bhyve was recently sandboxed with capsicum, and needs to be able to
control the CPU sets of its vcpu threads
Reviewed by: emaste, oshogbo, rwatson
MFC after: 2 weeks
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D10170
ENA is a networking interface designed to make good use of modern CPU
features and system architectures.
The ENA device exposes a lightweight management interface with a
minimal set of memory mapped registers and extendable command set
through an Admin Queue.
The driver supports a range of ENA devices, is link-speed independent
(i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc.), and has
a negotiated and extendable feature set.
Some ENA devices support SR-IOV. This driver is used for both the
SR-IOV Physical Function (PF) and Virtual Function (VF) devices.
ENA devices enable high speed and low overhead network traffic
processing by providing multiple Tx/Rx queue pairs (the maximum number
is advertised by the device via the Admin Queue), a dedicated MSI-X
interrupt vector per Tx/Rx queue pair, and CPU cacheline optimized
data placement.
The ENA driver supports industry standard TCP/IP offload features such
as checksum offload and TCP transmit segmentation offload (TSO).
Receive-side scaling (RSS) is supported for multi-core scaling.
The ENA driver and its corresponding devices implement health
monitoring mechanisms such as watchdog, enabling the device and driver
to recover in a manner transparent to the application, as well as
debug logs.
Some of the ENA devices support a working mode called Low-latency
Queue (LLQ), which saves several more microseconds. This feature will
be implemented for driver in future releases.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Jakub Palider <jpa@semihalf.com>
Jan Medala <jan@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10427
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
This includes NVMe device support and adds support for the following adapters:
SAS 3408
SAS 3416
SAS 3508
SAS 3516
SAS 3616
SAS 3708
SAS 3716
Reviewed by: ken, scottl, asomers, mav
Approved by: ken, scottl, mav
MFC after: 2 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D10095
This will help application developers simulate end of tape conditions.
To inject an error in sa0:
sysctl kern.cam.sa.0.inject_eom=1
This will return the next read or write request queued with 0 bytes
written. Any subsequent writes or reads will go along as usual.
This will also cause the early warning position flag to get set
for the next position query. So, 'mt status' will show the BPEW
(Beyond Programmable Early Warning) flag on the first query after
an error injection. After that, the position flags will be as they
are in the underlying tape drive.
Also, update the sa(4) man page to describe tape parameters,
which can be set via 'mt param'.
sys/cam/scsi/scsi_sa.c:
In saregister(), create the inject_eom sysctl variable.
In sastart(), check to see whether inject_eom is set. If
so, return the read or write with 0 bytes written to
indicate EOM. Set the set_pews_status flag so that we
fake PEWS status in the next position call for reads, and the
next 3 calls for writes. This allows the user to see the BPEW
flag one time via 'mt status'.
In sagetpos(), check the set_pews_status flag and fake
PEWS status and decrement the counter if it is set.
share/man/man4/sa.4:
Document the inject_eom sysctl variable.
Document all of the parameters currently supported via
'mt param'.
usr.bin/mt/mt.1:
Point the user to the sa(4) man page for more details on
supported parameters.
MFC after: 3 days
Sponsored by: Spectra Logic
After FreeBSD SVN revision 236814, the pass(4) driver changed from
only doing error recovery when the CAM_PASS_ERR_RECOVER flag was
set on a CCB to sometimes doing error recovery if the passed in
retry count was non-zero.
Error recovery would happen if two conditions were met:
1. The error recovery action was simply a retry. (Which is most
cases.)
2. The retry_count is non-zero. (Which happened a lot because of
cut-and-pasted code.)
This explains a bug I noticed in with camcontrol:
# camcontrol tur da34 -v
Unit is ready
# camcontrol reset da34
Reset of 1:172:0 was successful
At this point, there should be a Unit Attention:
# camcontrol tur da34 -v
Unit is ready
No Unit Attention.
Try it again:
# camcontrol reset da34
Reset of 1:172:0 was successful
Now set the retry_count to 0 for the TUR:
# camcontrol tur da34 -v -C 0
Unit is not ready
(pass42:mps1:0:172:0): TEST UNIT READY. CDB: 00 00 00 00 00 00
(pass42:mps1:0:172:0): CAM status: SCSI Status Error
(pass42:mps1:0:172:0): SCSI status: Check Condition
(pass42:mps1:0:172:0): SCSI sense: UNIT ATTENTION asc:29,2 (SCSI bus reset occurred)
(pass42:mps1:0:172:0): Field Replaceable Unit: 2
There is the unit attention. camcontrol(8) has a default
retry_count of 1, in case someone sets the -E flag without
setting -C.
The CAM_PASS_ERR_RECOVER behavior was only broken with the
CAMIOCOMMAND ioctl, which is the synchronous pass(4) API. It has
worked as intended (error recovery is only done when the flag
is set) in the asynchronous API (CAMIOQUEUE ioctl).
sys/cam/scsi/scsi_pass.c:
In passsendccb(), when calling cam_periph_runccb(), only
specify the error routine when CAM_PASS_ERR_RECOVER is set.
share/man/man4/pass.4:
Document that CAM_PASS_ERR_RECOVER is needed to enable
error recovery.
Reported by: Terry Kennedy <TERRY@glaver.org>
PR: kern/218572
MFC after: 1 week
Sponsored by: Spectra Logic
1. Wrap at <80 columns for readability when editing. Rewrap some lines
prematurely wrapped to better fit in <80 columns and not waste
vertical space.
2. Fix SEE ALSO sorting (sort by section first, then manpage name).
3. Tweak the compound device description slightly by adding soft stops
via commas.
MFC after: 1 week
Reported by: igor [3], manlint [2]
Sponsored by Dell EMC Isilon
patm(4) devices.
Maintaining an address family and framework has real costs when we make
infrastructure improvements. In the case of NATM we support no devices
manufactured in the last 20 years and some will not even work in modern
motherboards (some newer devices that patm(4) could be updated to
support apparently exist, but we do not currently have support).
With this change, support remains for some netgraph modules that don't
require NATM support code. It is unclear if all these should remain,
though ng_atmllc certainly stands alone.
Note well: FreeBSD 11 supports NATM and will continue to do so until at
least September 30, 2021. Improvements to the code in FreeBSD 11 are
certainly welcome.
Reviewed by: philip
Approved by: harti
FDC_DEBUG is not referenced in any c or header files but traces of it
still remain in other files.
PR: 105608
Reported by: Eugene Grosbein <ports AT grosbein DOT net>
Reviewed by: imp
Approved by: bcr (mentor)
MFC after: 7 days
Differential Revision: https://reviews.freebsd.org/D10303
The goal of this work is to remove the explicit dependency for ctl(4)
on iscsi(4), so end-users without iscsi(4) support in the kernel can
use ctl(4) for its other functions.
This allows those without iscsi(4) support built into the kernel to use
ctl(4) as a test mechanism. As a sidenote, this was possible around the
10.0-RELEASE period, but made impossible for end-users without iscsi(4)
between 10.0-RELEASE and 11.0-RELEASE.
Automatically load cfiscsi(4) from ctladm(8) and ctld(8) for backwards
compatibility with previously releases. The automatic loading feature is
compiled into the beforementioned tools if MK_ISCSI == yes when building
world.
Add a manpage for cfiscsi(4) and refer to it in ctl(4).
Differential Revision: D10099
MFC after: 2 months
Relnotes: yes
Reviewed by: mav, trasz
Sponsored by: Dell EMC Isilon
Document work done by mmacy/sbruno to merge the two drivers together
and convert em(4) to the iflib framework.
X-MFC with: r311849
Sponsored by: Dell EMC Isilon
Unfortunately they will have different integer value due to Linux value being already assigned in FreeBSD.
The patch is similar to IP_RECVDSTADDR but also provides the destination port value to the application.
This allows/improves implementation of transparent proxies on UDP sockets due to having the whole information on forwarded packets.
Reviewed by: adrian, aw
Approved by: ae (mentor)
Sponsored by: rsync.net
Differential Revision: D9235
- Delete empty Li macro uses [1]. This removes some spaces between
the optional command/subcommand arguments.
- Attempt to clarify "show lock" subcommand by being more
terse/direct. This addresses an issue with a contraction [2].
MFC after: 1 week
Reported by: make manlint [1], igor [2]
Reviewed by: wblock
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9858
- Add missing sections for .Xr references.
- Replace .br with .Pp (the former macro is deprecated).
- Use the .Sx (section reference) macro when referring to
LIBRARIES, not the .Xr (cross-reference) macro.
- Add commas after "e.g." and "i.e." [*].
Bump .Dd for the change
Approved by: luigi
MFC after: 1 week
Reported by: igor [*], make manlint
Sponsored by: Dell EMC Isilon
Differential Revision: D9859
- Replace the "following lines" with more terse phrases.
- Use .Lk for the mellanox URL.
- Reword the SUPPORT section so it's less wordy.
The DESCRIPTION section suggestions are still outstanding; improving
the section requires additional review to make sure the nuance/message
is correct per the original intent.
Bump .Dd for the change
Submitted by: wblock
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9241
The driver manpage for wpifw(4) is missing, but will be added soon. This
fixes the other 2 .Xr calls lacking sections to match the 3rd,
syntactically correct, reference in the SEE ALSO section.
MFC after: 1 week
Reported by: make manlint
Sponsored by: Dell EMC Isilon
