updated.
o Number of times NIC ran out of RX buffer descriptors
o Number of inbound packet errors
o Number of inbound packets that were chosen to be discarded
Previously only the discarded packet counter was used to update
if_ierrors. This change fixes wrong if_ierrors counter on
BCM570[0-4] controllers. For BCM5705 and later controllers bge(4)
already correctly counted it.
Reported by: Eugene Grosbein <egrosbein <> rdtc dot ru>
device in device attach. This would help to narrow down issue to a
specific controller and operating mode of the controller.
While I'm here rename BGE_MISCCFG_BOARD_ID with
BGE_MISCCFG_BOARD_ID_MASK.
AMD-8131 PCI-X bridge. The bridge seems to reorder write access to
mailbox registers such that it caused watchdog timeouts by
out-of-order TX completions.
Tested by: Michael L. Squires <mikes <> siralan dot org >
Reviewed by: jhb
- Pass interrupt trapframe for handlers dow the chain
- Add PMC interrupt handler
PMC interrupt is a special case, so we want handle it as soon as possible
with minimum overhead. So we handle it apb filter routine.
bootable image.
The kernel has to fit inside an 896KiB area in a 4MB SPI flash.
So a bunch of stuff can't be included (and more is to come), including
(unfortunately) IPv6.
TODO:
* GPIO modules need to be created
* Shrink the image a bit more by removing some of the CAM layer debugging
strings.
When ntp switched between PLL and FLL mode it produced a log message
"kernel time sync status change %04x". This issue is reported in ntp
bug 452[1] which claims that this behaviour is normal and the log
message isn't necessary. I'm not sure exactly when it was removed, but
it's gone in the latest ntp release (4.2.6p5).
[1] http://bugs.ntp.org/show_bug.cgi?id=452
Approved by: roberto
While there, make some style adjustments, like missed () around
return values.
Submitted by: bde
Reviewed by: mckusick
Tested by: pho
MFC after: 2 weeks
The bawrite() schedules the write to happen immediately, and its use
frees the current thread to do more cleanups.
Submitted by: bde
Reviewed by: mckusick
Tested by: pho
MFC after: 2 weeks
Synchronous inode block update is not needed for MNT_LAZY callers (syncer),
and since waitfor values are not zero, code did unneccessary synchronous
update.
Submitted by: bde
Reviewed by: mckusick
Tested by: pho
MFC after: 2 weeks
call preinit, init and fini arrays methods from crt1 for static binaries.
Mark new crt1 with FreeBSD-specific ELF note.
Move some common crt1 code into new MI file ignore_init.c, to reduce
duplication. Also, conservatively adjust nearby sources for style.
Reviewed by: kan
Tested by: andrew (arm), flo (sparc64)
MFC after: 3 weeks
particular on ARM, do require working init arrays.
Traditional FreeBSD crt1 calls _init and _fini of the binary, instead
of allowing runtime linker to arrange the calls. This was probably
done to have the same crt code serve both statically and dynamically
linked binaries. Since ABI mandates that first is called preinit
array functions, then init, and then init array functions, the init
have to be called from rtld now.
To provide binary compatibility to old FreeBSD crt1, which calls _init
itself, rtld only calls intializers and finalizers for main binary if
binary has a note indicating that new crt was used for linking. Add
parsing of ELF notes to rtld, and cache p_osrel value since we parsed
it anyway.
The patch is inspired by init_array support for DragonflyBSD, written
by John Marino.
Reviewed by: kan
Tested by: andrew (arm, previous version), flo (sparc64, previous version)
MFC after: 3 weeks
PCP and CFI fields.
* Ethernet_type for VLAN encapsulation is tunable, default is 0x8100;
* PCP (Priority code point) and CFI (canonical format indicator) is
tunable per VID;
* Tunable encapsulation to support 802.1q
* Encapsulation/Decapsulation code improvements
New messages have been added for this netgraph node to support the
new features.
However, the legacy "vlan" id is still supported and compiled in by
default. It can be disabled in a future release.
TODO:
* Documentation
* Examples
PR: kern/161908
Submitted by: Ivan <rozhuk.im@gmail.com>
- add the macro NETMAP_RING_FIRST_RESERVED() which returns
the index of the first non-released buffer in the ring
(this is useful for code that retains buffers for some time
instead of processing them immediately)
quantum bytewise to the address of a 64-bit variable results in writing
to the "wrong" 32-bit half so adjust the address accordingly. This fix
is implemented in a hackish way for two reasons:
o in order to be able to get it into 8.3 with zero impact on the little-
endian architectures where this bug has no effect and
o to avoid blowing the x86 boot2 out of the water again when compiling
it with clang, which all sane versions of this fix tested do.
This change fixes booting from UFS1 file systems on big-endian machines.
MFC after: 3 days
make use of it where possible.
This primarily brings in support for newer hardware, and FreeBSD is not yet
able to support the abundance of IRQs on new hardware and many features in the
Ethernet driver.
Because of the changes to IRQs in the Simple Executive, we have to maintain our
own list of Octeon IRQs now, which probably can be pared-down and be specific
to the CIU interrupt unit soon, and when other interrupt mechanisms are added
they can maintain their own definitions.
Remove unmasking of interrupts from within the UART device now that the
function used is no longer present in the Simple Executive. The unmasking
seems to have been gratuitous as this is more properly handled by the buses
above the UART device, and seems to work on that basis.
of the Cavium Simple Executive, which violates large function growth rules
in such a way that simply increasing the large function growth parameter is
insufficient.
o) The MAC set must occur before the multicast list is set up as the former
will enable the CAM unconditionally, while promiscuous mode disables it,
so if promiscuous mode is to be set this must occur after the MAC is
programmed.
o) The multicast list must be set up unconditionally as even if flags have
not changed, if the interface has gone through a reinitialization, the
state of the CAM as changed by the MAC initialization could be incorrect.
o) Call octm_init when flags change, even if the interface is already running.
kernel version introduced the sysctl (based upon a linux man-page)
- add comments to sscalls.master regarding some names of sysctls which are
different than the linux-names (based upon the linux unistd.h)
- add some dummy sysctls
- name an unimplemented sysctl
MFC after: 1 month
Lower (ISA) IRQs are working, but allowed mask is not set correctly.
Block both by default to allow HP BL465c G6 blade system to boot.
Reported by: Attila Nagy <bra@fsn.hu>
MFC after: 1 week
Although access to the flags to check/set OACTIVE is racy due to how
the default if_start() function works, this should remove any races
with read/modify/write between threads.
don't setup the avp mcast queue.
This is a bit annoying though - it turns out the mcast queue isn't
initialised for STA mode but it's then touched to see whether anything
is in it. That should be fixed in a subsequent commit.
Noticed by: gperez@entel.upc.edu
PR: kern/165895
Instead of using 25MHz equality threshold, look for the nearest value when
handling dev.cpu.0.freq sysctl and for exact match when it is expected.
ACPI may report extra level with frequency 1MHz above the nominal to
control Intel Turbo Boost operation. It is not a bug, but feature:
dev.cpu.0.freq_levels: 2934/106000 2933/95000 2800/82000 ...
In this case value 2933 means 2.93GHz, but 2934 means 3.2-3.6GHz.
I've found that my Core i7-870 based system has Intel Turbo Boost disabled
by default and without this change it was absolutely invisible and hard
to control.
MFC after: 2 weeks
After 8.0-RELEASE, iwi(4) doesn't send any data frames in infrastructure
mode.
Bacause of the condition `while (frm < efrm)', IEEE80211_VERIFY_LENGTH()
was checking item length beyond the ieee80211_frame region, and returned
from iwi_checkforqos() without setting flags, capinfo and associd.
In infrastructure mode associd is required, so this problem causes
discarding mbuf in ieee80211_start().
PR: kern/165819
Tested/Reviewed/Supported by: bschmidt and adrian
MFC after: 1 week
- Pass number of events to the statclock() and profclock() functions
same as to hardclock() before to not call them many times in a loop.
- Rename them into statclock_cnt() and profclock_cnt().
- Turn statclock() and profclock() into compatibility wrappers,
still needed for arm.
- Rename hardclock_anycpu() into hardclock_cnt() for unification.
MFC after: 1 week
- Remove unneeded whitespace for function calls.
- Add empty line at the top of functions without local variables.
- Change while (1) to for (;;).
MFC after: 1 week
socket is used. The previous code structure assumed that AF_INET sockets
were always available, which is an invalid assumption on IPv6-only systems.
This merges the fololowing revisions from NetBSD:
src/usr.bin/ftp/main.c 1.120
src/usr.bin/ftp/util.c 1.156
PR: bin/162661
Tested by: bz
Obtained from: NetBSD
MFC after: 1 week
