drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
components instead of with the kernel and/or modules. This ensures that it
gets built with the host compiler, not the compiler in obj/... used to build
the target components (which may be a cross-compiler outputting code for a
different architecture and using header files with types and options set up
for the wrong architecture).
Reviewed by: imp
command register. The lazy BAR allocation code in FreeBSD sometimes
disables this bit when it detects a range conflict, and will re-enable
it on demand when a driver allocates the BAR. Thus, the bit is no longer
a reliable indication of capability, and should not be checked. This
results in the elimination of a lot of code from drivers, and also gives
the opportunity to simplify a lot of drivers to use a helper API to set
the busmaster enable bit.
This changes fixes some recent reports of disk controllers and their
associated drives/enclosures disappearing during boot.
Submitted by: jhb
Reviewed by: jfv, marius, achadd, achim
MFC after: 1 day
SVN r95378 refactored ahc_9005_subdevinfo_valid out into a separate
function but swapped the vendor/subvendor and device/subdevice pairs of
the parameters.
Found by: Coverity Prevent, CID 744931
Reviewed by: gibbs
every architecture's busdma_machdep.c. It is done by unifying the
bus_dmamap_load_buffer() routines so that they may be called from MI
code. The MD busdma is then given a chance to do any final processing
in the complete() callback.
The cam changes unify the bus_dmamap_load* handling in cam drivers.
The arm and mips implementations are updated to track virtual
addresses for sync(). Previously this was done in a type specific
way. Now it is done in a generic way by recording the list of
virtuals in the map.
Submitted by: jeff (sponsored by EMC/Isilon)
Reviewed by: kan (previous version), scottl,
mjacob (isp(4), no objections for target mode changes)
Discussed with: ian (arm changes)
Tested by: marius (sparc64), mips (jmallet), isci(4) on x86 (jharris),
amd64 (Fabian Keil <freebsd-listen@fabiankeil.de>)
to attach to target capable HBAs that implement the old immediate
notify (XPT_IMMED_NOTIFY) and notify acknowledge (XPT_NOTIFY_ACK)
CCBs. The new API has been in place since SVN change 196008 in
2009.
The solution is two-fold: fix CTL to handle the responses from the
HBAs, and convert the HBA drivers in question to use the new API.
These drivers have not been tested with CTL, so how well they will
interoperate with CTL is unknown.
scsi_target.c: Update the userland target example code to use the
new immediate notify API.
scsi_ctl.c: Detect when an immediate notify CCB is returned
with CAM_REQ_INVALID or CAM_PROVIDE_FAIL status,
and just free it.
Fix a duplicate assignment.
aic79xx.c,
aic79xx_osm.c: Update the aic79xx driver to use the new API.
Target mode is not enabled on for this driver, so
the changes will have no practical effect.
aic7xxx.c,
aic7xxx_osm.c: Update the aic7xxx driver to use the new API.
sbp_targ.c: Update the firewire target code to work with the
new API.
mpt_cam.c: Update the mpt(4) driver to work with the new API.
Target mode is only enabled for Fibre Channel
mpt(4) devices.
MFC after: 3 days
EARLY_BUILD macro: the -Qunused-arguments flag isn't passed anymore when
building this particular program. However, with clang 3.1 and -Werror,
such unused argument warnings are flagged as errors, causing buildkernel
to fail at this stage, due to the -nostdinc flag passed during linking.
Since the -nostdinc flag isn't actually needed, just remove it.
X-MFC-With: r236528
This support has not worked for several years, and is not likely to work
again, unless Intel decides to release a native FreeBSD version of their
compiler. ;)
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
The code in question verifies that all register write operations only change
bits that are defined (in the register definition file) for that effected
register. The bug effectively disabled this checking.
o Fix the check by testing the opcode against all supported read ("and" based)
operands.
o Add missing bit definitions to the aic7xxx and aic79xx register definition
files so that the warning (treated as a fatal error) does not spuriously
fire.
Reported by: Pawel Worach <pawel.worach@gmail.com>
MFC after: 1 week
Unfortunately there are two slight problems with that:
- Yacc and lex might generate code that generates warnings because of
this. Require yacc and lex to be rebuilt during bootstrap. I'm not
incrementing __FreeBSD_version here, because I assume someone else
will do this eventually.
- When running `make buildkernel', it uses share/mk from the source
treeo to build aicasm. Because aicasm also depends on lex, this would
break. Lower WARNS to 5 for now. We should just increment it to 6
again somewhere in the very far future.
errors. So far 3 different classes are present (correctable,
uncorrectable and fatal) but more can be added easilly.
Obtained from: Sandvine Incorporated
Reviewed by: emase, gibbs
Sponsored by: Sandvine Incorporated
MFC: 2 weeks
modularize it so that new transports can be created.
Add a transport for SATA
Add a periph+protocol layer for ATA
Add a driver for AHCI-compliant hardware.
Add a maxio field to CAM so that drivers can advertise their max
I/O capability. Modify various drivers so that they are insulated
from the value of MAXPHYS.
The new ATA/SATA code supports AHCI-compliant hardware, and will override
the classic ATA driver if it is loaded as a module at boot time or compiled
into the kernel. The stack now support NCQ (tagged queueing) for increased
performance on modern SATA drives. It also supports port multipliers.
ATA drives are accessed via 'ada' device nodes. ATAPI drives are
accessed via 'cd' device nodes. They can all be enumerated and manipulated
via camcontrol, just like SCSI drives. SCSI commands are not translated to
their ATA equivalents; ATA native commands are used throughout the entire
stack, including camcontrol. See the camcontrol manpage for further
details. Testing this code may require that you update your fstab, and
possibly modify your BIOS to enable AHCI functionality, if available.
This code is very experimental at the moment. The userland ABI/API has
changed, so applications will need to be recompiled. It may change
further in the near future. The 'ada' device name may also change as
more infrastructure is completed in this project. The goal is to
eventually put all CAM busses and devices until newbus, allowing for
interesting topology and management options.
Few functional changes will be seen with existing SCSI/SAS/FC drivers,
though the userland ABI has still changed. In the future, transports
specific modules for SAS and FC may appear in order to better support
the topologies and capabilities of these technologies.
The modularization of CAM and the addition of the ATA/SATA modules is
meant to break CAM out of the mold of being specific to SCSI, letting it
grow to be a framework for arbitrary transports and protocols. It also
allows drivers to be written to support discrete hardware without
jeopardizing the stability of non-related hardware. While only an AHCI
driver is provided now, a Silicon Image driver is also in the works.
Drivers for ICH1-4, ICH5-6, PIIX, classic IDE, and any other hardware
is possible and encouraged. Help with new transports is also encouraged.
Submitted by: scottl, mav
Approved by: re
the command set (only so long as the module is present):
o add db_command_register and db_command_unregister to add and remove
commands, respectively
o replace linker sets with SYSINIT's (and SYSUINIT's) that register
commands
o expose 3 list heads: db_cmd_table, db_show_table, and db_show_all_table
for registering top-level commands, show operands, and show all operands,
respectively
While here also:
o sort command lists
o add DB_ALIAS, DB_SHOW_ALIAS, and DB_SHOW_ALL_ALIAS to add aliases
for existing commands
o add "show all trace" as an alias for "show alltrace"
o add "show all locks" as an alias for "show alllocks"
Submitted by: Guillaume Ballet <gballet@gmail.com> (original version)
Reviewed by: jhb
MFC after: 1 month
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
