Per the datasheet, the BUSY bit must be set when reading or writing PHY
registers. From Linux commit 80928805babf.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15217
In smsc_phy_init function, when the driver was trying to reset PHY, it
didn't poll for the correct bit (BMCR_RESET) to be cleared. Instead, it
anded it with MII_BMCR (which is 0), so it just exited the loop.
This issue was fixed in Linux in commit d94609200069.
Submitted by: Arshan Khanifar
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Previously, get_keyid() was returning the address of the receive key
instead of the transmit key when renegotiating the transmit key. This
could either hang the card (if a connection was only offloading TLS TX
and thus had a receive key address of -1) or cause the connection to
fail by overwriting the wrong key (if both RX and TX TLS were
offloaded).
Submitted by: Harsh Jain @ Chelsio
Sponsored by: Chelsio Communications
- Microsemi SCSI driver for PQI controllers.
- Found on newer model HP servers.
- Restrict to AMD64 only as per developer request.
The driver provides support for the new generation of PQI controllers
from Microsemi. This driver is the first SCSI driver to implement the PQI
queuing model and it will replace the aacraid driver for Adaptec Series 9
controllers. HARDWARE Controllers supported by the driver include:
HPE Gen10 Smart Array Controller Family
OEM Controllers based on the Microsemi Chipset.
Submitted by: deepak.ukey@microsemi.com
Relnotes: yes
Sponsored by: Microsemi
Differential Revision: https://reviews.freebsd.org/D14514
added/deleted, the delete the multicast addresses previously programmed
in HW and reprogram the new set of multicast addresses.
Submitted by:Vaishali.Kulkarni@cavium.com
MFC after:5 days
device-side (and only device-side) "virtual USB serial adapters" - the
ones you can get with an OTG-capable board - as consoles. It boils down
to adding the device name to kern.console sysctl, although doing that
requires jumping through some hoops. It doesn't change the actual
operation of those virtual devices. The point is to make it possible
for init(8) to recognize them as console devices and to launch getty(8)
for them, when configured as "onifconsole" in ttys(5). The point of
that, in turn, is to add such entries to the default ttys(5), so that
init(8) will launch gettys for device-side "virtual serial adapters",
but not for actual USB serial dongles.
Reviewed by: hselasky@
No objections: imp@
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
We intend to remove support before FreeBSD 12 is branched. These are
available only as 32-bit PCI devices. The driver has an ambiguous
license and I have not been successful in contacting the driver's author
in order to address this.
The planned deprecation has been announced on -current and -stable; if
we receive feedback that the driver is still useful and we are able to
resolve the license issue this deprecation notice can be reverted.
Reviewed by: bapt, brooks, imp, rgrimes
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D15182
This sysctl allows a deeper dive into the sleep abyss comparing to
debug.acpi.suspend_bounce. When the new sysctl is set the system will
execute the suspend sequence up to the call to AcpiEnterSleepState().
That includes saving processor contexts and parking APs. Then, instead
of actually entering the sleep state, the BSP will call resumectx() to
emulate the wakeup. The APs should get restarted by the sequence of
Init and Startup IPIs that BSP sends to them.
MFC after: 8 days
Intel® Arria® 10 SoC.
Cadence Quad SPI Flash is not generic SPI controller, but SPI flash
controller, so don't use spibus here, instead provide quad spi flash
interface.
Since it is not on spibus, then mx25l flash device driver is not usable
here, so provide new n25q flash device driver with quad spi flash
interface.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D10245
When disabling regulator when they are unused, check before is they are
enabled.
While here don't check the enable_cnt on the regulator entry as it is
checked by regnode_stop.
This solve the panic on any board using a fixed regulator that is driven
by a gpio when the regulator is unused.
Tested On: OrangePi One
Pointy Hat to: myself
Reported by: kevans, Milan Obuch (freebsd-arm@dino.sk)
Retrieve the tag from the correct ifnet and use the provided tag
(instead of hardcoded 0xffff, implying no tag) in the routines that
process offload policy.
Submitted by: Krishnamraju Eraparaju @ Chelsio
Sponsored by: Chelsio Communications
that cross this boundary, they perform better when this isn't the
case. Intel uses the 3rd byte in the vendor specific area for
this. The DC P3500 was previously listed without any explanation. Add
the DC P3520 and DC P4500 to the list.
There won't be any others drives needing this quirk. Intel has
standardized a field in the namespace data in 1.3 (noiob). A future
patch will use that if it exists, with fallback to this method.
Submitted by: Keith Busch
Reviewed by: jimharris@
ACPI I/O port descriptors use _MIN and _MAX fields to specify the set
of allowable base (start) addresses for an I/O port resource along with
a _LEN field specifying the length. A fixed resource is supposed to be
encoded with _MIN == _MAX, but some buggy firmwares instead set _MAX to
the end of the fixed range. Relocating I/O ranges only make sense in
_PRS (possible resource settings), not in _CRS (current resource settings),
so if an I/O port range with _MAX set set to the end of the range is
present in _CRS, treat it as a fixed I/O port resource starting at
_MIN.
PR: 224096
Submitted by: Harald Böhm <harald@boehm.codes>
Pointy hat to: jhb (taking so long to actually commit this)
MFC after: 1 week
When ixgbe was converted to iflib, it lost the SIOCGI2C support
that allows ifconfig to print SFP state, optical light levels, etc.
Restore this by plugging in to the ifdi_i2c_req iflib method. Note
that the sanity checking on dev_addr that used to be done in ixgbe is
now done in iflib.
Reviewed by: erj, Matthew Macy <mmacy@mattmacy.io>
Sponsored by: Netflix
Adjust sys/conf/files and sys/modules/puc/Makefile to omit
pucdata.c now tht it's included by puc_pci.c.
Submitted by: Lakhan Shiva Kamireddy (with build fixes by me)
Pull Request: https://github.com/freebsd/freebsd/pull/136
COP allows fine-grained control on whether to offload a TCP connection
using t4_tom, and what settings to apply to a connection selected for
offload. t4_tom must still be loaded and IFCAP_TOE must still be
enabled for full TCP offload to take place on an interface. The
difference is that IFCAP_TOE used to be the only knob and would enable
TOE for all new connections on the inteface, but now the driver will
also consult the COP, if any, before offloading to the hardware TOE.
A policy is a plain text file with any number of rules, one per line.
Each rule has a "match" part consisting of a socket-type (L = listen,
A = active open, P = passive open, D = don't care) and a pcap-filter(7)
expression, and a "settings" part that specifies whether to offload the
connection or not and the parameters to use if so. The general format
of a rule is: [socket-type] expr => settings
Example. See cxgbetool(8) for more information.
[L] ip && port http => offload
[L] port 443 => !offload
[L] port ssh => offload
[P] src net 192.168/16 && dst port ssh => offload !nagle !timestamp cong newreno
[P] dst port ssh => offload !nagle ecn cong tahoe
[P] dst port http => offload
[A] dst port 443 => offload tls
[A] dst net 192.168/16 => offload !timestamp cong highspeed
The driver processes the rules for each new listen, active open, or
passive open and stops at the first match. There is an implicit rule at
the end of every policy that prohibits offload when no rule in the
policy matches:
[D] all => !offload
This is a reworked and expanded version of a patch submitted by
Krishnamraju Eraparaju @ Chelsio.
Sponsored by: Chelsio Communications
While Arcnet has some continued deployment in industrial controls, the
lack of drivers for any of the PCI, USB, or PCIe NICs on the market
suggests such users aren't running FreeBSD.
Evidence in the PR database suggests that the cm(4) driver (our sole
Arcnet NIC) was broken in 5.0 and has not worked since.
PR: 182297
Reviewed by: jhibbits, vangyzen
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15057
The change makes the user and kernel address spaces on i386
independent, giving each almost the full 4G of usable virtual addresses
except for one PDE at top used for trampoline and per-CPU trampoline
stacks, and system structures that must be always mapped, namely IDT,
GDT, common TSS and LDT, and process-private TSS and LDT if allocated.
By using 1:1 mapping for the kernel text and data, it appeared
possible to eliminate assembler part of the locore.S which bootstraps
initial page table and KPTmap. The code is rewritten in C and moved
into the pmap_cold(). The comment in vmparam.h explains the KVA
layout.
There is no PCID mechanism available in protected mode, so each
kernel/user switch forth and back completely flushes the TLB, except
for the trampoline PTD region. The TLB invalidations for userspace
becomes trivial, because IPI handlers switch page tables. On the other
hand, context switches no longer need to reload %cr3.
copyout(9) was rewritten to use vm_fault_quick_hold(). An issue for
new copyout(9) is compatibility with wiring user buffers around sysctl
handlers. This explains two kind of locks for copyout ptes and
accounting of the vslock() calls. The vm_fault_quick_hold() AKA slow
path, is only tried after the 'fast path' failed, which temporary
changes mapping to the userspace and copies the data to/from small
per-cpu buffer in the trampoline. If a page fault occurs during the
copy, it is short-circuit by exception.s to not even reach C code.
The change was motivated by the need to implement the Meltdown
mitigation, but instead of KPTI the full split is done. The i386
architecture already shows the sizing problems, in particular, it is
impossible to link clang and lld with debugging. I expect that the
issues due to the virtual address space limits would only exaggerate
and the split gives more liveness to the platform.
Tested by: pho
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 1 month
Differential revision: https://reviews.freebsd.org/D14633
xdma(4) interface.
This allows us to switch between Altera mSGDMA or SoftDMA engines used by
atse(4) device.
This also makes atse(4) driver become 25% smaller.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9618
SoftDMA is a software implementation of DMA engine built using Altera
FIFO component.
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9620
"Terminus BSD Console" is a derivative of Terminus that is provided
by Mr. Dimitar Zhekov under the 2-clause BSD license for use by the
FreeBSD vt(4) console and other BSDs.
PR: 227409
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Changelist:
- Turn tx_rings and rx_rings arrays into arrays of pointers to kring
structs. This patch includes fixes for ixv, ixl, ix, re, cxgbe, iflib,
vtnet and ptnet drivers to cope with the change.
- Generalize the nm_config() callback to accept a struct containing many
parameters.
- Introduce NKR_FAKERING to support buffers sharing (used for netmap
pipes)
- Improved API for external VALE modules.
- Various bug fixes and improvements to the netmap memory allocator,
including support for externally (userspace) allocated memory.
- Refactoring of netmap pipes: now linked rings share the same netmap
buffers, with a separate set of kring pointers (rhead, rcur, rtail).
Buffer swapping does not need to happen anymore.
- Large refactoring of the control API towards an extensible solution;
the goal is to allow the addition of more commands and extension of
existing ones (with new options) without the need of hacks or the
risk of running out of configuration space.
A new NIOCCTRL ioctl has been added to handle all the requests of the
new control API, which cover all the functionalities so far supported.
The netmap API bumps from 11 to 12 with this patch. Full backward
compatibility is provided for the old control command (NIOCREGIF), by
means of a new netmap_legacy module. Many parts of the old netmap.h
header has now been moved to netmap_legacy.h (included by netmap.h).
Approved by: hrs (mentor)
In UTF-8 locales mandoc uses a number of characters outside of the Basic
Latin group, e.g. from general punctuation or miscellaneous mathematical
symbols, and these rendered as ? in text mode.
This change adds (char, replacement, code point, description):
– - U+2013 En Dash
⟨ < U+27E8 Mathematical Left Angle Bracket
⟩ > U+27E9 Mathematical Right Angle Bracket
This change addresses some common cases; there are others that still
need to be added after a more thorough review.
PR: 227409
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Defines in net/if_media.h remain in case code copied from ifconfig is in
use elsewere (supporting non-existant media type is harmless).
Reviewed by: kib, jhb
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15017
CAM_SEL_TIMEOUT was introduced in
https://reviews.freebsd.org/D7521 (r304251), which claimed:
"VM shall response to CAM layer with CAM_SEL_TIMEOUT to filter those
invalid LUNs. Never use CAM_DEV_NOT_THERE which will block LUN scan
for LUN number higher than 7."
But it turns out this is not correct:
I think what really filters the invalid LUNs in r304251 is that:
before r304251, we could set the CAM_REQ_CMP without checking
vm_srb->srb_status at all:
ccb->ccb_h.status |= CAM_REQ_CMP.
r304251 checks vm_srb->srb_status and sets ccb->ccb_h.status properly,
so the invalid LUNs are filtered.
I changed my code version to r304251 but replaced the CAM_SEL_TIMEOUT
with CAM_DEV_NOT_THERE, and I confirmed the invalid LUNs can also be
filtered, and I successfully hot-added and hot-removed 8 disks to/from
the VM without any issue.
CAM_SEL_TIMEOUT has an unwanted side effect -- see cam_periph_error():
For a selection timeout, we consider all of the LUNs on
the target to be gone. If the status is CAM_DEV_NOT_THERE,
then we only get rid of the device(s) specified by the
path in the original CCB.
This means: for a VM with a valid LUN on 3:0:0:0, when the VM inquires
3:0:0:1 and the host reports 3:0:0:1 doesn't exist and storvsc returns
CAM_SEL_TIMEOUT to the CAM layer, CAM will detech 3:0:0:0 as well: this
is the bug I reported recently:
https://bugs.freebsd.org/bugzilla/show_bug.cgi?id=226583
PR: 226583
Reviewed by: mav
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D14690
Some devices cannot rely on the switch MDIO address passed in the DTB
for specifying single/multi-chip addressing mode. Introduce new property
"single-chip-addressing" which added to DTS will force single-chip mode.
Submitted by: Michal Mazur <mkm@semihalf.com>
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14800
Linux device tree binding, whose usage is obligatory,
comprises faulty representation of Marvell cryptographic
engine (CESA) - two engines are artificially gathered into
single DT node, in order to avoid certain SW limitation.
This patch improves the cesa driver to support above binding,
depending on compatible string, which helps to ensure
backward compatibility.
Submitted by: Patryk Duda
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D14760
The code now has a single, consistant flow for all three ioctl
variants. ifdefs and for pre-FreeBSD-7 compatability are moved to
functions and macros. So the flow is alwasy the same, we impose
the cost of allocating, copying to, updating from, and freeing a
copy of struct pci_conf_io on all paths.
This change will allow PCIOCGETCONF32 support currently in
sys/compat/freebsd32/freebsd32_ioctl.c to be moved here.
Reviewed by: kib, jhb
Obtained from: CheriBSD
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14978
Change OF_getencprop_alloc semantics to be combination of malloc and
OF_getencprop and return size of the property, not number of elements
allocated.
For the use cases where number of elements is preferred introduce
OF_getencprop_alloc_multi helper function that copies semantics
of OF_getencprop_alloc prior to this change.
This is to make OF_getencprop_alloc and OF_getencprop_alloc_multi
function signatures consistent with OF_getencprop_alloc and
OF_getencprop_alloc_multi.
Functionality-wise this patch is mostly rename of OF_getencprop_alloc
to OF_getencprop_alloc_multi except two calls in ofw_bus_setup_iinfo
where 1 was used as a block size.
