- While here, make this compile and work on non-i386:
- Use CMSG_SPACE(), CMSG_LEN(), and CMSG_FIRSTHDR() instead of ignoring
padding between 'struct cmsghdr' and control message payloads.
- Don't initialize the control message before calling recvmsg().
Instead, check that we get a valid control message on return from
recvmsg().
- Use errx() instead of err() for some errors that don't report failures
that set errno.
Requested by: kib (1)
control. Controller does not automatically generate pause frames
based on number of available RX buffers so it's very hard to
know when driver should generate XON frame in time. The only
mechanism driver can detect low number of RX buffer condition is
ET_INTR_RXRING0_LOW or ET_INTR_RXRING1_LOW interrupt. This
interrupt is generated whenever controller notices the number of
available RX buffers are lower than pre-programmed value(
ET_RX_RING0_MINCNT and ET_RX_RING1_MINCNT register). This scheme
does not provide a way to detect when controller sees enough number
of RX buffers again such that efficient generation of XON/XOFF
frame is not easy.
While here, add more flow control related register definition.
interrupt is ours. Note, interrupts are automatically ACKed when
the status register is read.
Add RX/TX DMA error to interrupt handler and do full controller
reset if driver happen to encounter these errors. There is no way
to recover from these DMA errors without controller reset.
Rename local variable name intrs with status to enhance
readability.
While I'm here, rename ET_INTR_TXEOF and ET_INTR_RXEOF to
ET_INTR_TXDMA and ET_INTR_RXDMA respectively. These interrupts
indicate that a frame is successfully DMAed to controller's
internal FIFO and they have nothing to do with EOF(end of frame).
Driver does not need to wait actual end of TX/RX of a frame(e.g.
no need to wait the end signal of TX which is generated when a
frame in TX FIFO is emptied by MAC). Previous names were somewhat
confusing.
of a devfs file descriptor in devfs_close_f(). The passed in td argument
may be NULL if the close was invoked by garbage collection of open
file descriptors in pending control messages in the socket buffer of a
UNIX domain socket after it was closed.
PR: kern/151758
Submitted by: Andrey Shidakov andrey shidakov ru
Submitted by: Ruben van Staveren ruben verweg com
Reviewed by: kib
MFC after: 2 weeks
thread_free(newtd). This to avoid a possible page fault in
cpu_thread_clean() as seen on amd64 with syscall fuzzing.
Reviewed by: kib
MFC after: 1 week
: 2011-10-23 Ingo Schwarze <schwarze@openbsd.org>
:
: [mdoc] Synchronize string tables with the mandoc(1) utility.
:
: * tmac/doc-common: Add many architecture names used in NetBSD and
: OpenBSD (and "arm" from FreeBSD) and remove the duplicate OS version
: entry for Darwin-10.6.0.
:
: * tmac/doc-syms: Add many library names used in NetBSD and FreeBSD.
:
: * tmac/groff_mdoc.man: Document all supported architecture names, OS
: versions, and library names.
:
: 2011-09-11 Joseph Koshy <jkoshy@users.sourceforge.net>
:
: [mdoc] Add some library strings.
:
: * tmac/doc-syms: Add `libdwarf' and `libelf'.
: * tmac/groff_mdoc.man: Document them.
:
: 2011-07-03 Guillem Jover <guillem@debian.org>
:
: mdoc: Update more OS versions strings.
:
: * tmac/doc-common: Add versions strings for NetBSD, OpenBSD,
: FreeBSD, and DragonFly.
suspend state. This will save more power.
On resume, make sure to enable all clocks. While I'm here, if
controller is not fast ethernet, enable gigabit PHY.
Don't blindly re-initialize controller whenever MTU is changed.
Now, reinitializing is done only when driver is running.
While here, remove unnecessary assignment of error value since it
was already initialized to 0.
o Do not report link status if driver is not running.
o TX/RX MAC configuration should be done with resolved speed,
duplex and flow control after establishing a link so it can't
be done in driver initialization routine.
Move the configuration to miibus_statchg callback which will be
called whenever any link state change is detected.
At this moment, flow-control is not enabled yet mainly because
I was not able to set correct flow control parameters to
generate TX pause frames.
o Now TX/RX MAC is enabled only when a valid link is detected.
Rearragnge hardware initialization routine a bit to leave
enabling MAC to miibus_statchg callback. In order to that,
TX/RX DMA engine is enabled in et_init_locked().
o Introduce ET_FLAG_LINK flag to track current link state.
o Introduce ET_FLAG_FASTETHER flag to mark whether controller is
fast ethernet. This flag is checked in miibus_statchg callback
to know whether PHY established a valid link.
o In et_stop(), TX/RX MAC is explicitly disabled instead of
relying on et_reset(). And move et_reset() from et_stop() to
controller initialization. Controler reset is not required here
and it would also clear critial registers(i.e station address,
RX filter configuration, WOL etc) that are required to make WOL
work.
o Switching to current media is done in et_init_locked() after
setting IFF_DRV_RUNNING flag. This should ensure reliable
auto-negotiation/manual link establishment.
o In et_start_locked(), check whether driver got a valid link
before trying to send frames.
o Remove checking a link in et_tick() as this is done by
miibus_statchg callback.
identifier reserved for the implementation in C99 and earlier so there is
no sensible reason for introducing yet another reserved identifier when we
could just use the one C1x uses.
Approved by: brooks (mentor)
with clang, by removing two unneeded using declarations. Otherwise, you
would get errors similar to:
/usr/include/c++/4.2/debug/map.h:77:20: error: dependent using declaration resolved to type without 'typename'
using _Base::value_compare;
^
N.B.: Take care when you actually use the debug versions of any
libstdc++ header. They are more likely to contain problems, because
they are exercised far less often, and since the standard library
complexity guarantees don't always apply anymore, compile times can
drastically increase.
MFC after: 2 weeks
manipulation of interrupt register access is done through
CSR_WRITE_4 macro. Also add disabling interrupt into et_reset()
because we want interrupt disabled state after controller reset.
While I'm here slightly change interrupt handler to be more
readable one.
send a single TX command after setting up all TX frames. This
removes unnecessary register accesses and bus_dmamap_sync(9) calls.
et(4) uses TX interrupt moderation so it's possible to have TX
buffers that were already transmitted but waiting for TX completion
interrupt. If the number of available TX descriptor is less then
1/3 of total TX descriptor, try reclaiming first to get enough free
TX descriptors before setting up TX descriptors.
After r228325, et_txeof() no longer tries to send frames after
reclaiming TX buffers. That change was made to give more chance
to transmit frames in main interrupt handler since we can still
send frames in interrupt handler with RX interrupt. So right
before exiting interrupt hander, after enabling interrupt, try to
send more frames. This gives slightly better performance numbers.
While I'm here reduce number of spare TX descriptors from 8 to 4.
Controller does not require reserved TX descriptors, it was just to
reduce TX overhead. After r228325, driver has much lower TX
overhead so it does not make sense to reserve 8 TX descriptors.
change should make et(4) work on any architectures.
o Remove m_getl inline function and replace it with stanard mbuf
interfaces. Previous code tried to minimize code duplication
but this came from incorrect use of common DMA tag.
Driver may be still use a common RX allocation handler with
additional structure changes but I don't see much point to do
that it would make it hard to understand the code.
o Remove DragonflyBSD specific constant EVL_ENCAPLEN, use
ETHER_VLAN_ENCAP_LEN instead.
o Add bunch of new RX status definition. It seems controller
supports RX checksum offloading but I was not able to make the
feature work yet. Currently driver checks whether recevied
frame is good one or not.
o Avoid a typedef ending in '_t' as style(9) says.
o Controller has no restriction on DMA address space, so there
is no reason to limit the DMA address to 32bit. Descriptor
rings, status blocks and TX/RX buffers now use full 64bit DMA
addressing.
o Allocate DMA memory shared between host and controller as
coherent.
o Create 3 separate DMA tags to be used as TX, mini RX ring and
stanard RX ring. Previously it created a single DMA tag and it
was used to all three rings.
o et(4) does not support jumbo frame at this moment and I still
don't quite understand how jumbo frame works on this controller
so use two RX rings to handle small sized frame and normal sized
frame respectively. The mini RX ring will be used to receive
frames that are less than or equal to 127 bytes. The second RX
ring is used to receive frames that are not handled by the first
RX ring.
If jumbo frame support is implemented, driver may have to choose
better RX scheme by letting the second RX ring handle jumbo
frames. This scheme will mimic Broadcom's efficient jumbo frame
handling feature. However RAM buffer size(16KB) of the
controller is too small to hold 2 jumbo frames, if 9KB
jumbo frame is used, I'm not sure how good performance would it
have.
o In et_rxeof(), make sure to check whether controller received
good frame or not. Passing corrupted frame to upper layer is
bad idea.
o If driver receives a bad frame or driver fails to allocate RX
buffer due to resource shortage condition, reuse previously
loaded DMA map for RX buffer instead of unloading/loading RX
buffer again.
o et_init_tx_ring() never fails so change return type to void.
o In watchdog handler, show TX DMA write back status of errored
frame which could be used as a clue to debug watchdog timeout.
o Add missing bus_dmamap_sync() in various places such that et(4)
should work with bounce buffers(e.g. PAE).
o TX side bus_dmamap_load_mbuf_sg(9) support.
o RX side bus_dmamap_load_mbuf_sg(9) support.
o Controller has no DMA alignment limit in RX buffer so use
m_adj(9) in RX buffer allocation to make IP header align on 2
bytes boundary. Otherwise it would trigger unaligned access
error in upper layer on strict alignment architectures.
One of down side of controller is it provides limited set of RX
buffer length like most Intel controllers. This is not problem
at this moment because driver does not support jumbo frame yet
but it may require alignment fixup code to support jumbo frame
on strict alignment architectures.
o In et_txeof(), don't zero TX descriptors for transmitted frames.
TX descriptors don't need write access after transmission.
Driver sets IFF_DRV_OACTIVE when the number of available TX
descriptors are less than or equal to ET_NSEG_SPARE. Make sure
to clear IFF_DRV_OACTIVE only when the number of available TX
descriptor is greater than ET_NSEG_SPARE.
__noreturn macro and modify the other exiting functions to use it.
The __noreturn macro, unlike __dead2, must be used BEFORE the function.
This is in line with the C and C++ specifications that place _Noreturn (c1x)
and [[noreturn]] (C++11) in front of the functions. As with __dead2, this
macro falls back to using the GCC attribute.
Unfortunately, clang currently sets the same value for the C version macro
in C99 and C1x modes, so these functions are hidden by default. At some
point before 10.0, I need to go through the headers and clean up the C1x /
C++11 visibility.
Reviewed by: brooks (mentor)
of vm_kmem_size that may occur if the system administrator has specified a
vm.vm_kmem_size tunable value that exceeds the hard cap.
PR: 162741
Submitted by: Adam McDougall
Reviewed by: bde@
MFC after: 3 weeks
against text. Provide the override switch to turn off the strict
behaviour. Apparently, openssl libcrypto needs it due to assembler
code not being PIC.
Discussed with: bf
MFC after: 2 weeks
Optimize for the case, by lazily allocating the pipe inode number at the
fstat(2) time. If alloc_unr(9) returns failure, do not fail fstat(2), since
uses of inode numbers are even rare then fstat(2), but provide zero inode
forever. Note that alloc_unr() failure is unlikely due to total number
of pipes in the system limited by the number of file descriptors.
Based on the submission by: gianni
MFC after: 2 weeks