- `b' is now an official alias for `break'. It used to be an unofficial
alias, but this was broken by adding the `bt' alias for `trace'.
- `t' is now an official alias for `trace'. It used to be an unofficial
alias, but this was broken by adding the `thread' command.
- `registers' is now an alias for `show registers'. This is a hack to
break the unofficial `r' alias for `reset'. `r' really means
`registers' in some debuggers, so I sometimes type it accidentally and
am annoyed when it resets the system. A short command shouldn't have
such a large effect. Now at least `res' must be typed to disambiguate
`reset'.
output width of 79, only 6 columns of width 12 each fit, but 7 columns
were printed.
The fix is to pass the width of the next output to db_end_line() and
not assume there that this width is always 1.
Related unfixed bugs:
- 1 character is wasted for a space after the last column
- suppression of trailing spaces used to limit the misformatting, but
seems to have been lost
- in db_examine(), the width of the next output is not know and is
still assumed to be 1.
- Add entries in the uscanner.4 man page (along with missing 3500).
PR: usb/100957 [1], usb/100992 [2]
Submitted by: Jim Teresco <terescoj@teresco.org> [1],
Walter C. Pelissero <walter.pelissero@iesy.net> [2]
MFC after: 3 days
in ip6_output. In case this fails handle the error directly and log it[1].
In addition permit CARP over v6 in ip_fw2.
PR: kern/98622
Similar patch by: suz
Discussed with: glebius [1]
Tested by: Paul.Dekkers surfnet.nl, Philippe.Pegon crc.u-strasbg.fr
MFC after: 3 days
will fix a problem where you boot w/ the default of autoselect, but then
set the speed to 100/full, the switch will keep the autoselect/100/full
negotiation... This will continue to work till someone resets the switch
or unplugs the cable resulting in the switch failing to autoneg and falling
back to 100/half, causing a hard to track down duplex mismatch..
Submitted by: nCircle Network Security, Inc.
MFC after: 1 week
- Add support for the Conexant Waikiki/CX20551-22, found
in most Toshiba P100 series laptops. Despite of growing
urban legend of "unsupported Conexant", this codec is fully
supported in this driver.
Note: Toshiba P100 has broken (acpi) BIOS, thus rendering
its soundchip useless. Please disable ACPI, or get
BIOS updates (if any).
Found/tested by: Vulpes Velox <v.velox@vvelox.net>
URL: http://lists.freebsd.org/pipermail/freebsd-multimedia/2006-September/004896.html
- Parser cleanups to handle possible oss/mixer collision. Found
after parsing Conexant Waikiki nodes.
- Increase resilient against resource failure during attach/detach.
- Implement simple config through hint.pcm.<unit>.config. Supported
options:
gpio0 (default on Acer), gpio1, gpio2, softpcmvol,
fixedrate (default), forcestereo (default)
* Option prefixed with "no" (such as "nofixedrate") will do
the opposite.
* Options can be separated using space " " or comma ",".
* The "no" option will take precedence over anything else.
Example:
hint.pcm.0.config="gpio2,nofixedrate,noforcestereo,nogpio0,softpcmvol"
hint.pcm.0.config="softpcmvol noforcestereo"
read requests to its consumer. It has been developed to address
the problem of a horrible read performance of a 64k blocksize FS
residing on a RAID3 array with 8 data components, where a single
disk component would only get 8k read requests, thus effectively
killing disk performance under high load. Documentation will be
provided later. I'd like to thank Vsevolod Lobko for his bright
ideas, and Pawel Jakub Dawidek for helping me fix the nasty bug.
calls are not used by libthr in RELENG_6 and HEAD, it is only used by
the libthr in RELENG-5, the _umtx_op system call can do more incremental
dirty works than these two system calls without having to introduce new
system calls or throw away old system calls when things are going on.
unsuspecting users.
- Add a comment in NOTES about experimental status of SCHED_ULE.
- Make warning about experimental status in sched_ule(4) a bit
stronger.
Suggested and reviewed by: dougb
Discussed on: developers
MFC after: 3 days
or not the OS has to wait for RX_RDY or TX_RDY to be set before the OS sets
the control code in the control/status register. Looking at the interface
design, it seems that RX_RDY and TX_RDY are probably there to protect
access to the data register and have nothing to do with the control/status
register. Nevertheless, try to take what I think is the more conservative
approach and always wait for the appropriate [TR]X_RDY flag to be set
before writing any of the WR_NEXT, WR_END, RD_START, or RD_NEXT control
codes to the control/status register.
commits. For some reason I thought the scale factor was a shift count
rather than the multiplicand (that is, I thought leal (%eax,%edx,4) was
going to generate %eax + %edx << 4 rather than %eax + %edx * 4). What
I need is to multiply by 16 to convert a real-mode (seg, offset) tuple
into a flat address. However, the max multiplicand for scaled/index
addressing on i386 is 8, so go back to using a shl and an add.
- Convert two more inter-register mov instructions where we don't need to
preserve the source register to xchg instructions to keep our space
savings.
Tested by: Ian FREISLICH if at hetzner.co.za
MFC after: 1 week
