the AP doesn't transmit beacons.
If the AP requests a CSA (ie, a channel switch) and then enters CAC
(channel availability check) for 60 seconds, it doesn't send beacons
and it just listens for radar events (and other things which we don't
do yet.)
Now, ath_newstate() was not resetting the beacon timer config on
a transition to the RUN state when in STA mode - it was setting
sc_syncbeacon, which simply updates the beacon config from the
contents of the next received beacon.
This means the STA never generates beacon miss events.
If the AP goes into CAC for 60 seconds and recovers, the STA will
happily receive the first beacon and reconfigure timers.
But if it gets a radar event after that, it'll change channel
again, not notify the station that it's changed channel..
and since the station is happily waiting for the first beacon
to configure the beacon timer details from, it won't ever
generate a beacon miss interrupt and it'll sit there forever
(or until the AP appears on that channel once again.)
This change forces the last known beacon timer config to be
written to hardware on a transition from CSA->RUN in STA mode.
This forces bmiss events to occur and the STA will eventually
(after a handful of beacon miss events) begin scanning for
another access point.
to do with global namespaces) and CAPABILITIES (which has to do with
constraining file descriptors). Just in case, and because it's a better
name anyway, let's move CAPABILITIES out of the way.
Also, change opt_capabilities.h to opt_capsicum.h; for now, this will
only hold CAPABILITY_MODE, but it will probably also hold the new
CAPABILITIES (implying constrained file descriptors) in the future.
Approved by: rwatson
Sponsored by: Google UK Ltd
for resolving by a child process that, upon success, will add the entry
to the config of the running running parent process.
Unfortunately there are a couple of bugs with this, fixed in various
later versions of upstream in potentially different ways due to other
code changes:
1) Upon server [-46] <FQDN> the [-46] are used as FQDN for later resolving
which does not work. Make sure we always pass the name (or IP there).
2) The intermediate file to carry the information to the child process
does not know about -4/-6 restrictions, so that a dual-stacked host
could resolve to an IPv6 address but that might be unreachable (see
r223626) leading to no working synchronization ignoring a IPv4 record.
Thus alter the intermediate format to also pass the address family
(AF_UNSPEC (default), AF_INET or AF_INET6) to the child process
depending on -4 or -6.
3) Make the child process to parse the new intermediate file format and
save the address family for getaddrinfo() hints flags.
4) Change child to always reload resolv.conf calling res_init() before
trying to resolve names. This will pick up resolv.conf changes or
new resolv.confs should they have not existed or been empty or
unusable on ntp startup. This fix is more conditional in upstream
versions but given FreeBSD has res_init there is no need for the
configure logic as well.
Approved by: roberto
Sponsored by: Sandvine Incorporated
MFC after: 9 days
possible to organize subroutines with rules.
The "call" action saves the current rule number in the internal
stack and rules processing continues from the first rule with
specified number (similar to skipto action). If later a rule with
"return" action is encountered, the processing returns to the first
rule with number of "call" rule saved in the stack plus one or higher.
Submitted by: Vadim Goncharov
Discussed by: ipfw@, luigi@
This is really a new name for SNDCTL_DSP_RESET.
And this what commit r222723 should really have been in the first place.
PR: kern/156874
Submitted by: gerald
MFC after: 1 week
The commit intended to add SNDCTL_DSP_HALT, but actually added
SNDCTL_SEQ_HALT, which is not defined in the OSS specs.
Reported by: Pan Tsu <inyaoo@gmail.com>
Pointyhat to: gerald, avg
This fixes the problem, when the secondary GPT header is not erased when
partition table destroyed. Move equal operations from g_part_gpt_create
and g_part_gpt_recover to the separate function g_gpt_set_defaults.
Reported by: dwhite
MFC after: 1 week
mode attribute in as 0 when doing writes. The change adds
the Mode attribute plus the others except Owner and Owner_group
to the list requested by the NFSv4 Write Operation. This fixed
a problem where an executable file built by "cc" would get mode
0111 instead of 0755 for some NFSv4 servers.
Found at the recent NFSv4 interoperability Bakeathon.
Tested by: tdh at excfb.com
MFC after: 2 weeks
disk if needed. This should fix a potential case when extents are cleared in
activemap but metadata is not updated on disk.
Suggested by: pjd
Approved by: pjd (mentor)
stating if we need to update activemap on disk. This makes keepdirty
serve its purpose -- to reduce number of metadata updates.
Discussed with: pjd
Approved by: pjd (mentor)
get it out of a stuck condition that can be caused by GEM_MAC_RX_OVERFLOW.
- In gem_reset_rxdma() call gem_setladrf() in order to reprogram the RX
filter and restore the previous content of GEM_MAC_RX_CONFIG. While at it
consistently use the newly introduced sc_mac_rxcfg throughout the driver
instead of reading the its old content.
- Increment if_iqdrops instead of if_ierrors in case of RX buffer allocation
failure.
- According to the GEM datasheet the RX MAC should also be disabled in
gem_setladrf() before changing its configuration.
- Add error messages to gem_disable_{r,t}x() and take advantage of these
throughout the driver instead of duplicating their functionality all over
the place.
In joint forces with: yongari
in host byte order, so we need to compare them as such.
Properly compare IPv6 addresses as well.
This allows the, by default, 8 badaddrs slots per address
family to work correctly and only print sendto() errors once.
The change is no longer applicable to any latest upstream versions.
Approved by: roberto
Sponsored by: Sandvine Incorporated
MFC after: 1 week
(i.e. under COMPAT_FREEBSD32) in case ifconf() returned success to match
the native SIOCGIFCONF behavior.
PR: kern/158369
Reported by: Paul Procacci <pprocacci att gmail com>
MFC after: 1 week
For snapshots, this is the same as COMPRESSRATIO, but for
filesystems/volumes, the COMPRESSRATIO is based on the data "USED" (ie,
includes blocks in children, but not blocks shared with the origin).
This is needed to figure out how much space a filesystem would use if it
were not compressed (ignoring snapshots).
Illumos-gate revision: 13387
Obtained from: Illumos (Feature #1092)
MFC after: 2 weeks
The vdev cache is very underutilized (hit ratio 30%-70%) and may consume
excessive memory on systems with many vdevs.
Illumos-gate revision: 13346
Obtained from: Illumos (Bug #175)
MFC after: 1 week
In userland, sign extend the offset for JA instructions.
We currently use that to implement "ip6 protochain", and "pc" might be
wider than "pc->k", in which case we need to arrange that "pc->k" be
sign-extended, by casting it to bpf_int32.
PR: kern/157188
Submitted by: plosher
MFC after: 2 weeks
the microcode caused SCB timeouts. Linux driver does not allow
microcode loading for these controllers and jfv also confirmed that
there is no need to do and it shouldn't.
PR: kern/103332
Additional confirmation from: jfv
MFC after: 1 week
floppies, so it will not be used as the start of an emulated floppy
image on a bootable CD which is what the fake BPB was used for.
- Only check that EDD packet mode is available once at the start of
zfsldr rather than for each disk sector now that we read data in one
sector at a time. As a result, collapse the remaining bits of read
up into nread and rename nread to read.
- Restore a return at the end of putstr that I removed in the previous
revision.
Tested by: Henri Hennebert (earlier version)
MFC after: 1 week
Remove message about non empty bootcode, we can not break something
while GEOM_PART_EBR_COMPAT is defined.
But without GEOM_PART_EBR_COMPAT any changes in EBR are allowed and we
can accidentally wipe the boot code. To do not break anything save
the first EBR chunk and keep it untouched each time when we are
changing EBR. Note that we are still not support boot code for EBR.
PR: kern/141235
MFC after: 1 month
disk drive. The boot0cfg(8) utility preserves these 4 bytes when is
writing bootcode to keep a multiboot ability.
Change gpart's bootcode method to keep DSN if it is not zero. Also
do not allow writing bootcode with size not equal to MBRSIZE.
PR: kern/157819
Tested by: Eir Nym
MFC after: 1 month
is defined, but then proceeds to use a hardcoded maximum hostname length
of 64 anyway. Fix this by checking against MAXHOSTNAMELEN instead.
PR: bin/157732
MFC after: 3 days
