1. ICMP ECHO and TSTAMP replies are now rate limited.
2. RSTs generated due to packets sent to open and unopen ports
are now limited by seperate counters.
3. Each rate limiting queue now has its own description, as
follows:
Limiting icmp unreach response from 439 to 200 packets per second
Limiting closed port RST response from 283 to 200 packets per second
Limiting open port RST response from 18724 to 200 packets per second
Limiting icmp ping response from 211 to 200 packets per second
Limiting icmp tstamp response from 394 to 200 packets per second
Submitted by: Mike Silbersack <silby@silby.com>
the kernel console. Instead, change logwakeup() to set a flag in the
softc. A callout then wakes up every so often and wakes up any processes
selecting on /dev/log (such as syslogd) if the flag is set. By default
this callout fires 5 times a second, but that can be adjusted by the
sysctl kern.log_wakeups_per_second.
Reviewed by: phk
Add detach routine and turn driver into a module so it can be loaded
and unloaded. Also take a stab at implementing multicast packet
reception so that this NIC will work with IPv6. Promiscuous mode
doesn't seem to work, but I'm not sure why. It works well enough that
I can run dhclient on it and put it on the office network though.
Also ripped out spl stuff and replaced it with mutexes.
Looking in src/Makfile* it looks like all the "WANT_AOUT" support
has been removed, maybe these should just go away...
Note that the a.out `ld' reaches over into src/contrib/gcc for libiberty
bits. This is biting us because the libiberty bits have evolved beyond
what the a.out `ld' can handle.
This change fixes the broken world, but only because very few have
"WANT_AOUT" defined.
This is a driver for the LanMedia/SBE LMC150x E1/T1 family of cards.
The driver currently support unframed E1 (2048kbit/s) and framed
E1 (nx64).
These cards will provision E1/T1 lines for about 1/4 the cost of
a cisco router...
a SIGINFO (normally via Ctrl-T), a line will be output indicating
the current phase number and progress information relevant to the
current phase.
Approved by: mckusick
commands have also been slightly updated as follows:
- Use ktr_idx to find the newest entry rather than walking the buffer
comparing timespecs. Timespecs are not always unique after the change
to use getnanotime(9).
- Add a new verbose setting. When the verbose setting is on, then the
timestamp is printed with each message. If KTR_EXTEND is on, then the
filename and line number are output as well. By default this option is
off. It can be turned on with the 'v' modifier passed to the 'tbuf'
and 'tall' commands. For the 'tnext' command, the 'v' modifier toggles
the verbose mode.
- Only display the cpu number for each message on SMP systems.
- Don't display anything for an empty entry that hasn't been used yet.
MS will be treated as having this quirk. In the event that we falsely
identify one that doesn't need it, no harm will be done. Ken
suggested that we make this more generic since there may be more
needed in the future.
Reported by: TERAMOTO Masahiro <teramoto@comm.eng.osaka-u.ac.jp>
PR: kern/23378
Reviewed by: ken
server on 11-July-2000, at 17:32 Zulu.
This is the last point [that I know of] that Cygnus synced their internal
IA-64 GCC tree with the public FSF one.
- IP addresses are verified as being correct dotted quad format.
- Netmasks are verified as being in correct dotted quad or 0x* format,
and being consecutive 1 bits followed by consecutive 0 bits.
- The gateway is verified as being correct dotted quad format and
being reachable through the configured IP address and netmask.
no as a default. Sysinstall should be both less dangerous and less
annoying as a result of this change, though that's just my opinion
(since they're the defaults which annoy ME the least :).
present questinos with a different default answer. Somebody submitted
a patch to me once which did something this but I lost it (my bad) so
I'm just going to re-implement it with thanks to whomever it was who
gave me the idea.