This adds sys/modules/imx with a SUBDIR makefile to make the whole
collection of modules that are specific to these SoCs. Initially, that
"whole collection" consists of the if_ffec and imx_i2c drivers.
The if_ffec driver is referenced in its existing home in ../ffec rather
than moving it into the imx directory, because it's used by powerpc too,
but it is no longer built for all armv6/7 systems.
The imx_i2c driver is newly added as a module.
compilation under FreeBSD. The mthca driver was temporarily removed as
part of the Linux 4.9 RoCE/infinband upgrade.
Top commit in Linux source tree:
69973b830859bc6529a7a0468ba0d80ee5117826
Sponsored by: Mellanox Technologies
o added struct ipfw_dyn_info that keeps all needed for ipfw_chk and
for dynamic states implementation information;
o added DYN_LOOKUP_NEEDED() macro that can be used to determine the
need of new lookup of dynamic states;
o ipfw_dyn_rule now becomes obsolete. Currently it used to pass
information from kernel to userland only.
o IPv4 and IPv6 states now described by different structures
dyn_ipv4_state and dyn_ipv6_state;
o IPv6 scope zones support is added;
o ipfw(4) now depends from Concurrency Kit;
o states are linked with "entry" field using CK_SLIST. This allows
lockless lookup and protected by mutex modifications.
o the "expired" SLIST field is used for states expiring.
o struct dyn_data is used to keep generic information for both IPv4
and IPv6;
o struct dyn_parent is used to keep O_LIMIT_PARENT information;
o IPv4 and IPv6 states are stored in different hash tables;
o O_LIMIT_PARENT states now are kept separately from O_LIMIT and
O_KEEP_STATE states;
o per-cpu dyn_hp pointers are used to implement hazard pointers and they
prevent freeing states that are locklessly used by lookup threads;
o mutexes to protect modification of lists in hash tables now kept in
separate arrays. 65535 limit to maximum number of hash buckets now
removed.
o Separate lookup and install functions added for IPv4 and IPv6 states
and for parent states.
o By default now is used Jenkinks hash function.
Obtained from: Yandex LLC
MFC after: 42 days
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D12685
FreeBSD boots on this board, but the ethernet switch is not currently
supported, resulting in no ethernet.
A U-Boot port will be added once the ethernet switch is at least basically
supported, but we add its DTS to the build here to lower the barrier-to-boot
while work is underway.
- Remove the shim interface that allowed bwn(4) to use either siba_bwn or
bhnd(4), replacing all siba_bwn calls with their bhnd(4) bus equivalents.
- Drop the legay, now-unused siba_bwn bus driver.
- Clean up bhnd(4) board flag defines referenced by bwn(4).
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13518
instead of frobbing the registers directly.
As a hack the bcm2835_pwm kmod presently ignores the 'status="disabled"'
in the RPI3 DTB, assuming that if you load the kld you probably
want the PWM to work.
The logical result of a right shift >= the width of a type is zero, but our
compiler decides this is a warning (and thus, error). Just remove ccp(4)
from i386.
Reported by: cy
Sponsored by: Dell EMC Isilon
* Registers TRNG source for random(4)
* Finds available queues, LSBs; allocates static objects
* Allocates a shared MSI-X for all queues. The hardware does not have
separate interrupts per queue. Working interrupt mode driver.
* Computes SHA hashes, HMAC. Passes cryptotest.py, cryptocheck tests.
* Does AES-CBC, CTR mode, and XTS. cryptotest.py and cryptocheck pass.
* Support for "authenc" (AES + HMAC). (SHA1 seems to result in
"unaligned" cleartext inputs from cryptocheck -- which the engine
cannot handle. SHA2 seems to work fine.)
* GCM passes for block-multiple AAD, input lengths
Largely based on ccr(4), part of cxgbe(4).
Rough performance averages on AMD Ryzen 1950X (4kB buffer):
aesni: SHA1: ~8300 Mb/s SHA256: ~8000 Mb/s
ccp: ~630 Mb/s SHA256: ~660 Mb/s SHA512: ~700 Mb/s
cryptosoft: ~1800 Mb/s SHA256: ~1800 Mb/s SHA512: ~2700 Mb/s
As you can see, performance is poor in comparison to aesni(4) and even
cryptosoft (due to high setup cost). At a larger buffer size (128kB),
throughput is a little better (but still worse than aesni(4)):
aesni: SHA1:~10400 Mb/s SHA256: ~9950 Mb/s
ccp: ~2200 Mb/s SHA256: ~2600 Mb/s SHA512: ~3800 Mb/s
cryptosoft: ~1750 Mb/s SHA256: ~1800 Mb/s SHA512: ~2700 Mb/s
AES performance has a similar story:
aesni: 4kB: ~11250 Mb/s 128kB: ~11250 Mb/s
ccp: ~350 Mb/s 128kB: ~4600 Mb/s
cryptosoft: ~1750 Mb/s 128kB: ~1700 Mb/s
This driver is EXPERIMENTAL. You should verify cryptographic results on
typical and corner case inputs from your application against a known- good
implementation.
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12723
Since r326501 which added COMPAT_FREEBSD32 to the GENERIC config for arm64,
we need to build systrace_freebsd32, since dtraceall depends on it.
Reviewed by: ed, gnn
Differential Revision: https://reviews.freebsd.org/D13670
The ep(4) driver is the only consumer of the two functions from
elink.c. I removed the standalone module as well, and most likely,
the module metadata is not needed anywhere, but this is for later
cleanup.
Discussed with: imp, jhb
Sponsored by: The FreeBSD Foundation
Initial update to the ixgbe PF and VF drivers to support the iflib interface.
The PF driver version is bumped to 4.0.0, and the VF driver version is bumped to 2.0.0.
Special thanks to sbruno@ for the support in helping make this conversion happen.
Submitted by: Jeb Cramer <cramerj@intel.com>, Krzysztof Galazka (Chris) <krzysztof.galazka@intel.com>, Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Reviewed by: sbruno@, shurd@, #IntelNetworking
Tested by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>, Sergey Kozlov <kozlov.sergey.404@gmail.com>
Sponsored by: Limelight Networks, Intel Corporation
Differential Revision: https://reviews.freebsd.org/D11727
sinovoip-bpi-m3.dts was disconnected from the build in r324822. Since then,
a CCU driver has been added and several other changes have been made to
make us compatible with upstream DTS for this board.
Add links for older DTB that might be used: our u-boot port was expecting
sinovoip-bpi-m3.dtb up until ports r455629, and our u-boot will not be
switching to the upstream name (sun8i-a83t-bananapi-m3) quite yet.
Discussed with: manu
The OBJS_DEPEND_GUESS mechanism was making vmx_genassym.o depend
on all headers along with vmx_assym.h, though vmx_assym.h depends
on having vmx_genassym.o present to generate. Moving the headers
to DPSRCS is enough to resolve the issue as they will no longer
be implicit dependencies for all objects. Because of this we
need explicit OBJS_DEPEND_GUESS entries to ensure the headers
are generated when needed for the *_support.o files that need
them.
X-MFC-With: r326552
MFC after: 2 weeks
Sponsored by: Dell EMC
Currently, bwn(4) relies on the siba_bwn(4) bus driver to provide support
for the on-chip SSB interconnect found in Broadcom's older PCI(e) Wi-Fi
adapters. Non-PCI Wi-Fi adapters, as well as the newer BCMA interconnect
found in post-2009 Broadcom Wi-Fi hardware, are not supported by
siba_bwn(4).
The bhnd(4) bus driver (also used by the FreeBSD/MIPS Broadcom port)
provides a unified kernel interface to a superset of the hardware supported
by siba_bwn; by attaching bwn(4) via bhnd(4), we can support both modern
PCI(e) Wi-Fi devices based on the BCMA backplane interconnect, as well as
Broadcom MIPS WiSoCs that include a D11 MAC core directly attached to their
SSB or BCMA backplane.
This diff introduces opt-in bwn(4) support for bhnd(4) by providing:
- A small bwn(4) driver subclass, if_bwn_bhnd, that attaches via
bhnd(4) instead of siba_bwn(4).
- A bhndb(4)-based PCI host bridge driver, if_bwn_pci, that optionally
probes at a higher priority than the siba_bwn(4) PCI driver.
- A set of compatibility shims that perform translation of bwn(4)'s
siba_bwn function calls into their bhnd(9) API equivalents when bwn(4)
is attached via a bhnd(4) bus parent. When bwn(4) is attached via
siba_bwn(4), all siba_bwn function calls are simply passed through to
their original implementations.
To test bwn(4) with bhnd(4), place the following lines in loader.conf(5):
hw.bwn_pci.preferred="1"
if_bwn_pci_load="YES
bwn_v4_ucode_load="YES"
bwn_v4_lp_ucode_load="YES"
To verify that bwn(4) is using bhnd(4), you can check dmesg:
bwn0: <Broadcom 802.11 MAC/PHY/Radio, rev 15> ... on bhnd0
... or devinfo(8):
pcib2
pci2
bwn_pci0
bhndb0
bhnd0
bwn0
...
bwn(4)/bhnd(4) has been tested for regressions with most chipsets currently
supported by bwn(4), including:
- BCM4312
- BCM4318
- BCM4321
With minimal changes to the DMA code (not included in this commit), I was
also able to test support for newer BCMA devices by bringing up basic
working Wi-Fi on two previously unsupported, BCMA-based N-PHY chipsets:
- BCM43224
- BCM43225
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation & Plausible Labs
Differential Revision: https://reviews.freebsd.org/D13041
This change adds an implementation of a sysent for running CloudABI
armv6 and armv7 binaries on FreeBSD/arm64. It is a somewhat literal copy
of the armv6 version, except that it's been patched up to use the proper
registers.
Just like for cloudabi32.ko on FreeBSD/amd64, we make use of a vDSO that
automatically pads system call parameters to 64-bit value. These are
stored in a buffer on the stack, meaning we need to use copyin() and
copyout() unconditionally.
Very early BHND Wi-Fi devices (e.g. BCM4318) do not support any form of
dynamic clock control; on these devices, any PMU requests that cannot be
met by the device's fixed clock state will return an appropriate error
code.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
This commit merges projects/bsd_rdma_4_9 to head.
List of kernel sources used:
============================
1) kernel sources were cloned from git://github.com/torvalds/linux.git
Top commit 69973b830859bc6529a7a0468ba0d80ee5117826 - tag: v4.9, linux-4.9
2) krping was cloned from https://github.com/larrystevenwise/krping
Top commit 292a2f1abf0348285e678a82264740d52e4dcfe4
List of userspace sources used:
===============================
1) rdma-core was cloned from https://github.com/linux-rdma/rdma-core.git
Top commit d65138ef93af30b3ea249f3a84aa6a24ba7f8a75
2) OpenSM was cloned from git://git.openfabrics.org/~halr/opensm.git
Top commit 85f841cf209f791c89a075048a907020e924528d
3) libibmad was cloned from git://git.openfabrics.org/~iraweiny/libibmad.git
Tag 1.3.13 with some additional patches from Mellanox.
4) infiniband-diags was cloned from git://git.openfabrics.org/~iraweiny/infiniband-diags.git
Tag 1.6.7 with some additional patches from Mellanox.
NOTES:
======
1) The mthca driver has been removed in kernel and in userspace.
2) All GPLv2 only sources have been removed and where applicable
rewritten from scratch under a BSD license.
3) List of fully supported drivers in userspace and kernel:
a) iw_cxgbe (Chelsio)
b) mlx4ib (Mellanox)
c) mlx5ib (Mellanox)
4) WITH_OFED=YES is still required by make in order to build
OFED userspace and kernel code.
5) Full support has been added for routable RoCE, RoCE v2.
Sponsored by: Mellanox Technologies
The recently imported cloudabi_vdso_armv6_on_64bit.S should be the vDSO
for 32-bit processes when being run on FreeBSD/arm64. This vDSO ensures
that all system call arguments are padded to 64 bits, so that they can
be used by the kernel to call into most of the native implementations
directly.
The driver is functional on both BHND Wi-Fi adapters and MIPS SoCs, but
does not currently include support for features not required by bwn(4),
including GPIO interrupt handling.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12708
The bwn(4) driver requires a number of extensions to the bhnd(4) PMU
interface to support external configuration of PLLs, LDOs, and other
parameters that require chipset or PHY-specific workarounds.
These changes add support for:
- Writing raw voltage register values to PHY-specific LDO regulator
registers (required by LP-PHY).
- Enabling/disabling PHY-specific LDOs (required by LP-PHY)
- Writing to arbitrary PMU chipctrl registers (required for common PHY PLL
reset support).
- Requesting chipset/PLL-specific spurious signal avoidance modes.
- Querying clock frequency and latency.
Additionally, rather than updating legacy PWRCTL support to conform to the
new PMU interface:
- PWRCTL API is now provided by a bhnd_pwrctl_if.m interface.
- Since PWRCTL is only found in older SSB-based chipsets, translation from
bhnd(4) bus APIs to corresponding PWRCTL operations is now handled
entirely within the siba(4) driver.
- The PWRCTL-specific host bridge clock gating APIs in bhnd_bus_if.m have
been lifted out into a standalone bhnd_pwrctl_hostb_if.m interface.
Approved by: adrian (mentor, implicit)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12664
the system time.
As we seem to only read this time on boot, and this is the only source of
time on many arm64 machines we need to enable this by default there. As
this is not always the case with U-Boot firmware, or when we have been
booted from a non-UEFI environment we only enable the device driver when
the Runtime Services are present and reading the time doesn't result in an
error.
PR: 212185
Reviewed by: imp, kib
Tested by: emaste
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12650
IPsec support can be loaded as kernel module, thus do not depend from
kernel option IPSEC and always build O_IPSEC opcode implementation as
enabled.
Obtained from: Yandex LLC
MFC after: 1 week
Sponsored by: Yandex LLC
Background:
The coming ibcore update forces an update of mlx4ib(4) which in turn requires
an updated mlx4 core module. This also affects the mlx4en(4) module because
commonly used APIs are updated. This commit is a middle step updating the
mlx4 modules towards the new ibcore.
This change contains no major new features.
Changes in mlx4:
a) Improved error handling when mlx4 PCI devices are
detached inside VMs.
b) Major update of codebase towards Linux 4.9.
Changes in mlx4ib(4):
a) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Changes in mlx4en(4):
a) Update flow steering code in mlx4en to use new APIs for
registering MAC addresses and IP addresses.
b) Update all statistics counters to be 64-bit.
c) Minimal changes needed in order to compile using the
updated mlx4 core APIs.
Sponsored by: Mellanox Technologies
MFC after: 1 week
the coming ibcore and mlx5ib updates in order to support traffic redirection
to so-called raw ethernet QPs.
Remove unused E-switch related routines and files while at it.
Sponsored by: Mellanox Technologies
MFC after: 1 week
mbpool existed to support NICs with memory interfaces and all remaining
comsumers were removed earlier this year with NATM.
Reviewed by: jhb
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D10513
this is more friendly to the tree.
Tested this with loader.conf:if_igb_load="YES" and it does the right
thing.
Submitted by: Ian Lepore <ian@freebsd.org>
mapping. This uses the new common code shared with amd64.
The RTC should only be accessed via EFI. There is no locking around it as
the spec only has this as a requirement for the PC-AT CMOS device.
Reviewed by: kib, imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12595
end up with non-standard DESTDIR information in its symlink. This
can happen very trivially if the release scripts are used.
Sponsored by: Limelight Networks
Changes since 1.16.26.0 for all three firmwares are listed below. This
list was obtained from the Release Notes of the Chelsio Unified Wire
v3.5.05 release for Linux.
T6 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed a fw crash when configured traffic rate limit is less than 10kbps.
- Fixed traffic rate limiting for smaller traffic rate value.
ETH:
- Fixed 40G link failure when interface is toggled.
- Fixed adapter crash when interface is toggled during traffic.
- Fixed 25G link failure when PEER only supports consortium mode autoneg
for 25G.
- Fixed 100G optics link failure when cable is plugged in after bringing up
the interface.
- Enable RS FEC as default if speed is 100G.
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
- Fixed iWARP SRQ reuse failure.
FOiSCSI:
- Fixed vlan interface ping failure.
- Fixed target discovery failures.
- Fixed mutual chap login failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed fw crash caused by MC parity error in SO adapters.
- Generate Timer0Int interrupt if fw crashes due to unaligned access error. Host
driver must look into PCIE_FW register to see if any fw fatal error has
encountered. If PCIE_FW doesn't indicate any error then driver must ignore this
interrupt.
- Fixed receive buffer threshold settings which was resulting in error frames on
receive side.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed improper LED behaviour for blink test and when traffic is running.
- Removed storage of previous fec settings from fw. Driver needs to pass the user
settings whenever a new module is plugged in as fw resets these when a module is
unplugged.
OFLD
- OVS offload: TP cache is flushed periodically to get the accuate filters stats
(hit count).
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- VNI support added for filtering. New entry_type FW_VI_MAC_TYPE_EXACTMAC_VNI
added to FW_VI_MAC_CMD.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
- HMA (Host memory access) support added. New FW_HMA_CMD and
FW_PARAMS_PARAM_DEV_HMA_SIZE added to query and configure the HMA. It
enables the memfree support (256 connections) for iwarp.
- PTP support enabled.
ETH:
- Added consortium mode 50G support.
- Added the ability to allow only selected speeds to be advertised during auto
negotiation.
- Increased port capability from 16 to 32 bits to support more speeds.
FW_PARAMS_PARAM_PFVF_PORT_CAPS32 added to query whether fw supports 16 or 32
bit port capability.
OFLD:
- RDMA Write with immediate support added (iwarp 2.0 feature)
- FW_TLS_KEYCTX_TX_WR removed and security key management moved to driver.
- 256 offloaded connections support for iwarp on SO adapters.
iSCSI:
- New param FW_PARAMS_PARAM_DEV_PPOD_EDRAM added for iscsi ppod configuration
in EDRAM (performance improvement).
FOiSCSI:
- iSCSI Command offload target support added.
FOFCoE:
- FCoE support enabled.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
- Fixed DDR3/DDR4 ECC errors.
- Fixed an FLR issue where FLR completion was going to host before FLR
processing is finished in fw.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
- Fixed false link up when peer interface was brought down.
- Enabling RS FEC by default for 100Gbase-SR4 according to 802.3BJ standard.
- Fixed bugs related to negotiated fec based local/peer fec ability and request.
- Fixed auto-neg failure with few switches.
- T6 Performance improvement fixes.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
- T6 Crypto Coprocessor mode bug fixes.
- T6 Crypto TLS-inline mode bug fixes.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
ETH:
- Added broadcom consortium next page support for 25G CR.
This can be enabled using flags=an_brcm option in the t6-config.txt file.
- Added spider mode support.
- Added support for 10G-BaseT converter sfp+ module.
- Added support for additional 25G/100G cables.
- Added support to enable/disable auto-neg using ethtool.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
Fixes
-----
BASE:
- Fixed DDR4 uncorrectable errors.
ETH:
- Enabled link auto negotiation (AN) by default in config file.
- Added AN and FEC control api. Host driver and application can enable/disable
AN and FEC.
ENHANCEMENTS
------------
BASE:
- Enabled High priorty filter.
- Added T6425 adapter support.
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- Set multiple fec values only if AN is enabled in config file and when module
is connected.
- Fixed intermittent DDR3/4 ECC errors.
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
ETH:
- Made devlog more verbose by printing cable information in redable form.
- Updated AN settings to work with more 25G/100G switches.
- Added support for more SFP28/QSFP28 cables.
- Fixed an issue of link going down after few hours of idle time.
OFLD:
- Fixed an issue in TLS which was causing fw crash on running TLS traffic.
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T5 Firmware
++++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
BASE:
- Fixed offload memory overcommit in case of SO adapter.
ETH:
- Fixed DCBX configuration refresh failure.
OFLD
- Fixed 0B iWARP ingress read failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed an FLR issue which was causing error when VF attached VM was powered on.
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
- Fixed link failure when speed is changed from 10G-1G-10G due to incorrect flag
check.
- Fixed T580 link failure with few switches which take more time for
establishing link.
ENHANCEMENTS
------------
BASE:
- Ring backbone feature added. New FW_PARAMS_PARAM_DEV_RING_BACKBONE param type
added to query and enable ring backbone support.
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer group
mapping for the ports.
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
FOiSCSI:
- iSCSI Command offload target support added.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
- Fixed the link failure when optical cable is inserted into the QSA module
after loading the driver.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
================================================================================
Version : 1.16.33.0
Date : 02/24/2017
================================================================================
ENHANCEMENTS
------------
ETH:
- Added new workrequest ETH_TX_PKTS2_WR (see fw api document for more details).
================================================================================
Version : 1.16.29.0
Date : 01/27/2017
================================================================================
FIXES
-----
BASE:
- max number of ethctrl queue in VF set to 2 (reverted the last change
because it causes problem in VF drivers).
FOiSCSI:
- Fixed the failure of PXE boot OS install on an iscsi lun.
ENHANCEMENTS
------------
OFLD:
- Added filtering support for NAT. New WR FW_FILTER2_WR and
FW_PARAMS_PARAM_DEV_FILTER2_WR added for the same.
- Added RDMA guest mode (mode 3 or RDMA from VF) support.
================================================================================
T4 Firmware
+++++++++++
================================================================================
Version : 1.16.63.0
Date : 09/29/2017
================================================================================
Fixes
-----
ETH:
- Fixed DCBX configuration refresh failure.
FOiSCSI:
- Fixed vlan interface ping failure.
================================================================================
Version : 1.16.59.0
Date : 09/05/2017
================================================================================
FIXES
-----
ETH:
- Fixed an issue in connection traffic shaping when
FLOWC_WR->FW_FLOWC_MNEM_SCHEDCLASS is not received in first WR on the connection.
ENHANCEMENTS
------------
BASE:
- FW_PARAMS_PARAM_DEV_TPCHMAP API added to read the port to channel mapping.
================================================================================
Version : 1.16.43.0
Date : 05/05/2017
================================================================================
FIXES
-----
BASE:
- Fixed default DCB mode to AUTO.
- Fixed DCBX bugs when AUTO mode is configured in config file.
- Fixed an issue where even after removing PFC from switch, PFC wasn't getting
reset.
ETH:
- Fixed bug in writing multi-bytes using i2c interface.
OFLD
- Fixed an extra credit issue if FW_RI_TYPE_FINI is delayed in fw due to
backpressure.
- Added a new queue type FW_IQ_TYPE_VF_CQ to handle the FW_PARAMS_PARAM_DMAQ*
commands. queue type will be part of the FW_PARAMS_PARAM_DMAQ_IQ_INTIDX
value. Used in guest RDMA (RDMA from VM/VF) usecase.
ENHANCEMENTS
------------
BASE:
- Added new API FW_PARAM_PARAM_DEV_MPSBGMAP to read the priority to buffer
group mapping for the ports.
Obtained from: Chelsio Communications
MFC after: 2 weeks
Sponsored by: Chelsio Communications
Make armv7 as a new MACHINE_ARCH.
Copy all the places we do armv6 and add armv7 as basically an
alias. clang appears to generate code for armv7 by default. armv7 hard
float isn't supported by the the in-tree gcc, so it hasn't been
updated to have a new default.
Support armv7 as a new valid MACHINE_ARCH (and by extension
TARGET_ARCH).
Add armv7 to the universe build.
Differential Revision: https://reviews.freebsd.org/D12010
machine independent parts of the existing code to a new file that can be
shared between amd64 and arm64.
Reviewed by: kib (previous version), imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D12434
7431 ZFS Channel Programs
illumos/illumos-gate@dfc115332cdfc115332chttps://www.illumos.org/issues/7431
ZFS channel programs (ZCP) adds support for performing compound ZFS
administrative actions via Lua scripts in a sandboxed environment (with time
and memory limits).
This initial commit includes both base support for running ZCP scripts, and a
small initial library of API calls which support getting properties and
listing, destroying, and promoting datasets.
Testing: in addition to the included unit tests, channel programs have been in
use at Delphix for several months for batch destroying filesystems. The
dsl_destroy_snaps_nvl() call has also been replaced with
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: Chris Williamson <chris.williamson@delphix.com>
8552 ZFS LUA code uses floating point math
illumos/illumos-gate@916c8d8811916c8d8811https://www.illumos.org/issues/8552
In the LUA interpreter used by "zfs program", the lua format() function
accidentally includes support for '%f' and friends, which can cause compilation
problems when building on platforms that don't support floating-point math in
the kernel (e.g. sparc). Support for '%f' friends (%f %e %E %g %G) should be
removed, since there's no way to supply a floating-point value anyway (all
numbers in ZFS LUA are int64_t's).
Reviewed by: Yuri Pankov <yuripv@gmx.com>
Reviewed by: Igor Kozhukhov <igor@dilos.org>
Approved by: Dan McDonald <danmcd@joyent.com>
Author: Matthew Ahrens <mahrens@delphix.com>
8590 memory leak in dsl_destroy_snapshots_nvl()
illumos/illumos-gate@e6ab4525d1e6ab4525d1https://www.illumos.org/issues/8590
In dsl_destroy_snapshots_nvl(), "snaps_normalized" is not freed after it is
added to "arg".
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Steve Gonczi <steve.gonczi@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Author: Matthew Ahrens <mahrens@delphix.com>
FreeBSD notes:
- zfs-program.8 manual page is taken almost as is from the vendor repository,
no FreeBSD-ification done
- fixed multiple instances of NULL being used where an integer is expected
- replaced ETIME and ECHRNG with ETIMEDOUT and EDOM respectively
This commit adds a modified version of Lua 5.2.4 under
sys/cddl/contrib/opensolaris/uts/common/fs/zfs/lua, mirroring the
upstream. See README.zfs in that directory for the description of Lua
customizations.
See zfs-program.8 on how to use the new feature.
MFC after: 5 weeks
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D12528
parser.
This allows us to use the EROM parser API in cases where the standard bus
space I/O APIs are unsuitable. In particular, this will allow us to parse
the device enumeration table directly from bhndb(4) drivers, prior to
full attach and configuration of the bridge.
Approved by: adrian (mentor)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D12510
Some x86 class CPUs have accelerated intrinsics for SHA1 and SHA256.
Provide this functionality on CPUs that support it.
This implements CRYPTO_SHA1, CRYPTO_SHA1_HMAC, and CRYPTO_SHA2_256_HMAC.
Correctness: The cryptotest.py suite in tests/sys/opencrypto has been
enhanced to verify SHA1 and SHA256 HMAC using standard NIST test vectors.
The test passes on this driver. Additionally, jhb's cryptocheck tool has
been used to compare various random inputs against OpenSSL. This test also
passes.
Rough performance averages on AMD Ryzen 1950X (4kB buffer):
aesni: SHA1: ~8300 Mb/s SHA256: ~8000 Mb/s
cryptosoft: ~1800 Mb/s SHA256: ~1800 Mb/s
So ~4.4-4.6x speedup depending on algorithm choice. This is consistent with
the results the Linux folks saw for 4kB buffers.
The driver borrows SHA update code from sys/crypto sha1 and sha256. The
intrinsic step function comes from Intel under a 3-clause BSDL.[0] The
intel_sha_extensions_sha<foo>_intrinsic.c files were renamed and lightly
modified (added const, resolved a warning or two; included the sha_sse
header to declare the functions).
[0]: https://software.intel.com/en-us/articles/intel-sha-extensions-implementations
Reviewed by: jhb
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12452
other kernel infrastructure changes.
Note that this doesn't affect the base cxgb(4) NIC driver for T3 at all.
MFC after: No MFC.
Sponsored by: Chelsio Communications
This module is specific to a single Marvel board that we currently
only support in 64-bit mode. Remove it from the build otherwise. It
likely should be completely removed, but this unbreaks x86 building.
Noticed by: sbruno@
This patch adds support for UART in Armada 3700 family.
It exposes both low-level UART interface, as well as
standard driver methods.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12250
Turn on the required options in the ERL config file, and ensure
that the fbt module is listed as a dependency for mips in
the modules/dtrace/dtraceall/dtraceall.c file.
PR: 220346
Reviewed by: gnn, markj
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D12227
AMD Family 17h CPUs have an internal network used to communicate between
the host CPU and the PSP and SMU coprocessors. It exposes a simple
32-bit register space.
Reviewed by: avg (no +1), mjoras, truckman
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12217
This driver supports both NTB-to-NTB and NTB-to-Root Port modes (though
the second with predictable complications on hot-plug and reboot events).
I tested it with PEX 8717 and PEX 8733 chips, but expect it should work
with many other compatible ones too. It supports up to two NT bridges
per chip, each of which can have up to 2 64-bit or 4 32-bit memory windows,
6 or 12 scratchpad registers and 16 doorbells. There are also 4 DMA engines
in those chips, but they are not yet supported.
While there, rename Intel NTB driver from generic ntb_hw(4) to more specific
ntb_hw_intel(4), so now it is on par with this new ntb_hw_plx(4) driver and
alike to Linux naming.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
These firmwares come from a pre-release snapshot. The final firmwares
in this Chelsio release cycle will likely be .61.0 or later and those
will be the next "long lived" firmwares in FreeBSD head and stable
branches. .59 is being provided in head (only) for wider test exposure.
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
Remote DMA over Converged Ethernet, RoCE, for the ConnectX-4 series of
PCI express network cards.
There is currently no user-space support and this driver only supports
kernel side non-routable RoCE V1. The krping kernel module can be used
to test this driver. Full user-space support including RoCE V2 will be
added as part of the ongoing upgrade to ibcore from Linux 4.9. Otherwise
this driver is feature equivalent to mlx4ib(4). The mlx5ib(4) kernel
module will only be built when WITH_OFED=YES is specified.
MFC after: 2 weeks
Sponsored by: Mellanox Technologies
sysctls to display stats, stats polled every 2 seconds
Modify QLA_LOCK()/QLA_UNLOCK() to not sleep after acquiring mtx_lock
Add support to turn OFF/ON error recovery following heartbeat failure for
debug purposes.
Set default max values to 32 Tx/Rx/SDS rings
MFC after:5 days
Using latest U-Boot for RPI 1 or 2 the DTB loaded by the firmware is discarded.
The DTB was previously patched by the firmware to contain the DMA channel mask.
DTB provided by the rpi firmware or DTS in the Linux tree contain the raw value
directly. Do the same for our DTS as we cannot switch to the upstream ones yet.
Not having the DMA channel mask setup properly cause mmc not to be detected
(and probably other problems on driver using DMA).
Also, add links for rpi dtb to the name used by u-boot. This way the dtb can be
loaded by ubldr using the U-Boot env variable fdtfile.
Tested On: RPI B Rev2, RPI Zero, RPI 2 v1.1 RPI 2 v1.2
Thanks to Sylvain Garrigues <sylvain@sylvaingarrigues.com> for the help.
PR: 218344
Intel SGX allows to manage isolated compartments "Enclaves" in user VA
space. Enclaves memory is part of processor reserved memory (PRM) and
always encrypted. This allows to protect user application code and data
from upper privilege levels including OS kernel.
This includes SGX driver and optional linux ioctl compatibility layer.
Intel SGX SDK for FreeBSD is also available.
Note this requires support from hardware (available since late Intel
Skylake CPUs).
Many thanks to Robert Watson for support and Konstantin Belousov
for code review.
Project wiki: https://wiki.freebsd.org/Intel_SGX.
Reviewed by: kib
Relnotes: yes
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D11113
- Add FDT probe code.
- Do i2c transfers with exclusive bus ownership.
- Use config_intrhook_oneshot() to defer chip setup because some i2c
busses can't do transfers without interrupts.
- Add a detach() routine.
- Add to module build.
This driver supports only basic timekeeping functionality. It completely
replaces the ds133x driver. It can also replace the ds1374 driver, but that
will take a few other changes in MIPS code and config, and will be committed
separately. It does NOT replace the existing ds1307 driver, which provides
access to some of the extended features on the 1307 chip, such as controlling
the square wave output signal. If both ds1307 and ds13rtc drivers are
present, the ds1307 driver will outbid and win control of the device.
This driver can be configured with FDT data, or by using hints on non-FDT
systems. In addition to the standard hints for i2c devices, it requires
a "chiptype" string of the form "dallas,ds13xx" where 'xx' is the chip id
(i.e., the same format as FDT compat strings).
TCP connections (order of tens of thousands), with predominantly Transmits.
Choice to perform receive operations either in IThread or Taskqueue Thread.
Submitted by:Vaishali.Kulkarni@cavium.com
MFC after:5 days
o Replace __riscv64 with (__riscv && __riscv_xlen == 64)
This is required to support new GCC 7.1 compiler.
This is compatible with current GCC 6.1 compiler.
RISC-V is extensible ISA and the idea here is to have built-in define
per each extension, so together with __riscv we will have some subset
of these as well (depending on -march string passed to compiler):
__riscv_compressed
__riscv_atomic
__riscv_mul
__riscv_div
__riscv_muldiv
__riscv_fdiv
__riscv_fsqrt
__riscv_float_abi_soft
__riscv_float_abi_single
__riscv_float_abi_double
__riscv_cmodel_medlow
__riscv_cmodel_medany
__riscv_cmodel_pic
__riscv_xlen
Reviewed by: ngie
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D11901
debug (cudbg) code, hooked up to the main driver via an ioctl.
The ioctl can be used to collect the chip's internal state in a
compressed dump file. These dumps can be decoded with the "view"
component of cudbg.
Obtained from: Chelsio Communications
MFC after: 2 months
Sponsored by: Chelsio Communications
Propagate warning flags from kern.opts.mk and then fix minor -Werror
issues when building with gcc from -Wredundant-decls, -Wnested-externs,
-Wuninitialized.
Reviewed by: davidcs
Approved by: markj (mentor)
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D11413
This also avoids compiling in pci_iov support into the kernel if_ixoif
the PCI_IOV option is disabled.
Reviewed by: rstone
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D11573
This emulated device attaches to the ISA bus and registers itself as
HBA supporting MMC/SD cards. This allows to develop and test MMC XPT
and MMC / SDIO peripheral drivers even in the VM such as bhyve.
Submitted by: Ilya Babulin
Implement the MMC/SD/SDIO protocol within a CAM framework. CAM's
flexible queueing will make it easier to write non-storage drivers
than the legacy stack. SDIO drivers from both the kernel and as
userland daemons are possible, though much of that functionality will
come later.
Some of the CAM integration isn't complete (there are sleeps in the
device probe state machine, for example), but those minor issues can
be improved in-tree more easily than out of tree and shouldn't gate
progress on other fronts. Appologies to reviews if specific items
have been overlooked.
Submitted by: Ilya Bakulin
Reviewed by: emaste, imp, mav, adrian, ian
Differential Review: https://reviews.freebsd.org/D4761
merge with first commit, various compile hacks.
Includes:
- Support for X550EM devices.
- Support for Bypass adapters.
- Flow Director code moved to separate files
- SR-IOV code moved to separate files
- Netmap code moved to separate files
Differential Revision: https://reviews.freebsd.org/D11232
Submitted by: Jeb Cramer <cramerj@intel.com>
Reviewed by: erj@
Tested by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Sponsored by: Intel Corporation
This patch was inspired by an opposite change made to shrink the code
for the boot loader.
On my i7-4770, it increases the skein1024 speed from 470 to 550 MB/s
Reviewed by: sbruno
MFC after: 1 month
Sponsored by: ScaleEngine Inc.
Differential Revision: https://reviews.freebsd.org/D7824
H2+ SoC is a stripped down version of H3 without gigabit ethernet and 4K HDMI.
Also add sun8i-h2-plus-orangepi-zero.dts to the build as we run on this board.
From the linux tune2fs(8) manpage:
"Allow the kernel to initialize bitmaps and inode tables and keep a high
watermark for the unused inodes in a filesystem, to reduce e2fsck(8) time.
This first e2fsck run after enabling this feature will take the full time,
but subsequent e2fsck runs will take only a fraction of the original time,
depending on how full the file system is."
Submitted by: Fedor Uporov
Differential Revision: https://reviews.freebsd.org/D11211
This patch currently supports:
- ibcore as a kernel module only
- krping as a kernel module only
- ipoib as a kernel module only
Sponsored by: Mellanox Technologies
In particular:
- Don't evaluate event conditions with a sleepqueue lock held, since such
code may attempt to acquire arbitrary locks.
- Fix the return value for wait_event_interruptible() in the case that the
wait is interrupted by a signal.
- Implement wait_on_bit_timeout() and wait_on_atomic_t().
- Implement some functions used to test for pending signals.
- Implement a number of wait_event_*() variants and unify the existing
implementations.
- Unify the mechanism used by wait_event_*() and schedule() to put the
calling thread to sleep.
This is required to support updated DRM drivers. Thanks to hselasky for
finding and fixing a number of bugs in the original revision.
Reviewed by: hselasky
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10986
Its purpose was to translate the values for msdosfs inode numbers,
which is calculated from the msdosfs structures describing the file,
into the range representable by 32bit ino_t. The translation acted
for filesystems larger than 128Gb, it reserved the range 0xf0000000
(FILENO_FIRST_DYN) to UINT32_MAX and remembered some arbitrary
translation of ino >= FILENO_FIRST_DYN into this range. It consumed
memory that could be only freed by unmount, and the translation was
not stable across remounts.
With ino_t type extended to 64 bit, there is no such issue and values
can be returned without compaction to 32bit. That is, for the native
environments, the translation layer is not necessary and adds
significant undeserved code complexity. For compat ABIs which use
32bit ino_t, the vfs.ino64_trunc_error sysctl provides some measures
to soften the failure mode when inode numbers truncation is not safe.
Discussed with: bde
Sponsored by: The FreeBSD Foundation
* This change also fixes a possible issue in the existing smart-fifo code,
which set the IWM_SF_CFG_DUMMY_NOTIF_OFF bit on AC8260 chipsets, although
that's only used in iwlwifi for Family 8000 chipsets connected via SDIO
interface.
Obtained from: Dragonflybsd.git cb650b01526b0aeef3c4307d926e7f1428997d50
This is closely tied to the Extended Attribute implementation.
Submitted by: Fedor Uporov
Reviewed by: kevlo, pfg
Differential Revision: https://reviews.freebsd.org/D10807
were copied to the buffer supplied by the user.
Also fix getrandom() if Linuxulator modules are built without the kernel.
PR: 219464
Submitted by: Maciej Pasternacki
Reported by: Maciej Pasternacki
MFC after: 1 week
In the deep past, when this code compiled as a binary module, ath_hal
built as a module. This allowed custom, smaller HAL modules to be built.
This was especially beneficial for small embedded platforms where you
didn't require /everything/ just to run.
However, sometime around the HAL opening fanfare, the HAL landed here
as one big driver+HAL thing, and a lot of the (dirty) infrastructure
(ie, #ifdef AH_SUPPORT_XXX) to build specific subsets of the HAL went away.
This was retained in sys/conf/files as "ath_hal_XXX" but it wasn't
really floated up to the modules themselves.
I'm now in a position where for the reaaaaaly embedded boards (both the
really old and the last couple generation of QCA MIPS boards) having a
cut down HAL module and driver loaded at runtime is /actually/ beneficial.
This reduces the kernel size down by quite a bit. The MIPS modules look
like this:
adrian@gertrude:~/work/freebsd/head-embedded/src % ls -l ../root/mips_ap/boot/kernel.CARAMBOLA2/ath*ko
-r-xr-xr-x 1 adrian adrian 5076 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_dfs.ko
-r-xr-xr-x 1 adrian adrian 100588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal.ko
-r-xr-xr-x 1 adrian adrian 627324 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_hal_ar9300.ko
-r-xr-xr-x 1 adrian adrian 314588 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_main.ko
-r-xr-xr-x 1 adrian adrian 23472 May 23 23:45 ../root/mips_ap/boot/kernel.CARAMBOLA2/ath_rate.ko
And the x86 versions, like this:
root@gertrude:/home/adrian # ls -l /boot/kernel/ath*ko
-r-xr-xr-x 1 root wheel 36632 May 24 18:32 /boot/kernel/ath_dfs.ko
-r-xr-xr-x 1 root wheel 134440 May 24 18:32 /boot/kernel/ath_hal.ko
-r-xr-xr-x 1 root wheel 82320 May 24 18:32 /boot/kernel/ath_hal_ar5210.ko
-r-xr-xr-x 1 root wheel 104976 May 24 18:32 /boot/kernel/ath_hal_ar5211.ko
-r-xr-xr-x 1 root wheel 236144 May 24 18:32 /boot/kernel/ath_hal_ar5212.ko
-r-xr-xr-x 1 root wheel 336104 May 24 18:32 /boot/kernel/ath_hal_ar5416.ko
-r-xr-xr-x 1 root wheel 598336 May 24 18:32 /boot/kernel/ath_hal_ar9300.ko
-r-xr-xr-x 1 root wheel 406144 May 24 18:32 /boot/kernel/ath_main.ko
-r-xr-xr-x 1 root wheel 55352 May 24 18:32 /boot/kernel/ath_rate.ko
.. so you can see, not building the whole HAL can save quite a bit.
For example, if you don't need AR9300 support, you can actually avoid
wasting half a megabyte of RAM. On embedded routers this is quite a
big deal.
The AR9300 HAL can be later further shrunk because, hilariously,
it indeed supports AH_SUPPORT_<xxx> for optionally adding chipset support.
(I'll chase that down later as it's quite a big savings if you're only
building for a single embedded target.)
So:
* Create a very hackish way to load/unload HAL modules
* Create module metadata for each HAL subtype - ah_osdep_arXXXX.c
* Create module metadata for ath_rate and ath_dfs (bluetooth is
currently just built as part of it)
* .. yes, this means we could actually build multiple rate control
modules and pick one at load time, but I'd rather just glue this
into net80211's rate control code. Oh well, baby steps.
* Main driver is now "ath_main"
* Create an "if_ath" module that does what the ye olde one did -
load PCI glue, main driver, HAL and all child modules.
In this way, if you have "if_ath_load=YES" in /boot/modules.conf
it will load everything the old way and stuff should still work.
* For module autoloading purposes, I actually /did/ fix up
the name of the modules in if_ath_pci and if_ath_ahb.
If you want to selectively load things (eg on ye cheape ARM/MIPS platforms
where RAM is at a premium) you should:
* load ath_hal
* load the chip modules in question
* load ath_rate, ath_dfs
* load ath_main
* load if_ath_pci and/or if_ath_ahb depending upon your particular
bus bind type - this is where probe/attach is done.
TODO:
* AR5312 module and associated pieces - yes, we have the SoC side support
now so the wifi support would be good to "round things out";
* Just nuke AH_SUPPORT_AR5416 for now and always bloat the packet
structures; this'll simplify other things.
* Should add a simple refcnt thing to the HAL RF/chip modules so you
can't unload them whilst you're using them.
* Manpage updates, UPDATING if appropriate, etc.
The latest firmware has a number of link related fixes, support for a
new custom card, and the fix for a bug that affected rate limiting on
FreeBSD.
Obtained from: Chelsio Communications
MFC after: 1 week
Sponsored by: Chelsio Communications
ENA is a networking interface designed to make good use of modern CPU
features and system architectures.
The ENA device exposes a lightweight management interface with a
minimal set of memory mapped registers and extendable command set
through an Admin Queue.
The driver supports a range of ENA devices, is link-speed independent
(i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc.), and has
a negotiated and extendable feature set.
Some ENA devices support SR-IOV. This driver is used for both the
SR-IOV Physical Function (PF) and Virtual Function (VF) devices.
ENA devices enable high speed and low overhead network traffic
processing by providing multiple Tx/Rx queue pairs (the maximum number
is advertised by the device via the Admin Queue), a dedicated MSI-X
interrupt vector per Tx/Rx queue pair, and CPU cacheline optimized
data placement.
The ENA driver supports industry standard TCP/IP offload features such
as checksum offload and TCP transmit segmentation offload (TSO).
Receive-side scaling (RSS) is supported for multi-core scaling.
The ENA driver and its corresponding devices implement health
monitoring mechanisms such as watchdog, enabling the device and driver
to recover in a manner transparent to the application, as well as
debug logs.
Some of the ENA devices support a working mode called Low-latency
Queue (LLQ), which saves several more microseconds. This feature will
be implemented for driver in future releases.
Submitted by: Michal Krawczyk <mk@semihalf.com>
Jakub Palider <jpa@semihalf.com>
Jan Medala <jan@semihalf.com>
Obtained from: Semihalf
Sponsored by: Amazon.com Inc.
Differential revision: https://reviews.freebsd.org/D10427
This will help Jenkins dedupe 9 warnings between the static build and
the module build of ipsec(4).
Missed in SRCTOP conversion in r314651.
MFC with: r314651
Sponsored by: Dell EMC Isilon
The ccr(4) driver supports use of the crypto accelerator engine on
Chelsio T6 NICs in "lookaside" mode via the opencrypto framework.
Currently, the driver supports AES-CBC, AES-CTR, AES-GCM, and AES-XTS
cipher algorithms as well as the SHA1-HMAC, SHA2-256-HMAC, SHA2-384-HMAC,
and SHA2-512-HMAC authentication algorithms. The driver also supports
chaining one of AES-CBC, AES-CTR, or AES-XTS with an authentication
algorithm for encrypt-then-authenticate operations.
Note that this driver is still under active development and testing and
may not yet be ready for production use. It does pass the tests in
tests/sys/opencrypto with the exception that the AES-GCM implementation
in the driver does not yet support requests with a zero byte payload.
To use this driver currently, the "uwire" configuration must be used
along with explicitly enabling support for lookaside crypto capabilities
in the cxgbe(4) driver. These can be done by setting the following
tunables before loading the cxgbe(4) driver:
hw.cxgbe.config_file=uwire
hw.cxgbe.cryptocaps_allowed=-1
MFC after: 1 month
Relnotes: yes
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D10763
2. Use sysctls for TRACE_LRO_CNT and TRACE_TSO_PKT_LEN
3. remove unused mtx tx_lock
4. bind taskqueue kernel thread to the appropriate cpu core
5. when tx_ring is full, stop further transmits till at least 1/16th of the Tx Ring is empty. In our case 1K entries. Also if there are rx_pkts to process, put the taskqueue thread to sleep for 100ms, before enabling interrupts.
6. Use rx_pkt_threshold of 128.
MFC after:3 days
* This adds iwm_mvm_rm_sta(), which will be used to tear down firmware
state for better/cleaner iwm_newstate() handling.
* Makes iwm_enable_txq() and iwm_mvm_flush_tx_path() non-static, add
the declarations to if_iwm_util.h for now.
Obtained from: dragonflybsd.git 85d1c6190c4c3564b1a347f253e823aa95c202b2
For GEN1 Hyper-V, vmbus is attached to pcib0, which contains the
resources for PCI passthrough and SR-IOV. There is no
acpi_syscontainer0 on GEN1 Hyper-V.
For GEN2 Hyper-V, vmbus is attached to acpi_syscontainer0, which
contains the resources for PCI passthrough and SR-IOV. There is
no pcib0 on GEN2 Hyper-V.
The ACPI VMBUS device now only holds its _CRS, which is empty as
of this commit; its existence is mainly for upward compatibility.
Device tree structure is suggested by jhb@.
Tested-by: dexuan@
Collabrated-wth: dexuan@
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D10565
the TOE. For now this capability is always enabled in kernels with
options RATELIMIT. t4_tom will check if_capenable once the base driver
gets code to support rate limiting for any socket (TOE or not).
This was tested with iperf3 and netperf ToT as they already support
SO_MAX_PACING_RATE sockopt. There is a bug in firmwares prior to
1.16.45.0 that affects the BSD driver only and results in rate-limiting
at an incorrect rate. This will resolve by itself as soon as 1.16.45.0
or later firmware shows up in the driver.
Relnotes: Yes
Sponsored by: Chelsio Communications
- Create a new file, t4_sched.c, and move all of the code related to
traffic management from t4_main.c and t4_sge.c to this file.
- Track both Channel Rate Limiter (ch_rl) and Class Rate Limiter (cl_rl)
parameters in the PF driver.
- Initialize all the cl_rl limiters with somewhat arbitrary default
rates and provide routines to update them on the fly.
- Provide routines to reserve and release traffic classes.
MFC after: 1 month
Sponsored by: Chelsio Communications
patm(4) devices.
Maintaining an address family and framework has real costs when we make
infrastructure improvements. In the case of NATM we support no devices
manufactured in the last 20 years and some will not even work in modern
motherboards (some newer devices that patm(4) could be updated to
support apparently exist, but we do not currently have support).
With this change, support remains for some netgraph modules that don't
require NATM support code. It is unclear if all these should remain,
though ng_atmllc certainly stands alone.
Note well: FreeBSD 11 supports NATM and will continue to do so until at
least September 30, 2021. Improvements to the code in FreeBSD 11 are
certainly welcome.
Reviewed by: philip
Approved by: harti
FDC_DEBUG is not referenced in any c or header files but traces of it
still remain in other files.
PR: 105608
Reported by: Eugene Grosbein <ports AT grosbein DOT net>
Reviewed by: imp
Approved by: bcr (mentor)
MFC after: 7 days
Differential Revision: https://reviews.freebsd.org/D10303
- Move all bitmap related functions from bitops.h to bitmap.h, similar
to what Linux does.
- Apply some minor code cleanup and simplifications to optimize the
generated code when using static inline functions.
- Implement the following list of bitmap functions which are needed by
drm-next and ibcore:
- bitmap_find_next_zero_area_off()
- bitmap_find_next_zero_area()
- bitmap_or()
- bitmap_and()
- bitmap_xor()
- Add missing include directives to the qlnxe driver
(davidcs@ has been notified)
MFC after: 1 week
Sponsored by: Mellanox Technologies
DTrace includes assym.s, to build this we build assym.o, however
this is unneeded as assym.s only contains macros.
Remove the need to build this by removing it from OBJS, but keep assym.s
in the module dependencies via DPSRCS.
This fixes the build when there is no assembler, e.g. on arm64 without
the external binutils.
Submitted by: andrew
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D10041
The module is designed for modification of a packets of any protocols.
For now it implements only TCP MSS modification. It adds the external
action handler for "tcp-setmss" action.
A rule with tcp-setmss action does additional check for protocol and
TCP flags. If SYN flag is present, it parses TCP options and modifies
MSS option if its value is greater than configured value in the rule.
Then it adjustes TCP checksum if needed. After handling the search
continues with the next rule.
Obtained from: Yandex LLC
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Yandex LLC
No objection from: #network
Differential Revision: https://reviews.freebsd.org/D10150
The goal of this work is to remove the explicit dependency for ctl(4)
on iscsi(4), so end-users without iscsi(4) support in the kernel can
use ctl(4) for its other functions.
This allows those without iscsi(4) support built into the kernel to use
ctl(4) as a test mechanism. As a sidenote, this was possible around the
10.0-RELEASE period, but made impossible for end-users without iscsi(4)
between 10.0-RELEASE and 11.0-RELEASE.
Automatically load cfiscsi(4) from ctladm(8) and ctld(8) for backwards
compatibility with previously releases. The automatic loading feature is
compiled into the beforementioned tools if MK_ISCSI == yes when building
world.
Add a manpage for cfiscsi(4) and refer to it in ctl(4).
Differential Revision: D10099
MFC after: 2 months
Relnotes: yes
Reviewed by: mav, trasz
Sponsored by: Dell EMC Isilon
instrument security event auditing rather than relying on conventional BSM
trail files or audit pipes:
- Add a set of per-event 'commit' probes, which provide access to
particular auditable events at the time of commit in system-call return.
These probes gain access to audit data via the in-kernel audit_record
data structure, providing convenient access to system-call arguments and
return values in a single probe.
- Add a set of per-event 'bsm' probes, which provide access to particular
auditable events at the time of BSM record generation in the audit
worker thread. These probes have access to the in-kernel audit_record
data structure and BSM representation as would be written to a trail
file or audit pipe -- i.e., asynchronously in the audit worker thread.
DTrace probe arguments consist of the name of the audit event (to support
future mechanisms of instrumenting multiple events via a single probe --
e.g., using classes), a pointer to the in-kernel audit record, and an
optional pointer to the BSM data and its length. For human convenience,
upper-case audit event names (AUE_...) are converted to lower case in
DTrace.
DTrace scripts can now cause additional audit-based data to be collected
on system calls, and inspect internal and BSM representations of the data.
They do not affect data captured in the audit trail or audit pipes
configured in the system. auditd(8) must be configured and running in
order to provide a database of event information, as well as other audit
configuration parameters (e.g., to capture command-line arguments or
environmental variables) for the provider to operate.
Reviewed by: gnn, jonathan, markj
Sponsored by: DARPA, AFRL
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D10149
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
They cannot be used anymore with the userland bits we provide.
Furthermore, their KMS versions support the same hardware.
Submitted by: dumbbell
Reviewed by: emaste, manu
Sponsored by: AsiaBSDCon
Differential Revision: https://reviews.freebsd.org/D5614
When locking a mutex and deadlock is detected the first mutex lock
call that sees the deadlock will return -EDEADLK .
MFC after: 1 week
Sponsored by: Mellanox Technologies
spigen provides userland API to SPI bus. Make it available as a loadable
module so people using official ARM images can enabled it on devices like
BBB or RPi without re-building kernel
MFC after: 1 week
Put large functions into linux_slab.c instead of declaring them static
inline.
Add support for more memory allocation wrappers like kmalloc_array()
and __vmalloc().
Make sure either the M_WAITOK or the M_NOWAIT flag is set and mask
away unused memory allocation flags before calling FreeBSD's malloc()
routine.
Move kmalloc_node() definition to slab.h where it belongs.
Implement support for the SLAB_DESTROY_BY_RCU feature when creating a
kmem_cache which basically means kmem_cache memory is freed using
call_rcu().
MFC after: 1 week
Sponsored by: Mellanox Technologies
The module uses unnamed structure and union fields and base GCC in
stable/10 doesn't like it.
I think that that is a C11 feature, so it is courteous of more modern
compilers to not complain about it when compiling in C99 mode.
Approved by: davidcs
MFC after: 5 days
This change makes the workqueue implementation behave more like in
Linux, both functionality wise and structure wise.
All workqueue code has been moved to linux_work.c
Add an atomic based statemachine to the work_struct to ensure proper
operation. Prior to this change struct_work was directly mapped to a
FreeBSD task. When a taskqueue has multiple threads the same task may
end up being executed on more than one worker thread simultaneously.
This might cause problems with code coming from Linux, which expects
serial behaviour, similar to Linux tasklets.
Move all global workqueue function names into the linux_xxx domain to
avoid symbol name clashes in the future.
Implement a few more workqueue related functions and macros.
Create two multithreaded taskqueues for the LinuxKPI during module
load, one for time-consuming callbacks and one for non-time consuming
callbacks.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This interface has no in-tree consumers and has been more or less
non-functional for several releases.
Remove manpage note that the procfs special file 'mem' is grouped to
kmem. This hasn't been true since r81107.
Remove procfs' README file. It is an out of date duplication of the manpage
(quoth the README: "since the bsd kernel is single-processor...").
Reviewed by: vangyzen, bcr (manpage)
Approved by: des (procfs maintainer), vangyzen (mentor)
Differential Revision: https://reviews.freebsd.org/D9802
I imagine that the module would be useful only to a very limited number
of developers, so that's my excuse for not writing any documentation.
On a more serious note, please see DRAM Error Injection section of BKDGs
for families 10h - 16h. E.g. section 2.13.3.1 of BKDG for AMD Family 15h
Models 00h-0Fh Processors.
Many thanks to kib for his suggestions and comments.
Discussed with: kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9824
Add opt_platform.h and opt_acpi.h to the dependencies so modules can be
built as a part of buildworld when MODULES_WITH_WORLD is set
Reported by: Andre Albsmeier (for 11-stable)
MFC after: 1 day
* Uses the IWM_FW_PAGING_BLOCK_CMD firmware command to tell the firmware
what memory ranges to use for paging.
Obtained from: dragonflybsd.git 8a5b199964f8e7bdb00039f0b48817a01b402f18
Add if_iwm_7000.c/if_iwm_8000.c to SRCS to match similar additions made
to sys/conf/files after refactoring done in the commit noted.
PR: 217308
Pointyhat to: adrian
Submitted by: Andreas Nilsson <andrnils@gmail.com>
Reported by: Jakob Alvermark <jakob@alvermark.net>, Juan Ramómon Molina Menor <listjm@club.fr>
Sponsored by: Dell EMC Isilon
When allocating unmapped pages, take advantage of the direct map on
AMD64 to get the virtual address corresponding to a page. Else all
pages allocated must be mapped because sometimes the virtual address
of a page is requested.
Move all page allocation and deallocation code into an own C-file.
Add support for GFP_DMA32, GFP_KERNEL, GFP_ATOMIC and __GFP_ZERO
allocation flags.
Make a clear separation between mapped and unmapped allocations.
Obtained from: kmacy @
MFC after: 1 week
Sponsored by: Mellanox Technologies
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
The build process generates *assym.h using nm from *genassym.o (which is
in turn created from *genassym.c).
When compiling with link-time optimization (LTO) using -flto, .o files
are LLVM bitcode, not ELF objects. This is not usable by genassym.sh,
so remove -flto from those ${CC} invocations.
Submitted by: George Rimar
Reviewed by: dim
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D9659
Tasklets are implemented using a taskqueue and a small statemachine on
top. The additional statemachine is required to ensure all LinuxKPI
tasklets get serialized. FreeBSD taskqueues do not guarantee
serialisation of its tasks, except when there is only one worker
thread configured.
MFC after: 1 week
Sponsored by: Mellanox Technologies
A set of helper functions have been added to manage the life of the
LinuxKPI task struct. When an external system call or task is invoked,
a check is made to create the task struct by demand. A thread
destructor callback is registered to free the task struct when a
thread exits to avoid memory leaks.
This change lays the ground for emulating the Linux kernel more
closely which is a dependency by the code using the LinuxKPI APIs.
Add new dedicated td_lkpi_task field has been added to struct thread
instead of abusing td_retval[1].
Fix some header file inclusions to make LINT kernel build properly
after this change.
Bump the __FreeBSD_version to force a rebuild of all kernel modules.
MFC after: 1 week
Sponsored by: Mellanox Technologies
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
VesaLocalBus or EISA. Internally, EISA and ISA are handled the same,
with VL being handled slightly differently. To avoid too much code
churn, retain the EISA name, despite it being used only for ISA
bus. When it is on the ISA bus, weird gymnastics are required with
EISA-space address accesses as well. Remove known models from the ahc
man page. Remove ahc_eisa module.
still relevant (ISA cards can still be in EISA mode, and we're still
ignoring those in the identify routine). Notes about cards in EISA
mode have been left in the manual since they aren't relevant to EISA
support, but instruct how to properly configure an ISA card in a mode
when it is in a ISA bus slot.
support. Fix a comment block that's shared with both vx and ep. Remove
obsolete refernce to statically compiling a kernel with a fixed number
of vx devices. Have not removed EISA from the title of the document
the register definitions were originally derived from (though no doubt
more recent docments were also consulted).
but it allows to use 64 bit linux strace(1) on 64 bit linux binaries.
Reviewed by: dchagin (earlier version)
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9406
Refresh upstream driver before impending conversion to iflib.
Major new features:
- Support for Fortville-based 25G adapters
- Support for I2C reads/writes
(To prevent getting or sending corrupt data, you should set
dev.ixl.0.debug.disable_fw_link_management=1 when using I2C
[this will disable link!], then set it to 0 when done. The driver implements
the SIOCGI2C ioctl, so ifconfig -v works for reading I2C data,
but there are read_i2c and write_i2c sysctls under the .debug sysctl tree
[the latter being useful for upper page support in QSFP+]).
- Addition of an iWARP client interface (so the future iWARP driver for
X722 devices can communicate with the base driver).
- Compiling this option in is enabled by default, with "options IXL_IW" in
GENERIC.
Differential Revision: https://reviews.freebsd.org/D9227
Reviewed by: sbruno
MFC after: 2 weeks
Sponsored by: Intel Corporation
Small summary
-------------
o Almost all IPsec releated code was moved into sys/netipsec.
o New kernel modules added: ipsec.ko and tcpmd5.ko. New kernel
option IPSEC_SUPPORT added. It enables support for loading
and unloading of ipsec.ko and tcpmd5.ko kernel modules.
o IPSEC_NAT_T option was removed. Now NAT-T support is enabled by
default. The UDP_ENCAP_ESPINUDP_NON_IKE encapsulation type
support was removed. Added TCP/UDP checksum handling for
inbound packets that were decapsulated by transport mode SAs.
setkey(8) modified to show run-time NAT-T configuration of SA.
o New network pseudo interface if_ipsec(4) added. For now it is
build as part of ipsec.ko module (or with IPSEC kernel).
It implements IPsec virtual tunnels to create route-based VPNs.
o The network stack now invokes IPsec functions using special
methods. The only one header file <netipsec/ipsec_support.h>
should be included to declare all the needed things to work
with IPsec.
o All IPsec protocols handlers (ESP/AH/IPCOMP protosw) were removed.
Now these protocols are handled directly via IPsec methods.
o TCP_SIGNATURE support was reworked to be more close to RFC.
o PF_KEY SADB was reworked:
- now all security associations stored in the single SPI namespace,
and all SAs MUST have unique SPI.
- several hash tables added to speed up lookups in SADB.
- SADB now uses rmlock to protect access, and concurrent threads
can do SA lookups in the same time.
- many PF_KEY message handlers were reworked to reflect changes
in SADB.
- SADB_UPDATE message was extended to support new PF_KEY headers:
SADB_X_EXT_NEW_ADDRESS_SRC and SADB_X_EXT_NEW_ADDRESS_DST. They
can be used by IKE daemon to change SA addresses.
o ipsecrequest and secpolicy structures were cardinally changed to
avoid locking protection for ipsecrequest. Now we support
only limited number (4) of bundled SAs, but they are supported
for both INET and INET6.
o INPCB security policy cache was introduced. Each PCB now caches
used security policies to avoid SP lookup for each packet.
o For inbound security policies added the mode, when the kernel does
check for full history of applied IPsec transforms.
o References counting rules for security policies and security
associations were changed. The proper SA locking added into xform
code.
o xform code was also changed. Now it is possible to unregister xforms.
tdb_xxx structures were changed and renamed to reflect changes in
SADB/SPDB, and changed rules for locking and refcounting.
Reviewed by: gnn, wblock
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D9352
low-quality random numbers with a modern implementation (xoroshiro128+)
that is capable of generating better quality randomness without compromising performance.
Submitted by: Graeme Jenkinson
Reviewed by: markj
MFC after: 2 weeks
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9051
* Clang/llvm does not (yet) support -m(no-)spe, so make it gcc-only
* Clang now supports -msoft-float, and does not appear to recognize
"-disable-ppc-float-in-variadic", which appears to have been a crutch until
soft-float was implemented. It's now implemented for both 32- and 64-bit.
* Clang/llvm use a 'medium' code model by default for powerpc64, supporting up
to 4GB TOC, and does not support the '-mminimal-toc' option. Given both of
these, make -mminimal-toc gcc-only.
MFC after: 2 weeks
Ideally we'd have a top level hwpmc module with the shared bits, then
cpu specific glue as needed. However, on the MIPS side, there's no
probe code - {mips24k, mips74k, octeon} implement a set of methods
that hwpmc_mips.c expects.
So this populates separate modules with duplicate code.
Ew, but it does work.
This gets me off the hook - these work fine as copied into the relevant
mfsroot for mips24k/mips74k systems.
TODO:
* do it the "right" way in the future. Note that modules/hwpmc/ does
build fine on MIPS, it jusn't DO anything. So it'd be nice to
maybe call that "hwpmc_core" and then "hwpmc" can be the CPU/arch glue.
default, and the fewer changes relative to the upstream u-boot the
better.
Add compatibility links for the old names.
Add dts file for BeagleBone Green while we're here.
By default reading the diagnostic counters is disabled. The firmware
decides which counters are supported and only those supported show up
in the dev.mce.X.diagnostics sysctl tree.
To enable reading of diagnostic counters set one or more of the
following sysctls to one:
dev.mce.X.conf.diag_general_enable=1
dev.mce.X.conf.diag_pci_enable=1
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Add RATELIMIT kernel configuration keyword which must be set to
enable the new functionality.
- Add support for hardware driven, Receive Side Scaling, RSS aware, rate
limited sendqueues and expose the functionality through the already
established SO_MAX_PACING_RATE setsockopt(). The API support rates in
the range from 1 to 4Gbytes/s which are suitable for regular TCP and
UDP streams. The setsockopt(2) manual page has been updated.
- Add rate limit function callback API to "struct ifnet" which supports
the following operations: if_snd_tag_alloc(), if_snd_tag_modify(),
if_snd_tag_query() and if_snd_tag_free().
- Add support to ifconfig to view, set and clear the IFCAP_TXRTLMT
flag, which tells if a network driver supports rate limiting or not.
- This patch also adds support for rate limiting through VLAN and LAGG
intermediate network devices.
- How rate limiting works:
1) The userspace application calls setsockopt() after accepting or
making a new connection to set the rate which is then stored in the
socket structure in the kernel. Later on when packets are transmitted
a check is made in the transmit path for rate changes. A rate change
implies a non-blocking ifp->if_snd_tag_alloc() call will be made to the
destination network interface, which then sets up a custom sendqueue
with the given rate limitation parameter. A "struct m_snd_tag" pointer is
returned which serves as a "snd_tag" hint in the m_pkthdr for the
subsequently transmitted mbufs.
2) When the network driver sees the "m->m_pkthdr.snd_tag" different
from NULL, it will move the packets into a designated rate limited sendqueue
given by the snd_tag pointer. It is up to the individual drivers how the rate
limited traffic will be rate limited.
3) Route changes are detected by the NIC drivers in the ifp->if_transmit()
routine when the ifnet pointer in the incoming snd_tag mismatches the
one of the network interface. The network adapter frees the mbuf and
returns EAGAIN which causes the ip_output() to release and clear the send
tag. Upon next ip_output() a new "snd_tag" will be tried allocated.
4) When the PCB is detached the custom sendqueue will be released by a
non-blocking ifp->if_snd_tag_free() call to the currently bound network
interface.
Reviewed by: wblock (manpages), adrian, gallatin, scottl (network)
Differential Revision: https://reviews.freebsd.org/D3687
Sponsored by: Mellanox Technologies
MFC after: 3 months
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
all public firmwares for all chips since the last release (1.15.37.0)
follows (it's a straight copy-paste from the Release Notes for the
12/30/2016 Unified Wire release on Chelsio's website).
T6 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
Fixes
-----
BASE:
- Max number of egress and control queues adjusted to accomodate
co-processor mode queues.
- Fixed intermittent DDR3/4 ECC errors.
- Fixed a traffic stall when ETS BW is configured as 0%.
- Max number of ethctrl queue in VF set to 1.
ETH:
- Added a new config file option 'speed' under port section to set the
port speed. Use only when auto negotiation is off.
- FEC option removed from firmware config file. cxgbtool can be used to
change the fec setting.
- CPL_TX_TNL_LSO cpl handling added in ETH_TX_PKT_VM handler. This fixes
large tunnel tcp packet support for VxLAN.
Version : 1.16.22.0
Date : 12/05/2016
Fixes
-----
BASE:
- fw_port_type updated in fw API to match kernel.org definitions.
- Saved power by disaling unused MAC lanes.
- Configures correct power bin.
- Enhanced DDR4 performance.
- Enabled interrupts.
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Disabled auto negotiation by default because most of 100G switches do
not support AN as of today.
- Fixed flow control not getting disabled problem.
- Fixed an issue where port0 doesn't come up sometimes.
- Fixed 10G link not coming up issue.
- Fixed an issue with promiscuous mode when dcbx disabled.
OFLD:
- Fixed a connection stuck issue when abort is received during out of tx
pages backpressure.
ENHANCEMENTS
------------
BASE:
- Added inline TLS mode support.
Version : 1.16.12.0
Date : 11/11/2016
ENHANCEMENTS
------------
BASE:
- Added T6 support.
- Added T6 1G/10G/25G/40G/100G link speeds.
- Added T6 co-processor mode crypto support.
- Added facility to increase link AN+AEC timeout.
OFLD:
- Added support for all T5 offload protocols except FCoE.
iSCSI:
- iscsi completion moderation enabled.
=======================================================================
T5 Firmware
++++++++++++
Version : 1.16.26.0
Date : 12/28/2016
FIXES
-----
BASE:
- Max number of ethctrl queue in VF set to 1.
Version : 1.16.22.0
Date : 12/05/2016
FIXES
-----
BASE:
- Fixed an issue where filter rule for 'unicast hash' is not working.
ETH:
- Fixed an issue with promiscuous mode when dcbx disabled.
ENHANCEMENTS
------------
ETH:
- Added 40G-KR support.
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed multiple issues related with VFs FLR processing.
- Fixed channel assignment based on number of ports in adapter.
- Fixed a crash when VM having PF assigned as passthrough mode is
rebooted.
- Handled 2nd HELLO command from the same PF without seeing BYE from the
same PF and if that is the only PF.
- A warning is printed in firmware log if PCI-E cookie generation is
enabled in serial initialization file.
- Fixed multiple issues related with Filtering.
- Enabled DSGL memory write for iscsi and rdma.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed DCBX CEE Incorrect class to pririty mapping.
- Fixed incorrect interpretation of DCBX IEEE PFC.
ETH:
- Adjusted the link related delay timings according to the QSFP spec.
- Improved 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
ENHANCEMENTS
------------
BASE:
- Added 10G KR/KX support.
- Added T540-BT adapter support.
- Added 4 new rss key modes for PFs and VFs.
OFLD:
- Added new WR FW_RI_FR_NSMR_TPTE_WR to improve fast MR write
performance in RDMA.
Version : 1.16.5.0
Date : 10/26/2016
FIXES
-----
BASE:
- Fixed multiple issues where FLR from multiple VFs can cause firmware
crash.
- Fixed channel assignment based on number of ports in adapter.
- Fixed the HELLO command master force api to handle the 2nd HELLO
correctly without getting BYE from the PF driver.
- Added facility to retrieve Serial configuration and VPD version. Two
new FW_PARAMS_CMD[DEV] options added to retrieve these values.
- Fixed multiple issues where FLR from multiple VFs are not completing.
- Added new RSS hash secret key modes.
- Fixed an issue where LVDS output was not getting enabled using vpd.
DCBX:
- Fixed an issue where iscsi tlv is sent incorrectly to host (DCBX CEE).
- Fixed an issue where app priority values are not handled correctly
in fw (DCBX IEEE).
ETH:
- Adjusts the link related delay timings according to the QSFP spec.
- Changed 2.5G mac speed bit to 25G mac speed bit in fw API.
- Improvement in 40G link bringup time with few switches.
OFLD:
- Do not reserve qp/cq if rdma capability is not enabled.
- Fixed an issue where approx 1600+ TOE connections were causing a
firmware fatal error.
- Fixed DSGL memory write in T5. Now iwarp and iscsi can use DSGL to do
memory write.
- Fixed multiple issues in hash filter mode where incorrect protocol
mask was getting used and affecting hash filter functionality.
- New fastpath WR FW_RI_FR_NSMR_TPTE_WR (with fully populated TPTE) is
added for small REG_MR operations.
FOiSCSI:
- Fixed an issue in foiscsi recovery path.
- Fixed an issue where foiscsi (in VM in PCIE passthrough mode) didn't
come up after VM FLR.
ENHANCEMENTS
------------
ETH:
- Implemented 1G/10G KR/KX ability.
- Implemented T540-BT adapter support.
=======================================================================
T4 Firmware
+++++++++++
Version : 1.16.12.0
Date : 11/11/2016
FIXES
-----
BASE:
- Fixed an issue where reading temperature sesors using ldst command
causes mailbox timeout.
- Added new FW_PARAMS_CMD[DEV] options to retrieve Serial Configuration
and VPD version numbers.
ETH:
- Fixed DCBX CEE Incorrect class to pririty mapping.
FOiSCSI:
- Fixed an issue where unloading foiscsi driver causes mailbox timeout.
MFC after: 3 days
Sponsored by: Chelsio Communications
(disabled by default).
To enable it, dev.rtwn.%d.radar_detection tunable need to be set
to a nonzero value.
Tested with RTL8821AU, AP mode (no radar events were seen - so,
I have no idea if it is really correct / working)
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D8903
Wake-on-lan is not supported in production on any of our adapters, as
they don't have the required AUX power connector. (It's possible that
AUX power is supplied to some of our ALOM or mezz adapters, but if so
then we've never implemented or tested WoL support.)
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8972
Add SPI mode (PIO-only) support for Intel Synchronous Serial Port that
can be found in several Intel's products starting from PXA family.
Most of implementations have slight differences in behavior and in
addresses for registers subset. This driver covers only BayTrail SoC
implementation for it's the only hardware I have to test it on.
Driver attaches to ACPI bus only and does not have PCI or FDT support
for now due to lack of hardware to test it on.
"intelspi" is the best name I've managed to come up with. Linux driver
name (spi-pxa2xx) does not make sense because current implementation
does not support actual PXA2xx SoCs. And as far as I know there is no
codename assigned to Intel SSP chip.
Reviewed by: br, manu
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D8896
Add ACPI part for ig4 driver to make it work on Intel BayTrail SoC where
ig4 device is available only through ACPI
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8742
This adds support for:
- Serializing an bhnd_nvram_plist (as exported from bhnd_nvram_store, etc) to
an arbitrary NVRAM data format.
- Generating a serialized representation of the current NVRAM store's state
suitable for writing back to flash, or re-encoding for upload to a
FullMAC device.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8762
Implements bhnd_nvram_store support for parsing and operating over NVRAM
device paths, and device path aliases, as well as tracking per-path NVRAM
variable writes.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8760
This adds support for bhnd_nvram_val_convert_init() and
bhnd_nvram_val_convert_new(), which may be used to perform value
format-aware encoding of an NVRAM value to a new target format/type.
This will be used to simplify converting to/from serialized
format-specific NVRAM value representations to common external
representations.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8757
representing arbitrary Broadcom NVRAM key/value pairs.
This will be used to track pending changes in bhnd_nvram_store, and
provide support for exporting all or a device subpath for NVRAM (as
required by some fullmac wifi chipsets).
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D8756
For whatever reason, smapi, smbios, vpd are all under the "bios" directory.
smapi is only for i386, so the entire "bios" directory is only built for
i386. Break smapi out, and make only it i386-specific. Then, build the
"bios" directory for both amd64 and i386.
Reviewed by: imp
MFC after: 1 week
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D8609
