Now when one does 'make kernel ; make kernel' the second invocation
only does: `kernel.ko' is up to date.
rather than reproduce all the .fw files and relink the kernel.
Bring in a driver for the LSI Logic MPT2 6Gb SAS controllers.
This driver supports basic I/O, and works with SAS and SATA drives and
expanders.
Basic error recovery works (i.e. timeouts and aborts) as well.
Integrated RAID isn't supported yet, and there are some known bugs.
So this isn't ready for production use, but is certainly ready for
testing and additional development. For the moment, new commits to this
driver should go into the FreeBSD Perforce repository first
(//depot/projects/mps/...) and then get merged into -current once
they've been vetted.
This has only been added to the amd64 GENERIC, since that is the only
architecture I have tested this driver with.
Submitted by: scottl
Discussed with: imp, gibbs, will
Sponsored by: Yahoo, Spectra Logic Corporation
the existing code was very platform specific, and broken for SMP systems
trying to reboot from KDB.
- Add a new PLATFORM_RESET() method to the platform KOBJ interface, and
migrate existing reset functions into platform modules.
- Modify the OF_reboot() routine to submit the request by hand to avoid
the IPIs involved in the regular openfirmware() routine. This fixes
reboot from KDB on SMP machines.
- Move non-KDB reset and poweroff functions on the Powermac platform
into the relevant power control drivers (cuda, pmu, smu), instead of
using them through the Open Firmware backdoor.
- Rename platform_chrp to platform_powermac since it has become
increasingly Powermac specific. When we gain support for IBM systems,
we will grow a new platform_chrp.
provide PCI devices for various hardware such as memory controllers, etc.
These PCI buses are not enumerated via ACPI however. Add qpi(4) psuedo
bus and Host-PCI bridge drivers to enumerate these buses. Currently the
driver uses the CPU ID to determine the bridges' presence.
In collaboration with: Joseph Golio @ Isilon Systems
MFC after: 2 weeks
Makefiles or *.mk files, use ${CC:T:Mfoo} instead, so only the basename
of the compiler command (excluding any arguments) is considered.
This allows you to use, for example, CC="/nondefault/path/clang -xxx",
and still have the various tests in bsd.*.mk identify your compiler as
clang correctly.
ICC if cases were also changed.
Submitted by: Dimitry Andric <dimitry at andric.com>
As des noted, the section on SCTP would benefit from
a rewrite by a native speaker (which I am not).
Any volunteers?
Approved by: des (mentor)
MFC after: 1 week
zones for each malloc bucket size. The purpose is to isolate
different malloc types into hash classes, so that any buffer overruns
or use-after-free will usually only affect memory from malloc types in
that hash class. This is purely a debugging tool; by varying the hash
function and tracking which hash class was corrupted, the intersection
of the hash classes from each instance will point to a single malloc
type that is being misused. At this point inspection or memguard(9)
can be used to catch the offending code.
Add MALLOC_DEBUG_MAXZONES=8 to -current GENERIC configuration files.
The suggestion to have this on by default came from Kostik Belousov on
-arch.
This code is based on work by Ron Steinke at Isilon Systems.
Reviewed by: -arch (mostly silence)
Reviewed by: zml
Approved by: zml (mentor)
module that can be used by both the regular and experimental nfs
clients. This fixes the problem reported by jh@ where /dev/nfslock
would be registered twice when both nfs clients were used.
I also defined the size of the lm_fh field to be the correct value,
as it should be the maximum size of an NFSv3 file handle.
Reviewed by: jh
MFC after: 2 weeks
The aeskeys_{amd64,i386}.S content was mostly obtained from OpenBSD,
no objections to the license from core.
Hardware provided by: Sentex Communications
Tested by: fabient, pho (previous versions)
MFC after: 1 month
library:
o) Increase inline unit / large function growth limits for MIPS to accommodate
the needs of the Simple Executive, which uses a shocking amount of inlining.
o) Remove TARGET_OCTEON and use CPU_CNMIPS to do things required by cnMIPS and
the Octeon SoC.
o) Add OCTEON_VENDOR_LANNER to use Lanner's allocation of vendor-specific
board numbers, specifically to support the MR320.
o) Add OCTEON_BOARD_CAPK_0100ND to hard-wire configuration for the CAPK-0100nd,
which improperly uses an evaluation board's board number and breaks board
detection at runtime. This board is sold by Portwell as the CAM-0100.
o) Add support for the RTC available on some Octeon boards.
o) Add support for the Octeon PCI bus. Note that rman_[sg]et_virtual for IO
ports can not work unless building for n64.
o) Clean up the CompactFlash driver to use Simple Executive macros and
structures where possible (it would be advisable to use the Simple Executive
API to set the PIO mode, too, but that is not done presently.) Also use
structures from FreeBSD's ATA layer rather than structures copied from
Linux.
o) Print available Octeon SoC features on boot.
o) Add support for the Octeon timecounter.
o) Use the Simple Executive's routines rather than local copies for doing reads
and writes to 64-bit addresses and use its macros for various device
addresses rather than using local copies.
o) Rename octeon_board_real to octeon_is_simulation to reduce differences with
Cavium-provided code originally written for Linux. Also make it use the
same simplified test that the Simple Executive and Linux both use rather
than our complex one.
o) Add support for the Octeon CIU, which is the main interrupt unit, as a bus
to use normal interrupt allocation and setup routines.
o) Use the Simple Executive's bootmem facility to allocate physical memory for
the kernel, rather than assuming we know which addresses we can steal.
NB: This may reduce the amount of RAM the kernel reports you as having if
you are leaving large temporary allocations made by U-Boot allocated
when starting FreeBSD.
o) Add a port of the Cavium-provided Ethernet driver for Linux. This changes
Ethernet interface naming from rgmxN to octeN. The new driver has vast
improvements over the old one, both in performance and functionality, but
does still have some features which have not been ported entirely and there
may be unimplemented code that can be hit in everyday use. I will make
every effort to correct those as they are reported.
o) Support loading the kernel on non-contiguous cores.
o) Add very conservative support for harvesting randomness from the Octeon
random number device.
o) Turn SMP on by default.
o) Clean up the style of the Octeon kernel configurations a little and make
them compile with -march=octeon.
o) Add support for the Lanner MR320 and the CAPK-0100nd to the Simple
Executive.
o) Modify the Simple Executive to build on FreeBSD and to build without
executive-config.h or cvmx-config.h. In the future we may want to
revert part of these changes and supply executive-config.h and
cvmx-config.h and access to the options contained in those files via
kernel configuration files.
o) Modify the Simple Executive USB routines to support getting and setting
of the USB PID.
MACHINE_CPUARCH isn't defined. I believe that this will cover all
options.
I didn't define it in kern.mk because $M is set to MACHINE_CPUARCH and
then is expanded for the genassym.o rule in kern.post.mk and kern.mk
is included after this, so the expansion isn't quite right. I think
this is a bug in make, but don't have the time to track it to ground
(and even if I did, fixing it would require a MFC of the change to the
very old systems we're targetting with this fix).
Kernel sources for 64-bit PowerPC, along with build-system changes to keep
32-bit kernels compiling (build system changes for 64-bit kernels are
coming later). Existing 32-bit PowerPC kernel configurations must be
updated after this change to specify their architecture.
(exec_setregs, etc.) in order to simplify the addition of 64-bit support,
and possible future extension of the Book-E code to handle hard floating
point and Altivec.
MFC after: 1 month
The following systems are affected:
- MPC8555CDS
- MPC8572DS
This overhaul covers the following major changes:
- All integrated peripherals drivers for Freescale MPC85XX SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- This includes: LBC, PCI / PCI-Express, I2C, DS1553, OpenPIC, TSEC, SEC,
QUICC, UART, CFI.
- Thanks to the common FDT infrastrucutre (fdtbus, simplebus) we retire
ocpbus(4) driver, which was based on hard-coded config data.
Note that world for these platforms has to be built WITH_FDT.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
the core changes but left out the shared code, lol.
Well, and a couple fixes to the core... hopefully
this will all be complete now.
Happy happy joy joy :)
It has more features than acpi_aiboost(4) and it will eventually replace
acpi_aiboost(4).
Submitted by: Constantine A. Murenin <cnst at FreeBSD.org>
Reviewed by: freebsd-acpi, imp
MFC after: 1 month
writing event timer drivers, for choosing best possible drivers by machine
independent code and for operating them to supply kernel with hardclock(),
statclock() and profclock() events in unified fashion on various hardware.
Infrastructure provides support for both per-CPU (independent for every CPU
core) and global timers in periodic and one-shot modes. MI management code
at this moment uses only periodic mode, but one-shot mode use planned for
later, as part of tickless kernel project.
For this moment infrastructure used on i386 and amd64 architectures. Other
archs are welcome to follow, while their current operation should not be
affected.
This patch updates existing drivers (i8254, RTC and LAPIC) for the new
order, and adds event timers support into the HPET driver. These drivers
have different capabilities:
LAPIC - per-CPU timer, supports periodic and one-shot operation, may
freeze in C3 state, calibrated on first use, so may be not exactly precise.
HPET - depending on hardware can work as per-CPU or global, supports
periodic and one-shot operation, usually provides several event timers.
i8254 - global, limited to periodic mode, because same hardware used also
as time counter.
RTC - global, supports only periodic mode, set of frequencies in Hz
limited by powers of 2.
Depending on hardware capabilities, drivers preferred in following orders,
either LAPIC, HPETs, i8254, RTC or HPETs, LAPIC, i8254, RTC.
User may explicitly specify wanted timers via loader tunables or sysctls:
kern.eventtimer.timer1 and kern.eventtimer.timer2.
If requested driver is unavailable or unoperational, system will try to
replace it. If no more timers available or "NONE" specified for second,
system will operate using only one timer, multiplying it's frequency by few
times and uing respective dividers to honor hz, stathz and profhz values,
set during initial setup.
This information can be very valuable for CPU sleep-time (and respectively
idle power consumption) optimization.
Add counters for timer-related IPIs.
Reviewed by: jhb@ (previous version)
The following systems are involved:
- DB-88F5182
- DB-88F5281
- DB-88F6281
- DB-78100
- SheevaPlug
This overhaul covers the following major changes:
- All integrated peripherals drivers for Marvell ARM SoC, which are
currently in the FreeBSD source tree are reworked and adjusted so they
derive config data out of the device tree blob (instead of hard coded /
tabelarized values).
- Since the common FDT infrastrucutre (fdtbus, simplebus) is used we say
good by to obio / mbus drivers and numerous hard-coded config data.
Note that world needs to be built WITH_FDT for the affected platforms.
Reviewed by: imp
Sponsored by: The FreeBSD Foundation.
passing through. Modifications are restricted to a subset of C language
operations on unsigned integers of 8, 16, 32 or 64 bit size.
These are: set to new value (=), addition (+=), subtraction (-=),
multiplication (*=), division (/=), negation (= -), bitwise AND (&=),
bitwise OR (|=), bitwise eXclusive OR (^=), shift left (<<=),
shift right (>>=). Several operations are all applied to a packet
sequentially in order they were specified by user.
Submitted by: Maxim Ignatenko <gelraen.ua at gmail.com>
Vadim Goncharov <vadimnuclight at tpu.ru>
Discussed with: net@
Approved by: mav (mentor)
MFC after: 1 month
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
Extend struct sysvec with three new elements:
sv_fetch_syscall_args - the method to fetch syscall arguments from
usermode into struct syscall_args. The structure is machine-depended
(this might be reconsidered after all architectures are converted).
sv_set_syscall_retval - the method to set a return value for usermode
from the syscall. It is a generalization of
cpu_set_syscall_retval(9) to allow ABIs to override the way to set a
return value.
sv_syscallnames - the table of syscall names.
Use sv_set_syscall_retval in kern_sigsuspend() instead of hardcoding
the call to cpu_set_syscall_retval().
The new functions syscallenter(9) and syscallret(9) are provided that
use sv_*syscall* pointers and contain the common repeated code from
the syscall() implementations for the architecture-specific syscall
trap handlers.
Syscallenter() fetches arguments, calls syscall implementation from
ABI sysent table, and set up return frame. The end of syscall
bookkeeping is done by syscallret().
Take advantage of single place for MI syscall handling code and
implement ptrace_lwpinfo pl_flags PL_FLAG_SCE, PL_FLAG_SCX and
PL_FLAG_EXEC. The SCE and SCX flags notify the debugger that the
thread is stopped at syscall entry or return point respectively. The
EXEC flag augments SCX and notifies debugger that the process address
space was changed by one of exec(2)-family syscalls.
The i386, amd64, sparc64, sun4v, powerpc and ia64 syscall()s are
changed to use syscallenter()/syscallret(). MIPS and arm are not
converted and use the mostly unchanged syscall() implementation.
Reviewed by: jhb, marcel, marius, nwhitehorn, stas
Tested by: marcel (ia64), marius (sparc64), nwhitehorn (powerpc),
stas (mips)
MFC after: 1 month
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
HAL/Fujitsu) CPUs. For the most part this consists of fleshing out the
MMU and cache handling, it doesn't add pmap optimizations possible with
these CPU, yet, though.
With these changes FreeBSD runs stable on Fujitsu Siemens PRIMEPOWER 250
and likely also other models based on SPARC64 V like 450, 650 and 850.
Thanks go to Michael Moll for providing access to a PRIMEPOWER 250.
driver for CAM ATA subsystem. This driver supports same hardware as
atamarvell, ataadaptec and atamvsata drivers from ata(4), but provides
many additional features, such as NCQ, PMP, etc.
that generates a fatal bus trap. Normally, the chips are setup to do
128 byte DMA bursts, but when on this CPU, they can only safely due
4-byte DMA bursts due to this bug. Details of the exact nature of the
bug are sketchy, but some can be found at
https://forum.openwrt.org/viewtopic.php?pid=70060 on pages 4, 5 and 6.
There's a small performance penalty associated with this workaround,
so it is only enabled when needed on the Atheros AR71xx platforms.
Unfortunately, this condition is impossible to detect at runtime
without MIPS specific ifdefs. Rather than cast an overly-broad net
like Linux/OpenWRT dues (which enables this workaround all the time on
MIPS32 platforms), we put this option in the kernel for just the
affected machines. Sam didn't like this aspect of the patch when he
reviewed it, and I'd love to hear sane proposals on how to fix it :)
Reviewed by: sam@
with all other corresponding CTF places by changing the corresponding
code which is generated by config(8). Or in short, move the '@' from
the variable definition to the use of the variable. [1]
While I'm here break up a long line. [2]
Discussed with: imp [1,2], bde [2]
This driver was written by Alexander Pohoyda and greatly enhanced
by Nikolay Denev. I don't have these hardwares but this driver was
tested by Nikolay Denev and xclin.
Because SiS didn't release data sheet for this controller, programming
information came from Linux driver and OpenSolaris. Unlike other open
source driver for SiS190/191, sge(4) takes full advantage of TX/RX
checksum offloading and does not require additional copy operation in
RX handler.
The controller seems to have advanced offloading features like VLAN
hardware tag insertion/stripping, TCP segmentation offload(TSO) as
well as jumbo frame support but these features are not available
yet. Special thanks to xclin <xclin<> cs dot nctu dot edu dot tw>
who sent fix for receiving VLAN oversized frames.
StarCat systems which provides time-of-day services for both as well as
console service for Serengeti, i.e. Sun Fire V1280. While the latter is
described with a device type of serial in the OFW device tree, it isn't
actually an UART. Nevertheless the console service is handled by uart(4)
as this allowed to re-use quite a bit of MD and MI code. Actually, this
idea is stolen from Linux which interfaces the sun4v hypervisor console
with the Linux counterpart of uart(4).
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
domain clock, 8 programmable PMC.
- Westmere based CPU (Xeon 5600, Corei7 980X) support.
- New man pages with events list for core and uncore.
- Updated Corei7 events with Intel 253669-033US December 2009 doc.
There is some removed events in the documentation, they have been
kept in the code but documented in the man page as obsolete.
- Offcore response events can be setup with rsp token.
Sponsored by: NETASQ
are some problems with static executables), make.conf (would also
affect ports which do not use GNU make and do not override the
compile targets) or in the kernel config (via "makeoptions
WITH_CTF=yes").
Additional (related) changes:
- propagate WITH_CTF to module builds
- do not add -g to the linker flags, it's a noop there anyway
(at least according to the man page of ld)
- do not add -g to CFLAGS unconditionally
we need to have a look if it is really needed (IMO not) or if there
is a way to add it only when WITH_CTF is used
Note: ctfconvert / ctfmerge lines will not appear in the build output,
to protect the innocent (those which do not build with WITH_CTF would
see the shell-test and may think WITH_CTF is used).
Reviewed by: imp, jhb, scottl (earlier version)
Discussed on: arch@
em revision 7.0.0:
- Using driver devclass, seperate legacy (pre-pcie) code
into a seperate source file. This will at least help
protect against regression issues. It compiles along
with em, and is transparent to end use, devices in each
appear to be 'emX'. When using em in a modular form this
also allows the legacy stuff to be defined out.
- Add tx and rx rings as in igb, in the 82574 this becomes
actual multiqueue for the first time (2 queues) while in
other PCIE adapters its just make code cleaner.
- Add RX mbuf handling logic that matches igb, this will
eliminate packet drops due to temporary mbuf shortage.
igb revision 1.9.3:
- Following the ixgbe code, use a new approach in what
was called 'get_buf', the routine now has been made
independent of rxeof, it now does the update to the
engine TDT register, this design allows temporary
mbuf resources to become non-critical, not requiring
a packet to be discarded, instead it just returns and
does not increment the tail pointer.
- With the above change it was also unnecessary to keep
'spare' maps around, since we do not have the discard
issue.
- Performance tweaks and improvements to the code also.
MFC in a week
for upcoming 64-bit PowerPC and MIPS support. This renames the COMPAT_IA32
option to COMPAT_FREEBSD32, removes some IA32-specific code from MI parts
of the kernel and enhances the freebsd32 compatibility code to support
big-endian platforms.
Reviewed by: kib, jhb
