so they were disabled during DTS transition. Though there are
no standard devices/drivers on them people might use iic(4) userland
interface to access these buses.
Originally it was added in order to prevent trashing of objects with
INVARIANTS enabled. The same effect is now provided with mere UMA_ZONE_NOFREE.
This reverts r286921.
Discussed with: kib
Objects obtained from such zones are supposed to retain type stability,
which was violated by aforementioned trashing.
This is a follow-up to r284861.
Discussed with: kib
broke in two ways. One, the pacing variable was accessed in multiple
threads in an unsafe way. Two, since large numbers of I/O could come
down from the buf layer at one time, large numbers of allocation
failures could happen all at once, resulting in a huge pace value that
would limit I/Os to 10 IOPS for minutes (or even hours) at a
time. While a real solution to these problems requires substantial
work (to go to a no-allocation after the first model, or to have some
way to wait for more memory with some kind of reserve for pager and
swapper requests), it is relatively easy to make this simplistic
pacing less pathological.
Move to using a volatile variable with loads and stores. While this is
a little racy, losing the race is safe: either you get memory and
proceed, or you don't and queue. Second, sleep for 1ms (or one tick, whichever
is larger) instead of 100ms. This removes the artificial 10 IOPS limit
while still easing up on new I/Os during memory shortages. Remove
tying the amount of time we do this to the number of failed requests
and do it only as long as we keep failing requests.
Finally, to avoid needless recursion when memory is tight (start ->
g_io_deliver() -> g_io_request() -> start -> ... until we use 1/2 the
stack), don't do direct dispatch while pacing. This should be a rare
event (not steady state) so the performance hit here is worth the
extra safety of not starving g_down() with directly dispatched I/O.
Differential Review: https://reviews.freebsd.org/D3546
the buffer. (n == hostlen) also means the buffer length was
too short.
- Use sdl->sdl_data only when (sdl->sdl_nlen > 0 && sdl->sdl_alen == 0)
to prevent redundant output.
Resetting some generations of the I/OAT hardware (just BDXDE for now)
resets the corresponding MSI-X registers. So, teardown and
re-initialize interrupts after resetting the hardware.
Reviewed by: jimharris
Approved by: markj (mentor)
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3549
a one word variable, which is quite unexpected from documentation.
So, to avoid double installation of a single kernel, protect the extra
kernels loop with ${BUILDKERNELS:[#]} > 1 conditional.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
go asking what debug flags to set for GEOM to make it work. Advice
them to use gpart(8) instead.
Something similar should probably done with disklabel,
but I need to rewrite the disklabel examples first.
Reviewed by: wblock@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3315
o In pccard_ether add code to start children of a 802.11
device, that are configured in rc.conf.
o In devd.conf provide a regex matching all 802.11 devices,
and on match run pccard_ether to spawn children.
PR: 202784
Submitted by: <vidwer gmail.com>
In collaboration with: "Oleg V. Nauman" <oleg opentransfer.com>
and exit events. procfs stop events for system call tracing report these
values (argument count for system call entry and code for system call exit),
but ptrace() does not provide this information. (Note that while the system
call code can be determined in an ABI-specific manner during system call
entry, it is not generally available during system call exit.)
The values are exported via new fields at the end of struct ptrace_lwpinfo
available via PT_LWPINFO.
Reviewed by: kib
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3536
If net.link.bridge.pfil_bridge is set we can end up thinking we're forwarding in
pf_test6() because the rcvif and the ifp (output interface) are different.
In that case we're bridging though, and the rcvif the the bridge member on which
the packet was received and ifp is the bridge itself.
If we'd set dir to PF_FWD we'd end up calling ip6_forward() which is incorrect.
Instead check if the rcvif is a member of the ifp bridge. (In other words, the
if_bridge is the ifp's softc). If that's the case we're not forwarding but
bridging.
PR: 202351
Reviewed by: eri
Differential Revision: https://reviews.freebsd.org/D3534
SoC is used in the HiKey board from 96boards.
Currently on the SD card is working on the HiKey, as such devices 0 and 2
will need to be disabled, for example by adding the following to
loader.conf:
hint.hisi_dwmmc.0.disabled=1
hint.hisi_dwmmc.2.disabled=1
Relnotes: yes (Hikey board booting)
Sponsored by: ABT Systems Ltd
on the Variant II code, however arm64 uses Variant I. The former placed the
thread pointer after the data, pointing at the thread control block, while
the latter places these before said data.
Because of this we need to use the size of the previous entry to calculate
where to place the current entry. We also need to reserve 16 bytes at the
start for the thread control block.
This also fixes the value of TLS_TCB_SIZE to be correct. This is the size
of two unsigned longs, i.e. 2 * 8 bytes.
While here remove the bogus adjustment of the pointer in the
R_AARCH64_TLS_TPREL64 case. It should be the offset of the data relative
to the thread pointer, including the thread control block.
Sponsored by: ABT Systems Ltd
have TLS program header. This is needed on architectures with Variant I
tls, that is arm, arm64, mips, and powerpc. These place the thread control
block at the start of the buffer and, without this, this data may be
trashed.
This appears to not be an issue on mips or powerpc as they include a second
adjustment to move the thread local data, however this is on arm64 (with a
future change to fix placing this data), and should be on arm. I am unable
to trigger this on arm, even after changing the code to move the data
around to make it more likely to be hit. This is most likely because my
tests didn't use the variable in offset 0.
Reviewed by: kib
MFC after: 1 week
Sponsored by: ABT Systems Ltd
builds, and prepend it to SNAPSHOT_DATE to prevent a trailing '-'
in the final box name for a release build.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
particular, this invalidates the knote kn_link linkage, making the
SLIST_FOREACH() loop accessing undefined values (e.g. trashed by
QUEUE_MACRO_DEBUG). If the knote is freed by other thread when kq
lock is released or when influx is cleared, e.g. by knote_scan() for
kqueue owning the knote, the iteration step would access freed memory.
Use SLIST_FOREACH_SAFE() to fix iteration.
Diagnosed by: avg
Tested by: avg, lstewart, pawel
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Explain why it is fine to not check for M_NOWAIT failures in
kqueue_register(). Remove unneeded check for NULL result from
waitable allocation in kqueue_scan(). uma_free(9) handles NULL
argument correctly, remove checks for NULL. Remove useless cast and
adjust style in knote_alloc().
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
of the D_NEWBLK kinds of dependencies (i.e. D_ALLOCDIRECT and
D_ALLOCINDIR), which can exhaust kmem.
Handle excess of D_NEWBLK in the same way as excess of D_INODEDEP and
D_DIRREM, by scheduling ast to flush dependencies, after the thread,
which created new dep, left the VFS/FFS innards. For D_NEWBLK, the
only way to get rid of them is to do full sync, since items are
attached to data blocks of arbitrary vnodes. The check for D_NEWBLK
excess in softdep_ast_cleanup_proc() is unlocked.
For 32bit arches, reduce the total amount of allowed dependencies by
two. It could be considered increasing the limit for 64 bit platforms
with direct maps.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Connect it to the build.
The code assumed that SCHED_* constants form a contiguous set of
numbers, remove the assumption by using schedulers[] array in
get_different_scheduler(). This is no-op on FreeBSD, but improves
code portability.
The selection of different priority used the min/max priority range of
the current scheduler class, instead of the priority to be changed to.
The bug caused the test failure.
Remove duplication of POSIX_SPAWN_SETSIGDEF flag and now unused
duplications of MIN/MAX definitions.
Reviewed by: jilles, pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D3533
from BUILDKERNELS list. This is more strict, since INSTALLKERNEL by
definition is the first word of BUILDKERNELS list. The previous
code failed if INSTALLKERNEL is a substring of additional kernel name.
Reviewed by: gjb
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
