interfaces to be a vlan (IFT_L2VLAN) rather than an Ethernet interface
(IFT_ETHER). The code already fixed if_type in the ifnet causing some
places to report the interface as a vlan (e.g. arp -a output) and other
places to report the interface as Ethernet (getifaddrs(3)). Now they
should all report IFT_L2VLAN.
Reviewed by: brooks
MFC after: 1 month
use a different interface type (IFT_L2VLAN vs IFT_ETHER). Treat IFT_L2VLAN
interfaces like IFT_ETHER interfaces when handling link layer addresses.
Reviewed by: syrinx (bsnmpd)
MFC after: 1 week
the virtualization detection successfully disabling the clflush instruction.
This fixes insta-panics for XEN hvm users when the hw.clflush_disable
tunable is -1 or 0 (-1 by default).
Discussed with: jhb
cdev will never be destroyed. Propagate the flag to devfs vnodes as
VV_ETERNVALDEV. Use the flags to avoid acquiring devmtx and taking a
thread reference on such nodes.
In collaboration with: pho
MFC after: 1 month
MIPS doesn't really need to use atomic_cmpset_int() in situations like
this because the software dirty bit emulation in trap.c acquires
the pmap lock. Atomics like this appear to be a carryover from i386
where the hardware-managed TLB might concurrently set the modified bit.
Reviewed by: alc
pmap_page_wired_mappings() counts the number of pv entries for the
specified page that have the pv entry wired flag set to TRUE.
pmap_enter() correctly initializes this flag. However,
pmap_change_wiring() doesn't update the corresponding pv entry flag,
only the PTE. So, the count returned by pmap_page_wired_mappings()
will sometimes be wrong.
In the short term, the best fix would be to eliminate the pv entry
flag and use only the PTE. That flag is wasting non-trivial memory.
Remove pv_wired flag, and use PTE flag to count the wired mappings.
Reviewed by: alc
value resulted in poor performance for UDP packets. With this
change, UDP bulk transfer performance is more than 940Mbps.
While I'm here fix a wrong register definition.
- Load added resources.
- Stop and forget removed resources.
- Update modified resources in least intrusive way, ie. don't touch
/dev/hast/<name> unless path to local component or provider name were
modified.
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 1 month
- Don't exit on errors if not requested.
- Don't keep configuration in global variable, but allocate memory for
configuration.
- Call yyrestart() before yyparse() so that on error in configuration file
we will start from the begining next time and not from the place we left of.
MFC after: 1 month
VM86 calls instead of the real mode emulator as a backend. VM86 has been
proven reliable for very long time and it is actually few times faster than
emulation. Increase maximum number of page table entries per VM86 context
from 3 to 8 pages. It was (ridiculously) low and insufficient for new VM86
backend, which shares one context globally. Slighly rearrange and clean up
the emulator backend to accommodate new code. The only visible change here
is stack size, which is decreased from 64K to 4K bytes to sync. with VM86.
Actually, it seems there is no need for big stack in real mode.
MFC after: 1 month
PJDLOG_ASSERT() and PJDLOG_VERIFY() that will check the given condition
and log the problem where appropriate. The difference between those
two is that PJDLOG_VERIFY() always work and PJDLOG_ASSERT() can be
turned off by defining NDEBUG.
MFC after: 1 month
As des noted, the section on SCTP would benefit from
a rewrite by a native speaker (which I am not).
Any volunteers?
Approved by: des (mentor)
MFC after: 1 week
bus_generic_resume() since the pci_link(4) driver was added.
- Change the ACPI PCI-PCI bridge driver to inherit most of its methods
from the generic PCI-PCI bridge driver. In particular, this will now
restore PCI config registers for ACPI PCI-PCI bridges.
Tested by: Oleg Sharoyko osharoiko of gmail
changes to the package database, i.e. any packages that
have been added, updated or deleted in the past 24 hours.
The format is intentionally simple and concise.
That information is particularly useful on servers that
are maintained by multiple administrators. When someone
adds, updates or deletes a package, the others will see
it in the daily periodic output.
This script is disabled by default.
PR: conf/113913
Submitted by: olli
Approved by: des (mentor)
MFC after: 3 weeks
