(1) Merged i386/i386/sb.h, deleted pc98/pc98/sb.h.
(2) pc98/conf/GENERIC8 looks more like i386/conf/GENERIC now.
(3) Fixed display bug in pc98/boot/biosboot/io.c.
(4) Prepare to merge memory allocation routines:
pc98/i386/locore.s
pc98/i386/machdep.c
pc98/pc98/pc98_machdep.c
pc98/pc98/pc98_machdep.h
(5) Support new board "C-NET(98)":
pc98/pc98/if_ed98.h
pc98/pc98/if_ed.c
(6) Make sure FPU is recognized for non-Intel CPUs:
pc98/pc98/npx.c
(7) Do not expect bss to be zero-allocated:
pc98/pc98/pc98.c
Submitted by: The FreeBSD(98) Development Team
I586_OPTIMIZED_BCOPY is configured.
Similarly for bzero/I586_OPTIMIZED_BZERO.
Fake 586's had better have a hardware FPU with non-broken exception
handling (we mask exceptions, but broken exception handling may trap
on the instructions that do the masking). I guess this means that
the routines won't work on most 386's or FPUless 486's even when they
have a h/w FPU.
These are based on using the FPU to do 64-bit stores. They also
use i586-optimized instruction ordering, i586-optimized cache
management and a couple of other tricks. They should work on any
i*86 with a h/w FPU, but are slower on at least i386's and i486's.
They come close to saturating the memory bus on i586's. bzero()
can maintain a 3-3-3-3 burst cycle to 66 MHz non-EDO main memory
on a P133 (but is too slow to keep up with a 2-2-2-2 burst cycle
for EDO - someone with EDO should fix this). bcopy() is several
cycles short of keeping up with a 3-3-3-3 cycle for writing. For
a P133 writing to 66 MHz main memory, it just manages an N-3-3-3,
3-3-3-3 pair of burst cycles, where N is typically 6.
The new routines are not used by default. They are always configured
and can be enabled at runtime using a debugger or an lkm to change
their function pointer, or at compile time using new options (see
another log message).
Removed old, dead i586_bzero() and i686_bzero(). Read-before-write is
usually bad for i586's. It doubles the memory traffic unless the data
is already cached, and data is (or should be) very rarely cached for
large bzero()s (the system should prefer uncached pages for cleaning),
and the amount of data handled by small bzero()s is relatively small
in the kernel.
Improved comments about overlapping copies.
Removed unused #include.
I have only tested the ABP5140 card and only with a single CDROM drive
but it seems to work fine. This driver relies on features found only in
the SCSI branch so will not work in -current until those changes
are brought in. It also doesn't have any error handling code *yet*.
The goal is to use this driver as the development platform for the new
generic SCSI layer error recovery/handling code.
PCI and EISA front ends will show up as soon as I get my hands on
the cards. There are also a few issues in the driver that I need
to clear up with AdvanSys before I can suggest sticking one of
these cards in your server. 8-)
Thanks to AdvanSys for releasing this code under a suitable copyright.
Obtained from: Ported from the Linux driver writen by
bobf@advansys.com (Bob Frey).
[long long] results when I last worked on them, but they are normally
used together with to daddr_t's and off_t's which are signed, so the
unsigned results did little except cause warnings.
The main change is from unsigned long unsigned int. It just needs to
be a 32-bit type and unsigned int is most natural. Using a non-long
type has the "advantage" of hiding bugs in the "machine-independent"
code where it prints foo_t's using %d or %x. These bugs are currently
hidden bug not compiling with -Wformat.
I tried changing vm_ooffset_t from long long to unsigned long long, but
that was wrong because vm_ooffset_t needs to be long to match off_t,
although file offsets are never negative.
Reviewed by: dyson
Staticized it in userconfig. The one in pcvt is unused.
Removed bogus unused arg to getchar(). This should not have compiled
in the USERCONFIG_BOOT case, but the getchar() was also non-prototyped
and defined in K&R style.
Staticized the badly named global variable `next'. Even static variables
should have a unique module-specific prefix so that they can be referenced
easily in debuggers, etc.
First, change sysinstall and the Makefile rules to not build the kernel
nlist directly into sysinstall now. Instead, spit it out as an ascii
file in /stand and parse it from sysinstall later. This solves the chicken-n-
egg problem of building sysinstall into the fsimage before BOOTMFS is built
and can have its symbols extracted. Now we generate the symbol file in
release.8.
Second, add Poul-Henning's USERCONFIG_BOOT changes. These have two
effects:
1. Userconfig is always entered, rather than only after a -c
(don't scream yet, it's not as bad as it sounds).
2. Userconfig reads a message string which can optionally be
written just past the boot blocks. This string "preloads"
the userconfig input buffer and is parsed as user input.
If the first command is not "USERCONFIG", userconfig will
treat this as an implied "quit" (which is why you don't need
to scream - you never even know you went through userconfig
and back out again if you don't specifically ask for it),
otherwise it will read and execute the following commands
until a "quit" is seen or the end is reached, in which case
the normal userconfig command prompt will then be presented.
How to create your own startup sequences, using any boot.flp image
from the next snap forward (not yet, but soon):
% dd of=/dev/rfd0 seek=1 bs=512 count=1 conv=sync <<WAKKA_WAKKA_DOO
USERCONFIG
irq ed0 10
iomem ed0 0xcc000
disable ed1
quit
WAKKA_WAKKA_DOO
Third, add an intro screen to UserConfig so that users aren't just thrown
into this strange screen if userconfig is auto-launched. The default
boot.flp startup sequence is now, in fact, this:
USERCONFIG
intro
visual
(Since visual never returns, we don't need a following "quit").
Submitted-By: phk & jkh
divisor latch registers if the registers wouldn't change.
Use the default console cfcr setting while setting the divisor
latch registers for console i/o. Input may be messed up by
transiently changing the cfcr.
Use a usual cfcr setting while setting the divisor latch registers
in the probe. This shouldn't matter, but this is not the place to
test the UART's handling of 5 bit words.
Removed a stale devfs comment.
was always disabled because "pci.h" wasn't included. Now the configured
pci devices are listed and you can edit bogus flags for them.
Fixed bitrot in the disabled code. A used #include was removed and const
poisoning wasn't fixed.
Removed unused #include.
dependent operation, and not really a correct name. invltlb and invlpg
are more descriptive, and in the case of invlpg, a real opcode.
Additionally, fix the tlb management code for 386 machines.
for headers in the compile directory work unsurprisingly. Without
-I-, the search for "foo.h" begins in the directory of the file
that includes it, and the compile directory is only searched because
`-I.' is in ${INCLUDES}.
Removed -I$S/sys from ${INCLUDES}. It was once necessary to find
things like "param.h" in $S/sys. Now <sys/param.h> is found in $S.
lcall 7,0 (ie: ldt slot 0) and lcall 0x87,0 (ldt slot 16, it's shifted
three bits to the left). I was fiddling with this so long ago, I don't
recall the specifics.
with this quite a while ago when somebody reported a BSD/OS 2.1 binary
that wouldn't run. I'm pretty sure they tried it and I'm pretty sure
they mentioned to me that the patch worked.
comparisons in the inb() and outb() macros. I decided that int args
are OK here. Any type that can hold a u_int16_t without overflow
is correct, and 32-bit types are optimal.
Introduced a few tens of warnings (100 in LINT) for use of pessimized
(short) types for the port arg. Only a few drivers are affected by
this. u_short pessimizations aren't detected.
Added `__extension__' before the statement-expression in inb() so
that it can be compiled without warnings by gcc -pedantic.
- don't include <sys/ioctl.h> in any header. Include <sys/ioccom.h>
instead. This was already done in 4.4Lite for the most important
ioctl headers. Header spam currently increases kernel build
times by 10-20%. There are more than 30000 #includes (not counting
duplicates) for compiling LINT.
- include <sys/types.h> if and only it is necessary to make the header
almost self-sufficient (some ioctl headers still need structs from
elsewhere).
- uniformized idempotency ifdefs. Copied the style in the 4.4Lite
ioctl headers.
It is needed for implementation details but very little of it is
needed for the interface. Include it in the few places that didn't
already include it.
Include <sys/ioccom.h> in <sys/disklabel.h> (as already in
<sys/diskslice.h>) so that all the disk-related headers are almost
self-sufficient.
the prototype.
Put the jump table for i486_bzero() in the data section. This
speeds up i486_bzero() a little on Pentiums without significantly
affecting its speed on 486's.
Don't waste time falling through 14 nop's to return from do1 in
i486_bzero().
Use fastmove() for counts >= 1024 (was > 1024). Cosmetic.
Fixed profiling of fastmove().
Restored meaningful labels from the pre-1.1 version in fastmove().
Local labels are evil.
Fixed (high resolution non-) profiling of __bb_init_func().
I maintain that it saves more power to simply "hlt" the CPU than to
spend tons of time trying to tell the APM bios to do the same.
In particular if you do it 100 times a second...
Saved a few bytes by copying `dosdev' and/or `name' to local variables.
This optimization (for dosdev) was done in one place before but this
was lost in the devread() cleanup. This optimization (for dosdev)
can almost be done by bogusly declaring dosdev as const, but gcc still
often space-pessimizes code like the following:
extern const int dosdev; ... foo(dosdev); bar(dosdev);
gcc often doesn't bother to copy dosdev to a temporary local because
the local would have to be preserved in memory across the call to
foo(). OTOH, for
extern int dosdev; ... auto int dosdev_copy = dosdev; ...
foo(dosdev_copy); bar(dosdev_copy);
the copy must be made because foo() might alter dosdev.
the pointer to the string "/kernel". This pointer was once only
statically to once save space, but it has had to be dynamically
initialized for some time, so the static initialization just wastes
space. The string gets moved to the text section, so the actual
savings may be negative due to padding.
instead of 0 if there is no input.
pcvt_drv.c:
Partially fixed pccncheckc(). It returned a boolean value instead of
the character that it fetches from the input fifo (if any). I think
it still discards characters after the first for multi-char input.
instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
still being used just to support printing of the device name in the
probe. Restored the method used in rev.1.6 and changed it to print
the same strings as the previous revision.
Reviewed by: Paul Richards
(1) Add PC98 support to apm_bios.h and ns16550.h, remove pc98/pc98/ic
(2) Move PC98 specific code out of cpufunc.h (to pc98.h)
(3) Let the boot subtrees look more alike
Submitted by: The FreeBSD(98) Development Team
<freebsd98-hackers@jp.freebsd.org>
modified. Pages that are removed by the pageout daemon were
the worst affected. Additionally, numerous minor cleanups,
including better handling of busy page table pages. This
commit fixes the worst of the pmap problems recently introduced.
biosextmem > 65536, but biosextmem is a 16-bit quantity so it is
guaranteed to be < 65536. Related cruft for biosbasemem was
mostly cleaned up in rev.1.26.
It worked because it is spelled correctly in LINT.
Added old obscure syscons options MAXCONS, SLOW_VGA and XT_KEYBOARD.
This file should be sorted both alphabetically and on the module
name by using a consistent prefix for each module, but there is no
consistency in the old options. E.g., MAXCONS is spelled PCVT_NSCREENS
for pcvt.
and xdm, possibly in general.
What was happening was that the server was doing a tcsetattr(.. TCSADRAIN)
on the mouse fd after a write. Since /dev/sysmouse had a null t_oproc,
the drain failed with EIO. Somehow this spammed XFree86 (!@&^#%*& binary
release!!), and the driver was left in a bogus state (ie: switch_in_progress
permanently TRUE).
The simplest way out was to implement a dummy scmousestart() routine to
accept any characters from the tty system and toss them into the void.
It would probably be more correct to intercept scwrite()'s to the mouse
device, but that's executed for every single write to the screen.
Supplying a start routine to eat the characters is only executed for the
mouse port during startup/shutdown, so it should be faster.
-I- to CFLAGS. <sb.h> must currently be used to give the version
of sb.h in the current directory, while "sb.h" in the buggy version
gave the (wrong) version in the source directory. Searching in the
source directory first is normal, but is the reverse of the order
suggested by the 4.4Lite2 #include style. -I- will remove the
ambiguities.
This enables other consumers of the mouse, to get it info via
moused/syscons.
In order to use it run moused (from sysconfig), and then tell
your Xserver that it should use /dev/sysmouse (mknod sysmouse c 12 128)
and it a mousesystems mouse. Everybody will be happy then :)
Remember that moused still needs to know what kind of mouse you
have..
Comments welcome, as is test results...
The default level works with minimal overhead, but one can also enable
full, efficient use of a 512K cache. (Parameters can be generated
to support arbitrary cache sizes also.)
(A pointer to a const was misused to avoid loading loading the same
value twice, but gcc does exactly the same optimization automatically.
It can see that the value hasn't changed.)
- avoiding strcmp("?" saved 12 bytes. gcc inlined the strcmp()
but this takes as much or more code as a function call. The
inlining was bogus because the strcmp() in the bootstrap isn't
standard.
- using a char instead of an int for the boolean `last_only' saved 8
bytes. Booleans should usually be represented as chars on the i386.
- simplifying the return tests saved 9 bytes.
- using putc instead of printf to print a newline saved 3 bytes of code
and 2 bytes of const data.
- avoiding `else's by always doing the else clause and fixing it up
saved 4+8 bytes.
gcc always generates large code for accesses to globals. For locals
it only generates large code if there are more than 128 bytes of
locals. It sorts scalar locals after array locals to pessimize for
space in the usual case when there are more (static) references to
scalars than to arrays.
Saved another 16 bytes (13 before padding) by adding a `continue'.
Fall-through tests normally save space, but here one of them made
gcc do space-unoptimal register allocation (it allocates ch in %bl
because preserving this register across function calls is "free",
but comparisions with %bl take one byte fewer than comparsions with
%bl).
If you define this, it means your keyboard is actually probable using the
brain-dammaged probe routine in syscons, and if the keyboard is NOT found,
then you don't want syscons to activate itself further.
This makes life sane for those of us who use serial consoles most of the
time and want "the right thing" to happen when we plug a keyboard in.
I just couldn't get the code to be as small as it should have gotten..
atill a LITTLE bigger than before as I need to allow the
default string to have options as well
1/ Makefile: the maximum size for boot2 is 7.5K not 7K,
so don't complain until it reaches THAT size..
newfs leaves 8K and boot 1 is 512k. leaving 7.5K becasue the disklabel
is considered to part of the boot2 file.
[512 boot1][512 disklabel][ 7K boot2 code ]
[boot1 file][ boot2 file ]
2/ Boot2.S: move the soring of the default name read from block 2 to AFTER
clearing the BSS.
3/ boot.c:
Move the parsing of the command line into the
place it's called for clarity.. alsoi comment it a bit and clean it
up a bit.. for some reason this seems ot have made it a little
larger, but I can't work out why.. maybe bruce might have ideas?
compensated for by shrinkage elsewhere..
the practical result of this is htat the default string can now contain args
e.g. if you change the default string to have -gd
then the machine will boot to the dgb debugger stub by default..
this is mostly useful with the nextboot utility..
as it now allows you to remotely force a machine to reboot into
the debugger.
(1) Remove mk30line (moved to /usr/sbin, but not in our source tree yet)
(2) Delete unneeded (well, harmful now :) code to prohibit #including
of isa_device.h from PC98 sources.
(3) Remove files now equal to their ISA/PC-AT counterparts.
Submitted by: The FreeBSD(98) Development Team
so that the compiler can see that it is OK to use const strings in
NDINIT(). Some emulators want to use paths of the form "/compat/foo".
Removed the casts that hid the non-problem. Didn't fix the missing
consts in syscalls.master that hid the non-problem.
returned by the RTC, use the bootblock supplied value. Also, map the
'stolen by BIOS' memory in the same manner as the ISA-hole memory, since
it is really an extenstion of the BIOS. This is necessary for 32-bit
BIOS functions such as APM support on laptops, and the loss of memory
for non-necessary functions seems to be at most 4k.
Reviewed by: phk
Obtained from: email conversation with jtk@atria.com
during phk's staticize/cleanup commits. pstat needs it, the MAXCONS
option is not visible anywhere else, and pstat uses it to find the bounds
of the sccons[MAXCONS] array, which varies.
. preserve a multi-char sequence in a small static buffer inside
pccngetc(), so it won't be clobbered later (used to happen when
breaking into DDB user Ctrl-Alt-ESC), and
. simplify the ``keystroke is present'' determination in sgetc(), thus
making pccncheck() actually working without waiting for a keystroke.
for work regardless of whether there was an interrupt. This needs more
work, it should be able to run better when there are more than 3 host
cards present, ie: all cards in polling-only mode with no IRQ. (The
host cards have a choice of 3 irq's, 11, 12, or 15, or just polling)
little more reliably. So far I've received a couple of positive
responses and no objections to these changes.
There are two one-line changes:
- In wdprobe(), when testing the error status of drives, don't
unconditionally decide that there is no controller present if we
read back a value of 0x81 (drive 0 okay, drive 1 failed) twice
in a row. This may be caused by having an ATAPI CD-ROM jumpered
as a master on the controller with no slave.
- In wdgetctlr(), when checking for a status of WDCS_READY, check the
value twice. The first time may be bogus. This stops a phantom wd2
device from being detected when an ATAPI CD-ROM is attached to the
secondary controller alone as a slave. (This can cause installation to
fail when sysinstall attempts to open the phantom device and wedges the
system as a result. This has bitten me a couple of times on some
Gateway 2000 machines.)
. make pccncheck() work even when interrupts are disabled, so the
``Press a key on the console...'' procedure will work,
. make kernel colors #ifndef, so they can be overridden from the
config file,
. use shutdown_nice() instead of cpu_reset() if Ctrl-Alt-Del is
enabled,
. allow pccngetc() to return more than a single character, so the
arrow keys will work (and thus visual UserConfig!),
. fix a warning.
This closes all know PRs related to pcvt, in particular #845, #1236,
and #1265. PR #991 is a duplicate for 845, and PR #1283 has already
been fixed earlier in rev 1.11 of pcvt_conf.h.
Submitted by: Ulf Kieber (kieber@sax.de), for the kernel color fix
nearest .01 Mhz rather than simply truncating it downwards.
This hack makes this 89.999928 Mhz clock correctly round to the closer
90.00-MHz rather than 89.99-MHz:
> i586 clock: 89999928 Hz, i8254 clock: 1193152 Hz
> CPU: Pentium (90.00-MHz 586-class CPU)
buffer in certain error conditions. Sync up the code to that in NetBSD
where applicable.
Reviewed by: Gary Jennejohn <garyj@munich.netsurf.de>
Submitted by: Michael Smith <msmith@atrad.adelaide.edu.au>
Obtained from: NetBSD sources
Changed i586_ctr_bias from long long to u_int. Only the low 32 bits
are used now that microtime uses a multiplication to do the scaling.
Previously the high 32 bits had to match those of rdtsc() to prevent
overflow traps and invalid timeval adjustments.
early enough when the dump device is specified in the config file.
Removed stale comment about configuration root and swap devices.
Don't bother clearing dumplo when dumpdev is set to NODEV. Everything
is controlled by dumpdev.
Fixed the kern.dumpdev sysctl. Writes were handle bogusly.
problem with the 'shell scripts' was found, but there was a 'strange'
problem found with a 486 laptop that we could not find. This commit
backs the code back to 25-jul, and will be re-entered after the snapshot
in smaller (more easily tested) chunks.
and then never accept for sending packet from upper layer anymore
(i.e. ping -f )
Reviewed by: David Greenman <dg@root.com>
Submitted by: amurai@spec.co.jp
performance issues.
1) The pmap module has had too many inlines, and so the
object file is simply bigger than it needs to be.
Some common code is also merged into subroutines.
2) Removal of some *evil* PHYS_TO_VM_PAGE macro calls.
Unfortunately, a few have needed to be added also.
The removal caused the need for more vm_page_lookups.
I added lookup hints to minimize the need for the
page table lookup operations.
3) Removal of some bogus performance improvements, that
mostly made the code more complex (tracking individual
page table page updates unnecessarily). Those improvements
actually hurt 386 processors perf (not that people who
worry about perf use 386 processors anymore :-)).
4) Changed pv queue manipulations/structures to be TAILQ's.
5) The pv queue code has had some performance problems since
day one. Some significant scalability issues are resolved
by threading the pv entries from the pmap AND the physical
address instead of just the physical address. This makes
certain pmap operations run much faster. This does
not affect most micro-benchmarks, but should help loaded system
performance *significantly*. DG helped and came up with most
of the solution for this one.
6) Most if not all pmap bit operations follow the pattern:
pmap_test_bit();
pmap_clear_bit();
That made for twice the necessary pv list traversal. The
pmap interface now supports only pmap_tc_bit type operations:
pmap_[test/clear]_modified, pmap_[test/clear]_referenced.
Additionally, the modified routine now takes a vm_page_t arg
instead of a phys address. This eliminates a PHYS_TO_VM_PAGE
operation.
7) Several rewrites of routines that contain redundant code to
use common routines, so that there is a greater likelihood of
keeping the cache footprint smaller.
blocked in a write() while waiting for the output to drain, sleep only
for tp->t_timeout, not forever. This only seems to happen when there is
either a modem lockup holding the hardware flow control down, or due to
some problem in the driver with processes attempting to write after the
modem has hung up (eg: elm, tf).
Saves about 280 butes of source per driver, 56 bytes in object size
and another 56 bytes moves from data to bss.
No functional change intended nor expected.
GENERIC should be about one k smaller now :-)
#ifdef DIAGNOSTIC case, and a warning only otherwise.
People who want them to break into the debugger can always set the
breakpoint explicitly. The existing behaviour was a misfeature from
the beginning, in the (wrong) assumption that the SCSI controller must
always be of essential importance to the entire system.
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
of this patch, which had not actually been reviewed by Joerg or Paul!
(I'll better stop committing files after midnight ...)
I'm now commiting the latest code, which has been reported to work.
Minor correction to the previous commit message for this file:
The first PCI Lance in a system will get a name of lnc1, the second
will be known as lnc2 and so on. An arbitrary number of cards is
supported in a system ...
before attaching. Without this fix, 3c579(EISA) never make
any H/W inturrupt.
Reviewed by: "Justin T. Gibbs" <gibbs@freefall.freebsd.org>, nao@sbl.cl.nec.co.jp and owner-current on mailing list ;-)
Submitted by: amurai@spec.co.jp, nao@sbl.cl.nec.co.jp
This code applies to several systems with integrated Ethernet
chip, for example from HP or Compaq. It should also support
PCI Ethernet cards based on the AMD PCI Lance chip.
This code has been reviewed (visually) by Paul Richards and
tested (using an ISA Lance board) by Joerg Wunsch.
Since the parameters to nearly each and every single function
had to be changed (generally from unit number to lnc_soft*),
there is some potential for buglets having crept in ...
BEWARE: If you had lnc0 configured to have the ISA probe find
your PCI Lance, then it should now be found by the PCI probe,
and should be automatically configured as pci1 (!!! note the "1").
Reviewed by: paul, joerg
(author's explaination):
Bit 15 is the flag to request a transmit complete interrupt. The
driver was apparently written to minimize interrupts, and if not for a
3-COM design quirk, everything would be just ducky.
Prior to loading the outbound packet into the FIFO, the driver checks
to see if there's enough space to contain the packet. If not, the
driver requests a transmit-available interrupt when there is
sufficient room. Unfortunately, the card is continuing to process the
prior FIFO, and by the time the driver sets the threshold for a
transmit available interrupt, the space is already available. When
this occurs, the 3COM card ignores the interrupt request, and the
driver is hung waiting for an interrupt that will never occur.
There's probably a more elegant solution, but requesting the transmit
complete interrupt was the easiest to implement. An alternative fix
might be to check free FIFO space again, after requesting the transmit
available interrupt, but I haven't bothered pursuing this. Since the
patch, my 3C590 (PCI, same FIFO interface as 3C509) has been rock
solid.
Submitted by: mevans@candle.com (Mike Evans)
