be the same chip):
- The I/O port resource may not be available with these. However, given
that we actually only need this resource for some controllers that
require their firmware to be up- and downloaded (which excludes the
SAS1078{,DE}) just handle failure to allocate this resource gracefully
when possible. While at it, generally put non-fatal resource allocation
failures under bootverbose.
- SAS1078{,DE} use a different hard reset protocol.
- Add workarounds for the 36GB physical address limitation of scatter/
gather elements of these controllers.
Tested by: Slawa Olhovchenkov
PR: 149220 (remaining part)
on extended and extensible structs if_msghdrl and ifa_msghdrl. This
will allow us to extend both the msghdrl structs and eventually if_data
in the future without breaking the ABI.
Bump __FreeBSD_version to allow ports to more easily detect the new API.
Reviewed by: glebius, brooks
MFC after: 3 days
both 64bit and 32bit binaries, not for 64bit only.
The set of the flag is not neccessary there, because the only current
user of the cpu_set_user_tls() is create_thread(), which calls
cpu_set_upcall() before and cpu_set_upcall() itself sets PCB_FULL_IRET.
Change the function for consistency and preserve existing KPI for now.
MFC after: 1 week
Code should just use the devtoname() function to obtain the name of a
character device. Also add const keywords to pieces of code that need it
to build properly.
MFC after: 2 weeks
overridden at attach time.
Some 802.11n NICs may only have one physical antenna connected.
The radios will be very upset if you try enabling radios which aren't
connected to antennas.
This allows hints to override the TX and RX chainmask.
These hints are:
hint.ath.X.rx_chainmask
hint.ath.X.tx_chainmask
They can be set at either boot time or in kenv before the module is loaded.
This and the previous HAL commit were sponsored in late 2011 by Hobnob, Inc.
Sponsored by: Hobnob, Inc.
by capabilities.
Add an ar5416SetCapability() function, which contains logic to override
the chainmask and update the relevant stream.
This is designed to be called after the attach function, which presets
the TX/RX chainmask and stream.
TODO: check the chainmask against the hardware chainmask so non-existing
chains aren't enabled.
If an IPv6 packet has extension headers the kernel needs to deal with it
itself. For the rest it can set various CSUM_XXX flags and the driver
will act on them.
the kernel allocated a buffer but did not zero it as it was about
to be completely filled by a uiomove() from the user's buffer.
However, if the uiomove() failed, the old contents of the buffer
could be exposed especially if the file was being mmap'ed. The
fix was to always zero the buffer when it was allocated.
This change first attempts the uiomove() to the newly allocated
(and dirty) buffer and only zeros it if the uiomove() fails. The
effect is to eliminate the gratuitous zeroing of the buffer in
the usual case where the uiomove() successfully fills it.
Reviewed by: kib
Tested by: scottl
MFC after: 2 weeks (to 9 only)
Reading register $29 with RDHWR is becoming the de-facto standard to
implement TLS. According to linux-mips wiki, MIPS Technologies has
reserved hardware register $29 for ABI use. Furthermore current GCC
makes the following assumptions:
- RDHWR is natively available or otherwise emulated by the kernel
- Register $29 holds the TLS pointer
Submitted by: Robert Millan <rmh@debian.org>
with clang. Also fix a number of warnings uncovered when building with
clang around some implicit enum conversions.
Sponsored by: Intel
Approved by: scottl
A new jail(8) option "devfs_ruleset" defines the ruleset enforcement for
mounting devfs inside jails. A value of -1 disables mounting devfs in
jails, a value of zero means no restrictions. Nested jails can only
have mounting devfs disabled or inherit parent's enforcement as jails are
not allowed to view or manipulate devfs(8) rules.
Utilizes new functions introduced in r231265.
Reviewed by: jamie
MFC after: 1 month
Add support for updating the devfs mount (currently only changing the
ruleset number is supported).
Check mnt_optnew with vfs_filteropt(9).
This new option sets the specified ruleset number as the active ruleset
of the new devfs mount and applies all its rules at mount time. If the
specified ruleset doesn't exist, a new empty ruleset is created.
MFC after: 1 month
1. Fixed timeout specification for the msleep in mps_wait_command().
Added 30 second timeout for mps_wait_command() calls in mps_user.c.
2. Make sure we call mps_detach_user() from the kldunload path.
3. Raid Hotplug behavior change.
The driver now removes a volume when it goes to a failed state,
so we also need to add volume back to the OS when it goes to
opitimal/degraded/online from failed/missing.
Handle raid volume add and remove from the IR_Volume event.
4. Added some more debugging information.
5. Replace xpt_async(AC_LOST_DEVICE, path, NULL) with
mpssas_rescan_target().
This is to work around a panic in CAM that shows up when adding a
drive with a rescan and removing another device from the driver thread
with an AC_LOST_DEVICE async notification.
This problem was encountered in testing with the LSI sas2ircu utility,
which was used to create a RAID volume from physical disks. The driver
has to create the RAID volume target and remove the physical disk
targets, and triggered a panic in the process.
The CAM issue needs to be fully diagnosed and fixed, but this works
around the issue for now.
6. Fix some memory initialization issues in mps_free_command().
7. Resolve the "devq freeze forever" issue. This was caused by the
internal read capacity command issued in the non-head version of the
driver. When the command completed with an error, the driver wasn't
unfreezing thd device queue.
The version in head uses the CAM infrastructure for getting the read
capacity information, and therefore doesn't have the same issue.
8. Bump the version to 13.00.00.00-fbsd. (this is very close to LSI's
internal stable driver 13.00.00.00)
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
MFC after: 3 days
TUNABLE variable (hw.netmap.buf_size) so we can experiment
with values different from 2048 which may give better cache performance.
- rearrange the memory allocation code so it will be easier
to replace it with a different implementation. The current code
relies on a single large contiguous chunk of memory obtained through
contigmalloc.
The new implementation (not committed yet) uses multiple
smaller chunks which are easier to fit in a fragmented address
space.
ext4 but that can be used in ext3 mode.
Also adjust the internal inode to carry the birthtime,
like in UFS, which is starting to get some use when
big inodes are available.
Right now these are just placeholders for features
to come.
Approved by: jhb (mentor)
MFC after: 2 weeks
- Increase probing order for ECDT table to match HID-based probing.
- Decrease probing order for HPET table to match HID-based probing.
- Decrease probing order for CPUs and system resources.
- Fix ACPI_DEV_BASE_ORDER to reflect the reality.
every 30 seconds. This spike in I/O caused the system to pause every
30 seconds which was quite annoying. So, the way that sync worked
was changed so that when a vnode was first dirtied, it was put on
a 30-second cleaning queue (see the syncer_workitem_pending queues
in kern/vfs_subr.c). If the file has not been written or deleted
after 30 seconds, the syncer pushes it out. As the syncer runs once
per second, dirty files are trickled out slowly over the 30-second
period instead of all at once by a call to sync(2).
The one drawback to this is that it does not cover the filesystem
metadata. To handle the metadata, vfs_allocate_syncvnode() is called
to create a "filesystem syncer vnode" at mount time which cycles
around the cleaning queue being sync'ed every 30 seconds. In the
original design, the only things it would sync for UFS were the
filesystem metadata: inode blocks, cylinder group bitmaps, and the
superblock (e.g., by VOP_FSYNC'ing devvp, the device vnode from
which the filesystem is mounted).
Somewhere in its path to integration with FreeBSD the flushing of
the filesystem syncer vnode got changed to sync every vnode associated
with the filesystem. The result of this change is to return to the
old filesystem-wide flush every 30-seconds behavior and makes the
whole 30-second delay per vnode useless.
This change goes back to the originally intended trickle out sync
behavior. Key to ensuring that all the intended semantics are
preserved (e.g., that all inode updates get flushed within a bounded
period of time) is that all inode modifications get pushed to their
corresponding inode blocks so that the metadata flush by the
filesystem syncer vnode gets them to the disk in a timely way.
Thanks to Konstantin Belousov (kib@) for doing the audit and commit
-r231122 which ensures that all of these updates are being made.
Reviewed by: kib
Tested by: scottl
MFC after: 2 weeks
a credential structure would corrupt it. This happened when the
p argument was != NULL. However, I now realize that the copying of
open credentials should only happen for p == NULL, since that indicates
that it is a read-ahead or write-behind. This patch fixes this.
After this commit, r228827 could be reverted, but I think the code is
clearer and safer with the patch, so I am going to leave it in.
Without this patch, it was possible that a NFSv4 VOP_SETATTR() could have
changed the credentials of the caller. This would have happened if
the process doing the VOP_SETATTR() did not have the file open, but
some other process running as a different uid had the file open for writing
at the same time.
MFC after: 5 days
guarantee that all UFS inode metadata changes results in the dirtiness
of the inodeblock. Due to missed inodeblock updates, syncer was
required to fsync each mount point' vnode to guarantee periodic
metadata flush.
Reviewed by: mckusick
Tested by: scottl
MFC after: 2 weeks
radar parameters for the AR5416 and later NICs.
These parameters have been tested on the following NICs:
* AR5416
* AR9160
* AR9220
* AR9280
And yes, these will return radar pulse parameters and (for AR9160 and later)
radar FFT information as PHY errors.
This is again not enough to do radar detection, it's just here to faciliate
development and validation of radar detection algorithms.
The (pulse, not FFT) decoding code for AR5212, AR5416 and later NICs exist
in the HAL.
This code is disabled for now as generating radar PHY errors can quickly
cause issues in busy environment.s Some further debugging of the RX path
is needed.
Finally, these parameters are likely not useful for the AR5212 era NICs.
The madwifi-dfs branch should have suitable example parameters for the
11a era NICs.
list. If softdep_sync_buf() discovers such dependency, it should do
nothing, which is safe as it is only waiting on the parent buffer to
be written, so it can be removed.
Committed on behalf of: jeff
MFC after: 1 week
mnt_noasync counter to temporary remove MNTK_ASYNC mount option, which
is needed to guarantee a synchronous completion of the initiated i/o
before syscall or VOP return. Global removal of MNTK_ASYNC option is
harmful because not only i/o started from corresponding thread becomes
synchronous, but all i/o is synchronous on the filesystem which is
initiated during sync(2) or syncer activity.
Instead of removing MNTK_ASYNC from mnt_kern_flag, provide a local
thread flag to disable async i/o for current thread only. Use the
opportunity to move DOINGASYNC() macro into sys/vnode.h and
consistently use it through places which tested for MNTK_ASYNC.
Some testing demonstrated 60-70% improvements in run time for the
metadata-intensive operations on async-mounted UFS volumes, but still
with great deviation due to other reasons.
Reviewed by: mckusick
Tested by: scottl
MFC after: 2 weeks
TCP_KEEPCNT, that allow to control initial timeout, idle time, idle
re-send interval and idle send count on a per-socket basis.
Reviewed by: andre, bz, lstewart
to fix it (without fixing it), after making one of my servers unbootable,
after now making also my laptop unbootable and after running out of patiance
back out r229800 until better solution is found.
set on the new thread. This prevents the thread from inadvertently
inheriting affinity from a random sibling.
Submitted by: attilio
Tested by: pho
MFC after: 1 week
kernel modules that include binary-only code.
More fine-grained control is provided via MK_SOURCELESS_HOST (for native code
that runs on host CPU) and MK_SOURCELESS_UCODE (for microcode).
Reviewed by: julian, delphij, freebsd-arch
Approved by: kib (mentor)
MFC after: 2 weeks
in r179783 as (ab)using the concept of VRFs for this had not worked.
At this point SCTP in FreeBSD does not support multi-FIB, neither for
IPv4 nor for IPv6.
Discussed with: rrs
Sponsored by: Cisco Systems, Inc.
Try to make the "rtable" handling work but the current version of
pf(4) does not fully support it yet as especially callers of
PF_MISMATCHAW() are not fully FIB-aware. OpenBSD seems to have
fixed this in a later version. Prepare as much as possible.
Sponsored by: Cisco Systems, Inc.
the original IPv4 implementation from r178888:
- Use RT_DEFAULT_FIB in the IPv4 implementation where noticed.
- Use rt*fib() KPI with explicit RT_DEFAULT_FIB where applicable in
the NFS code.
- Use the new in6_rt* KPI in TCP, gif(4), and the IPv6 network stack
where applicable.
- Split in6_rtqtimo() and in6_mtutimo() as done in IPv4 and equally
prevent multiple initializations of callouts in in6_inithead().
- Use wrapper functions where needed to preserve the current KPI to
ease MFCs. Use BURN_BRIDGES to indicate expected future cleanup.
- Fix (related) comments (both technical or style).
- Convert to rtinit() where applicable and only use custom loops where
currently not possible otherwise.
- Multicast group, most neighbor discovery address actions and faith(4)
are locked to the default FIB. Individual IPv6 addresses will only
appear in the default FIB, however redirect information and prefixes
of connected subnets are automatically propagated to all FIBs by
default (mimicking IPv4 behavior as closely as possible).
Sponsored by: Cisco Systems, Inc.
the (maximum) number of FIBs trying to clarify that evetually FIBs
should probably attached to domain(9) specific storage. [1]
Add a comment on a limitimation on the rt_add_addr_allfibs option.
Use RT_DEFAULT_FIB instead of 0 where applicable.
Add empty line to functions without local variables per style.
Put public yet unused in-tree function rtinit_fib() under BURN_BRIDGES
to indicate that it might go away in the future.
No functional change.
Discussed with: julian [1] (clarification on what the original one meant)
Sponsored by: Cisco Systems, Inc.
While doing so, for consistency with the rtalloc_ign_fib(9) interface
called, remove the "in_" prefix from rtalloc_ign_wrapper() no longer
indicating that it would only handle the INET case.
Sponsored by: Cisco Systems, Inc.
tables (FIBs) as IPv4.
Prepare various general rt* functions for multi-FIB IPv6 handling in
addition to already existing multi-FIB IPv4 cases.
Sponsored by: Cisco Systems, Inc.
of the default one.
Without this change setting kern.cam.ada.default_timeout to 1 instead of 30
allowed me to trigger several false positive command timeouts under heavy
ZFS load on a SiI3132 siis(4) controller with 5 HDDs on a port multiplier.
MFC after: 1 week
netback.c: Add missing VM includes.
xen/xenvar.h,
xen/xenpmap.h: Move some XENHVM macros from <machine/xen/xenpmap.h> to
<machine/xen/xenvar.h> on i386 to match the amd64 headers.
conf/files: Add netback to the build.
Submitted by: jhb
MFC after: 3 days
Even having more specific hint.ata.X.mode controls, global ones are
still could be useful from some points, including compatibility.
PR: kern/164651
MFC after: 1 week
The cs driver requires a table with firmware values. An
alternative firmware is available in a similar Open Sound
System driver. This is actually a partial revert of
Revision 77504.
Special thanks to joel@ for patiently testing several
replacement attempts.
The csa driver and the complete sound system are now free
of the GPL.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
disconnected swap device.
This is quick and imperfect solution, as swap device will still be opened
and GEOM will not be able to destroy it. Proper solution would be to
automatically turn off and close disconnected swap device, but with existing
code it will cause panic if there is at least one page on device, even if
it is unimportant page of the user-level process. It needs some work.
Reviewed by: kib@
MFC after: 1 week
channels available
- current code treats bits 4:7 in 'SATAHC interrupt mask' and 'SATAHC
interrupt cause' as flags for SATA channels 2 and 3
- for embedded SATA controllers (SoC) these bits have been marked as reserved
in datasheets so far, but for some new and upcoming chips they are used for
purposes other than SATA
Submitted by: Lukasz Plachno
Reviewed by: mav
Obtained from: Semihalf
MFC after: 2 weeks
to cleanup routes from a single ifa.
o Implement carp_addroute()/carp_delroute() via above functions.
o Call carp_ifa_delroute() in the carp_detach() to avoid
junk routes left in routing table, in case if user
removes an address in a MASTER state. [1]
Reported by: az [1]
it is possible that a single AIO event will be reported to multiple
threads, it is not threading friendly, and the existing API can not
control this behavior.
Allocate a kevent flags field sigev_notify_kevent_flags for AIO event
notification in sigevent, and allow user to pass EV_CLEAR, EV_DISPATCH
or EV_ONESHOT to AIO kernel code, user can control whether the event
should be cleared once it is retrieved by a thread. This change should
be comptaible with existing application, because the field should have
already been zero-filled, and no additional action will be taken by
kernel.
PR: kern/156567
* Override the TX/RX stream count if the EEPROM reports a single RX or
TX stream, rather than assuming the device will always be a 2x2 strea
device.
* For AR9280 devices, don't hard-code 2x2 stream. Instead, allow the
ar5416FillCapabilityInfo() routine to correctly determine things.
The latter should be done for all 11n chips now that
ar5416FillCapabilityInfo() will set the TX/RX stream count based on the
active TX/RX chainmask in the EEPROM.
Thanks to Maciej Milewski for donating some AR9281 NICs to me for
testing.
hardware imposes strict limitations on hard buffer and block sizes.
Previous code set soft buffer to be no smaller then hard buffer. On some
cards with fixed 64K physical buffer that caused up to 800ms play latency.
New code allows to set soft buffer size down to just two blocks of the hard
buffer and to not write more then that size ahead to the hardware buffer.
As result of that change I was able to reduce full practically measured
record-playback loop delay in those conditions down to only about 115ms
with theoretical playback latency of only about 50ms.
New code works fine for both vchans and direct cases. In both cases sound(4)
tries to follow hw.snd.latency_profile and hw.snd.latency values and
application-requested buffer and block sizes as much as limitation of two
hardware blocks allows.
Reviewed by: silence on multimedia@
The isci driver is for the integrated SAS controller in the Intel C600
(Patsburg) chipset. Source files in sys/dev/isci directory are
FreeBSD-specific, and sys/dev/isci/scil subdirectory contains
an OS-agnostic library (SCIL) published by Intel to control the SAS
controller. This library is used primarily as-is in this driver, with
some post-processing to better integrate into the kernel build
environment.
isci.4 and a README in the sys/dev/isci directory contain a few
additional details.
This driver is only built for amd64 and i386 targets.
Sponsored by: Intel
Reviewed by: scottl
Approved by: scottl
any thread doing an I/O RPC with a transfer size greater than
NFS_UDPMAXDATA will be hung indefinitely, retrying the RPC.
After a discussion on freebsd-fs@, I decided to add a warning
message for this case, as suggested by Jeremy Chadwick.
Suggested by: freebsd at jdc.parodius.com (Jeremy Chadwick)
MFC after: 2 weeks
under the subject "F_RDLCK lock to FreeBSD NFS fails to R/O target file".
This occurred because the server side NLM always checked for VWRITE
access, irrespective of the type of lock request. This patch
replaces VOP_ACCESS(..VWRITE..) with one appropriate to
the lock operation. It allows unlock and lock cancellation
to be done without a check of VOP_ACCESS(), so that files
can't be left locked indefinitely after the file permissions
have been changed.
Discussed with: zack
Submitted by: jwd (earlier version)
Reviewed by: dfr
MFC after: 2 weeks
compliance testing.
In order to allow for radar pattern matching to occur, the DFS CAC/NOL
handling needs to be made configurable. This commit introduces a new
sysctl, "net.wlan.dfs_debug", which controls which DFS debug mode
net80211 is in.
* 0 = default, CSA/NOL handling as per normal.
* 1 = announce a CSA, but don't add the channel to the non-occupy list
(NOL.)
* 2 = disable both CSA and NOL - only print that a radar event occured.
This code is not compiled/enabled by default as it breaks regulatory
handling. A user must enable IEEE80211_DFS_DEBUG in their kernel
configuration file for this option to become available.
Obtained from: Atheros
* For legacy NICs, the combined RSSI should be used.
For earlier AR5416 NICs, use control chain 0 RSSI rather than combined
RSSI.
For AR5416 > version 2.1, use the combined RSSI again.
* Add in a missing AR5212 HAL method (get11nextbusy) which may be called
by radar code.
This serves no functional change for what's currently in FreeBSD.
about new child not only when doing PT_TO_SCX, but also for PT_CONTINUE.
If TDB_FORK flag is set, always issue a stop, the same as is done for
TDB_EXEC.
Reported by: Dmitry Mikulin <dmitrym juniper net>
MFC after: 1 week
that instead of using direct I/O it allows read-ahead similar to
POSIX_FADV_NORMAL, but invokes VOP_ADVISE(POSIX_FADV_DONTNEED) after the
read(2) has completed to purge just-read data. The write(2) path continues
to use direct I/O for POSIX_FADV_NOREUSE for now. Note that NOREUSE works
optimally if an application reads and writes full fs blocks.
that we have the lock now. This cleans up a locking panic ASSERT when
knlist_empty is called without a lock when INVARIANTS etc. are turned.
Reviewed by: kib jhb
MFC after: 1 week
so try harder to get the CDMA sync interrupt delivered and also in
a more efficient way:
- wrap the whole process of sending and receiving the CDMA sync
interrupt in a critical section so we don't get preempted,
- send the CDMA sync interrupt to the CPU that is actually waiting
for it to happen so we don't take a detour via another CPU,
- instead of waiting for up to 15 seconds for the interrupt to
trigger try the whole process for up to 15 times using a one
second timeout (the code was also changed to just ignore belated
interrupts of a previous tries should they appear).
According to testing done by Peter Jeremy with the debugging also
added as part of this commit the first two changes apparently are
sufficient to now properly get the CDMA sync interrupts delivered
at the first try though.
VIS-based block copy/zero implementations. While with 4BSD it's
sufficient to just disable the tick interrupts, with ULE+PREEMPTION
it's otherwise also possible that these are preempted via IPIs.
* Grab the net80211com lock when calling ieee80211_dfs_notify_radar().
* Use the tsf extend function to turn the 64 bit base TSF into a per-
frame 64 bit TSF. This will improve radiotap logging (which will
now have a (more) correct per-frame TSF, rather then the single TSF64
value read at the beginning of ath_rx_proc().
primitives by breaking stop_scheduler into a per-thread variable.
Also, store the new td_stopsched very close to td_*locks members as
they will be accessed mostly in the same codepaths as td_stopsched and
this results in avoiding a further cache-line pollution, possibly.
STOP_SCHEDULER() was pondered to use a new 'thread' argument, in order to
take advantage of already cached curthread, but in the end there should
not really be a performance benefit, while introducing a KPI breakage.
In collabouration with: flo
Reviewed by: avg
MFC after: 3 months (or never)
X-MFC: r228424
helper since r230632, use these for output and panicing during the
early cycles and move cninit() until after the static per-CPU data
has been set up. This solves a couple of issue regarding the non-
availability of the static per-CPU data:
- panic() not working and only making things worse when called,
- having to supply a special DELAY() implementation to the low-level
console drivers,
- curthread accesses of mutex(9) usage in low-level console drivers
that aren't conditional due to compiler optimizations (basically,
this is the problem described in r227537 but in this case for
keyboards attached via uart(4)). [1]
PR: 164123 [1]
implementing a simple OF_panic() that may be used during the early
cycles when panic() isn't available, yet.
- Mark cpu_{exit,shutdown}() as __dead2 as appropriate.
VM_KMEM_SIZE_SCALE to 2, awaiting more insight from alc@. As it turns
out, the VM apparently has problems with machines that have large holes
in the physical address space, causing the kmem_suballoc() call in
kmeminit() to fail with a VM_KMEM_SIZE_SCALE of 1. Using a value of 2
allows these, namely Blade 1500 with 2GB of RAM, to boot.
PR: 164227
cards powering up at once. Work around the easy case (multiple cards
inserted on boot) with a short sleep and a long comment. This
improves reliability on those laptops with power hungry cards.
excluding other allocations including UMA now entails the addition of
a single flag to kmem_alloc or uma zone create
Reviewed by: alc, avg
MFC after: 2 weeks
cleared/dropped leading to qid2tap[n] being NULL as there no longer
is a tap. Now, if there have been lots of frames queued the firmware
processes and returns those after the tap is gone.
Tested by: osa
MFC after: 1 week
NFS clients was reported to freebsd-fs@ under the subject "NFS
corruption in recent HEAD" on Nov. 26, 2011. This problem occurred when
a TCP mounted root fs was changed to using UDP. I believe that this
problem was caused by the change in mnt_stat.f_iosize that occurred
because rsize was decreased to the maximum supported by UDP. This
patch fixes the problem by using v_bufobj.bo_bsize instead of f_iosize,
since the latter is set to f_iosize when the vnode is allocated, but
does not change for a given vnode when f_iosize changes.
Reported by: pjd
Reviewed by: kib
MFC after: 2 weeks
Remove unneeded temporary variable (data) to better match the OSS code.
Remove some unused constants and type definitions.
Tested by: joel
Approved by: jhb (mentor)
MFC after: 3 weeks
referenced within its timeout window. This change clears the LLE_VALID flag when an llentry
is removed from an interface's hash table and adds an extra check to the flowtable code
for the LLE_VALID flag in llentry to avoid retaining and using a stale reference.
Reviewed by: qingli@
MFC after: 2 weeks
This involves significant changes to the mps(4) driver, but is not a
complete rewrite.
Some of the changes in this version of the driver:
- Integrated RAID (IR) support.
- Support for WarpDrive controllers.
- Support for SCSI protection information (EEDP).
- Support for TLR (Transport Level Retries), needed for tape drives.
- Improved error recovery code.
- ioctl interface compatible with LSI utilities.
mps.4: Update the mps(4) driver man page somewhat for the driver
changes. The list of supported hardware still needs to be
updated to reflect the full list of supported cards.
conf/files: Add the new driver files.
mps/mpi/*: Updated version of the MPI header files, with a BSD style
copyright.
mps/*: See above for a description of the new driver features.
modules/mps/Makefile:
Add the new mps(4) driver files.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: ken
MFC after: 1 week
data changes.
cam_ccb.h: Add a new advanced information type, CDAI_TYPE_RCAPLONG,
for long read capacity data.
cam_xpt_internal.h:
Add a read capacity data pointer and length to struct cam_ed.
cam_xpt.c: Free the read capacity buffer when a device goes away.
While we're here, make sure we don't leak memory for other
malloced fields in struct cam_ed.
scsi_all.c: Update the scsi_read_capacity_16() to take a uint8_t * and
a length instead of just a pointer to the parameter data
structure. This will hopefully make this function somewhat
immune to future changes in the parameter data.
scsi_all.h: Add some extra bit definitions to struct
scsi_read_capacity_data_long, and bump up the structure
size to the full size specified by SBC-3.
Change the prototype for scsi_read_capacity_16().
scsi_da.c: Register changes in read capacity data with the transport
layer. This allows the transport layer to send out an
async notification to interested parties. Update the
dasetgeom() API.
Use scsi_extract_sense_len() instead of
scsi_extract_sense().
scsi_xpt.c: Add support for the new CDAI_TYPE_RCAPLONG advanced
information type.
Make sure we set the physpath pointer to NULL after freeing
it. This allows blindly freeing it in the struct cam_ed
destructor.
sys/param.h: Bump __FreeBSD_version from 1000005 to 1000006 to make it
easier for third party drivers to determine that the read
capacity data async notification is available.
camcontrol.c,
mptutil/mpt_cam.c:
Update these for the new scsi_read_capacity_16() argument
structure.
Sponsored by: Spectra Logic
share/man/man4/Makefile,
share/man/man4/xnb.4,
sys/dev/xen/netback/netback.c,
sys/dev/xen/netback/netback_unit_tests.c:
Rewrote the netback driver for xen to attach properly via newbus
and work properly in both HVM and PVM mode (only HVM is tested).
Works with the in-tree FreeBSD netfront driver or the Windows
netfront driver from SuSE. Has not been extensively tested with
a Linux netfront driver. Does not implement LRO, TSO, or
polling. Includes unit tests that may be run through sysctl
after compiling with XNB_DEBUG defined.
sys/dev/xen/blkback/blkback.c,
sys/xen/interface/io/netif.h:
Comment elaboration.
sys/kern/uipc_mbuf.c:
Fix page fault in kernel mode when calling m_print() on a
null mbuf. Since m_print() is only used for debugging, there
are no performance concerns for extra error checking code.
sys/kern/subr_scanf.c:
Add the "hh" and "ll" width specifiers from C99 to scanf().
A few callers were already using "ll" even though scanf()
was handling it as "l".
Submitted by: Alan Somers <alans@spectralogic.com>
Submitted by: John Suykerbuyk <johns@spectralogic.com>
Sponsored by: Spectra Logic
MFC after: 1 week
Reviewed by: ken
- add "+HP" in case of headphones redirection;
- add device type for analog devices, if all pins have the same.
As result now it may look like "Analog 5.1+HP/2.0" or "Front Analog Mic".
I hope it will be more useful than long and confusing.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
casted types: to ssize_t in filesystem code and to
int in buf code, thus supplying a negative argument
leads to kernel panic later. To fix that check user
supplied argument in the beginning of syscall.
Submitted by: Maxim Dounin <mdounin mdounin.ru>, maxim@
- remove experimental code for disabling CRC
- use the correct constant for conversion between interrupt rate
and EITR values (the previous values were off by a factor of 2)
- make dev.ix.N.queueM.interrupt_rate a RW sysctl variable.
Changing individual values affects the queue immediately,
and propagates to all interfaces at the next reinit.
- add dev.ix.N.queueM.irqs rdonly sysctl, to export the actual
interrupt counts
Netmap-related changes for ixgbe:
- use the "new" format for TX descriptors in netmap mode.
- pass interrupt mitigation delays to the user process doing poll()
on a netmap file descriptor.
On the RX side this means we will not check the ring more than once
per interrupt. This gives the process a chance to sleep and process
packets in larger batches, thus reducing CPU usage.
On the TX side we take this even further: completed transmissions are
reclaimed every half ring even if the NIC interrupts more often.
This saves even more CPU without any additional tx delays.
Generic Netmap-related changes:
- align the netmap_kring to cache lines so that there is no false sharing
(possibly useful for multiqueue NICs and MSIX interrupts, which are
handled by different cores). It's a minor improvement but it does not
cost anything.
Reviewed by: Jack Vogel
Approved by: Jack Vogel
Unmounts do vfs_msync() before calling VFS_UNMOUNT(), but there is
still a race allowing a process to dirty pages after msync
finished. Remounts rw->ro just left dirty pages in system.
Reviewed by: alc, tegge (long time ago)
Tested by: pho
MFC after: 2 weeks
appropriate timestamps. Restore the assertions which verify that
NCF_TS is set when timestamp is asked for.
Reviewed by: jhb (previous version)
MFC after: 2 weeks
selection in snd_hda(4) driver.
Now driver tracks jack presence detection status for every CODEC pin. For
playback associations, when configured, that information, same as before,
can be used to automatically redirect audio to headphones. Also same as
before, these events are used to track digital display connection status
and fetch ELD. Now in addition to that driver uses that information to
automatically switch recording source of the mixer to the connected input.
When there are devices with no jack detection and with one both connected,
last ones will have the precedence. As result, on most laptops after boot
internal microphone should be automatically selected. But if external one
(for example, headset) connected, it will be selected automatically.
When external mic disconnected, internal one will be selected again.
Automatic recording source selection is enabled by default now to make
recording work out of the box without touching mixer. But it can be
disabled or limited only to attach time using hint.pcm.X.rec.autosrc loader
tunables or dev.pcm.X.rec.autosrc sysctls.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
we will only trust a positive name cache entry for a specified amount of
time before falling back to a LOOKUP RPC, even if the ctime for the file
handle matches the cached copy in the name cache entry. The timeout is
configured via a new 'nametimeo' mount option and defaults to 60 seconds.
It may be set to zero to disable positive name caching entirely.
Reviewed by: rmacklem
MFC after: 1 week
- Enter instead of ENTER
- Remove colons
- Line up option values
- Use dots to provide a line to visually connect the menu
selections with their values
- Replace Enabled/Disabled with off/On
(bigger inital cap for "On" is a visual indicator)
- Remove confusing "Boot" from selections that don't boot.
- With loader_color=1 in /boot/loader.conf, use reverse video to
highlight enabled options
PR: misc/160818
Submitted by: Warren Block <wblock wonkity com>
Reviewed by: Devin Teske <devin dot teske fisglobal com>, current@
MFC after: 1 week
in response to CAM_DEV_NOT_THERE, instead of just the LUN in question.
This will now just eliminate the specified LUN in response to
CAM_DEV_NOT_THERE.
Reported by: Richard Todd <rmtodd@servalan.servalan.com>
MFC after: 3 days
The actual ia6->ia6_lifetime access is hidden in
IFA6_IS_INVALID/IFA6_IS_DEPRECATED macros since a long time ago
(see netinet6/nd6.c, r1.104 of KAME for the reference).
MFC after: 3 days
from TCP to UDP and the rsize/wsize/readdirsize is greater
than NFS_MAXDGRAMDATA, it is possible for a thread doing an
I/O RPC to get stuck repeatedly doing retries. This happens
because the RPC will use a resize/wsize/readdirsize that won't
work for UDP and, as such, it will keep failing indefinitely.
This patch returns an error for this case, to avoid the problem.
A discussion on freebsd-fs@ seemed to indicate that returning
an error was preferable to silently ignoring the "udp"/"mntudp"
option.
This problem was discovered while investigating a problem reported
by pjd@ via email.
MFC after: 2 weeks
(HDMI and HBR bits set) and needed (AC3 format used with 8 channels).
This should allow DTS-HD/TrueHD pass-through with rates above 6.144Mbps.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
consistently, creating some namecache entries without NCF_TS flag.
This causes panic due to failed assertion.
As a temporal relief, remove the assert. Return epoch timestamp for
the entries without timestamp if asked.
While there, consolidate the code which returns timestamps, into a
helper cache_out_ts().
Discussed with: jhb
MFC after: 2 weeks
widgets. I am not sure if S/PDIF supports 32bit samples, but my Marantz
SR4001 doesn't, producing only single clicks on playback start/stop.
Because HDA controller requires 32bit alignment for all samples above 16bit,
we can't handle this situation in regular way and have to set 32bit format
in sound(4) for anything above 16bit. To workaround the problem, prefer
to setup hardware to use 24/20bit samples when 32bit format requested. Add
dev.pcm.X.play.32bit and dev.pcm.X.rec.32bit sysctls to control what format
really use for 32bit samples.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
hash with names of its hooks. It starts with size of 16, and
grows when number of hooks reaches twice the current size. A
failure to grow (memory is allocated with M_NOWAIT) isn't
fatal, however.
I used standard hash(9) function for the hash. With 25000
hooks named in the mpd (ports/net/mpd5) manner of "b%u", the
distributions is the following: 72.1% entries consist of one
element, 22.1% consist of two, 5.2% consist of three and
0.6% of four.
Speedup in a synthetic test that creates 25000 hooks and then
runs through a long cyclce dereferencing them in a random order
is over 25 times.
mutex(9) to rwlock(9) based locks.
While here remove dropping lock when processing NGM_LISTNODES,
and NGM_LISTTYPES generic commands. We don't need to drop it
since memory allocation is done with M_NOWAIT.
- retrive only one, specified limit for a process, not the whole
array, as it was previously (the sysctl has been added recently and
has not been backported to stable yet, so this change is ok);
- allow to set a resource limit for another process.
Submitted by: Andrey Zonov <andrey at zonov.org>
Discussed with: kib
Reviewed by: kib
MFC after: 2 weeks
maximal from 64K to 256K.
We usually don't need 750 sound interrupts per second (1.3ms latency)
when playing 192K/24/8 stream. 187 should be better. On usual 48K/16/2
it is just enough for hw.snd.latency=9 at hw.snd.latency_profile=1 with
23 and 6 interrupts per second.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
Previous code was relatively dumb. During CODEC probe it was tracing signals
and statically binding amplifier controls to the OSS mixer controls. To set
volume it just set all bound amplifier controls proportionally to mixer
level, not looking on their hierarchy and amplification levels/offsets.
New code is much smarter. It also traces signals during probe, but mostly
to find out possible amplification control rages in dB for each specific
signal. To set volume it retraces each affected signal again and sets
amplifiers controls recursively to reach desired amplification level in dB.
It would be nice to export values in dB to user, but unluckily our OSS mixer
API is too simple for that.
As result of this change:
- cascaded amplifiers will work together to reach maximal precision.
If some input has 0/+40dB preamplifier with 10dB step and -10/+10dB mixer
with 1dB step after it, new code will use both to provide 0/+40dB control
with 1dB step! We could even get -10/+50dB range there, but that is
intentionally blocked for now.
- different channels of multichannel associations on non-uniform CODECs
such as VIA VT1708S will have the same volume, not looking that control
ranges are different. It was not good when fronts were 12dB louder.
- for multiplexed recording, when we can record from only one source at
a time, we can now use recording amplifier controls to set different
volume levels for different inputs if they have no own controls of they
are less precise. If recording source change, amplifiers will be
reconfigured.
To improve out-of-the-box behavior, ignore default volume levels set by
sound(4) and use own, more reasonable: +20dB for mics, -10dB for analog
output volume and 0dB for the rest of controls. sound(4) defaults of 75%
mean absolutely random things for different controls of different CODECs
because of very different control ranges.
Together with further planned automatic recording source selection this
should allow users to get fine playback and recording without touching
mixer first.
Note that existing users should delete /var/db/mixer*-state and reboot
or trigger CODEC reconfiguration to get new default values.
MFC after: 2 months
Sponsored by: iXsystems, Inc.
This makes it much easier to determine whether an event occurs in the
net80211 taskqueue (which was called "ath0 taskq") or the ath driver
taskqueue (which is also called "ath0 taskq".)
comments to longer, also refining strange ones.
Properly use #ifdef rather than #if defined() where possible. Four
#if defined(PCBGROUP) occurances (netinet and netinet6) were ignored to
avoid conflicts with eventually upcoming changes for RSS.
Reported by: bde (most)
Reviewed by: bde
MFC after: 3 days
