozen cards that won't work at
all unless I enable this.
(2) Sleep 1s before scanning the CIS. This may be a nop, but has little
harm.
(3) The CIS can be up to 4k in some weird, odd-ball edge cases. Since we
have limiters for when that's not the case, it does no harm to increase
it to 4k.
#1 was submitted, in a different form, by Carlos Velasco.
we get the resource allocation stuff hammered out.
Fix and off by one error that caused unnecessary filtering of valid
BARs for only 4 bytes than ICH3 and other PCI IDE controllers have.
Andrew Gallatin submitted this, although it doesn't solve the problems
ICH3 controllers have with the new code, it does restore the former
resource list on the probe line.
device in D0 to D0, that's a no-op, however the messages seem to be
confusing some people. Eventually, these messages will be parked
behind a if (bootverbose).
# I don't think this will fix any real bugs...
Xircom had an unfortunate habit of re-using PCMCIA IDs for quite different
cards - the xe driver knows about this and uses the first byte of 'extra'
PCMCIA ID info to identify cards with ambiguous IDs.
Reviewed by: imp (mentor)
can more easily be used INSTEAD OF the hard-working Yarrow.
The only hardware source used at this point is the one inside
the VIA C3 Nehemiah (Stepping 3 and above) CPU. More sources will
be added in due course. Contributions welcome!
o Save and restore bars for suspend/resume as well as for D3->D0
transitions.
o preallocate resources that the PCI devices use to avoid resource
conflicts
o lazy allocation of resources not allocated by the BIOS.
o set unattached drivers to state D3. Set power state to D0
before probe/attach. Right now there's two special cases
for this (display and memory devices) that need work in other
areas of the tree.
Please report any bugs to me.
Reference objects changed from ACPI_TYPE_ANY to ACPI_TYPE_LOCAL_REFERENCE
in Oct. 2002, this may help systems where switching the cooler on failed.
We support both types for now until this sorts out.
some machines to enable wake events for more devices although I haven't
seen a system yet that uses this form. Also, introduce acpi_GetReference()
which retrieves an object reference from various types.
are enumerated in the ACPI device tree. In addition to the normal PCI
powerstate functionality, the ACPI _PSx methods are executed and ACPI
PowerResources are switched on and off via the acpi_pwr_switch_consumer()
function.
Glanced at by: imp, njl
case we should wait for the resetdone handler to be called before
returning.
- When providing resources via ndis_query_resources(), uses the
computed rsclen when using bcopy() to copy out the resource data
rather than the caller-supplied buffer length.
- Avoid using ndis_reset_nic() in if_ndis.c unless we really need
to reset the NIC because of a problem.
- Allow interrupts to be fielded during ndis_attach(), at least
as far as allowing ndis_isr() and ndis_intrhand() to run.
- Use ndis_80211_rates_ex when probing for supported rates. Technically,
this isn't supposed to work since, although Microsoft added the extended
rate structure with the NDIS 5.1 update, the spec still says that
the OID_802_11_SUPPORTED_RATES OID uses ndis_80211_rates. In spite of
this, it appears some drivers use it anyway.
- When adding in our guessed rates, check to see if they already exist
so that we avoid any duplicates.
- Add a printf() to ndis_open_file() that alerts the user when a
driver attempts to open a file under /compat/ndis.
With these changes, I can get the driver for the SMC 2802W 54g PCI
card to load and run. This board uses a Prism54G chip. Note that in
order for this driver to work, you must place the supplied smc2802w.arm
firmware image under /compat/ndis. (The firmware is not resident on
the device.)
Note that this should also allow the 3Com 3CRWE154G72 card to work
as well; as far as I can tell, these cards also use a Prism54G chip.
without the (defunct) isa compatibility shims. The new-bus-specific
parts are very similar to the ones for the pci probe and attach.
This was held up too long waiting for a repo copy to src/sys/dev/cy,
so I decided to fix the files in their old place. This gives easier
to read and merge diffs anyway.
The "count" line in src/sys/conf/files won't be changed until after
the repo copy, so old kernel configs that specify a count need not be
(and must not be) changed until then. The count is just ignored in
the driver. One unfinished detail is dynamic allocation of arrays
with <count> and (<count> * 32) entries, and iteration over the arrays.
This is now kludged with a fixed count of 10 (up to 10 cards with up
to 32 ports each).
Prodded by: imp
Submitted by: mostly by imp
Approved by: imp
common attach function so that the lock gets initialized in all cases.
This fixes breakage of the initialization of the lock in the pci case
in rev.1.135 (between the releases of 5.1 and 5.2). The lock is only
used in the SMP case, so this bug was not always fatal.
and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
scenario into #ifdef DEBUG. This makes my cluster with Belkin
KVM switch completely usable, even if the KVM switch and mouse
get a bit confused sometimes.
Without this, when the mouse gets confused, all sorts of crud
gets spammed all over the screen. With this, the mouse may appear
dead for a second or three, but it recovers silently.
phandle_t. Since both are typedefed to unsigned int, this is more
or less cosmetic.
- Fix the code that determines whether a creator instance was used
for firmware output (and should not be blanked on initialization).
Since r1.2 of dev/fb/creator.c, this consisted comparing a handle of
an instance of a package with a handle of the package itself.
Use the test from r1.1, which utilizes OF_instance_to_package().
Submitted by: Marius Strobl <marius@alchemy.franken.de>
"... uart_cpu_sparc64.c currently only looks at /options if ttyX is
the selected console. However, there's one case where it should
additionally look at /chosen. If "keyboard" is the selected input-
device and "screen" the output-device (both via /options) but the
keyboard is unplugged, OF automatically switches to ttya for the
console. It even prints a line telling so on "screen". Solaris
respects this behaviour and uses ttya as the console in this case
and people probably expect FreeBSD to do the same (it's also very
handy to temporarily switch consoles)..."
Submitted by: Marius Strobl <marius@alchemy.franken.de>
Has no doubt the change is correct: marcel
of UARTs. We already did this in uart_cpu_getdev().
While here, also check the compat name for "su" or "su16550".
Both changes submitted by: Marius Strobl <marius@alchemy.franken.de>
Does not doubt the correctness of the second change: marcel
Add in missing case for i845G in the attach routine. I'll MFC this
with the rest of the change after the 4.10 codefreeze lifts.
Reviewed By: Doug Rabson
on architectures that need to call cninit() before the machine is
ready to support mutexes (required by make_dev()).
- Remove make_dev() call from scinit() when flags indicate
unit is the system console, rely on sc_attach_unit() to
handle it.
- When trying to access current screen's status (scr_stat
structure) use the static one provided for the initial
system console if no dev_t is available.
- When calling make_dev() in sc_attach_unit() catch special
case of system's initial console and set up dev_t structure
to include pointer to console's scr_stat struct.
Reviewed by: marcel
Tested by: marcel, grehan (ppc), others on current@
Approved by: rwatson (mentor)
completely understand], md_takeroot() runs before md_preloaded(),
rendering both useless.
As a fix, move the body (effectively one line!) of md_takeroot()
into md_preloaded(), and get rid of the stuff that has become useless.
Bug and fix reported 10 days ago on -current, no reply.
they all do and handle that without alarming the user. Also pull in a bit
of defensive code from OpenBSD that triggers when a card is recognised but
not properly classified as either Genesis or Yukon. Not that I could ever
have needed this. :-)
Obtained from: OpenBSD/NetBSD (partially)
MFC after: 2 weeks
read-only. Need to enable "legacy support", by poking
into pci config space. (comment from the patch)
Submited by: Autrijus Tang <autrijus@autrijus.org>
Approved by: tanimura (mentor)
is necessary because some IBMs use recursive methods (pointed out by
Robert Moore from Intel). The latter was a typo on my part. It was disabled
by default when it should have been enabled.
resource_var.h.
In kern_ndis.c:ndis_convert_res(), fill in the cprd_flags and
cprd_sharedisp fields as best we can.
In if_ndis.c:ndis_setmulti(), don't bother updating the multicast
filter if our multicast address list is empty.
Add some missing updates to ndis_var.h and ntoskrnl_var.h that I
forgot to check in when I added the KeDpc stuff.
* all
- s/__FUNCTION__/__func__/.
Submitted by: Stefan Farfeleder <stefan@fafoe.narf.at>
- Compatibility for RELENG_4 and DragonFly.
* firewire
- Timestamp just before queuing.
- Retry bus probe if it fails.
- Use device_printf() for debug message.
- Invalidiate CROM while update.
- Don't process minimum/invalid CROM.
* sbp
- Add ORB_SHORTAGE flag.
- Add sbp.tags tunable.
- Revive doorbell support. It's not enabled by default.
variable length, so we should not be trying to copy it into a fixed
length buffer, especially one on the stack. malloc() a buffer of the
right size and return a pointer to that instead.
Fixes a crash I discovered when testing whe a Cisco AP in infrastructure
mode, which returns several information elements that make the
ndis_wlan_bssid_ex structure larger than expected.
Because xfer->send.payload is a pointer to the buffer, '&' shouldn't be there.
Submitted by: John Weisgerber <weisgerberj@gsilumonics.com>
PR: misc/64623
(1 << 24) - 2 instead of 1 << 24, which it was obviously intended to
be). This fixes SBus isp(4)s on sparc64 machines.
Report and testing: Marius Strobl <marius@alchemy.franken.de>
(NIC would claim to establish a link with an ad-hoc net but it couldn't
send/receive packets). It turns out that every time the checkforhang
handler was called by ndis_ticktask(), the driver would generate a new
media connect event. The NDIS spec says the checkforhang handler is
called "approximately every 2 seconds" but using exactly 2 seconds seems
too fast. Using 3 seconds makes it happy again, so we'll go with that
for now.
instead of bus_alloc_resource_any() to restore source compatibility
with 5.2-REL and 5.2.1-REL systems. bus_alloc_resource_any() doesn't
really do anything besides hide some of bus_alloc_resource()'s arguments
from us, and in my opinion this isn't worth breaking backwards
compatibility for people who want to use the NDISulator code on 5.2.x.
are actually layered on top of the KeTimer API in subr_ntoskrnl.c, just
as it is in Windows. This reduces code duplication and more closely
imitates the way things are done in Windows.
- Modify ndis_encode_parm() to deal with the case where we have
a registry key expressed as a hex value ("0x1") which is being
read via NdisReadConfiguration() as an int. Previously, we tried
to decode things like "0x1" with strtol() using a base of 10, which
would always yield 0. This is what was causing problems with the
Intel 2200BG Centrino 802.11g driver: the .inf file that comes
with it has a key called RadioEnable with a value of 0x1. We
incorrectly decoded this value to '0' when it was queried, hence
the driver thought we wanted the radio turned off.
- In if_ndis.c, most drivers don't accept NDIS_80211_AUTHMODE_AUTO,
but NDIS_80211_AUTHMODE_SHARED may not be right in some cases,
so for now always use NDIS_80211_AUTHMODE_OPEN.
NOTE: There is still one problem with the Intel 2200BG driver: it
happens that the kernel stack in Windows is larger than the kernel
stack in FreeBSD. The 2200BG driver sometimes eats up more than 2
pages of stack space, which can lead to a double fault panic.
For the moment, I got things to work by adding the following to
my kernel config file:
options KSTACK_PAGES=8
I'm pretty sure 8 is too big; I just picked this value out of a hat
as a test, and it happened to work, so I left it. 4 pages might be
enough. Unfortunately, I don't think you can dynamically give a
thread a larger stack, so I'm not sure how to handle this short of
putting a note in the man page about it and dealing with the flood
of mail from people who never read man pages.
only done minimal testing on one of these cards and the firmware folks
have been extremely uncooperative in answering my qeustions about them, so
hopefully they will work ok for everyone.
This completes the effort to handle dependent functions, which are used
in some machines for irq link resources. Also, clean up some nearby
comments while I'm at it.
This change has not been tested.
This change was triggered by a gcc(1) warning on ia64 at -O2. The
variable v was not used after being computed, which resulted in enough
dead code elimination (DCE) to confuse the compiler and emit a bogus
warning about the use of the variable i without prior definition. The
variable i is the loop variable.
Submitted by: des
Responsibility: marcel
to select a serial console and debug port (resp). On ia64 these replace
the use of hints completely and take precedence over hints on alpha,
amd64 and i386. On sparc64 these variables are not yet recognised.
The reasons for introducing these variables are:
1. Hints have side-effects. They reserve the unit number for use by
isa or acpi devices and therefore cannot be used to select a pci
device. Also, the use of a unit number to select a device prior
to bus enumeration is nonsense. The new variables have no side-
effects and are not based on unit numbers.
2. Hints don't have the expression power to allow the sysadmin to
select UARTs that are not legacy PC devices and need the support
of compile-time constants to give the sysadmin some level of
flexibility.
The hw.uart.console and hw.uart.dbgport variables specify a list of
attributes. An attribute is a tag-value pair, seperated by a colon.
Attributes are seperated by a comma. Where possible, tags are the
same as those in /etc/remote (only br and pa in practice). Details
can be found in the manpage (not part of this commit).
Not tested on: amd64, pc98
device, the device is probed multiple times (so each device is
detected N times after unloading/loading the module N-1 times).
The real fix is (quote Doug and Warner):
> : In an ideal world, there should be some kind of BUS_UNIDENTIFY method
> : which a driver could use to delete the devices it created in
> : BUS_IDENTIFY.
>
> Or the bus would have a driver deleted routine that got called and it
> would remove all instances of the devclass attached to it.
Reviewed by: Doug Rabson & Warner Losh
mappings required by mdstart_swap(). On i386, if the ephemeral mapping
is already in the sf_buf mapping cache, a swap-backed md performs
similarly to a malloc-backed md. Even if the ephemeral mapping is not
cached, this implementation is still faster. On 64-bit platforms, this
change has the effect of using the direct virtual-to-physical mapping,
avoiding ephemeral mapping overheads, such as TLB shootdowns on SMPs.
On a 2.4GHz, 400MHz FSB P4 Xeon configured with 64K sf_bufs and
"mdmfs -S -o async -s 128m md /mnt"
before:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.430923 secs (311465697 bytes/sec)
after with cold sf_buf cache:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.367948 secs (364773576 bytes/sec)
after with warm sf_buf cache:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.252826 secs (530870010 bytes/sec)
malloc-backed md:
dd if=/dev/md0 of=/dev/null bs=64k
134217728 bytes transferred in 0.253126 secs (530240978 bytes/sec)
clip/destroy the dB value contained in the wi(4)'s receive frames,
it doesn't match with the flag set in the radiotap header
(unperturbed dB versus dBm).
mini-layer. I don't have time to bing it forward into the GEOM world, and
no one else has stepped forward to claim it. It'll be in the Attic for safe
keeping for now.
This adds support for cardbus ATA/SATA controllers. I get roughly the
same transfer speeds as on true PCI controllers. Nice to be able to add
a couble of "real" disks to a laptop :)
Only cy, bs and wd in the tree still use it. I have a replacement for
cy that I need to test on ISA and PCI cards. bs and wd are pc98 only
drivers that appear to no longer be necessary. I'll be removing them
when I hear back from the pc98 people.
attach/detach time.
Assigning the default behaviour to this particular device is
incorrect, corrupting the video BIOS aperture, and breaking
VESA support in the kernel and XFree86.
Reviewed By: dfr
MFC after: 1 week
PR: kern/62906
to build the kernel. It doesn't affect the operation if gcc.
Most of the changes are just adding __INTEL_COMPILER to #ifdef's, as
icc v8 may define __GNUC__ some parts may look strange but are
necessary.
Additional changes:
- in_cksum.[ch]:
* use a generic C version instead of the assembly version in the !gcc
case (ASM code breaks with the optimizations icc does)
-> no bad checksums with an icc compiled kernel
Help from: andre, grehan, das
Stolen from: alpha version via ppc version
The entire checksum code should IMHO be replaced with the DragonFly
version (because it isn't guaranteed future revisions of gcc will
include similar optimizations) as in:
---snip---
Revision Changes Path
1.12 +1 -0 src/sys/conf/files.i386
1.4 +142 -558 src/sys/i386/i386/in_cksum.c
1.5 +33 -69 src/sys/i386/include/in_cksum.h
1.5 +2 -0 src/sys/netinet/igmp.c
1.6 +0 -1 src/sys/netinet/in.h
1.6 +2 -0 src/sys/netinet/ip_icmp.c
1.4 +3 -4 src/contrib/ipfilter/ip_compat.h
1.3 +1 -2 src/sbin/natd/icmp.c
1.4 +0 -1 src/sbin/natd/natd.c
1.48 +1 -0 src/sys/conf/files
1.2 +0 -1 src/sys/conf/files.amd64
1.13 +0 -1 src/sys/conf/files.i386
1.5 +0 -1 src/sys/conf/files.pc98
1.7 +1 -1 src/sys/contrib/ipfilter/netinet/fil.c
1.10 +2 -3 src/sys/contrib/ipfilter/netinet/ip_compat.h
1.10 +1 -1 src/sys/contrib/ipfilter/netinet/ip_fil.c
1.7 +1 -1 src/sys/dev/netif/txp/if_txp.c
1.7 +1 -1 src/sys/net/ip_mroute/ip_mroute.c
1.7 +1 -2 src/sys/net/ipfw/ip_fw2.c
1.6 +1 -2 src/sys/netinet/igmp.c
1.4 +158 -116 src/sys/netinet/in_cksum.c
1.6 +1 -1 src/sys/netinet/ip_gre.c
1.7 +1 -2 src/sys/netinet/ip_icmp.c
1.10 +1 -1 src/sys/netinet/ip_input.c
1.10 +1 -2 src/sys/netinet/ip_output.c
1.13 +1 -2 src/sys/netinet/tcp_input.c
1.9 +1 -2 src/sys/netinet/tcp_output.c
1.10 +1 -1 src/sys/netinet/tcp_subr.c
1.10 +1 -1 src/sys/netinet/tcp_syncache.c
1.9 +1 -2 src/sys/netinet/udp_usrreq.c
1.5 +1 -2 src/sys/netinet6/ipsec.c
1.5 +1 -2 src/sys/netproto/ipsec/ipsec.c
1.5 +1 -1 src/sys/netproto/ipsec/ipsec_input.c
1.4 +1 -2 src/sys/netproto/ipsec/ipsec_output.c
and finally remove
sys/i386/i386 in_cksum.c
sys/i386/include in_cksum.h
---snip---
- endian.h:
* DTRT in C++ mode
- quad.h:
* we don't use gcc v1 anymore, remove support for it
Suggested by: bde (long ago)
- assym.h:
* avoid zero-length arrays (remove dependency on a gcc specific
feature)
This change changes the contents of the object file, but as it's
only used to generate some values for a header, and the generator
knows how to handle this, there's no impact in the gcc case.
Explained by: bde
Submitted by: Marius Strobl <marius@alchemy.franken.de>
- aicasm.c:
* minor change to teach it about the way icc spells "-nostdinc"
Not approved by: gibbs (no reply to my mail)
- bump __FreeBSD_version (lang/icc needs to know about the changes)
Incarnations of this patch survive gcc compiles since a loooong time,
I use it on my desktop. An icc compiled kernel works since Nov. 2003
(exceptions: snd_* if used as modules), it survives a build of the
entire ports collection with icc.
Parts of this commit contains suggestions or submissions from
Marius Strobl <marius@alchemy.franken.de>.
Reviewed by: -arch
Submitted by: netchild
Intel C/C++ compiler (lang/icc) to build the kernel.
The icc CPUTYPE CFLAGS use icc v7 syntax, icc v8 moans about them, but
doesn't abort. They also produce CPU specific code (new instructions
of the CPU, not only CPU specific scheduling), so if you get coredumps
with signal 4 (SIGILL, illegal instruction) you've used the wrong
CPUTYPE.
Incarnations of this patch survive gcc compiles and my make universe.
I use it on my desktop.
To use it update share/mk, add
/usr/local/intel/compiler70/ia32/bin (icc v7, works)
or
/usr/local/intel_cc_80/bin (icc v8, doesn't work)
to your PATH, make sure you have a new kernel compile directory
(e.g. MYKERNEL_icc) and run
CFLAGS="-O2 -ip" CC=icc make depend
CFLAGS="-O2 -ip" CC=icc make
in it.
Don't compile with -ipo, the build infrastructure uses ld directly to
link the kernel and the modules, but -ipo needs the link step to be
performed with Intel's linker.
Problems with icc v8:
- panic: npx0 cannot be emulated on an SMP system
- UP: first start of /bin/sh results in a FP exception
Parts of this commit contains suggestions or submissions from
Marius Strobl <marius@alchemy.franken.de>.
Reviewed by: silence on -arch
Submitted by: netchild
for Windows are deserialized miniports. Such drivers maintain their own
queues and do their own locking. This particular driver is not deserialized
though, and we need special support to handle it correctly.
Typically, in the ndis_rxeof() handler, we pass all incoming packets
directly to (*ifp->if_input)(). This in turn may cause another thread
to run and preempt us, and the packet may actually be processed and
then released before we even exit the ndis_rxeof() routine. The
problem with this is that releasing a packet calls the ndis_return_packet()
function, which hands the packet and its buffers back to the driver.
Calling ndis_return_packet() before ndis_rxeof() returns will screw
up the driver's internal queues since, not being deserialized,
it does no locking.
To avoid this problem, if we detect a serialized driver (by checking
the attribute flags passed to NdisSetAttributesEx(), we use an alternate
ndis_rxeof() handler, ndis_rxeof_serial(), which puts the call to
(*ifp->if_input)() on the NDIS SWI work queue. This guarantees the
packet won't be processed until after ndis_rxeof_serial() returns.
Note that another approach is to always copy the packet data into
another mbuf and just let the driver retain ownership of the ndis_packet
structure (ndis_return_packet() never needs to be called in this
case). I'm not sure which method is faster.
On vnode backed md(4) devices over a certain, currently undetermined
size relative to the buffer cache our "lemming-syncer" can provoke
a buffer starvation which puts the md thread to sleep on wdrain.
This generally tends to grind the entire system to a stop because the
event that is supposed to wake up the thread will not happen until a fair
bit of the piled up I/O requests in the system finish, and since a lot
of those are on a md(4) vnode backed device which is currently waiting
on wdrain until a fair amount of the piled up ... you get the picture.
The cure is to issue all VOP_WRITES on the vnode backing the device
with IO_SYNC.
In addition to more closely emulating a real disk device with a
non-lying write-cache, this makes the writes exempt from rate-limited
(there to avoid starving the buffer cache) and consequently prevents
the deadlock.
Unfortunately performance takes a hit.
Add "async" option to give people who know what they are doing the
old behaviour.
This may not be a generally valid configuration, but neither is relying
on the PCI clock to be stable.
The only currently known and supported hardware is the VPN14x1 from
Soekris, and since it has external clock, we fail safe(r) by using
it.
Unfortunately there is no way to probe this reliably.
ndis_probe_pci() doesn't contain an entry for an IRQ resource, try to
force one to be routed to us anyway by adding an extra call to
bus_alloc_resource(). If this fails, then we have to abort the attach.
Patch provided by jhb, tweaked by me.
prevented newfs to work on volumes that are larger than 1TB.
PR: 63577
Submitted by: Masaki Takakashi <mtakahashi@se.gtd.cosmo.co.jp>
Approved by: grog (mentor), bde
if_ndis.c has been split into if_ndis_pci.c and if_ndis_pccard.c.
The ndiscvt(8) utility should be able to parse device info for PCMCIA
devices now. The ndis_alloc_amem() has moved from kern_ndis.c to
if_ndis_pccard.c so that kern_ndis.c no longer depends on pccard.
NOTE: this stuff is not guaranteed to work 100% correctly yet. So
far I have been able to load/init my PCMCIA Cisco Aironet 340 card,
but it crashes in the interrupt handler. The existing support for
PCI/cardbus devices should still work as before.
The previous logic meant that if a user sets it to a minimal cooling value
acpi_thermal will not use higher cooling levels. Reverse the logic so that
the user requesting a level (say, 2) also gets 0 - 1 also.
PR: kern/61592
Submitted by: Andrew Thompson <andy@fud.org.nz>
