the main processing queue, clear the NAK counter for any associated
BULK or CONTROL transfers and poll the endpoint(s) for 1 millisecond
at 125us rate interval, before going into slow, 10ms, NAK polling mode
again. This has the effect that typical ping-ping protocols respond
quicker when initiated from the USB host.
MFC after: 2 weeks
The last obstacle to switching PowerPC entirely to vt is that the Playstation 3
framebuffer driver needs to be ported over. This only applies for powerpc64,
however.
on my G4 iBook by more than half. Still 10% slower than syscons, but that's
much better than a factor of 2.
The slowness had to do with pathological write performance on 8-bit
framebuffers, which are almost universally used on Open Firmware systems.
Writing 1 byte at a time, potentially nonconsecutively, resulted in many
extra PCI write cycles. This patch, in the common case where it's writing
one or several characters in an 8x8 font, gangs the writes together into
a set of 32-bit writes. This is a port of r143830 to vt(4).
The EFI framebuffer is also extremely slow, probably for the same reason,
and the same patch will likely help there.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
- For non-periodic traffic we only need to wait two SOFs before
disabling the channel.
- Make sure we release the TX FIFO tracking level after the host
channel is disabled.
- Make sure the host channel state gets reset/disabled initially.
- Two minor code style changes.
MFC after: 2 weeks
- Rework how we allocate and free USB host channels, so that we only
allocate a channel if there is a real packet going out on the USB
cable.
- Use BULK type for control data and status, due to instabilities in
the HW it appears.
- Split FIFO TX levels into one for the periodic FIFO and one for the
non-periodic FIFO.
- Use correct HFNUM mask when scheduling host transactions. The HFNUM
register does not count the full 16-bit range.
- Correct START/COMPLETION slot for TT transactions. For INTERRUPT and
ISOCHRONOUS type transactions the hardware always respects the ODDFRM
bit, which means we need to allocate multiple host channels when
processing such endpoints, to not miss any so-called complete split
opportunities.
- When doing ISOCHRONOUS OUT transfers through a TT send all data
payload in a single ALL-burst. This deacreases the likelyhood for
isochronous data underruns.
- Fixed unbalanced unlock in case of "dwc_otg_init_fifo()" failure.
- Increase interrupt priority.
MFC after: 2 weeks
have implemented the PIM_NOSCAN rescan functionality will have it
enabled.
This is a no-op for head.
Reviewed by: slm
Sponsored by: Spectra Logic Corporation
MFC after: 3 days
TLR is necessary for reliable communication with SAS tape drives.
This was broken by change 246713 in the mps(4) driver. It changed the
cm_data field for SCSI I/O requests to point to the CCB instead of the data
buffer. So, instead, look at the CCB's data pointer to determine whether
or not we're talking to a tape drive.
Also, take the residual into account to make sure that we don't go off the
end of the request.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
cards. LSI has been maintaining this driver outside of the FreeBSD
tree. It overlaps support of ThunderBolt and Invader cards that mfi(4)
supports. By default mfi(4) will attach to cards. If the tunable:
hw.mfi.mrsas_enable=1
is set then mfi(4) will not probe and attach to these newer cards and
allow mrsas(4) to attach. So by default this driver will not effect
a FreeBSD system unless mfi(4) is removed from the kernel or the
tunable is enabled.
mrsas(4) attaches disks to the CAM layer so it depends on CAM and devices
show up as /dev/daX. mfiutil(8) does not work with mrsas. The FreeBSD
version of MegaCli and StorCli from LSI do work with mrsas. It appears
that StorCli only works with mrsas. MegaCli appears to work with mfi(4)
and mrsas(4).
It would be good to add mfiutil(4) support to mrsas, emulations modes,
kernel logging, device aliases to ease the transition between mfi(4)
and mrsas(4).
Style issues should be resolved by LSI when they get committers approved.
The plan is get this driver in FreeBSD 9.3 to improve HW support.
Thanks to LSI for developing, testing and working with FreeBSD to
make this driver co-exist in FreeBSD. This improves the overall
support of MegaRAID SAS.
Submitted by: Kashyap Desai <Kashyap.Desai@lsi.com>
Reviewed by: scottl
MFC after: 3 days
Sponsored by: LSI
mprsas_SSU_to_SATA_devices().
This fixes an assertion on shutdown with INVARIANTS enabled with SATA
drives present on an IR firmware controller.
Reviewed by: Steve McConnell <stephen.mcconnell@avagotech.com>.
MFC after: 3 days
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
This problem only occurs on versions of FreeBSD prior to the recent CAM
locking changes. (i.e. stable/9 and older versions of stable/10) This
change should be a no-op for head and stable/10.
If a path isn't specified, xpt_register_async() will create a fully
wildcarded path and acquire a lock (the XPT lock in older versions,
and via xpt_path_lock() in newer versions) to call xpt_action() for the
XPT_SASYNC_CB CCB. It will then drop the lock and if the requested event
includes AC_FOUND_DEVICE or AC_PATH_REGISTERED, it will get the caller up
to date with any device arrivals or path registrations.
The issue is that before the locking changes, each SIM lock would get
acquired in turn during the EDT tree traversal process. If a path is
specified for xpt_register_async(), it won't acquire and drop its own lock,
but instead expects the caller to hold its own SIM lock. That works for
the first part of xpt_register_async(), but causes a recursive lock
acquisition once the EDT traversal happens and it comes to the SIM in
question. And it isn't possible to call xpt_action() without holding a SIM
lock.
The locking changes fix this by using the XPT topology lock for EDT
traversal, so it is no longer an issue to hold the SIM lock while calling
xpt_register_async().
The solution for FreeBSD versions before the locking changes is to request
notification of all device arrivals (so we pass a NULL path into
xpt_register_async()) and then filter out the arrivals that are not ours.
MFC After: 3 days
Sponsored by: Spectra Logic Corporation
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
o Declare vt(4) drivers dataset.
o Create single static structures for all early drivers.
o Add vt(4) to be by default in the kernel consoles list.
o Create one more sysinit point, to be able to initialize memory and lock
requirement of early drivers.
o Implement early drivers select. (Only best available will be selected).
o Fix one missed "return (0)" for VTYLOCK.
o Improve locking for cases when one driver replace another.
o Make driver replacement notification less debug-look-like.
Minor spell fixes.
Sponsored by: The FreeBSD Foundation
reflect when unmapped I/O support was added.
For FreeBSD 10, it arrived just prior to __FreeBSD_version 1000028.
For FreeBSD 9, it arrived just prior to __FreeBSD_version 902001.
Also, fix compiler warnings in mprsas_send_smpcmd() that happen in the
i386 PAE build for non-unmapped I/O builds. These were fixed in mps(4)
in revision 241145, but didn't make it into the mpr(4) driver. This
change should only affect FreeBSD versions outside the above revisions,
and thus doesn't affect head.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
call, which assumes the hardware is awake.
Turn ath_update_mcast() into a routine that's only called from the
net80211 layer - and it forces the hardware awake first.
This fixes a LOR from the EDMA RX path which calls ath_mode_init()
with the RX lock held - the driver lock can't also be grabbed.
This path assumes that the ath_mode_init() callers all wake up
the NIC first.
Tested:
* AR9485, STA mode, powersave
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
sys/systm.h must always come after sys/param.h.
Remove sys/types.h which should never be included together with sys/param.h.
Add sys/malloc.h for correctness even if it seems to don't be needed.
Remove more unused headers found by unusedinc (from bde@) and tested with a
universe build.
Reported by: bde
This allows to run 32bit applications on a 64bit host. This was tested
successfully with Wine (emulators/i386-wine-devel) and StarCraft II.
Submitted by: Jan Kokemüller <jan.kokemueller@gmail.com>
MFC after: 1 week
This is derived from the mps(4) driver, but it supports only the 12Gb
IT and IR hardware including the SAS 3004, SAS 3008 and SAS 3108.
Some notes about this driver:
o The 12Gb hardware can do "FastPath" I/O, and that capability is included in
this driver.
o WarpDrive functionality has been removed, since it isn't supported in
the 12Gb driver interface.
o The Scatter/Gather list handling code is significantly different between
the 6Gb and 12Gb hardware. The 12Gb boards support IEEE Scatter/Gather
lists.
Thanks to LSI for developing and testing this driver for FreeBSD.
share/man/man4/mpr.4:
mpr(4) man page.
sys/dev/mpr/*:
mpr(4) driver files.
sys/modules/Makefile,
sys/modules/mpr/Makefile:
Add a module Makefile for the mpr(4) driver.
sys/conf/files:
Add the mpr(4) driver.
sys/amd64/conf/GENERIC,
sys/i386/conf/GENERIC,
sys/mips/conf/OCTEON1,
sys/sparc64/conf/GENERIC:
Add the mpr(4) driver to all config files that currently
have the mps(4) driver.
sys/ia64/conf/GENERIC:
Add the mps(4) and mpr(4) drivers to the ia64 GENERIC
config file.
sys/i386/conf/XEN:
Exclude the mpr module from building here.
Submitted by: Steve McConnell <Stephen.McConnell@lsi.com>
MFC after: 3 days
Tested by: Chris Reeves <chrisr@spectralogic.com>
Sponsored by: LSI, Spectra Logic
Relnotes: LSI 12Gb SAS driver mpr(4) added
lindev(4) was only used to provide /dev/full which is now a standard feature of
FreeBSD. /dev/full was never linux-specific and provides a generally useful
feature.
Document this in UPDATING and bump __FreeBSD_version. This will be documented
in the PH shortly.
Reported by: jkim
