Now the section width is set appropriately per the BIO_DELETE
parameter being described.
Reported by: make manlint
MFC after: 1 week
Sponsored by: Dell EMC Isilon
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
VesaLocalBus or EISA. Internally, EISA and ISA are handled the same,
with VL being handled slightly differently. To avoid too much code
churn, retain the EISA name, despite it being used only for ISA
bus. When it is on the ISA bus, weird gymnastics are required with
EISA-space address accesses as well. Remove known models from the ahc
man page. Remove ahc_eisa module.
page. Remove comment about EISA dual channel card. Remove trivial
references in advlib to avoid false positives with grep. Remove stray
MCA reference not worth a seperate commit.
still relevant (ISA cards can still be in EISA mode, and we're still
ignoring those in the identify routine). Notes about cards in EISA
mode have been left in the manual since they aren't relevant to EISA
support, but instruct how to properly configure an ISA card in a mode
when it is in a ISA bus slot.
support. Fix a comment block that's shared with both vx and ep. Remove
obsolete refernce to statically compiling a kernel with a fixed number
of vx devices. Have not removed EISA from the title of the document
the register definitions were originally derived from (though no doubt
more recent docments were also consulted).
machines, only a few 486 machines that used it, and those haven't had
enough memory to run FreeBSD for quite some time (often limited to
16MB).
Not to be confused with the Machine Check Architecture, which is still
very much alive and used (and untouched by this commit).
No Objection From: arch@
Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Reviewed by: gnn, wblock
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
'-n' to tell the driver to create _up to_ 'n' queues if enough cores are
available. For example, setting hw.cxgbe.nrxq10g="-32" will result in
16 queues if the system has 16 cores, 32 if it has 32.
There is no change in the default number of queues of any type.
MFC after: 1 week
Sponsored by: Chelsio Communications
Document AF_UNIX control messages in unix(4) only, not split between unix(4)
and recv(2).
Also, warn about LOCAL_CREDS effective uid/gid fields, since the write could
be from a setuid or setgid program (with the explicit SCM_CREDS and
LOCAL_PEERCRED, the credentials are read at such a time that it can be
assumed that the process intends for them to be used in this context).
Reviewed by: wblock
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9298
This manpage isn't differentiated from mlx4en except where necessary,
replacing eth/ETH with ib/IB.
Eventually the manpages will be split and the common bits be placed
in a manpage named "mlx4.4".
MFC after: 3 weeks
Reviewed by: hselasky
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9241
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
The sysctl controls the period per interface.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D9153
drain timeout handling to historical freebsd behavior.
The primary reason for these changes is the need to have tty_drain() call
ttydevsw_busy() at some reasonable sub-second rate, to poll hardware that
doesn't signal an interrupt when the transmit shift register becomes empty
(which includes virtually all USB serial hardware). Such hardware hangs
in a ttyout wait, because it never gets an opportunity to trigger a wakeup
from the sleep in tty_drain() by calling ttydisc_getc() again, after
handing the last of the buffered data to the hardware.
While researching the history of changes to tty_drain() I stumbled across
some email describing the historical BSD behavior of tcdrain() and close()
on serial ports, and the ability of comcontrol(1) to control timeout
behavior. Using that and some advice from Bruce Evans as a guide, I've
put together these changes to implement the hardware polling and restore
the historical timeout behaviors...
- tty_drain() now calls ttydevsw_busy() in a loop at 10 Hz to accomodate
hardware that requires polling for busy state.
- The "new historical" behavior for draining during close(2) is retained:
the drain timeout is "1 second without making any progress". When the
1-second timeout expires, if the count of bytes remaining in the tty
layer buffer is smaller than last time, the timeout is extended for
another second. Unfortunately, the same logic cannot be extended all
the way down to the hardware, because the interface to that layer is a
simple busy/not-busy indication.
- Due to the previous point, an application that needs a guarantee that
all data has been transmitted must use TIOCDRAIN/tcdrain(3) before
calling close(2).
- The historical behavior of honoring the drainwait setting for TIOCDRAIN
(used by tcdrain(3)) is restored.
- The historical kern.drainwait sysctl to control the global default
drainwait time is restored, but is now named kern.tty_drainwait.
- The historical default drainwait timeout of 300 seconds is restored.
- Handling of TIOCGDRAINWAIT and TIOCSDRAINWAIT ioctls is restored
(this also makes the comcontrol(1) drainwait verb work again).
- Manpages are updated to document these behaviors.
Reviewed by: bde (prior version)
- Update struct link_settings and associated shared code.
- Add tunables to control FEC and autonegotiation. All ports inherit
these values as their initial settings.
hw.cxgbe.fec
hw.cxgbe.autoneg
- Add per-port sysctls to control FEC and autonegotiation. These can be
modified at any time.
dev.<port>.<n>.fec
dev.<port>.<n>.autoneg
MFC after: 3 days
Sponsored by: Chelsio Communications
- Drop uses of 'will'.
- Replace 'to use' with active voice.
- Tidy language around interrupt types and clarify that INTx doesn't
work on VFs.
- Drop leading articles from sysctl/tunable descriptions.
- Tweak the wording of several sysctl/tunable descriptions.
Submitted by: wblock (1, 2, 4)
Sponsored by: Chelsio Communications
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D8812
FC-Tape provides additional link level error recovery, and is
highly recommended for tape devices. It will only be turned on for
a given target if the target supports it.
Without this setting, we default to whatever FC-Tape setting is in
NVRAM on the card.
This can be overridden by setting the following loader tunable, for
example for isp0:
hint.isp.0.nofctape=1
sys/conf/options:
Add a new kernel config option, ISP_FCTAPE_OFF, that
defaults the FC-Tape configuration to off.
sys/dev/isp/isp_pci.c:
If ISP_FCTAPE_OFF is defined, turn off FC-Tape. Otherwise,
turn it on if the card supports it.
share/man/man4/isp.4:
Add a description of FC-Tape to the isp(4) man page.
Add descriptions of the fctape and nofctape options, as well as the
ISP_FCTAPE_OFF kernel configuration option.
Add the ispfw module and kernel drivers to the suggested
configurations at the top of the man page so that users are less
likely to leave it out. The driver works well with the included
firmware, but may not work at all with whatever firmware the user
has flashed on their card.
MFC after: 3 days
Sponsored by: Spectra Logic
- It should say 'read' in the I2CREAD section.
- last in the struct indicates the last command in a sequence, not the
reverse.
Reviewed by: imp
MFC after: 3 days
We shouldn't install them on the architectures not supported by Hyper-V.
And, hv_ata_pci_disengage.4.gz should be removed from all architectures:
1) It should have only applied to Hyper-V;
2) For Hyper-V platforms (amd64 and i386), the related driver was removed by
r306426 | sephe | 2016-09-29 09:41:52 +0800 (Thu, 29 Sep 2016),
because now we have a better mechanism to disble the ata driver for hard
disks when the VM runs on Hyper-V.
Reviewed by: sephe, andrew, jhb
Approved by: sephe (mentor)
MFC after: 3 days
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8572
on the AES-NI code, and modified as needed for use on ARMv8. When loaded
the driver will check the appropriate field in the id_aa64isar0_el1
register to see if AES is supported, and if so the probe function will
signal the driver should attach.
With this I have seen up to 2000Mb/s from the cryptotest test with a single
thread on a ThunderX Pass 2.0.
Reviewed by: imp
Obtained from: ABT Systems Ltd
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8297
We need to remove the line since we removed the related manual just now.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
A few months ago, we removed the driver, which was not necessary any longer.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
We enhanced the vmbus driver to support PCIe pass-through recently.
Reviewed by: sephe
Approved by: sephe (mentor)
MFC after: 1 week
Sponsored by: Microsoft
VSS stands for "Volume Shadow Copy Service". Unlike virtual machine
snapshot, it only takes snapshot for the virtual disks, so both
filesystem and applications have to aware of it, and cooperate the
whole VSS process.
This driver exposes two device files to the userland:
/dev/hv_fsvss_dev
Normally userland programs should _not_ mess with this device file.
It is currently used by the hv_vss_daemon(8), which freezes and
thaws the filesystem. NOTE: currently only UFS is supported, if
the system mounts _any_ other filesystems, the hv_vss_daemon(8)
will veto the VSS process.
If hv_vss_daemon(8) was disabled, then this device file must be
opened, and proper ioctls must be issued to keep the VSS working.
/dev/hv_appvss_dev
Userland application can opened this device file to receive the
VSS freeze notification, hold the VSS for a while (mainly to flush
application data to filesystem), release the VSS process, and
receive the VSS thaw notification i.e. applications can run again.
The VSS will still work, even if this device file is not opened.
However, only filesystem consistency is promised, if this device
file is not opened or is not operated properly.
hv_vss_daemon(8) is started by devd(8) by default. It can be disabled
by editting /etc/devd/hyperv.conf.
Submitted by: Hongjiang Zhang <honzhan microsoft com>
Reviewed by: kib, mckusick
MFC after: 3 weeks
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D8224
- Increase Rx buffer size from MCLBYTES to MJUMPAGESIZE.
- Provide an additional defragmentation routine for frames larger
than MCLBYTES; that is required by A-MSDU / Atheros Fast-Frames
support to work with current Tx path implementation.
Enabled features list for RTL8188CE:
- Atheros Fast-Frames;
- A-MPDU (Tx / Rx);
- A-MSDU (Tx / Rx; 4k only);
- Short Guard Interval.
Tested with:
- RTL8188CE (STA+AP) + RTL8821AU (STA).
- RTL8188CE (STA) + RTL8188CUS (AP).
Relnotes: yes
After removal of SMB_TRANS some information in the description of
SMB_BWRITE has become stale. E.g., the maximum block size has been
restored to 32.
Also, the descriptions of SMB_BREAD and SMB_BWRITE had some
incorrect information on the SMBus protocol details.
MFC after: 1 week
X-MFC with: r308242
Differential Revision: https://reviews.freebsd.org/D8431
This change reverts most of r281985.
The method did not map to anything defined by SMBus protocol and could
not be implemented for SMBus controllers.
This change is obviously not backwards compatible, but I have good
reasons to believe that there have never been any users of SMB_TRANS.
Discussed with: grembo, jhb
MFC after: 6 weeks
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
The driver currently supports chips that are fully compliant with the
JEDEC SPD / EEPROM / TS standard (JEDEC Standard 21-C,
TSE2002 Specification, frequenlty referred to as JEDEC JC 42.4).
Additionally some chips from STMicroelectronics are supported as well.
They are compliant except for their Device ID pattern.
Given the continued lack of any common sensor infrastructure, the driver
uses an ad-hoc sysctl to report the temperature.
Reviewed by: wblock (documentation)
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8174
These two ALU instructions first appeared on Linux. Then, libpcap adopted
and made them available since 1.6.2. Now more platforms including NetBSD
have them in kernel. So do we.
--이 줄 이하는 자동으로 제거됩니다--
All devices:
- add support for rate adaptation via ieee80211_amrr(9);
- use short preamble for transmitted frames when needed;
- multi-bss support:
* for RTL8821AU: 2 VAPs at the same time;
* other: 1 any VAP + 1 sta VAP.
RTL8188CE:
- fix IQ calibration bug (reason of significant speed degradation);
- add h/w crypto acceleration support.
USB:
- A-MPDU Tx support;
- short GI support;
Other:
- add support for RTL8812AU / RTL8821AU chipsets
(a/b/g/n only; no ac yet);
- split merged code into subparts:
* bus glue (usb/*, pci/*, rtl*/usb/*, rtl*/pci/*)
* common (if_rtwn*)
* chip-specific (rtl*/*)
- various other bugfixes.
Due to code reorganization, module names / requirements were changed too:
urtwn urtwnfw -> rtwn rtwn_usb rtwnfw
rtwn rtwnfw -> rtwn rtwn_pci rtwnfw
Tested with RTL8188CE, RTL8188CUS, RTL8188EU and RTL8821AU.
Tested by: kevlo, garga,
Peter Garshtja <peter.garshtja@ambient-md.com>,
Kevin McAleavey <kevin.mcaleavey@knosproject.com>,
Ilias-Dimitrios Vrachnis <id@vrachnis.com>,
<otacilio.neto@bsd.com.br>
Relnotes: yes
This commit, long overdue, contains contributions in the last 2 years
from Stefano Garzarella, Giuseppe Lettieri, Vincenzo Maffione, including:
+ fixes on monitor ports
+ the 'ptnet' virtual device driver, and ptnetmap backend, for
high speed virtual passthrough on VMs (bhyve fixes in an upcoming commit)
+ improved emulated netmap mode
+ more robust error handling
+ removal of stale code
+ various fixes to code and documentation (some mixup between RX and TX
parameters, and private and public variables)
We also include an additional tool, nmreplay, which is functionally
equivalent to tcpreplay but operating on netmap ports.
like other PCI network drivers. The sys/ofed directory is now mainly
reserved for generic infiniband code, with exception of the mthca driver.
- Add new manual page, mlx4en(4), describing how to configure and load
mlx4en.
- All relevant driver C-files are now prefixed mlx4, mlx4_en and
mlx4_ib respectivly to avoid object filename collisions when compiling
the kernel. This also fixes an issue with proper dependency file
generation for the C-files in question.
- Device mlxen is now device mlx4en and depends on device mlx4, see
mlx4en(4). Only the network device name remains unchanged.
- The mlx4 and mlx4en modules are now built by default on i386 and
amd64 targets. Only building the mlx4ib module depends on
WITH_OFED=YES .
Sponsored by: Mellanox Technologies
db_segsize().
Use db_segsize() to set the default operand/address size for
disassembling. Allow overriding this with the "alternate" display
format /I. The API of db_disasm() should be debooleanized to pass a
more general request (amd64 needs overrides to sizes of 16, 32, and
64, but this commit doesn't implement anything for amd64 since much
larger changes are needed to restore the amd64 disassmbler's support
for non-default sizes).
Fix db_print_loc_and_inst() to ask for the normal format and not the
alternate in normal operation.
This is most useful for vm86 mode, but also works for 16-bit protected
mode.
Use db_segsize() to avoid trying to print a garbage stack trace if %cs
is 16 bits. Print something like the stack trace termination message
for a trap boundary instead.
Document that the alternate format is now useful on i386.
AMD chipsets have proprietary mechanisms for dicovering resources.
Those resources are not discoverable via plug-and-play mechanisms
like PCI configuration registers or ACPI.
For this reason a chipset-specific knowledge of proprietary registers
is required.
At present there are two FreeBSD drivers that require the proprietary
resource discovery. One is amdsbwd which is a driver for the watchdog
timer in the AMD chipsets. The other is intpm SMBus driver when it
attaches to the newer AMD chipsets where the resources of the SMBus HBA
are not described in the regular PCI way.
In both cases the resources are discovered by accessing AMD PMIO space.
Thus, many definitions are shared between the two drivers.
This change puts those defintions into a common header file.
As an added benefit, intpm driver now supports newest FCHs built into
AMD processors of Family 15h, models 70h-7Fh and Family 16h, models
30h-3Fh.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8004
Now that all of the necessary bits for ARMv6 support for CloudABI have
been checked in, let's hook the kernel module up to the build and
document its existence.
This is an RTL8168 chip, which we already support so all we have to do is add
the vendor ID.
PR: 212876
Submitted by: Tobias Kortkamp <t@tobik.me>
MFC after: 3 days
it. This arg is most interesting for the 'break' command where it
never worked, and for the step command where it is powerful but too
fragile to use much.
Give the full syntax of the 'addr' arg for these commands and some
others. Rename it from 'address' for the generic command.
Fix description of how 'count' is supposed to work for the 'break'
command.
Don't (mis)describe the syntax of the comma for the 'step' command.
Expand the description for the generic command.
Give the full syntax for the 'examine' command. It was also missing
the possible values for the modifier.
Fix mdoc syntax error for the 'search' command.
Remove FUD about consequences of not having a trap handler for the
'search' command.
Describe PCI-related kernel options for HotPlug and SR-IOV support in the
pci(4) manual page. While here, add a section describing the various
tunables supported by the PCI bus driver as well.
Reviewed by: wblock
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7754
The cxgbev/cxlv driver supports Virtual Function devices for Chelsio
T4 and T4 adapters. The VF devices share most of their code with the
existing PF4 driver (cxgbe/cxl) and as such the VF device driver
currently depends on the PF4 driver.
Similar to the cxgbe/cxl drivers, the VF driver includes a t4vf/t5vf
PCI device driver that attaches to the VF device. It then creates
child cxgbev/cxlv devices representing ports assigned to the VF.
By default, the PF driver assigns a single port to each VF.
t4vf_hw.c contains VF-specific routines from the shared code used to
fetch VF-specific parameters from the firmware.
t4_vf.c contains the VF-specific PCI device driver and includes its
own attach routine.
VF devices are required to use a different firmware request when
transmitting packets (which in turn requires a different CPL message
to encapsulate messages). This alternate firmware request does not
permit chaining multiple packets in a single message, so each packet
results in a firmware request. In addition, the different CPL message
requires more detailed information when enabling hardware checksums,
so parse_pkt() on VF devices must examine L2 and L3 headers for all
packets (not just TSO packets) for VF devices. Finally, L2 checksums
on non-UDP/non-TCP packets do not work reliably (the firmware trashes
the IPv4 fragment field), so IPv4 checksums for such packets are
calculated in software.
Most of the other changes in the non-VF-specific code are to expose
various variables and functions private to the PF driver so that they
can be used by the VF driver.
Note that a limited subset of cxgbetool functions are supported on VF
devices including register dumps, scheduler classes, and clearing of
statistics. In addition, TOE is not supported on VF devices, only for
the PF interfaces.
Reviewed by: np
MFC after: 2 months
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D7599
This driver only supports 10Mb Ethernet using PIO (the hardware supports
DMA, but the driver only does PIO). There are not any PCCard adapters
supported by this driver, only ISA cards. In addition, it does not use
bus_space but instead uses bcopy with volatile pointers triggering a
host of warnings. (if_ie.c is one of 3 files always built with
-Wno-error)
Relnotes: yes
This hardware is not present on any modern systems. The driver is quite
hackish (raw inb/outb instead of bus_space, and raw inb/outb to random
I/O ports to enable ACPI since it predated proper ACPI support).
Relnotes: yes
The wl(4) driver supports pre-802.11 PCCard wireless adapters that
are slower than 802.11b. They do not work with any of the 802.11
framework and the driver hasn't been reported to actually work in a
long time.
Relnotes: yes
The si(4) driver supported multiport serial adapters for ISA, EISA, and
PCI buses. This driver does not use bus_space, instead it depends on
direct use of the pointer returned by rman_get_virtual(). It is also
still locked by Giant and calls for patch testing to convert it to use
bus_space were unanswered.
Relnotes: yes
