The XC900M acts as a Ubiquiti XR9 (and I _think_ SR9) by default;
it uses the same 900MHz<->2.4GHz downconverter mapping.
However it has an alternative frequency mapping which squeezes in a couple
more half/quarter rate channels. Since the default HAL doesn't support
fractional tuning (sub-1MHz) in 2.4GHz mode on the AR5413/AR5414, they
implement it using a jumper.
Datasheet: http://www.xagyl.com/download/XC900M_Datasheet.pdf
Thankyou to Xagyl Communications for the XC900M NICs and Edgar Martinez
for organising the donation.
Tested:
* XC900M <-> XC900M
* Ubiquiti XR9 <-> XC900M
TODO:
* Test against SR9 and GZ901 if possible (the IEEE channel<->frequency
mapping may not match up, thanks to the slightly different channels
involved)
EPROTONOSUPPORT if the address family is not supported.
- introduce pffinddomain() to find a domain by family and use it as
appropriate.
Reviewed by: glebius
id hash. If a state has been disconnected from id hash, its rule pointers
can no longer be dereferenced, and referenced memory can't be modified.
Thus, move rule statistics from pf_free_rule() to pf_unlink_rule() and
update them prior to releasing id hash slot lock.
Reported by: Ian FREISLICH <ianf cloudseed.co.za>
from pfsync:
- Call into pfsync_delete_state() holding the state lock.
- Set the state timeout to PFTM_UNLINKED after state has been moved
to the PFSYNC_S_DEL queue in pfsync.
Reported by: Ian FREISLICH <ianf cloudseed.co.za>
share/mk/sys.mk instead.
This is part of a medium term project to permit deterministic builds of
FreeBSD.
Submitted by: Erik Cederstrand <erik@cederstrand.dk>
Reviewed by: imp, toolchain@
Approved by: cperciva
MFC after: 2 weeks
- As the comment report, CALLOUT_LOCAL_ALLOC cannot be checked
directly from the callout flags but might be checked by a cached
value. Hence, do so before to actually remove the callout, when
needed, in softclock_call_cc().
- In softclock_call_cc() also add a comment in the waiting and deferred
migration case explaining that the dereference should be safe
because of the migration dereference invariants.
Additively:
- In softclock_call_cc(), for the deferred migration case, move all the
accesses to callout structure after the comment stating the callout
must not be destroyed.
- For consistency with this last tweak, use cached c_flags for the
KASSERT() in the deferred migration case. It is not strictly necessary
but this way all the callout accesses happen after the above mentioned
comment, improving consistency.
Pointy hat to: me
Sponsored by: Isilon Systems / EMC Corporation
Reviewed by: kib
MFC after: 2 weeks
X-MFC: 243901
lists it reads from its configuration files on the priority field.
Because some items in the lists have the same priority, and std::sort()
is not stable, the exact order in which the items are enumerated does
not have to correspond to the order they appear in the configuration
files.
Apparently this was never noticed with libstdc++, but with libc++ it
could cause the "uhid" entry from /etc/devd/usb.conf to be used instead
of the "ums" entry (which is earlier in the file). This caused the
problem described in the PR: the USB mouse module was never loaded, and
the other actions (such as starting moused) were not executed.
To fix the problem, make devd use std:stable_sort() instead.
Reported by: Jan Beich <jbeich@tormail.org>
PR: bin/172958
MFC after: 2 weeks
to map, and technically this isn't allowed.
Functionally, it works OK (at least on x86) to call bus_dmamap_load with
a NULL data pointer and zero length, so this is primarily for correctness
and consistency with other drivers.
While here, remove check in isci_io_request_construct for nseg==0.
Previously, bus_dmamap_load would pass nseg==1, even for case where
buffer is NULL and length = 0, which allowed CAM_DIR_NONE CCBs
to get processed. This check is not correct though, and needed to be
removed both for the changes elsewhere in this patch, as well as jeff's
preliminary bus_dmamap_load_ccb patch (which uncovered all of this in
the first place).
MFC after: 3 days
- Deembed scope id in L3 address in in6_lltable_dump().
- Simplify scope id recovery in rtsock routines.
- Remove embedded scope id handling in ndp(8) and route(8) completely.
from the callwheel. Calculate the cc->cc_next before removing the
callout, otherwise the code followed the invalid tailq links. After
this, make softclock_call_cc() return void, since it always return
cc->cc_next, which is immediately available to the softclock()
anyway. This also allows to eliminate a label under #ifdef SMP.
Remove the assignment of cc->cc_next from callout_cc_del(), since the
function is called with the callout already removed from callwheel.
If cancelling the migration, also clear the CALLOUT_DFRMIGRATION flag.
Postpone the free of the timeout(9) allocated callouts after the
migration checks are done.
Add some more strict asserts about the state of the callout in
callout_call_cc().
Reviewed by: attilio
Reported and tested by: pho (previous version)
MFC after: 2 weeks
The words "old than" seem to be quoted as "older than" by some sources,
so use the more likely and grammatically correct text.
PR: docs/173868
Submitted by: Chris Petrik <c.petrik.sosa@gmail.com>
Approved by: cperciva
MFC after: 1 week
callout is started before kern_setitimer() acquires process mutex, but
looses a race and kern_setitimer() gets the process mutex before the
callout. Then, assuming that new specified struct itimerval has
it_interval zero, but it_value non-zero, the callout, after it starts
executing again, clears p->p_realtimer.it_value, but kern_setitimer()
already rescheduled the callout.
As the result of the race, both p_realtimer is zero, and the callout
is rescheduled. Then, in the exit1(), the exit code sees that it_value
is zero and does not even try to stop the callout. This allows the
struct proc to be reused and eventually the armed callout is
re-initialized. The consequence is the corrupted callwheel tailq.
Use process mutex to interlock the callout start, which fixes the race.
Reported and tested by: pho
Reviewed by: jhb
MFC after: 2 weeks
- Check V_deembed_scopeid before checking if sa_family == AF_INET6.
- Fix scope id handing in route(8)[2] and ifconfig(8).
Reported by: rpaulo[1], Mateusz Guzik[1], peter[2]
