rl(4) driver and put it in a new re(4) driver. The re(4) driver shares
the if_rlreg.h file with rl(4) but is a separate module. (Ultimately
I may change this. For now, it's convenient.)
rl(4) has been modified so that it will never attach to an 8139C+
chip, leaving it to re(4) instead. Only re(4) has the PCI IDs to
match the 8169/8169S/8110S gigE chips. if_re.c contains the same
basic code that was originally bolted onto if_rl.c, with the
following updates:
- Added support for jumbo frames. Currently, there seems to be
a limit of approximately 6200 bytes for jumbo frames on transmit.
(This was determined via experimentation.) The 8169S/8110S chips
apparently are limited to 7.5K frames on transmit. This may require
some more work, though the framework to handle jumbo frames on RX
is in place: the re_rxeof() routine will gather up frames than span
multiple 2K clusters into a single mbuf list.
- Fixed bug in re_txeof(): if we reap some of the TX buffers,
but there are still some pending, re-arm the timer before exiting
re_txeof() so that another timeout interrupt will be generated, just
in case re_start() doesn't do it for us.
- Handle the 'link state changed' interrupt
- Fix a detach bug. If re(4) is loaded as a module, and you do
tcpdump -i re0, then you do 'kldunload if_re,' the system will
panic after a few seconds. This happens because ether_ifdetach()
ends up calling the BPF detach code, which notices the interface
is in promiscuous mode and tries to switch promisc mode off while
detaching the BPF listner. This ultimately results in a call
to re_ioctl() (due to SIOCSIFFLAGS), which in turn calls re_init()
to handle the IFF_PROMISC flag change. Unfortunately, calling re_init()
here turns the chip back on and restarts the 1-second timeout loop
that drives re_tick(). By the time the timeout fires, if_re.ko
has been unloaded, which results in a call to invalid code and
blows up the system.
To fix this, I cleared the IFF_UP flag before calling ether_ifdetach(),
which stops the ioctl routine from trying to reset the chip.
- Modified comments in re_rxeof() relating to the difference in
RX descriptor status bit layout between the 8139C+ and the gigE
chips. The layout is different because the frame length field
was expanded from 12 bits to 13, and they got rid of one of the
status bits to make room.
- Add diagnostic code (re_diag()) to test for the case where a user
has installed a broken 32-bit 8169 PCI NIC in a 64-bit slot. Some
NICs have the REQ64# and ACK64# lines connected even though the
board is 32-bit only (in this case, they should be pulled high).
This fools the chip into doing 64-bit DMA transfers even though
there is no 64-bit data path. To detect this, re_diag() puts the
chip into digital loopback mode and sets the receiver to promiscuous
mode, then initiates a single 64-byte packet transmission. The
frame is echoed back to the host, and if the frame contents are
intact, we know DMA is working correctly, otherwise we complain
loudly on the console and abort the device attach. (At the moment,
I don't know of any way to work around the problem other than
physically modifying the board, so until/unless I can think of a
software workaround, this will have do to.)
- Created re(4) man page
- Modified rlphy.c to allow re(4) to attach as well as rl(4).
Note that this code works for the sample 8169/Marvell 88E1000 NIC
that I have, but probably won't work for the 8169S/8110S chips.
RealTek has sent me some sample NICs, but they haven't arrived yet.
I will probably need to add an rlgphy driver to handle the on-board
PHY in the 8169S/8110S (it needs special DSP initialization).
FIDs to be 128-bits wide and adds support for realms.
Add a new CODA_COMPAT_5 option, which requests support for the old
Coda 5.x interface instead of the new one.
Create a new coda5.ko module that supports the 5.x interface, and make
the existing coda.ko module use the new 6.x interface. These modules
cannot both be loaded at the same time.
Obtained from: Jan Harkes & the coda-6.0.2 distribution,
NetBSD (drochner) (CODA_COMPAT_5 option).
of what uart(4) is and/or is not see the initial commit log of one
of the files in sys/dev/uart (or see share/man/man4/uart.4).
Note that currently pc98 shares the MD file with i386. This needs
to change when pc98 support is fleshed-out to properly support the
various UARTs. A good example is sparc64 in this respect.
We build uart(4) as a module on all platforms. This may break
the ppc port. That depends on whether they do actually build
modules.
To use uart(4) on alpha, one must use the NO_SIO option.
change also disables interrupts around non-S4 suspends whereas before we
did not do this. Our version of AcpiEnterSleepStateS4bios was almost
identical to the ACPICA version.
support stripped out and minimally renamed to owi. This driver
attaches to lucent cards only. This is designed to aid in the testing
of fixes to the wi driver for lucent cards. It is supported only as a
module (you cannot compile it into your kernel). You cannot have the
wi driver in your kernel (or loaded as a moudle) to use the owi
module.
I've not connected it to build, as this module is currently for
debugging purposes. This is for developers only at the present time.
If we can't get lucent support fixed by 5.2 code freeze, then we'll
re-evaulate this support level. Please use this to fix the lucent
support in dev/wi. This will be removed from the system when lucent
support has been fixed in dev/wi.
Note to developers: Do not connect this to the build, make it possible
to build into the kernel or otherwise 'integrate' this into system
without checking with me first. This is for debugging purposes only.
If this doesn't work for you, I don't want to hear about it unless you
are fixing the wi driver :-)
found only many tv-cards.
We currently use more ore less evil hacks (slow_msp_audio sysctl) to
configure the various variants of these chips in order to have
stereo autodetection work. Nevertheless, this doesn't always work
even though it _should_, according to the specs.
This is, for example, the case for some popular Hauppauge models sold
sold in Germany.
However, the Linux driver always worked for me and others. Looking at
the sourcecode you will find that the linux-driver uses a very much
enhanced approach to program the various msp34xx chipset variants,
which is also found in the specs for these chips.
This is a port of the Linux MSP34xx code, written by Gerd Knorr
<kraxel@bytesex.org>, who agreed to re-release his code under a
BSD license for this port.
A new config option "BKTR_NEW_MSP34XX_DRIVER" is added, which is required
to enable the new driver. Otherwise the old code is used.
The msp34xx.c file is diff-reduced to the linux-driver to make later
modifications easier, thus it doesn't follow style(9) in most cases.
Approved by: roger (committing this, no time to test/review),
keichii (code review)
it attaches to all existing NATM network interfaces in the system
and creates a HARP physical interface for each of them. This allows
us to use the same set of ATM drivers for all ATM stuff. It is
possible to use the same interface for HARP, NATM and netgraph at the
same time.
with a ProATM-155 and an IDT evaluation board and should also work
with a ProATM-25 (it seems to work at least, I cannot really measure
what the card emits). The driver has been tested on i386 and sparc64,
but should work an other archs also. It supports UBR, CBR, ABR and VBR;
AAL0, AAL5 and AALraw. As an additional feature VCI/VPI 0/0 can be
opened for receiving in AALraw mode and receives all cells not claimed
by other open VCs (even cells with invalid GFC, VPI and VCI fields and
OAM cells).
Thanks to Christian Bucari from ProSum for lending two cards and answering
my questions.
large to huge amounts of small or medium sized receive buffers. The problem
with these situations is that they eat up the available DMA address space
very quickly when using mbufs or even mbuf clusters. Additionally this
facility provides a direct mapping between 32-bit integers and these buffers.
This is needed for devices originally designed for 32-bit systems. Ususally
the virtual address of the buffer is used as a handle to find the buffer as
soon as it is returned by the card. This does not work for 64-bit machines
and hence this mapping is needed.
ACPI nodes with the plug and play ID's defined for a "Generic ISA Bus
Device" as defined in section 10.7 of the ACPI 2.0 specification. This
gives machines like the Libretto that contain a fake ISA bus that is not
connected via a PCI-ISA bridge an ISA bus for ISA devices to attach to.
Tested by: markm
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
build it on the i386 and alpha architectures, where this has been
set up (there is also a sparc64-bitops.h in sys/gnu/ext2fs, but it
appears to be broken and it is not linked up).
This should unbreak the sparc64 LINT build.
built by LINT. Also override a number of knobs for enabling and
disabling various modules in the ALL_MODULES case to further increase
LINT's module coverage.
Submitted by: ru
redundant paths to the same device.
This class reacts to a label in the first sector of the device,
which is created the following way:
# "0123456789abcdef012345..."
# "<----magic-----><-id-...>
echo "GEOM::FOX someid" | dd of=/dev/da0 conv=sync
NB: Since the fact that multiple disk devices are in fact the same
device is not known to GEOM, the geom taste/spoil process cannot
fully catch all corner cases and this module can therefore be
confused if you do the right wrong things.
NB: The disk level drivers need to do the right thing for this to
be useful, and that is not by definition currently the case.
on friday 13th and without making a universe). This adds struct and
constant definitions for ATM traffic parameters and re-enables the
build of the midway driver.
Tested by: make universe
