I have no good explanation why it happens, but I found that in B2B mode
at least Xeon v4 NTB leaks accesses to its configuration memory at BAR0
originated from the link side to its host side. DMAR predictably blocks
those, making access to remote scratchpad registers in B2B mode impossible.
This change creates identity mapping in DMAR covering the BAR0 addresses,
making the NTB work fine with DMAR enabled. It seems like allowing single
4KB range at 32KB offset may be enough, but I don't see a reason to be so
specific.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
PLX NTB sends translated DMA requests not only from itsels, but from all
slots and functions of its bus. By default DMAR blocks those additional.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
Address Lookup Table (A-LUT) being enabled allows to specify separate
translation for each 1/128th or 1/256th of the BAR2. Previously it was
used only to limit effective window size by blocking access through some
of A-LUT elements. This change allows A-LUT elements to also point
different memory locations, providing to upper layers several (up to 128)
independent memory windows. A-LUT hardware allows even more flexible
configurations than this, but NTB KPI have no way to manage that now.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
This restores parity with AMD NTB driver. Though without any drivers
supporting more then one peer and respective KPI modification to pass
peer index to most of the calls this addition is pretty useless now.
MFC after: 2 weeks
This patch is the driver for NTB hardware in AMD SoCs (ported from Linux)
and enables the NTB infrastructure like Doorbells, Scratchpads and Memory
window in AMD SoC. This driver has been validated using ntb_transport and
if_ntb driver already available in FreeBSD.
Submitted by: Rajesh Kumar <rajesh1.kumar@amd.com>
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D18774
This allows replacing "sys/eventfilter.h" includes with "sys/_eventfilter.h"
in other header files (e.g., sys/{bus,conf,cpu}.h) and reduces header
pollution substantially.
EVENTHANDLER_DECLARE and EVENTHANDLER_LIST_DECLAREs were moved out of .c
files into appropriate headers (e.g., sys/proc.h, powernv/opal.h).
As a side effect of reduced header pollution, many .c files and headers no
longer contain needed definitions. The remainder of the patch addresses
adding appropriate includes to fix those files.
LOCK_DEBUG and LOCK_FILE_LINE_ARG are moved to sys/_lock.h, as required by
sys/mutex.h since r326106 (but silently protected by header pollution prior
to this change).
No functional change (intended). Of course, any out of tree modules that
relied on header pollution for sys/eventhandler.h, sys/lock.h, or
sys/mutex.h inclusion need to be fixed. __FreeBSD_version has been bumped.
Its a hack, we can't know/list all DMA engines, but this covers all
I/OAT of Xeon E5/E7 at least from Sandy Bridge till Skylake I saw.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
Remove unused and easy to misuse PNP macro parameter
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
Approved by: re (glen)
I was not aware Warner was making or planning to make forward progress in
this area and have since been informed of that.
It's easy to apply/reapply when churn dies down.
Inspired by r338025, just remove the element size parameter to the
MODULE_PNP_INFO macro entirely. The 'table' parameter is now required to
have correct pointer (or array) type. Since all invocations of the macro
already had this property and the emitted PNP data continues to include the
element size, there is no functional change.
Mostly done with the coccinelle 'spatch' tool:
$ cat modpnpsize0.cocci
@normaltables@
identifier b,c;
expression a,d,e;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,d,
-sizeof(d[0]),
e);
@singletons@
identifier b,c,d;
expression a;
declarer MODULE_PNP_INFO;
@@
MODULE_PNP_INFO(a,b,c,&d,
-sizeof(d),
1);
$ rg -l MODULE_PNP_INFO -- sys | \
xargs spatch --in-place --sp-file modpnpsize0.cocci
(Note that coccinelle invokes diff(1) via a PATH search and expects diff to
tolerate the -B flag, which BSD diff does not. So I had to link gdiff into
PATH as diff to use spatch.)
Tinderbox'd (-DMAKE_JUST_KERNELS).
When enabled by EEPROM, use it to relax translation address/size alignment
requirements for BAR2 window by 128 or 256 times.
MFC after: 1 week
Sponsored by: iXsystems, Inc.
An eventual devd(8) or other component should be able to scan buses and
automatically load drivers that match device ids described in this metadata.
Reviewed by: imp
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12364
There is no big need to burn CPU if other side may be not there yet. For
example, the PLX hardware by default enables the NTB link up on reset, not
dependig on driver to do it. In case of Intel hardware this also reduces
race between MSI-X workaround negotiation and upper layers, using the same
scratchpad registers in different time.
MFC after: 12 days
This driver supports both NTB-to-NTB and NTB-to-Root Port modes (though
the second with predictable complications on hot-plug and reboot events).
I tested it with PEX 8717 and PEX 8733 chips, but expect it should work
with many other compatible ones too. It supports up to two NT bridges
per chip, each of which can have up to 2 64-bit or 4 32-bit memory windows,
6 or 12 scratchpad registers and 16 doorbells. There are also 4 DMA engines
in those chips, but they are not yet supported.
While there, rename Intel NTB driver from generic ntb_hw(4) to more specific
ntb_hw_intel(4), so now it is on par with this new ntb_hw_plx(4) driver and
alike to Linux naming.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Since the doorbell bit is already set when interrupt handler is called,
the event was not propagated to upper layer. It was working normally
because present code was not using masking actively, but that is going
to change.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
New design allows hardware resources to be split between several consumers.
For example, one BAR can be dedicated for remote memory access, while other
resources can be used for packet transport for virtual Ethernet interface.
And even without resource split, this code allows to specify which consumer
driver should attach the hardware.
From some points this makes the code even closer to Linux one, even though
Linux does not provide the described flexibility.
Calling it earlier increases the window when MSIX info may change.
This change does not solve the problem completely, but seems logical.
Complete solution should probably include link reset in case of MSIX
remap to trigger new negotiation, but we have no way to get notified
about that now.
I don't know what errata is mentioned there, I was unable to find it, but
setting limit before the base simply does not work at all. According to
specification attempt to set limit out of the present window range resets
it to zero, effectively disabling it. And that is what I see in practice.
Fixing this properly disables access for remote side to our memory until
respective xlat is negotiated and set. As I see, Linux does the same.
For some reason hack with sending MSI-X interrupts by writing to remote
LAPIC memory works only for 32-bit BARs, that are available only if split
BARs mode is enabled in BIOS. If it is not, complain loudly and fall back
to less efficient workaround.
This allows at least first three doorbells to work very close to normal
hardware, properly signaling events to upper layers without spurious or
lost events. Doorbells above the first three may still report spurious
events due to lack of reliable information, but they are rarely used.
It is odd idea to serialize different MSI-X vectors. Use of rmlocks
here allows them to execute in parallel, but still protects ctx.
If upper layers require any additional serialization -- they can
do it by themselves.
This follows NTB subsystem modularization in Linux, tuning it to FreeBSD
native NewBus interfaces. This change allows to support different types
of hardware with different drivers, support multiple NTB instances in a
system, ntb_transport module use for needs other then if_ntb, etc.
Sponsored by: iXsystems, Inc.
Since SBARxSZ register can be write-once, it can be unusable for disabling
the SBAR. For such case also set SBARxBASE to zero to not intersect with
config BAR.
BAR size to 1MB. According to Xeon v3 specifications and my tests, that
size register is write-once and so not writeable after BIOS written it.
Instead of that, make the code work with BAR of any sufficient size,
properly calculating offset within its base. It also simplifies the code.
Discussed with: cem
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
NTB_MSIX_RECEIVED status, before making upper layers overwrite it.
This is not completely perfect, but now it works better then before.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
