* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.
* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.
The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.
Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.
hardware imposes strict limitations on hard buffer and block sizes.
Previous code set soft buffer to be no smaller then hard buffer. On some
cards with fixed 64K physical buffer that caused up to 800ms play latency.
New code allows to set soft buffer size down to just two blocks of the hard
buffer and to not write more then that size ahead to the hardware buffer.
As result of that change I was able to reduce full practically measured
record-playback loop delay in those conditions down to only about 115ms
with theoretical playback latency of only about 50ms.
New code works fine for both vchans and direct cases. In both cases sound(4)
tries to follow hw.snd.latency_profile and hw.snd.latency values and
application-requested buffer and block sizes as much as limitation of two
hardware blocks allows.
Reviewed by: silence on multimedia@
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
any thread doing an I/O RPC with a transfer size greater than
NFS_UDPMAXDATA will be hung indefinitely, retrying the RPC.
After a discussion on freebsd-fs@, I decided to add a warning
message for this case, as suggested by Jeremy Chadwick.
Suggested by: freebsd at jdc.parodius.com (Jeremy Chadwick)
MFC after: 2 weeks
under the subject "F_RDLCK lock to FreeBSD NFS fails to R/O target file".
This occurred because the server side NLM always checked for VWRITE
access, irrespective of the type of lock request. This patch
replaces VOP_ACCESS(..VWRITE..) with one appropriate to
the lock operation. It allows unlock and lock cancellation
to be done without a check of VOP_ACCESS(), so that files
can't be left locked indefinitely after the file permissions
have been changed.
Discussed with: zack
Submitted by: jwd (earlier version)
Reviewed by: dfr
MFC after: 2 weeks
compliance testing.
In order to allow for radar pattern matching to occur, the DFS CAC/NOL
handling needs to be made configurable. This commit introduces a new
sysctl, "net.wlan.dfs_debug", which controls which DFS debug mode
net80211 is in.
* 0 = default, CSA/NOL handling as per normal.
* 1 = announce a CSA, but don't add the channel to the non-occupy list
(NOL.)
* 2 = disable both CSA and NOL - only print that a radar event occured.
This code is not compiled/enabled by default as it breaks regulatory
handling. A user must enable IEEE80211_DFS_DEBUG in their kernel
configuration file for this option to become available.
Obtained from: Atheros
* For legacy NICs, the combined RSSI should be used.
For earlier AR5416 NICs, use control chain 0 RSSI rather than combined
RSSI.
For AR5416 > version 2.1, use the combined RSSI again.
* Add in a missing AR5212 HAL method (get11nextbusy) which may be called
by radar code.
This serves no functional change for what's currently in FreeBSD.
about new child not only when doing PT_TO_SCX, but also for PT_CONTINUE.
If TDB_FORK flag is set, always issue a stop, the same as is done for
TDB_EXEC.
Reported by: Dmitry Mikulin <dmitrym juniper net>
MFC after: 1 week
that instead of using direct I/O it allows read-ahead similar to
POSIX_FADV_NORMAL, but invokes VOP_ADVISE(POSIX_FADV_DONTNEED) after the
read(2) has completed to purge just-read data. The write(2) path continues
to use direct I/O for POSIX_FADV_NOREUSE for now. Note that NOREUSE works
optimally if an application reads and writes full fs blocks.
that we have the lock now. This cleans up a locking panic ASSERT when
knlist_empty is called without a lock when INVARIANTS etc. are turned.
Reviewed by: kib jhb
MFC after: 1 week
so try harder to get the CDMA sync interrupt delivered and also in
a more efficient way:
- wrap the whole process of sending and receiving the CDMA sync
interrupt in a critical section so we don't get preempted,
- send the CDMA sync interrupt to the CPU that is actually waiting
for it to happen so we don't take a detour via another CPU,
- instead of waiting for up to 15 seconds for the interrupt to
trigger try the whole process for up to 15 times using a one
second timeout (the code was also changed to just ignore belated
interrupts of a previous tries should they appear).
According to testing done by Peter Jeremy with the debugging also
added as part of this commit the first two changes apparently are
sufficient to now properly get the CDMA sync interrupts delivered
at the first try though.
VIS-based block copy/zero implementations. While with 4BSD it's
sufficient to just disable the tick interrupts, with ULE+PREEMPTION
it's otherwise also possible that these are preempted via IPIs.
* Grab the net80211com lock when calling ieee80211_dfs_notify_radar().
* Use the tsf extend function to turn the 64 bit base TSF into a per-
frame 64 bit TSF. This will improve radiotap logging (which will
now have a (more) correct per-frame TSF, rather then the single TSF64
value read at the beginning of ath_rx_proc().
primitives by breaking stop_scheduler into a per-thread variable.
Also, store the new td_stopsched very close to td_*locks members as
they will be accessed mostly in the same codepaths as td_stopsched and
this results in avoiding a further cache-line pollution, possibly.
STOP_SCHEDULER() was pondered to use a new 'thread' argument, in order to
take advantage of already cached curthread, but in the end there should
not really be a performance benefit, while introducing a KPI breakage.
In collabouration with: flo
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
helper since r230632, use these for output and panicing during the
early cycles and move cninit() until after the static per-CPU data
has been set up. This solves a couple of issue regarding the non-
availability of the static per-CPU data:
- panic() not working and only making things worse when called,
- having to supply a special DELAY() implementation to the low-level
console drivers,
- curthread accesses of mutex(9) usage in low-level console drivers
that aren't conditional due to compiler optimizations (basically,
this is the problem described in r227537 but in this case for
keyboards attached via uart(4)). [1]
PR: 164123 [1]
implementing a simple OF_panic() that may be used during the early
cycles when panic() isn't available, yet.
- Mark cpu_{exit,shutdown}() as __dead2 as appropriate.
VM_KMEM_SIZE_SCALE to 2, awaiting more insight from alc@. As it turns
out, the VM apparently has problems with machines that have large holes
in the physical address space, causing the kmem_suballoc() call in
kmeminit() to fail with a VM_KMEM_SIZE_SCALE of 1. Using a value of 2
allows these, namely Blade 1500 with 2GB of RAM, to boot.
PR: 164227
cards powering up at once. Work around the easy case (multiple cards
inserted on boot) with a short sleep and a long comment. This
improves reliability on those laptops with power hungry cards.
excluding other allocations including UMA now entails the addition of
a single flag to kmem_alloc or uma zone create
Reviewed by: alc, avg
MFC after: 2 weeks
cleared/dropped leading to qid2tap[n] being NULL as there no longer
is a tap. Now, if there have been lots of frames queued the firmware
processes and returns those after the tap is gone.
Tested by: osa
MFC after: 1 week
